S29JL032J - Spansion

S29JL032J
32 Megabit (4M x 8-Bit/2M x 16-Bit)
CMOS 3.0 Volt-Only, Simultaneous Read/Write
Flash Memory
S29JL032J Cover Sheet
Data Sheet
Notice to Readers: This document states the current technical specifications regarding the Spansion
product(s) described herein. Each product described herein may be designated as Advance Information,
Preliminary, or Full Production. See Notice On Data Sheet Designations for definitions.
Publication Number S29JL032J_00
Revision 06
Issue Date December 16, 2011
D a t a
S h e e t
Notice On Data Sheet Designations
Spansion Inc. issues data sheets with Advance Information or Preliminary designations to advise readers of
product information or intended specifications throughout the product life cycle, including development,
qualification, initial production, and full production. In all cases, however, readers are encouraged to verify
that they have the latest information before finalizing their design. The following descriptions of Spansion data
sheet designations are presented here to highlight their presence and definitions.
Advance Information
The Advance Information designation indicates that Spansion Inc. is developing one or more specific
products, but has not committed any design to production. Information presented in a document with this
designation is likely to change, and in some cases, development on the product may discontinue. Spansion
Inc. therefore places the following conditions upon Advance Information content:
“This document contains information on one or more products under development at Spansion Inc.
The information is intended to help you evaluate this product. Do not design in this product without
contacting the factory. Spansion Inc. reserves the right to change or discontinue work on this proposed
product without notice.”
Preliminary
The Preliminary designation indicates that the product development has progressed such that a commitment
to production has taken place. This designation covers several aspects of the product life cycle, including
product qualification, initial production, and the subsequent phases in the manufacturing process that occur
before full production is achieved. Changes to the technical specifications presented in a Preliminary
document should be expected while keeping these aspects of production under consideration. Spansion
places the following conditions upon Preliminary content:
“This document states the current technical specifications regarding the Spansion product(s)
described herein. The Preliminary status of this document indicates that product qualification has been
completed, and that initial production has begun. Due to the phases of the manufacturing process that
require maintaining efficiency and quality, this document may be revised by subsequent versions or
modifications due to changes in technical specifications.”
Combination
Some data sheets contain a combination of products with different designations (Advance Information,
Preliminary, or Full Production). This type of document distinguishes these products and their designations
wherever necessary, typically on the first page, the ordering information page, and pages with the DC
Characteristics table and the AC Erase and Program table (in the table notes). The disclaimer on the first
page refers the reader to the notice on this page.
Full Production (No Designation on Document)
When a product has been in production for a period of time such that no changes or only nominal changes
are expected, the Preliminary designation is removed from the data sheet. Nominal changes may include
those affecting the number of ordering part numbers available, such as the addition or deletion of a speed
option, temperature range, package type, or VIO range. Changes may also include those needed to clarify a
description or to correct a typographical error or incorrect specification. Spansion Inc. applies the following
conditions to documents in this category:
“This document states the current technical specifications regarding the Spansion product(s)
described herein. Spansion Inc. deems the products to have been in sufficient production volume such
that subsequent versions of this document are not expected to change. However, typographical or
specification corrections, or modifications to the valid combinations offered may occur.”
Questions regarding these document designations may be directed to your local sales office.
2
S29JL032J
S29JL032J_00_06 December 16, 2011
S29JL032J
32 Megabit (4M x 8-Bit/2M x 16-Bit)
CMOS 3.0 Volt-Only, Simultaneous Read/Write
Flash Memory
Data Sheet
Distinctive Characteristics
 Ultra low power consumption (typical values)
Architectural Advantages
– 2 mA active read current at 1 MHz
– 10 mA active read current at 5 MHz
– 200 nA in standby or automatic sleep mode
 Simultaneous Read/Write operations
– Data can be continuously read from one bank while executing
erase/program functions in another bank.
– Zero latency between read and write operations
 Cycling endurance: 1 million cycles per sector typical
 Data retention: 20 years typical
 Multiple bank architecture
– Four bank architectures available (refer to Table 8.2 on page 17).
Software Features
 Boot sectors
 Supports Common Flash Memory Interface (CFI)
– Top or bottom boot sector configurations available
– Any combination of sectors can be erased
 Erase suspend/Erase resume
 Manufactured on 0.11 µm Process Technology
– Suspends erase operations to read data from, or program data to, a
sector that is not being erased, then resumes the erase operation.
