SIR67-21C/TR8 Features ․Peak wavelength λp=875nm. ․Low forward voltage. ․Compatible with infrared and vapor phase reflow solder process. ․Package in 8mm tape on 7” diameter reels. ․Pb free ․The product itself will remain within RoHS compliant version. Description ․ SIR67-21C/TR8 is an infrared emitting diode in miniature SMD package which is molded in a water clear plastic with flat top view lens. ․ The device is spectrally matched with silicon photodiode and phototransistor. Applications ․Floppy disk drive ․Optoelectronic switch ․Camera ․VCR ․Video ․Smoke detector Device Selection Guide Device No. SIR67-21C/TR8 1 Copyright Revision :1 © LifecyclePhase: Chip Material GaAlAs Lens Color Water clear Date:2013-06-03 15:22:49.0 2010, Everlight All Rights Reserved. Release Date : MAY.20.2013. Issue Release No: DIR-0000957 www.everlight.com Expired Period: Forever DATASHEET SIR67-21C/TR8 Package Dimensions 1.8 1.6 1.8 Notes: 1.All dimensions are in millimeters 2.Tolerances unless dimensions ±0.1mm Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Continuous Forward Current Peak Forward Current *1 Reverse Voltage Operating Temperature Storage Temperature Soldering Temperature *2 Power Dissipation at(or below) 25℃Free Air Temperature IF IFP VR Topr Tstg Tsol Pd Rating 65 1.0 5 -25 ~ +85 -40 ~ +100 260 130 Unit mA A V ℃ ℃ ℃ mW Notes: *1:IFP Conditions--Pulse Width≦100μs and Duty≦1%. *2:Soldering time≦5 seconds. 2 Copyright Revision :1 © LifecyclePhase: Date:2013-06-03 15:22:49.0 2010, Everlight All Rights Reserved. Release Date : MAY.20.2013. Issue Release No: DIR-0000957 www.everlight.com Expired Period: Forever DATASHEET SIR67-21C/TR8 Electro-Optical Characteristics (Ta=25℃) Parameter Radiant Intensity Symbol Ie Min. Typ. Max. 0.5 1.1 --- --- 4.5 --- Unit mW /sr Condition IF=20mA IF=100mA Pulse Width≦100μs ,Duty≦1% Peak Wavelength λp -- 875 -- nm IF=100mA Spectral Bandwidth Δλ -- 80 -- nm IF=100mA -- 1.3 1.6 -- 1.4 1.8 IR -- -- 10 μA VR=5V 2θ1/2 -- 120 -- deg IF=20mA Forward Voltage Reverse Current View Angle 3 Copyright Revision :1 © LifecyclePhase: VF V IF=20mA IF=100mA Pulse Width≦100μs ,Duty≦1% Date:2013-06-03 15:22:49.0 2010, Everlight All Rights Reserved. Release Date : MAY.20.2013. Issue Release No: DIR-0000957 www.everlight.com Expired Period: Forever DATASHEET SIR67-21C/TR8 Typical Electrical/Optical/Characteristics Curves for IR Spectral Distribution Power Dissipation vs. Ambient Temperature 140 100 120 80 IF=20mA Ta=25° C 100 60 80 60 40 40 20 20 0 -25 0 20 40 60 80 Forward Current vs. Forward Voltage 810 835 855 875 905 925 945 965 985 Relative Intensity vs. Forward Current 4 100 Ie-Radiant Intensity(mW/sr) 10 0 100 3 10 2 10 1 10 0 1 2 3 4 5 6 7 8 10 1 0 10 0 10 1 2 10 10 3 10 4 IF-Forward Current (mA) 4 Copyright Revision :1 © LifecyclePhase: Date:2013-06-03 15:22:49.0 2010, Everlight All Rights Reserved. Release Date : MAY.20.2013. Issue Release No: DIR-0000957 www.everlight.com Expired Period: Forever DATASHEET SIR67-21C/TR8 Relative Radiant Intensity vs. Angular Displacement -20 -10 0 10 Forward Voltage vs Ambient Temperature(°C) 1.4 20 30 1.3 1.0 40 0.9 50 0.8 0.7 60 70 80 0.6 0.4 0.2 0 5 Copyright Revision :1 © LifecyclePhase: IF=20mA 1.2 1.1 25 50 75 100 120 0.2 0.4 0.6 Date:2013-06-03 15:22:49.0 2010, Everlight All Rights Reserved. Release Date : MAY.20.2013. Issue Release No: DIR-0000957 www.everlight.com Expired Period: Forever DATASHEET SIR67-21C/TR8 Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 6 Copyright Revision :1 © LifecyclePhase: Date:2013-06-03 15:22:49.0 2010, Everlight All Rights Reserved. Release Date : MAY.20.2013. Issue Release No: DIR-0000957 www.everlight.com Expired Period: Forever DATASHEET SIR67-21C/TR8 4. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5. Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. 7 Copyright Revision :1 © LifecyclePhase: Date:2013-06-03 15:22:49.0 2010, Everlight All Rights Reserved. Release Date : MAY.20.2013. Issue Release No: DIR-0000957 www.everlight.com Expired Period: Forever DATASHEET SIR67-21C/TR8 Package Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm 2. Carrier Tape Dimensions:(Quantity: 2000pcs/reel) Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm 8 Copyright Revision :1 © LifecyclePhase: Date:2013-06-03 15:22:49.0 2010, Everlight All Rights Reserved. Release Date : MAY.20.2013. Issue Release No: DIR-0000957 www.everlight.com Expired Period: Forever DATASHEET SIR67-21C/TR8 Packing Procedure Aluminum moistue-proof bag Label Desiccant Label Label Form Specification Pb EVERLIGHT CPN : P N : XXXXXXXXXXXXX RoHS XXXXXXXXXXXXX CAT : XXX HUE : XXX REF : XXX QTY : XXX LOT NO : XXXXXXXXXX Reference : XXXXXXXX CPN: Customer’s Production Number P/N : Production Number QTY: Packing Quantity CAT: Ranks HUE: Peak Wavelength REF: Reference LOT No: Lot Number MADE IN TAIWAN: Production Place Notes 1. Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above specification. 2. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. 3. These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please don’t reproduce or cause anyone to reproduce them without EVERLIGHT’s consent. EVERLIGHT ELECTRONICS CO., LTD. Office: No 6-8, Zhonghua Rd., Shulin Dist., New Taipei City 23860, Taiwan, R.O.C 9 Copyright Revision :1 © LifecyclePhase: Tel: 886-2-2685-6688 Fax: 886-2-2685-6699 http://www.everlight.com Date:2013-06-03 15:22:49.0 2010, Everlight All Rights Reserved. Release Date : MAY.20.2013. Issue Release No: DIR-0000957 www.everlight.com Expired Period: Forever