Advanced Power Electronics Corp. APE1117L 1A LOW DROPOUT LINEAR REGULATOR FEATURES DESCRIPTION 1.5V Maximum Dropout at Full Load Current Fast Transient Response Output Current Limiting Built-in Thermal Shutdown Good Noise Rejection Low-ESR Ceramic Capacitor (MLCC) Required for Stability. 3-Terminal Adjustable or Fixed 1.2V, 1.5V, APE1117L is a low dropout positive adjustable or fixedmode regulator with minimum of 1A output current capability. The product is specifically designed to provide well-regulated supply for low voltage IC applications such as high-speed bus termination and low current 3.3V logic supply. APE1117L is also well suited for other applications such as VGA cards. APE1117L is guaranteed to have lower than 1.4V dropout at full load current making it ideal to provide well-regulated outputs of 1.25 to 5.0 with 6.4V to 12V input supply. 1.8V, 2.5V, 3.3V, 5.0V Packages : SOT-223, TO-252, SOT-89. Halogen Free Product TYPICAL APPLICATION (1) Using Multilayer Ceramic Capacitor (MLCC) Fixed Output ADJ Output VOUT=3.3V VIN=5V VIN=5V VOUT=3.3V U1 U1 VIN VOUT VIN VOUT R1 GND C1 10uF APE1117L-33 240 ADJ C2 C1 10uF 10uF C2 10uF APE1117L-ADJ R2 390 VOUT = VREF × (1 + R2 );VREF = 1.250V R1 (2) Using Aluminum Electrolytic Capacitor (AL) Fixed Output ADJ Output VIN=5V VOUT=3.3V VIN=5V VIN VOUT=3.3V U1 U1 VOUT VIN VOUT R1 GND C1 10uF APE1117L-33 C2 C3 0.1uF 10uF C1 10uF 240 ADJ APE1117L-ADJ VOUT = VREF × (1 + Data and specifications subject to change without notice C2 0.1uF C3 10uF R2 390 R2 );VREF = 1.250V R1 1 201301047 Advanced Power Electronics Corp. APE1117L ABSOLUTE MAXIMUM RATINGS (at TA=25°C) DC Supply Voltage(VIN) ---------------------------------- -0.3V to 15V Power Dissipation(PD) ------------------------------------ (TJ-TA)/Rthja W Storage Temperature Range(T ST) --------------------- -65°C To 150°C Operating Junction Temperature Range(T J) -------- -40°C To 125°C Maximum Junction Temperature(T MJ) ---------------- 150°C Thermal Resistance from Junction to Case(R thjc) SOT-223 ------ 15°C/W SOT-89 -------- 100°C/W TO-252 -------- 10°C/W Thermal Resistance from Junction to Ambient(R thja)Note SOT-223 ------ 117°C/W SOT-89 -------- 300°C/W TO-252 -------- 92°C/W Note. No heat sink; No air flow) ORDERING/PACKAGE INFORMATION APE1117LX - XX Package Type K : SOT-223 G : SOT-89 H : TO-252 (Top View) Tab is VOUT (Top View) Tab is VOUT SOT-223 SOT-89 (G) (Top View) Tab is VOUT Output Voltage Blank : ADJ 12 : 1.2V 15 : 1.5V 18 : 1.8V 25 : 2.5V 33 : 3.3V 50 : 5.0V 1 2 3 1 2 TO-252 3 1 ADJ/ GND VOUT VIN ADJ/ GND VOUT VIN 2 3 VOUT ADJ/ GND VIN ELECTRICAL SPECIFICATIONS (TA=25°C, unless otherwise specified) Parameter Operation Input Voltage TEST CONDITION Minimum Load Current APE1117LXADJ/12/15/18 IOUT = 1A , δVOUT=1%VOUT /25/33/50 APE1117LXADJ/15/18/25 (VIN-VOUT) = 3V /33/50 APE1117LX-XX 0°C≦TJ≦125°C Line Regulation APE1117LX-XX Dropout Voltage(VIN-VOUT) Current Limit IOUT=10mA, VOUT+1.5V<VIN<VOUT<12V, TJ=25°C (Note 1,2) MIN 2.75 TYP - MAX 12 UNITS - 1.3 1.5 V 1.1 - - A - 5 10 mA - 0.2 0.5 % V 2 Advanced Power Electronics Corp. APE1117L ELECTRICAL SPECIFICATIONS(Cont.) Parameter APE1117LX-ADJ APE1117LX-12 APE1117LX-15 Load Regulation APE1117LX-18 APE1117LX-25 APE1117LX-33 APE1117LX-50 Reference Voltage APE1117LX-ADJ IOUT = 10mA, TJ=25°C, (VIN-VOUT)=1.5V APE1117LX-12 APE1117LX-15 APE1117LX-18 Output Voltage APE1117LX-25 APE1117LX-33 APE1117LX-50 Ripple Rejection Temperature Stability TEST CONDITION VIN=3.3V,10mA≦IOUT≦1A, TJ=25°C VIN=2.75V, 10mA ≦ IOUT ≦ 1A, TJ=25°C (Note 1,2) VIN=3V, 10mA≦IOUT≦1A, TJ=25°C (Note 1,2) VIN=3.3V, 0mA≦IOUT ≦ 1A, TJ=25° C (Note 1,2) VIN=4V, 10mA≦IOUT≦1A, TJ=25°C (Note 1,2) VIN=5V,10mA≦IOUT ≦1A, TJ=25°C (Note 1,2) VIN=6.5V,10mA≦IOUT ≦1A, TJ=25° C (Note 1,2) IOUT=10mA, TJ = 25°C, 2.75V≦VIN ≦12V IOUT = 10mA, TJ = 25°C, 3V≦VIN≦ 12V IOUT = 10mA, TJ = 25°C, 3.3V≦VIN ≦12V IOUT = 10mA, TJ = 25°C, 