 Secured Silicon Region: Extra 256 byte sector
 Data# polling and toggle bits
– Factory locked and identifiable: 16 bytes available for secure,
random factory Electronic Serial Number; verifiable as factory
locked through autoselect function
– Customer lockable: One-time programmable only. Once locked,
data cannot be changed
– Provides a software method of detecting the status of program or
erase operations
 Unlock bypass program command
– Reduces overall programming time when issuing multiple program
command sequences
 Zero power operation
– Sophisticated power management circuits reduce power consumed
during inactive periods to nearly zero.
 Compatible with JEDEC standards
– Pinout and software compatible with single-power-supply flash
standard
Package Options
 48-ball Fine-pitch BGA
 48-pin TSOP
Performance Characteristics
Hardware Features
 Ready/Busy# output (RY/BY#)
– Hardware method for detecting program or erase cycle completion
 Hardware reset pin (RESET#)
– Hardware method of resetting the internal state machine to the read
mode
 WP#/ACC input pin
– Write protect (WP#) function protects the two outermost boot
sectors regardless of sector protect status
– Acceleration (ACC) function accelerates program timing
 Sector protection
 High performance
– Access time as fast as 60 ns
– Program time: 6 µs/word typical using accelerated programming
function
– Hardware method to prevent any program or erase operation within
a sector
– Temporary Sector Unprotect allows changing data in protected
sectors in-system
General Description
The S29JL032J is a 32 Mbit, 3.0 volt-only flash memory device, organized as 2,097,152 words of 16 bits each or 4,194,304
bytes of 8 bits each. Word mode data appears on DQ15–DQ0; byte mode data appears on DQ7–DQ0. The device is designed
to be programmed in-system with the standard 3.0 volt VCC supply, and can also be programmed in standard EPROM
programmers. The device is available with an access time of 60, or 70 ns and is offered in a 48-ball FBGA or a 48-pin TSOP
package. Standard control pins—chip enable (CE#), write enable (WE#), and output enable (OE#)—control normal read and
write operations, and avoid bus contention issues. The device requires only a single 3.0 volt power supply for both read and
write functions. Internally generated and regulated voltages are provided for the program and erase operations.
Publication Number S29JL032J_00
Revision 06
Issue Date December 16, 2011
D a t a
S h e e t
Table of Contents
Distinctive Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
4
1.
Simultaneous Read/Write Operations with Zero Latency. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.1
S29JL032J Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.
Product Selector Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.1
4-Bank Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.2
2-Bank Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.
Connection Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.1
48-pin TSOP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.2
48-ball FBGA Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.
Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
6.
Logic Symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
7.
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
8.
Device Bus Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.1
Word/Byte Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2
Requirements for Reading Array Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.3
Writing Commands/Command Sequences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.4
Simultaneous Read/Write Operations with Zero Latency . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.5
Standby Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.6
Automatic Sleep Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.7
RESET#: Hardware Reset Pin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.8
Output Disable Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.9
Autoselect Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.10 Boot Sector/Sector Block Protection and Unprotection . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.11 Write Protect (WP#) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.12 Temporary Sector Unprotect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.13 Secured Silicon Region . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.14 Hardware Data Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.
Common Flash Memory Interface (CFI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
10.
Command Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.1 Reading Array Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.2 Reset Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.3 Autoselect Command Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.4 Enter Secured Silicon Region/Exit Secured Silicon Region Command Sequence . . . . . . . .
10.5 Byte/Word Program Command Sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.6 Chip Erase Command Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.7 Sector Erase Command Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.8 Erase Suspend/Erase Resume Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
32
32
32
33
33
33
35
35
37
11.
Write Operation Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.1 DQ7: Data# Polling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.2 RY/BY#: Ready/Busy#. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.3 DQ6: Toggle Bit I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.4 DQ2: Toggle Bit II . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.5 Reading Toggle Bits DQ6/DQ2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.6 DQ5: Exceeded Timing Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.7 DQ3: Sector Erase Timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
39
39
40
40
42
42
42
43
12.
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
13.
Operating Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
14.
DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
14.1 CMOS Compatible . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
S29JL032J
14
14
15
15
16
16
16
16
17
22
23
25
25
27
28
S29JL032J_00_06 December 16, 2011
D a t a
14.2
S h e e t
Zero-Power Flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
15.
Test Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
16.
