Technical Data Sheet 0603 Package Infrared Chip LED SIR19-315/TR8 Features ․Small double-end package ․Peak wavelength λp=870nm ․Package in 8mm tape on 7” diameter reel ․Compatible with infrared and vapor phase reflow solder process. ․Pb free ․The product itself will remain within RoHS compliant version. Description SIR19-315/TR8 is an infrared emitting diode in miniature SMD package which is molded in a water clear epoxy. The device is spectrally matched with silicon photodiode and phototransistor. Applications ․PCB mounted infrared sensor ․Infrared remote control units with high power requirement ․Scanner ․Infrared applied system Device Selection Guide Device No. SIR19-315/TR8 1 Copyright Revision :5 © LifecyclePhase: Chip Material AlGaAs Lens Color Water clear Release Date:2014-08-18 19:21:45.0 2010, Everlight All Rights Reserved. Release Date : Aug.15.2014. Issue No: DIR-0000356 Rev.5 www.everlight.com Expired Period: Forever DATASHEET SIR19-315/TR8 Package Dimensions Notes: 1.All dimensions are in millimeters 2.Tolerances unless dimensions ±0.1mm Absolute Maximum Ratings (Ta=25℃) Parameter Continuous Forward Current Reverse Voltage Operating Temperature Storage Temperature Soldering Temperature *1 Power Dissipation at(or below) 25℃Free Air Temperature Symbol Rating Unit IF VR Topr Tstg Tsol 65 5 -25 ~ +85 -40 ~ +100 260 mA V ℃ ℃ ℃ Pd 110 mW Notes: *1:Soldering time≦5 seconds. 2 Copyright Revision :5 © LifecyclePhase: Release Date:2014-08-18 19:21:45.0 2010, Everlight All Rights Reserved. Release Date : Aug.15.2014. Issue No: DIR-0000356 Rev.5 www.everlight.com Expired Period: Forever DATASHEET SIR19-315/TR8 Electro-Optical Characteristics (Ta=25℃) Parameter Symbol Min. Typ. Max. Unit Condition Radiant Intensity Ie 1.0 1.3 -- mW /sr IF=20mA Peak Wavelength λp 860 870 900 nm IF=20mA Spectral Bandwidth Δλ -- 45 -- nm IF=20mA Forward Voltage VF 1.20 1.35 1.70 V IF=20mA Reverse Current IR -- -- 10 μA VR=5V 2θ1/2 -- 140 -- deg IF=20mA View Angle 3 Copyright Revision :5 © LifecyclePhase: Release Date:2014-08-18 19:21:45.0 2010, Everlight All Rights Reserved. Release Date : Aug.15.2014. Issue No: DIR-0000356 Rev.5 www.everlight.com Expired Period: Forever DATASHEET SIR19-315/TR8 Typical Electrical/Optical/Characteristics Curves Spectral Distribution Forward Current vs. Ambient Temperature 140 100 120 80 IF=20mA Ta=25°C 100 60 80 40 60 40 20 20 0 0 -25 0 20 40 60 80 100 Peak Emission Wavelength vs. Ambient Temperature 910 810 830 850 870 890 910 930 950 970 Forward Voltage vs Ambient Temperature(°C) 1.5 890 1.4 IF=20mA 870 1.3 850 830 -25 4 Copyright Revision :5 © LifecyclePhase: 0 25 50 75 100 1.2 25 50 75 100 120 Release Date:2014-08-18 19:21:45.0 2010, Everlight All Rights Reserved. Release Date : Aug.15.2014. Issue No: DIR-0000356 Rev.5 www.everlight.com Expired Period: Forever DATASHEET SIR19-315/TR8 Relative Intensity vs Ambient Temperature(°C) Relative Radiant Intensity vs. Angular Displacement 2.0 -20 -10 0 10 20 30 1.5 IF=20mA 1.0 1.0 40 0.9 50 0.8 0.7 60 70 80 0 25 5 Copyright Revision :5 © LifecyclePhase: 50 75 100 120 0.6 0.4 0.2 0 0.2 0.4 0.6 Release Date:2014-08-18 19:21:45.0 2010, Everlight All Rights Reserved. Release Date : Aug.15.2014. Issue No: DIR-0000356 Rev.5 www.everlight.com Expired Period: Forever DATASHEET SIR19-315/TR8 Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30℃ or less and 60%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for Min. 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 6 Copyright Revision :5 © LifecyclePhase: Release Date:2014-08-18 19:21:45.0 2010, Everlight All Rights Reserved. Release Date : Aug.15.2014. Issue No: DIR-0000356 Rev.5 www.everlight.com Expired Period: Forever DATASHEET SIR19-315/TR8 4. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5. Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. 7 Copyright Revision :5 © LifecyclePhase: Release Date:2014-08-18 19:21:45.0 2010, Everlight All Rights Reserved. Release Date : Aug.15.2014. Issue No: DIR-0000356 Rev.5 www.everlight.com Expired Period: Forever DATASHEET SIR19-315/TR8 Package Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm 2. Carrier Tape Dimensions:(Quantity: 4000pcs/reel) Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm 8 Copyright Revision :5 © LifecyclePhase: Release Date:2014-08-18 19:21:45.0 2010, Everlight All Rights Reserved. Release Date : Aug.15.2014. Issue No: DIR-0000356 Rev.5 www.everlight.com Expired Period: Forever DATASHEET SIR19-315/TR8 Packing Procedure Aluminum moistue-proof bag Label Desiccant Label Label Form Specification Pb EVERLIGHT CPN : P N : XXXXXXXXXXXXX RoHS XXXXXXXXXXXXX CAT : XXX HUE : XXX REF : XXX QTY : XXX LOT NO : XXXXXXXXXX Reference : XXXXXXXX CPN: Customer’s Production Number P/N : Production Number QTY: Packing Quantity CAT: Ranks HUE: Peak Wavelength REF: Reference LOT No: Lot Number MADE IN TAIWAN: Production Place Notes 1. Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above specification. 2. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. 3. These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please don’t reproduce or cause anyone to reproduce them without EVERLIGHT’s consent. 9 Copyright Revision :5 © LifecyclePhase: Release Date:2014-08-18 19:21:45.0 2010, Everlight All Rights Reserved. Release Date : Aug.15.2014. Issue No: DIR-0000356 Rev.5 www.everlight.com Expired Period: Forever