4V≦VIN≦ 12V IOUT = 10mA, TJ = 25°C, 4.8V≦VIN ≦12V IOUT = 10mA, TJ = 25°C, 6.5V≦VIN ≦12V F=120Hz,COUT=10uF, APE1117LXXX, (VIN-VOUT) = 3V, IOUT = 1A IOUT=10mA MIN - TYP 0.4 MAX 1 UNITS - 10 12 mV - 12 15 mV - 15 18 mV - 20 25 mV - 26 33 mV - 40 50 mV 1.225 1.25 1.275 V 1.176 1.2 1.224 V 1.47 1.5 1.53 V 1.764 1.8 1.836 V 2.45 2.5 2.55 V 3.235 3.3 3.365 V 4.9 5 5.1 V - 60 70 dB - 0.5 - % % Note1: See thermal regulation specifications for changes in output voltage due to heating effects. Line and load regulation are measured at a constant junction temperature by low duty cycle pulse testing. Load regulation is measured at the output lead = 1/18” from the package. Note2: Line and load regulation are guaranteed up to the maximum power dissipation of 15W. Power dissipation is determined by the difference between input and output differential and the output current. Guaranteed maximum power dissipation will not be available over the full input/output range. Note3: Quiescent current is defined as the minimum output current required in maintaining regulation. At 12V input/output differential the device is guaranteed to regulate if the output current is greater than 10mA. 3 Advanced Power Electronics Corp. APE1117L PIN DESCRIPTIONS PIN SYMBOL ADJ/GND PIN DESCRIPTION A resistor divider from this pin to the V OUT pin and ground sets the output voltage. (Ground only for Fixed-Mode) VOUT The output of the regulator. (Note1,2) The input pin of regulator. Typically a large storage capacitor is connected from this pin to ground to insure that the input voltage does not sag below the minimum VIN dropout voltage during the load transient response. This pin must always be 1.5V higher than VOUT in order for the device to regulate properly. (Note1) Note1: To prevent oscillation, a 4.7uF minimum X7R or X5R dielectric is strongly recommended if ceramics are used as output capacitors. Note2: A minimum of 4.7uF EL capacitor to 100uF must be connected from this pin to ground to insure stability. BLOCK DIAGRAM Vin 3 2 Vout + + - 1.25V CURRENT LIMIT 1 + Thermal Shutdown + - GND (FIXED) 1 Adj 4 Advanced Power Electronics Corp. APE1117L TYPICAL PERFORMANCE CHARACTERISTICS 0.20 1.6 1.4 Output Voltage Deviation (%) Tj=25℃ Dropout Voltage (V) 1.2 1 0.8 0.6 Tj= 125℃ 0.4 0.2 0 0.4 0.2 0 0.8 0.6 0 I load=800mA -0.20 -0.40 -0.80 1 -1 Output Current (A) -25 Dropout Voltage vs Output Current 25 0 50 75 100 125 Temperature (℃) Load Regulation vs Temperature 2 1 1.5 Output Voltage Deviation (%) Output Voltage Change (%) 0.8 1 0. 5 0 -0.5 -1 -1.5 -2 -50 -25 0 25 50 75 100 125 150 0.6 0.4 0.2 0 Temperature (℃) 2 4 6.5 Cin=1uF Cout= 10 uF Tantalum 5.5 40 20 0 -20 -40 0 20 40 60 80 100 120 140 160 180 200 TIME (us) Line Transient Response 8 10 12 Line Regulation Load Current (A) Output Voltage Deviation ( mV) Output VoltageDeviation (mV) Input Voltage (V) 7.5 6 Input Voltage (V) Percent Change in Output Voltage vs Temperature 30 C in =1uF C out= 10 uF Tantalum Preload= 100mA 20 10 0 - 10 - 20 2 1 0 -1 0 10 20 30 40 50 60 70 80 90 100 TIME (us) Load Transient Response 5 Advanced Power Electronics Corp. APE1117L MARKING INFORMATION SOT-223 Part Number : XXXXXX YWWSSS Part Number Marking APE1117LK 1117L APE1117LK-12 117L-12 APE1117LK-15 117L-15 APE1117LK-18 117L-18 APE1117LK-25 117L-25 APE1117LK-33 117L-33 APE1117LK-50 117L-50 Date Code (YWWSSS) Y:Year WW:Week SSS:Sequence SOT-89 Part Number Identification code : 17LX YWWS Date Code (YWWS) Y:Year WW:Week S:Sequence Part Number Identification code APE1117LG A APE1117LG-12 H APE1117LG-15 B APE1117LG-18 C APE1117LG-25 D APE1117LG-33 E APE1117LG-50 F TO-252 Part Number : XXXXXX Logo YWWSSS Part Number Marking APE1117LH 1117L APE1117LH-12 1117L-12 APE1117LH-15 1117L-15 APE1117LH-18 1117L-18 APE1117LH-25 1117L-25 APE1117LH-33 1117L-33 APE1117LH-50 1117L-50 Date Code (YWWSSS) Y:Last Digit Of The Year WW:Week SSS:Sequence 6