Key To Switching Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
17.
AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17.1 Read-Only Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17.2 Hardware Reset (RESET#) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17.3 Word/Byte Configuration (BYTE#) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17.4 Erase and Program Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17.5 Temporary Sector Unprotect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17.6 Alternate CE# Controlled Erase and Program Operations . . . . . . . . . . . . . . . . . . . . . . . . . .
18.
Erase and Programming Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
19.
Pin Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
20.
Physical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
20.1 TS 048—48-Pin Standard TSOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
20.2 VBK048—48-Pin FBGA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
21.
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
December 16, 2011 S29JL032J_00_06
S29JL032J
48
48
49
50
51
55
56
5
D a t a
S h e e t
Figures
Figure 8.1
Figure 8.2
Figure 8.3
Figure 10.1
Figure 10.2
Figure 11.1
Figure 11.2
Figure 12.1
Figure 12.2
Figure 14.1
Figure 14.2
Figure 15.1
Figure 16.1
Figure 17.1
Figure 17.2
Figure 17.3
Figure 17.4
Figure 17.5
Figure 17.6
Figure 17.7
Figure 17.8
Figure 17.9
Figure 17.10
Figure 17.11
Figure 17.12
Figure 17.13
Figure 17.14
6
Temporary Sector Unprotect Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
In-System Sector Protect/Unprotect Algorithms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Secured Silicon Region Protect Verify . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Program Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Erase Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Data# Polling Algorithm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Toggle Bit Algorithm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum Negative Overshoot Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum Positive Overshoot Waveform. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ICC1 Current vs. Time (Showing Active and Automatic Sleep Currents) . . . . . . . . . . . . . . . .
Typical ICC1 vs. Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Test Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Waveforms and Measurement Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Read Operation Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reset Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BYTE# Timings for Read Operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BYTE# Timings for Write Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Program Operation Timings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accelerated Program Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chip/Sector Erase Operation Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Back-to-back Read/Write Cycle Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Data# Polling Timings (During Embedded Algorithms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Toggle Bit Timings (During Embedded Algorithms). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DQ2 vs. DQ6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Temporary Sector Unprotect Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sector/Sector Block Protect and Unprotect Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . .
Alternate CE# Controlled Write (Erase/Program) Operation Timings . . . . . . . . . . . . . . . . . .
S29JL032J
25
26
28
34
36
40
41
44
44
46
46
47
47
48
49
50
50
52
52
53
53
54
54
55
55
56
57
S29JL032J_00_06 December 16, 2011
D a t a
S h e e t
Tables
Table 8.1
Table 8.2
Table 8.3
Table 8.4
Table 8.5
Table 8.6
Table 8.7
Table 8.8
Table 9.1
Table 9.2
Table 9.3
Table 9.4
Table 10.1
Table 11.1
Table 15.1
S29JL032J Device Bus Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S29JL032J Bank Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S29JL032J Sector Addresses - Top Boot Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S29JL032J Sector Addresses - Bottom Boot Devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S29JL032J Autoselect Codes (High Voltage Method). . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S29JL032J Boot Sector/Sector Block Addresses for
Protection/Unprotection (Top Boot Devices) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S29JL032J Sector/Sector Block Addresses for
Protection/Unprotection (Bottom Boot Devices) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WP#/ACC Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CFI Query Identification String. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Interface String . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Device Geometry Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Primary Vendor-Specific Extended Query . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S29JL032J Command Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Write Operation Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Test Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
December 16, 2011 S29JL032J_00_06
S29JL032J
14
17
18
20
22
23
24
25
29
29
30
31
38
43
47
7
D a t a
1.
S h e e t
Simultaneous Read/Write Operations with Zero Latency
The Simultaneous Read/Write architecture provides simultaneous operation by dividing the memory space
into separate banks (see Table 8.2 on page 17). Sector addresses are fixed, system software can be used to
form user-defined bank groups.
During an Erase/Program operation, any of the non-busy banks may be read from. Note that only two banks
can operate simultaneously. The device can improve overall system performance by allowing a host system
to program or erase in one bank, then immediately and simultaneously read from the other bank, with zero
latency. This releases the system from waiting for the completion of program or erase operations.
The S29JL032J can be organized with either a top or bottom boot sector configuration.
1.1
S29JL032J Features
The Secured Silicon Region is an extra 256 byte sector capable of being permanently locked by the
customer. The Secured Silicon Customer Indicator Bit (DQ6) is permanently set to 1 if the part has been
locked and is 0 if lockable.
