HIR11-21C/L11/TR8

1206 Package Chip Infrared LED With Inner Lens
HIR11-21C/L11/TR8
Features
․High reliability
․Small double-end package
․Peak wavelength λp=850nm
․Package in 8mm tape on 7” diameter reel
․Low forward voltage
․Pb free
․The product itself will remain within RoHS compliant version.
Descriptions
HIR11-21C/L11/TR8 is an infrared emitting diode in miniature
SMD package which is molded in a water clear plastic
With flat top view lens.
The device is spectrally matched with silicon photodiode
and phototransistor.
Applications
․PCB mounted infrared sensor
․Infrared remote control units with high power requirement
․Smoke detector
․Infrared applied system
Device Selection Guide
1
Part Category
Chip
Material
Resin Color
HIR
GaAlAs
Water Clear
Copyright © 2013, Everlight All Rights Reserved. Release Date : 5/28/2013. Issue No: DIR-0000947. Rev:3
Revision
:3
LifecyclePhase:
www.everlight.com
Release Date:2013-06-04 12:13:29.0
Expired Period: Forever
Data Sheet
1206 Package Chip Infrared LED With Inner Lens
HIR11-21C/L11/TR8
Package Dimensions
Notes: 1.All dimensions are in millimeters
2.Tolerances unless dimensions ±0.1mm
Absolute Maximum Ratings (Ta=25℃)
Parameter
Symbol
Rating
Continuous Forward Current
IF
65
Units
mA
Reverse Voltage
VR
5
V
Operating Temperature
Topr
-25 ~ +85
℃
Storage Temperature
Tstg
-40 ~ +85
℃
Tsol
260
℃
Pd
130
mW
Soldering Temperature
*1
Power Dissipation at(or below)
25℃Free Air Temperature
Notes: *1. Soldering time≦5 seconds.
2
Copyright © 2013, Everlight All Rights Reserved. Release Date : 5/28/2013. Issue No: DIR-0000947. Rev:3
Revision
:3
LifecyclePhase:
www.everlight.com
Release Date:2013-06-04 12:13:29.0
Expired Period: Forever
Data Sheet
1206 Package Chip Infrared LED With Inner Lens
HIR11-21C/L11/TR8
Electro-Optical Characteristics (Ta=25℃)
Parameter
Condition
IF=20mA
Min.
Typ.
Max.
1.0
2.0
--
Radiant Intensity
Ie
. IF=100mA
Pulse Width≦100μs ,Duty≦1%
--
10
--
Peak Wavelength
λp
IF=20mA
--
850
--
nm
Spectral
Bandwidth
Δλ
IF=50mA
--
45
--
nm
IF=20mA
--
1.45
1.65
Forward Voltage
VF
. IF=100mA
Pulse Width≦100μs ,Duty≦1%
--
1.80
2.40
Reverse Current
IR
2θ1/2
VR=5V
--
--
10
IF=20mA
--
75
--
View Angle
3
Symbol
Copyright © 2013, Everlight All Rights Reserved. Release Date : 5/28/2013. Issue No: DIR-0000947. Rev:3
Revision
:3
LifecyclePhase:
Units
mW /sr
V
μA
deg
www.everlight.com
Release Date:2013-06-04 12:13:29.0
Expired Period: Forever
Data Sheet
1206 Package Chip Infrared LED With Inner Lens
HIR11-21C/L11/TR8
Typical Electro-Optical Characteristics Curves
Fig.1 Forward Current vs.
Ambient Temperature
Fig.2 Spectral Distributio n
140
100
120
IF=20mA
Ta=25° C
80
100
60
80
60
40
40
20
20
0
0
-25
0
20
40
Fig.3 Forward Current
vs. Forward Voltage
4
60
80
100
790 810 830 850 870 890 910 930 950
Fig.4 Relative Intensity vs.
Forward Current
Copyright © 2013, Everlight All Rights Reserved. Release Date : 5/28/2013. Issue No: DIR-0000947. Rev:3
Revision
:3
LifecyclePhase:
www.everlight.com
Release Date:2013-06-04 12:13:29.0
Expired Period: Forever
Data Sheet
1206 Package Chip Infrared LED With Inner Lens
HIR11-21C/L11/TR8
Typical Electro-Optical Characteristics Curves
Fig.5 Relative Radiant Intensity vs.
