0.8mm Height Flat Top Infrared LED HIR19-21C/L11/TR8 Features ․High reliability ․Small double-end package ․Peak wavelength λp=850nm ․Package in 8mm tape on 7” diameter reel ․Low forward voltage ․Pb free ․The product itself will remain within RoHS compliant version. Descriptions ․HIR19-21C/L11/TR8 is an infrared emitting diode in miniature SMD package which is molded in a water clear plastic with flat top view lens. ․The device is spectrally matched with silicon photodiode and phototransistor. Applications ․PCB mounted infrared sensor ․Infrared remote control units with high power requirement ․Smoke detector ․Infrared applied system Device Selection Guide Part Category HIR 1 Chip Material Lens Color GaAlAs Water clear Copyright © 2013, Everlight All Rights Reserved. Release Date : 5/28/2013. Issue No: DIR-0000956. Rev:4 Revision :4 LifecyclePhase: www.everlight.com Release Date:2013-06-10 17:28:46.0 Expired Period: Forever Data Sheet 0.8mm Height Flat Top Infrared LED HIR19-21C/L11/TR8 Package Dimensions Notes: 1.All dimensions are in millimeters 2.Tolerances unless dimensions ±0.1mm Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Continuous Forward Current IF 65 Units mA Reverse Voltage VR 5 V Operating Temperature Topr -25 ~ +85 ℃ Storage Temperature Tstg -40 ~ +85 ℃ Soldering Temperature *1 Tsol 260 ℃ Power Dissipation at(or below) 25℃Free Air Temperature Pd 130 mW Notes: *1:Soldering time≦5 seconds. 2 Copyright © 2013, Everlight All Rights Reserved. Release Date : 5/28/2013. Issue No: DIR-0000956.Rev:4 Revision :4 LifecyclePhase: www.everlight.com Release Date:2013-06-10 17:28:46.0 Expired Period: Forever Data Sheet 0.8mm Height Flat Top Infrared LED HIR19-21C/L11/TR8 Electro-Optical Characteristics (Ta=25℃) Parameter Condition IF=20mA Min. Typ. Max. Radiant Intensity Symbol Ie 0.2 0.8 Peak Wavelength λp IF=20mA -- 850 --- Spectral Bandwidth Δλ IF=20mA -- 45 -- nm Forward Voltage VF IF=20mA 1.45 1.65 V Reverse Current IR 2θ1/2 VR=5V --- -- 10 μA IF=20mA -- 145 -- deg View Angle 3 Copyright © 2013, Everlight All Rights Reserved. Release Date : 5/28/2013. Issue No: DIR-0000956.Rev:4 Revision :4 LifecyclePhase: Units mW /sr nm www.everlight.com Release Date:2013-06-10 17:28:46.0 Expired Period: Forever Data Sheet 0.8mm Height Flat Top Infrared LED HIR19-21C/L11/TR8 Typical Electro-Optical Characteristics Curves Fig.1 Forward Current vs. Ambient Temperature Fig.2 Spectral Distributio n 140 100 120 IF=20mA Ta=25° C 80 100 60 80 60 40 40 20 20 0 0 -25 0 20 40 Fig.3 Forward Current vs. Forward Voltage 4 60 80 100 790 810 830 850 870 890 910 930 950 Fig.4 Relative Intensity vs. Forward Current Copyright © 2013, Everlight All Rights Reserved. Release Date : 5/28/2013. Issue No: DIR-0000956.Rev:4 Revision :4 LifecyclePhase: www.everlight.com Release Date:2013-06-10 17:28:46.0 Expired Period: Forever Data Sheet 0.8mm Height Flat Top Infrared LED HIR19-21C/L11/TR8 Typical Electro-Optical Characteristics Curves Fig.5 Relative Radiant Intensity vs. Angular Displacement 5 Copyright © 2013, Everlight All Rights Reserved. Release Date : 5/28/2013. Issue No: DIR-0000956.Rev:4 Revision :4 LifecyclePhase: www.everlight.com Release Date:2013-06-10 17:28:46.0 Expired Period: Forever Data Sheet 0.8mm Height Flat Top Infrared LED HIR19-21C/L11/TR8 Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 6 Copyright © 2013, Everlight All Rights Reserved. Release Date : 5/28/2013. Issue No: DIR-0000956.Rev:4 Revision :4 LifecyclePhase: www.everlight.com Release Date:2013-06-10 17:28:46.0 Expired Period: Forever Data Sheet 0.8mm Height Flat Top Infrared LED HIR19-21C/L11/TR8 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. 7 Copyright © 2013, Everlight All Rights Reserved. Release Date : 5/28/2013. Issue No: DIR-0000956.Rev:4 Revision :4 LifecyclePhase: www.everlight.com Release Date:2013-06-10 17:28:46.0 Expired Period: Forever Data Sheet 0.8mm Height Flat Top Infrared LED HIR19-21C/L11/TR8 Package Dimensions Note: The tolerances unless mentioned are ±0.1, unit=mm. Carrier Taping Dimensions: Loaded Quantity Per Reel 3000PCS/Reel Note: The tolerances unless mentioned is ±0.1mm, Unit = mm 8 Copyright © 2013, Everlight All Rights Reserved. Release Date : 5/28/2013. Issue No: DIR-0000956.Rev:4 Revision :4 LifecyclePhase: www.everlight.com Release Date:2013-06-10 17:28:46.0 Expired Period: Forever Data Sheet 0.8mm Height Flat Top Infrared LED HIR19-21C/L11/TR8 Label Form Specification CPN: Customer’s Production Number P/N : Production Number QTY: Packing Quantity CAT: Ranks HUE: Peak Wavelength REF: Reference LOT No: Lot Number Notes 1. Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above specification. 2. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. 3. These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please don’t reproduce or cause anyone to reproduce them without EVERLIGHT’s consent. EVERLIGHT ELECTRONICS CO., LTD. Office: No. 6-8, Zhonghua Rd., Shulin Dist., New Taipei City 23860, Taiwan 9 Tel: 886-2-2685-6688 Fax: 886-2685-2699，6897 http://www.everlight.com Copyright © 2013, Everlight All Rights Reserved. Release Date : 5/28/2013. Issue No: DIR-0000956.Rev:4 Revision :4 LifecyclePhase: www.everlight.com Release Date:2013-06-10 17:28:46.0 Expired Period: Forever