Customers may utilize the Secured Silicon Region as bonus space, reading and writing like any other flash
sector, or may permanently lock their own code there.
The device offers complete compatibility with the JEDEC 42.4 single-power-supply Flash command set
standard. Commands are written to the command register using standard microprocessor write timings.
Reading data out of the device is similar to reading from other Flash or EPROM devices.
The host system can detect whether a program or erase operation is complete by using the device status
bits: RY/BY# pin, DQ7 (Data# Polling) and DQ6/DQ2 (toggle bits). After a program or erase cycle has been
completed, the device automatically returns to the read mode.
The sector erase architecture allows memory sectors to be erased and reprogrammed without affecting the
data contents of other sectors. The device is fully erased when shipped from the factory.
Hardware data protection measures include a low VCC detector that automatically inhibits write operations
during power transitions. The hardware sector protection feature disables both program and erase
operations in any combination of the sectors of memory. This can be achieved in-system or via programming
equipment.
The Erase Suspend/Erase Resume feature enables the user to put erase on hold for any period of time to
read data from, or program data to, any sector that is not selected for erasure. True background erase can
thus be achieved. If a read is needed from the Secured Silicon Region area (One Time Program area) after
an erase suspend, then the user must use the proper command sequence to enter and exit this region.
The device offers two power-saving features. When addresses have been stable for a specified amount of
time, the device enters the automatic sleep mode. The system can also place the device into the standby
mode. Power consumption is greatly reduced in both modes.
8
S29JL032J
S29JL032J_00_06 December 16, 2011
D a t a
2.
S h e e t
Product Selector Guide
Part Number
S29JL032J
Standard Voltage Range: VCC = 3.0–3.6V
Speed Option
60
Standard Voltage Range: VCC = 2.7–3.6V
70
Max Access Time (ns), tACC
60
70
CE# Access (ns), tCE
60
70
OE# Access (ns), tOE
25
30
3. Block Diagram
4-Bank Device
VCC
VSS
OE#
Mux
BYTE#
Bank 1
RY/BY#
Bank 2 Address
Bank 2
X-Decoder
A20–A0
RESET#
WE#
CE#
BYTE#
WP#/ACC
STATE
CONTROL
&
COMMAND
REGISTER
Status
DQ15–DQ0
Control
Mux
DQ15–DQ0
DQ0–DQ15
Bank 3
Bank 3 Address
X-Decoder
A20–A0
Bank 4 Address
Y-gate
A20–A0
X-Decoder
DQ15–DQ0
A20–A0
X-Decoder
DQ15–DQ0
A20–A0
DQ15–DQ0
Bank 1 Address
Y-gate
3.1
Bank 4
Mux
December 16, 2011 S29JL032J_00_06
S29JL032J
9
D a t a
2-Bank Device
OE# BYTE#
A20–A0
RY/BY#
X-Decoder
A20–A0
RESET#
WE#
CE#
BYTE#
WP#/ACC
Upper Bank
DQ15–DQ0
Upper Bank Address
A20–A0
Y-Decoder
VCC
VSS
Latches and Control Logic
3.2
S h e e t
STATE
CONTROL
&
COMMAND
REGISTER
Status
DQ15–DQ0
Control
Y-Decoder
Lower Bank Address
Lower Bank
Latches and
Control Logic
X-Decoder
A20–A0
A20–A0
DQ15–DQ0
DQ15–DQ0
OE# BYTE#
10
S29JL032J
S29JL032J_00_06 December 16, 2011
D a t a
S h e e t
4. Connection Diagrams
4.1
48-pin TSOP Package
A15
A14
A13
A12
A11
A10
A9
A8
A19
A20
WE#
RESET#
NC
WP#/ACC
RY/BY#
A18
A17
A7
A6
A5
A4
A3
A2
A1
4.2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
48-Pin Standard TSOP
A16
BYTE#
VSS
DQ15/A-1
DQ7
DQ14
DQ6
DQ13
DQ5
DQ12
DQ4
VCC
DQ11
DQ3
DQ10
DQ2
DQ9
DQ1
DQ8
DQ0
OE#
VSS
CE#
A0
48-ball FBGA Package
A6
B6
A14
D6
A15
E6
A16
F6
G6
BYTE# DQ15/A-1
H6
VSS
A13
A12
A5
B5
C5
D5
E5
F5
G5
H5
A9
A8
A10
A11
DQ7
DQ14
DQ13
DQ6
A4
B4
C4
D4
E4
F4
G4
H4
WE#
RESET#
NC
A19
DQ5
DQ12
VCC
DQ4
A3
B3
RY/BY# WP#/ACC
December 16, 2011 S29JL032J_00_06
C6
C3
D3
E3
F3
G3
H3
A18
A20
DQ2
DQ10
DQ11
DQ3
A2
B2
C2
D2
E2
F2
G2
H2
A7
A17
A6
A5
DQ0
DQ8
DQ9
DQ1
A1
B1
C1
D1
E1
F1
G1
H1
A3
A4
A2
A1
A0
CE#
OE#
VSS
S29JL032J
11
D a t a
5.
