1.6mm Round Subminiature Reverse Package Phototransistor PT26-21C/TR8 Features ․Fast response time ․High photo sensitivity ․Small junction capacitance ․Pb free ․The product itself will remain within RoHS compliant version. Descriptions ․PT26-21C/TR8 is a phototransistor in miniature SMD package which is molded in a water clear with spherical top view lens. The device is Spectrally matched to visible and infrared emitting diode. Applications ․Miniature switch ․Counters and sorter ․Position sensor ․Infrared applied system ․Encoder Device Selection Guide 1 Part Category Chip Material Lens Color PT Silicon Water Clear Copyright © 2013, Everlight All Rights Reserved. Release Date :6/24/2013 Issue No:DPT-0000247 Rev 3 Revision :3 LifecyclePhase: www.everlight.com Release Date:2013-07-05 13:46:34.0 Expired Period: Forever Technical Data Sheet 1.6mm Round Subminiature Reverse Package Phototransistor PT26-21C/TR8 Package Dimensions Notes: 1.All dimensions are in millimeters 2.Tolerances unless dimensions ±0.1mm Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Units Collector-Emitter Voltage VCEO 30 V Emitter-Collector-Voltage VECO 5 V IC 20 mA Operating Temperature Topr -25 ~ +85 ℃ Storage Temperature Tstg -40 ~ +85 ℃ Soldering Temperature *1 Tsol 260 ℃ Power Dissipation at(or below) 25℃Free Air Temperature Pd 75 mW Collector Current Notes: *1:Soldering time≦5 seconds. 2 Copyright © 2013, Everlight All Rights Reserved. Release Date :6/24/2013 Issue No:DPT-0000247 Revision :3 LifecyclePhase: Rev 3 www.everlight.com Release Date:2013-07-05 13:46:34.0 Expired Period: Forever Technical Data Sheet 1.6mm Round Subminiature Reverse Package Phototransistor PT26-21C/TR8 Electro-Optical Characteristics (Ta=25℃) Parameter 3 Symbol Condition Min Typ Max Unit Rang Of Spectral Bandwidth λ0.5 --- 400 --- 1100 nm Wavelength Of Peak Sensitivity λP --- --- 940 --- nm Collector-Emitter Breakdown Voltage BVCEO IC=100μA Ee=0mW/cm2 30 --- --- V Emitter-Collector Breakdown Voltage BVECO 5 --- --- V Collector-Emitter Saturation Voltage VCE(sat) --- --- 0.4 V --- --- 100 nA 0.3 2.6 --- mA Collector Dark Current ICEO On State Collector Current IC(ON) IE=100μA Ee=0mW/cm2 IC=2mA Ee=1mW/cm2 VCE=20V Ee=0mW/cm2 VCE=5V Ee=1mW/cm2 Copyright © 2013, Everlight All Rights Reserved. Release Date :6/24/2013 Issue No:DPT-0000247 Revision :3 LifecyclePhase: Rev 3 www.everlight.com Release Date:2013-07-05 13:46:34.0 Expired Period: Forever Technical Data Sheet 1.6mm Round Subminiature Reverse Package Phototransistor PT26-21C/TR8 Typical Electro-Optical Characteristics Curves Fig.1 Spectral Sensitivity Fig.2 Collector Current vs. Irradiance 10 1.0 Ta=25 C 0.8 C 1 0.6 0.1 0.4 0.01 0.2 0 100 300 500 700 900 1100 1300 0.001 0.01 0.1 1 10 2 Fig.3 Collector Current vs. Collector-EmitterVoltage 4 Copyright © 2013, Everlight All Rights Reserved. Release Date :6/24/2013 Issue No:DPT-0000247 Revision :3 LifecyclePhase: Rev 3 www.everlight.com Release Date:2013-07-05 13:46:34.0 Expired Period: Forever Technical Data Sheet 1.6mm Round Subminiature Reverse Package Phototransistor PT26-21C/TR8 Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30℃ or less and 60%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 5 Copyright © 2013, Everlight All Rights Reserved. Release Date :6/24/2013 Issue No:DPT-0000247 Revision :3 LifecyclePhase: Rev 3 www.everlight.com Release Date:2013-07-05 13:46:34.0 Expired Period: Forever Technical Data Sheet 1.6mm Round Subminiature Reverse Package Phototransistor PT26-21C/TR8 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. 6 Copyright © 2013, Everlight All Rights Reserved. Release Date :6/24/2013 Issue No:DPT-0000247 Revision :3 LifecyclePhase: Rev 3 www.everlight.com Release Date:2013-07-05 13:46:34.0 Expired Period: Forever Technical Data Sheet 1.6mm Round Subminiature Reverse Package Phototransistor PT26-21C/TR8 Package Dimensions Note: The tolerances unless mentioned are ±0.1, unit=mm. Carrier Taping Dimensions: (Quantity: 1500PCS/Reel) Note: The tolerances unless mentioned are ±0.1, unit=mm. 7 Copyright © 2013, Everlight All Rights Reserved. Release Date :6/24/2013 Issue No:DPT-0000247 Revision :3 LifecyclePhase: Rev 3 www.everlight.com Release Date:2013-07-05 13:46:34.0 Expired Period: Forever Technical Data Sheet 1.6mm Round Subminiature Reverse Package Phototransistor PT26-21C/TR8 Label Form Specification CPN: Customer’s Production Number P/N : Production Number QTY: Packing Quantity CAT: Ranks HUE: Peak Wavelength REF: Reference LOT No: Lot Number Notes 1. Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above specification. 2. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. 3. These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please don’t reproduce or cause anyone to reproduce them without EVERLIGHT’s consent. EVERLIGHT ELECTRONICS CO., LTD. Office: No. 6-8, Zhonghua Rd., Shulin Dist., New Taipei City 23860, Taiwan 8 Tel: 886-2-2685-6688 Fax: 886-2685-2699,6897 http://www.everlight.com Copyright © 2013, Everlight All Rights Reserved. Release Date :6/24/2013 Issue No:DPT-0000247 Revision :3 LifecyclePhase: Rev 3 www.everlight.com Release Date:2013-07-05 13:46:34.0 Expired Period: Forever