Angular Displacement
-20
-10
0
10
20
30
1.0
40
0.9
50
0.8
0.7
60
70
80
0.6 0.4 0.2 0
5
0.2 0.4 0.6
Copyright © 2013, Everlight All Rights Reserved. Release Date : 5/28/2013. Issue No: DIR-0000947. Rev:3
Revision
:3
LifecyclePhase:
www.everlight.com
Release Date:2013-06-04 12:13:29.0
Expired Period: Forever
Data Sheet
1206 Package Chip Infrared LED With Inner Lens
HIR11-21C/L11/TR8
Precautions For Use
1. Over-current-proof
Customer must apply resistors for protection , otherwise slight voltage shift will cause big
current change ( Burn out will happen ).
2. Storage
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less.
2.3 The LEDs should be used within a year.
2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less.
2.5 The LEDs should be used within 168 hours (7 days) after opening the package.
2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the
storage time, baking treatment should be performed using the following conditions.
Baking treatment : 60±5℃ for 24 hours.
3. Soldering Condition
3.1 Pb-free solder temperature profile
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
6
Copyright © 2013, Everlight All Rights Reserved. Release Date : 5/28/2013. Issue No: DIR-0000947. Rev:3
Revision
:3
LifecyclePhase:
www.everlight.com
Release Date:2013-06-04 12:13:29.0
Expired Period: Forever
Data Sheet
1206 Package Chip Infrared LED With Inner Lens
HIR11-21C/L11/TR8
4.Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than350℃ for 3
seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more
intervals, and do soldering of each terminal. Be careful because the damage of the product is often
started at the time of the hand solder.
5.Repairing
Repair should not be done after the LEDs have been soldered. When repairing is
unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed
beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.
7
Copyright © 2013, Everlight All Rights Reserved. Release Date : 5/28/2013. Issue No: DIR-0000947. Rev:3
Revision
:3
LifecyclePhase:
www.everlight.com
Release Date:2013-06-04 12:13:29.0
Expired Period: Forever
Data Sheet
1206 Package Chip Infrared LED With Inner Lens
HIR11-21C/L11/TR8
Package Dimensions
Note: The tolerances unless mentioned are ±0.1, unit=mm.
Carrier Taping Dimensions: Loaded Quantity Per Reel 2000PCS/Reel
Note: The tolerances unless mentioned is ±0.1mm, Unit = mm
8
Copyright © 2013, Everlight All Rights Reserved. Release Date : 5/28/2013. Issue No: DIR-0000947. Rev:3
Revision
:3
LifecyclePhase:
www.everlight.com
Release Date:2013-06-04 12:13:29.0
Expired Period: Forever
Data Sheet
1206 Package Chip Infrared LED With Inner Lens
HIR11-21C/L11/TR8
Label Form Specification
CPN: Customer’s Production Number
P/N : Production Number
QTY: Packing Quantity
CAT: Ranks
HUE: Peak Wavelength
REF: Reference
LOT No: Lot Number
Notes
1. Above specification may be changed without notice. EVERLIGHT will reserve authority on
material change for above specification.
2. When using this product, please observe the absolute maximum ratings and the instructions
for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for
any damage resulting from use of the product which does not comply with the absolute
maximum ratings and the instructions included in these specification sheets.
3. These specification sheets include materials protected under copyright of EVERLIGHT
corporation. Please don’t reproduce or cause anyone to reproduce them without EVERLIGHT’s
consent.
EVERLIGHT ELECTRONICS CO., LTD.
Office: No. 6-8, Zhonghua Rd., Shulin Dist.,
New Taipei City 23860, Taiwan
9
Tel: 886-2-2685-6688
Fax: 886-2685-2699,6897
http://www.everlight.com
Copyright © 2013, Everlight All Rights Reserved. Release Date : 5/28/2013. Issue No: DIR-0000947. Rev:3
Revision
:3
LifecyclePhase:
www.everlight.com
Release Date:2013-06-04 12:13:29.0
Expired Period: Forever