S h e e t
Pin Description
A20–A0
21 Address Pins
DQ14–DQ0
15 Data Inputs/Outputs (x16-only devices)
DQ15/A-1
DQ15 (Data Input/Output, word mode), A-1 (LSB Address Input, byte mode)
CE#
Chip Enable, Active Low
OE#
Output Enable, Active Low
WE#
Write Enable, Active Low
WP#/ACC
Hardware Write Protect/Acceleration Pin.
RESET#
Hardware Reset Pin, Active Low
BYTE#
Selects 8-bit or 16-bit mode, Active Low
RY/BY#
Ready/Busy Output, Active Low
VCC
3.0 volt-only single power supply (see Product Selector Guide on page 9 for
speed options and voltage supply tolerances)
VSS
Device Ground
NC
Not Connected – No device internal signal is connected to the package
connector nor is there any future plan to use the connector for a signal. The
connection may safely be used for routing space for a signal on a Printed Circuit
Board (PCB).
6. Logic Symbol
21
A20–A0
16 or 8
DQ15–DQ0
(A-1)
CE#
OE#
WE#
WP#/ACC
RESET#
RY/BY#
BYTE#
12
S29JL032J
S29JL032J_00_06 December 16, 2011
D a t a
7.
S h e e t
Ordering Information
The order number (Valid Combination) is formed by the following:
S29JL032J
60
T
F
I
01
0
Packing Type
0 = Tray
3 = 13-inch Tape and Reel
Model Number
01 = Top Boot Device, 4 Banks: 4/12/12/4 Mb
02 = Bottom Boot Device, 4 Banks: 4/12/12/4 Mb
21 = Top Boot Device, 2 Banks: 4/28 Mb
22 = Bottom Boot Device, 2 Banks: 4/28 Mb
31 = Top Boot Device, 2 Banks: 8/24 Mb
32 = Bottom Boot Device, 2 Banks: 8/24 Mb
41 = Top Boot Device, 2 Banks: 16/16 Mb
42 = Bottom Boot Device, 2 Banks: 16/16 Mb
Temperature Range
I = Industrial (–40°C to +85°C)
Package Material Set
F = Pb-free
H = Low-halogen, Pb-free
Package Type
B = Fine-pitch Ball Grid Array Package
T = Thin Small Outline Package (TSOP) Standard Pinout
Speed Option
60 = 60 ns
70 = 70 ns
Device Family
S29JL032J
3.0 Volt-only, 32 Mbit (2 M x 16-Bit/4 M x 8-Bit) Simultaneous Read/Write Flash Memory
Manufactured on 110 nm process technology
S29JL032J Valid Combinations
Device Number/
Description
Speed (ns)
S29JL032J
60, 70
Package Type
Temperature
Range
TF
Additional
Ordering Options
Packing
Type
01, 02, 21, 22, 31, 32, 41, 42
I
BH
Package
Description
TS048
TSOP
VBK048
FBGA
0, 3 (1)
31, 32
Note:
1. Type 0 is standard. Specify others as required.
Valid Combinations
Valid Combinations list configurations planned to be supported in volume for this device. Consult your local
Spansion sales office to confirm availability of specific valid combinations and to check on newly released
combinations.
December 16, 2011 S29JL032J_00_06
S29JL032J
13
D a t a
8.
S h e e t
Device Bus Operations
This section describes the requirements and use of the device bus operations, which are initiated through the
internal command register. The command register itself does not occupy any addressable memory location.
