bi441 short form 2007 dev.qxd 6/26/07 8:59 AM Page 13 Fixed Resistors 13 Thick Film Resistor Networks Surface Mount 627T/V Through-Hole High Voltage Precision Divider, High Voltage L/M/BH BHV 2/3 Model 627/628 628 Ladder Number of Leads 14/16 16 14 4 to 14 Body Length, Maximum 0.395/0.445 0.445 0.395 0.1 x no. of leads 0.953 to 2.35 Height Off Board, Maximum 0.090 0.090 0.090 0.195 0.4 to 0.606 Body Style/Width (Thickness) (SO-M) 0.220 (SO-M) 0.220 (SO-M) 0.220 0.095 0.100 Range, Ohms 10 to 1 Meg 1K to 100K 50 to 142 22 to 1 Meg 1 Giga, Max. Tolerance (%) ±2 (±5 for J Circuits) ±2 ±2 ±2 (±1 Optional) ±1, ±5, ±10 Operating Temperature Range ˚C -55/125 -55/125 -55/125 Temp. Coefficient, ppm/°C ±100 (Below 100R, 250) ±100 ±250 ±100 (< 100W = ±250) ±150 (±100 Divider) Temp. Coefficient Tracking, ppm/°C ±50 ±50 ±50 ±50 0.125 Bussed 0.200 Isolated 0.8 to 3.0 Dimensions, Inches Resistance Ladder Accuracy 8 Bit: 1/2 LSB Power Rating, Watts at 70˚C Resistor Power Schematic A: 0.32 Schematics B & J: 0.16 0.04 0.250 Package Power 1.28 0.64 W/Pkg. 1.28 Operating Voltage 30kV (2kV for Precision Divider) Voltage Coefficient (ppm/V) 2 Max Packaging Options Tubes 50 50 50 2000 2000 2000 Tape & Reel: 7" Tape & Reel: 13" Specification subject to change without notice. Contact factory for custom products Also available: 627/628 Jumpers Schematics Ordering Information 62 8 N J 330 / 470 F TR4 BHV 10 Tape & Reel Opt.: Model Series 4 = 24mm RS D Tolerance Code (If other than standard): F = ±1% J = ±5% Circuit Type: A = Isolated B = Bussed J = Dual Terminator L = Ladder R2 Resistance Code: Add for J Circuit only Resistance Code 62 Model Series 7 Voltage Rating in KV Style RS = Polymer Coated with Solder pads RW = Epoxyed Coated with round wire RF = Epoxy Coated with flat leads PF = Polymer Coated with flat leads PW = Polymer Coated with round wire Absolute tolerance code F = ±1% G = ±2% J = ±5% K = ±10% R1 1 2 3 4 = 24mm Model Series 1 2 N/2 1 2 3 12 R R R 2R 1 N/2 11 11 10 1.15K 1.35K 800 83 R1 R2 R3 R4 1 9 8 6 V5 7 50 50 10 50 9 50 8 50 125 125 125 125 125 125 50 627V100 4 = 24mm R 100M 50 12 R 627T 13 14 13 R Dual Terminators BHV 14 Tape & Reel Opt.: 3 Bussed 10M 627V100 Tape & Reel Opt.: N/2 Isolated For dividers only XXX / YYY Where XXX = R1 + R2 YYY = R2 (lower value) 627 V100 TR4 R 2R 2R 2R 2R 2R 2R 2R 2R R2 Resistance Code First 2 Digits are significant last digit denotes No of trailing zeros D = Dividers only T 500 / 1250 TR4 16 N Ratio tolerance code (Dividers only) F = ±1% G = ±2% Model Series 627T 628 Ladder N XXX J F Number of Leads: 7 = 14 Leads 8 = 16 Leads 627/628 BHV 627/628/628 Ladder 50 50 2 3 50 4 50 5 50 6 7 142 R5 Number of Leads: 7 = 14 Leads Circuit Type: T = V.35 Termination Resistance Values Circuit Type: 1 GND 2 V1 3 V2 4 V3 5 V4 V100 = Pentium® Resistor Network www.bitechnologies.com