HIR89-01C/1R

HIR89-01C/1R
Features
․Low forward voltage.
․View angle 30° (Typ.)
․Pb free
․The product itself will remain within RoHS compliant version.
․Compatible with infrared and vapor phase reflow solder process
․Taping as Top view.
Description
․ HIR89-01C/1R is an infrared emitting diode with miniature MIDLED package.
․ The device is spectrally matched with silicon photodiode and phototransistor.
Applications
․Infrared applied system
Device Selection Guide
Device No.
HIR89-01C/1R
1
Chip Material
GaAlAs
Lens Color
Water clear
Copyright © 2010, Everlight All Rights Reserved. Release Date : MAY.20.2013. Issue No: DIR-0000413
www.everlight.com
DATASHEET
HIR89-01C/1R
Package Dimensions
Notes: 1.All dimensions are in millimeters
2.Tolerances unless dimensions ±0.1mm
Absolute Maximum Ratings (Ta=25℃
℃)
Parameter
Continuous Forward Current
Peak Forward Current
*1
Reverse Voltage
Operating Temperature
Storage Temperature
Soldering Temperature
*2
Power Dissipation at(or below)
25℃Free Air Temperature
Symbol
IF
IFP
VR
Topr
Tstg
Tsol
Pd
Rating
65
200
5
-40 ~ +85
-40 ~ +100
260
100
Unit
mA
mA
V
℃
℃
℃
mW
Notes: *1: IFP Conditions--Pulse Width≦500μs and Duty≦5%.
*2: Soldering time≦5 seconds.
2
Copyright © 2010, Everlight All Rights Reserved. Release Date : MAY.20.2013. Issue No: DIR-0000413
www.everlight.com
DATASHEET
HIR89-01C/1R
Electro-Optical Characteristics (Ta=25℃
℃)
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Radiant Intensity
Ie
40
--
125
mW /sr
IF=70mA ,tp=20ms
Peak Wavelength
λp
--
850
--
nm
IF=100mA
Spectral Bandwidth
Δλ
--
30
--
nm
IF=100mA
--
1.40
1.70
Forward Voltage
VF
Reverse Current
View Angle
IF=20mA
V
--
1.55
1.90
IF=70mA,tp=20ms
IR
--
--
10
μA
VR=5V
2θ1/2
--
30
--
deg
IF=20mA
Rank
Condition:IF=70mA
Unit:mW/sr
Bin Number
Min
Max
3
C
40
80
D
63
125
Copyright © 2010, Everlight All Rights Reserved. Release Date : MAY.20.2013. Issue No: DIR-0000413
www.everlight.com
DATASHEET
HIR89-01C/1R
Typical Electrical/Optical/Characteristics Curves for IR
Spectral Distribution
Power Dissipation vs. Ambient Temperature
140
120
100
80
60
40
20
0
-25
0
20
40
60
80
100
Forward Current vs. Forward Voltage
Relative Intensity vs. Forward Current
4
10
Ie-Radiant Intensity(mW/sr)
1000
3
10
2
10
1
10
100
10
0
0
1
2
3
4
5
6
7
8
10
0
10
1
2
10
10
3
10 4
IF-Forward Current (mA)
4
Copyright © 2010, Everlight All Rights Reserved. Release Date : MAY.20.2013. Issue No: DIR-0000413
www.everlight.com
DATASHEET
HIR89-01C/1R
Relative Radiant Intensity vs. Angular Displacement
-20
-10
0
10
20
30
1.0
40
0.9
50
0.8
0.7
60
70
80
0.6 0.4 0.2
5
0
0.2 0.4 0.6
Copyright © 2010, Everlight All Rights Reserved. Release Date : MAY.20.2013. Issue No: DIR-0000413
www.everlight.com
DATASHEET
HIR89-01C/1R
Precautions For Use
1. Over-current-proof
Customer must apply resistors for protection , otherwise slight voltage shift will cause big
current change ( Burn out will happen ).
2. Storage
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less.
2.3 The LEDs should be used within a year.
2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less.
2.5 The LEDs should be used within 168 hours (7 days) after opening the package
2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage
time, baking treatment should be performed using the following conditions.
Baking treatment : 60±5℃ for 24 hours.
3. Soldering Condition
3.1 Pb-free solder temperature profile
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
6
Copyright © 2010, Everlight All Rights Reserved. Release Date : MAY.20.2013. Issue No: DIR-0000413
www.everlight.com
DATASHEET
HIR89-01C/1R
4. Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within
once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering
of each terminal. Be careful because the damage of the product is often started at the time of the hand
solder.
5. Repairing
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a
double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the
characteristics of the LEDs will or will not be damaged by repairing.
7
Copyright © 2010, Everlight All Rights Reserved. Release Date : MAY.20.2013. Issue No: DIR-0000413
www.everlight.com
DATASHEET
HIR89-01C/1R
Package Dimensions
Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm
2. Carrier Tape Dimensions:(Quantity: 2000pcs/reel)
1
2
1
2
1
2
Anode
Cathode
Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm
8
Copyright © 2010, Everlight All Rights Reserved. Release Date : MAY.20.2013. Issue No: DIR-0000413
www.everlight.com
DATASHEET
HIR89-01C/1R
Packing Procedure
Aluminum moistue-proof bag
Label
Desiccant
Label
Label Form Specification
Pb
EVERLIGHT
CPN :
P N : XXXXXXXXXXXXX
RoHS
XXXXXXXXXXXXX
QTY : XXX
CAT : XXX
HUE : XXX
REF : XXX
LOT NO : XXXXXXXXXX
Reference : XXXXXXXX
CPN: Customer’s Production Number
P/N : Production Number
QTY: Packing Quantity
CAT: Ranks
HUE: Peak Wavelength
REF: Reference
LOT No: Lot Number
MADE IN TAIWAN: Production Place
Notes
1. Above specification may be changed without notice. EVERLIGHT will reserve authority on
material change for above specification.
2. When using this product, please observe the absolute maximum ratings and the instructions
for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for
any damage resulting from use of the product which does not comply with the absolute
maximum ratings and the instructions included in these specification sheets.
3. These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please
don’t reproduce or cause anyone to reproduce them without EVERLIGHT’s
consent.
EVERLIGHT ELECTRONICS CO., LTD.
Office: No 6-8, Zhonghua Rd., Shulin Dist.,
New Taipei City 23860, Taiwan, R.O.C
9
Tel: 886-2-2685-6688
Fax: 886-2-2685-6699
http://www.everlight.com
Copyright © 2010, Everlight All Rights Reserved. Release Date : MAY.20.2013. Issue No: DIR-0000413
www.everlight.com