The register is a latch used to store the commands, along with the address and data information needed to
execute the command. The contents of the register serve as inputs to the internal state machine. The state
machine outputs dictate the function of the device. Table 8.1 lists the device bus operations, the inputs and
control levels they require, and the resulting output. The following subsections describe each of these
operations in further detail.
Table 8.1 S29JL032J Device Bus Operations
DQ15–DQ8
Addresses
(Note 1)
BYTE# = VIH
BYTE# = VIL
DQ7–DQ0
L/H
AIN
DOUT
(Note 3)
AIN
DIN
DQ14–DQ8 = High-Z,
DQ15 = A-1
DOUT
H
X
VCC ±
0.3V
L/H
X
High-Z
High-Z
High-Z
H
H
H
L/H
X
High-Z
High-Z
High-Z
X
X
L
L/H
X
High-Z
High-Z
High-Z
L
H
L
VID
L/H
SA, A6 = L,
A1 = H, A0 = L
X
X
DIN
Sector Unprotect
(Note 2)
L
H
L
VID
(Note 3)
SA, A6 = H,
A1 = H, A0 = L
X
X
DIN
Temporary Sector
Unprotect
X
X
X
VID
(Note 3)
AIN
DIN
High-Z
DIN
Operation
CE#
OE#
Read
L
L
H
H
Write
L
H
L
VCC ±
0.3V
X
Output Disable
L
Reset
X
Standby
Sector Protect
(Note 2)
WE# RESET# WP#/ACC
DIN
Legend:
L = Logic Low = VIL
H = Logic High = VIH
VID = 8.5–12.5V
VHH = 9.0 ± 0.5V
X = Don’t Care
SA = Sector Address
AIN = Address In
DIN = Data In
DOUT = Data Out
Notes:
1. Addresses are A20:A0 in word mode (BYTE# = VIH), A20:A-1 in byte mode (BYTE# = VIL).
2. The sector protect and sector unprotect functions may also be implemented via programming equipment. See Boot Sector/Sector Block
Protection and Unprotection on page 23.
3. If WP#/ACC = VIL, the two outermost boot sectors remain protected. If WP#/ACC = VIH, protection on the two outermost boot sectors
depends on whether they were last protected or unprotected using the method described in Boot Sector/Sector Block Protection and
Unprotection on page 23. If WP#/ACC = VHH, all sectors will be unprotected.
8.1
Word/Byte Configuration
The BYTE# pin controls whether the device data I/O pins operate in the byte or word configuration. If the
BYTE# pin is set at logic ‘1’, the device is in word configuration, DQ15–DQ0 are active and controlled by CE#
and OE#.
If the BYTE# pin is set at logic ‘0’, the device is in byte configuration, and only data I/O pins DQ7–DQ0 are
active and controlled by CE# and OE#. The data I/O pins DQ14–DQ8 are tri-stated, and the DQ15 pin is used
as an input for the LSB (A-1) address function.
14
S29JL032J
S29JL032J_00_06 December 16, 2011
D a t a
8.2
S h e e t
Requirements for Reading Array Data
To read array data from the outputs, the system must drive the CE# and OE# pins to VIL. CE# is the power
control and selects the device. OE# is the output control and gates array data to the output pins. WE# should
remain at VIH. The BYTE# pin determines whether the device outputs array data in words or bytes.
The internal state machine is set for reading array data upon device power-up, or after a hardware reset. This
ensures that no spurious alteration of the memory content occurs during the power transition. No command is
necessary in this mode to obtain array data. Standard microprocessor read cycles that assert valid addresses
on the device address inputs produce valid data on the device data outputs. Each bank remains enabled for
read access until the command register contents are altered.
Refer to the Read-Only Operations on page 48 for timing specifications and to Figure 17.1 on page 48 for the
timing diagram. ICC1 in DC Characteristics on page 45 represents the active current specification for reading
array data.
8.3
Writing Commands/Command Sequences
To write a command or command sequence (which includes programming data to the device and erasing
sectors of memory), the system must drive WE# and CE# to VIL, and OE# to VIH.
For program operations, the BYTE# pin determines whether the device accepts program data in bytes or
words. Refer to Word/Byte Configuration on page 14 for more information.
The device features an Unlock Bypass mode to facilitate faster programming. Once a bank enters the
Unlock Bypass mode, only two write cycles are required to program a word or byte, instead of four. Byte/
Word Program Command Sequence on page 33 has details on programming data to the device using both
standard and Unlock Bypass command sequences.
An erase operation can erase one sector, multiple sectors, or the entire device. Table 8.3 on page 18 and
Table 8.4 on page 20 indicate the address space that each sector occupies. Similarly, a “sector address” is
the address bits required to uniquely select a sector. Command Definitions on page 32 has details on erasing
a sector or the entire chip, or suspending/resuming the erase operation.
The device address space is divided into four banks. A “bank address” is the address bits required to uniquely
select a bank.
ICC2 in the DC Characteristics table represents the active current specification for the write mode. AC
Characteristics on page 48 contains timing specification tables and timing diagrams for write operations.
8.3.1
Accelerated Program Operation
The device offers accelerated program operations through the ACC function. This is one of two functions
provided by the WP#/ACC pin. This function is primarily intended to allow faster manufacturing throughput at
the factory.
If the system asserts VHH on this pin, the device automatically enters the aforementioned Unlock Bypass
mode, temporarily unprotects any protected sectors, and uses the higher voltage on the pin to reduce the
time required for program operations. The system would use a two-cycle program command sequence as
required by the Unlock Bypass mode. Removing VHH from the WP#/ACC pin returns the device to normal
operation. Note that VHH must not be asserted on WP#/ACC for operations other than accelerated
programming, or device damage may result. In addition, the WP#/ACC pin must not be left floating or
unconnected; inconsistent behavior of the device may result. See Write Protect (WP#) on page 25 for related
information.
8.3.2
Autoselect Functions
If the system writes the autoselect command sequence, the device enters the autoselect mode. The system
can then read autoselect codes from the internal register (which is separate from the memory array) on
DQ15–DQ0. Standard read cycle timings apply in this mode. Refer to Autoselect Mode on page 22 and
Autoselect Command Sequence on page 33 for more information.
December 16, 2011 S29JL032J_00_06
S29JL032J
15
D a t a
8.4
S h e e t
Simultaneous Read/Write Operations with Zero Latency
This device is capable of reading data from one bank of memory while programming or erasing in another
bank of memory. An erase operation may also be suspended to read from or program to another location
within the same bank (except the sector being erased). Figure 17.8 on page 53 shows how read and write
cycles may be initiated for simultaneous operation with zero latency. ICC6 and ICC7 in DC Characteristics
on page 45 represent the current specifications for read-while-program and read-while-erase, respectively.
8.5
Standby Mode
When the system is not reading or writing to the device, it can place the device in the standby mode. In this
mode, current consumption is greatly reduced, and the outputs are placed in the high impedance state,
independent of the OE# input.
The device enters the CMOS standby mode when the CE# and RESET# pins are both held at VCC ± 0.3V.
Note that this is a more restricted voltage range than VIH. If CE# and RESET# are held at VIH, but not within
VCC ± 0.3V, the device will be in the standby mode, but the standby current will be greater. The device
requires standard access time (tCE) for read access when the device is in either of these standby modes,
before it is ready to read data.
If the device is deselected during erasure or programming, the device draws active current until the operation
is completed.
ICC3 in DC Characteristics on page 45 represents the standby current specification.
8.6
Automatic Sleep Mode
The automatic sleep mode minimizes Flash device energy consumption. The device automatically enables
this mode when addresses remain stable for tACC + 30 ns. The automatic sleep mode is independent of the
CE#, WE#, and OE# control signals. Standard address access timings provide new data when addresses are
changed. While in sleep mode, output data is latched and always available to the system. ICC5 in DC
Characteristics on page 45 represents the automatic sleep mode current specification.
8.7
RESET#: Hardware Reset Pin
The RESET# pin provides a hardware method of resetting the device to reading array data. When the
RESET# pin is driven low for at least a period of tRP, the device immediately terminates any operation in
progress, tristates all output pins, and ignores all read/write commands for the duration of the RESET# pulse.
The device also resets the internal state machine to reading array data. The operation that was interrupted
should be reinitiated once the device is ready to accept another command sequence, to ensure data integrity.
Current is reduced for the duration of the RESET# pulse. When RESET# is held at VSS±0.3V, the device
draws CMOS standby current (ICC4). If RESET# is held at VIL but not within VSS±0.3V, the standby current
will be greater.
The RESET# pin may be tied to the system reset circuitry. A system reset would thus also reset the Flash
memory, enabling the system to read the boot-up firmware from the Flash memory.
If RESET# is asserted during a program or erase operation, the RY/BY# pin remains a “0” (busy) until the
internal reset operation is complete, which requires a time of tREADY (during Embedded Algorithms). The
system can thus monitor RY/BY# to determine whether the reset operation is complete. If RESET# is
asserted when a program or erase operation is not executing (RY/BY# pin is “1”), the reset operation is
completed within a time of tREADY (not during Embedded Algorithms). The system can read data tRH after the
RESET# pin returns to VIH.
Refer to Hardware Reset (RESET#) on page 49 for RESET# parameters and to Figure 17.2 on page 49 for
the timing diagram.
16
S29JL032J
S29JL032J_00_06 December 16, 2011
D a t a
8.8
S h e e t
Output Disable Mode
When the OE# input is at VIH, output from the device is disabled. The output pins are placed in the high
impedance state.
Table 8.2 S29JL032J Bank Architecture
Device
Model
Number
01, 02
Device
Model
Number
Bank 1
Bank 2
Bank 3
Bank 4
Mbit
Sector Size
Mbit
Sector Size
Mbit
Sector Size
Mbit
Sector Size
4 Mbit
Eight
8 kbyte/
4 kword,
seven
64 kbyte/
32 kword
12 Mbit
Twenty-four
64 kbyte/
32 kword
12 Mbit
Twenty-four
64 kbyte/
32 kword
4 Mbit
Eight 64 kbyte/
32 kword
Bank 1
Bank 2
Mbits
Sector Size
Mbit
21, 22
4 Mbit
Eight 8 kbyte/4 kword,
seven 64 kbyte/32 kword
28 Mbit
31, 32
8 Mbit
Eight 8 kbyte/4 kword,
fifteen 64 kbyte/32 kword
24 Mbit
Forty-eight
64 kbyte/32 kword
41, 42
16 Mbit
Eight 8 kbyte/4 kword,
thirty-one 64 kbyte/32 kword
16 Mbit
Thirty-two
64 kbyte/32 kword
December 16, 2011 S29JL032J_00_06
S29JL032J
Sector Size
Fifty-six
64 kbyte/32 kword
17
D a t a
S h e e t
S29JL032J (Model 01)
S29JL032J (Model 21)
Bank 2
Bank 3
Bank 2
Bank 2
Bank 4
S29JL032J (Model 31)
S29JL032J (Model 41)
Table 8.3 S29JL032J Sector Addresses - Top Boot Devices (Sheet 1 of 2)
18
Sector
Sector Address
A20–A12
Sector Size
(kbytes/kwords)
(x8)
Address Range
(x16)
Address Range
SA0
000000xxx
64/32
000000h-00FFFFh
000000h-07FFFh
SA1
000001xxx
64/32
010000h-01FFFFh
008000h-0FFFFh
SA2
000010xxx
64/32
020000h-02FFFFh
010000h-17FFFh
SA3
000011xxx
64/32
030000h-03FFFFh
018000h-01FFFFh
SA4
000100xxx
64/32
040000h-04FFFFh
020000h-027FFFh
SA5
000101xxx
64/32
050000h-05FFFFh
028000h-02FFFFh
SA6
000110xxx
64/32
060000h-06FFFFh
030000h-037FFFh
SA7
000111xxx
64/32
070000h-07FFFFh
038000h-03FFFFh
SA8
001000xxx
64/32
080000h-08FFFFh
040000h-047FFFh
SA9
001001xxx
64/32
090000h-09FFFFh
048000h-04FFFFh
SA10
001010xxx
64/32
0A0000h-0AFFFFh
050000h-057FFFh
SA11
001011xxx
64/32
0B0000h-0BFFFFh
058000h-05FFFFh
SA12
001100xxx
64/32
0C0000h-0CFFFFh
060000h-067FFFh
SA13
001101xxx
64/32
0D0000h-0DFFFFh
068000h-06FFFFh
SA14
001110xxx
64/32
0E0000h-0EFFFFh
070000h-077FFFh
SA15
001111xxx
64/32
0F0000h-0FFFFFh
078000h-07FFFFh
SA16
010000xxx
64/32
100000h-10FFFFh
080000h-087FFFh
SA17
010001xxx
64/32
110000h-11FFFFh
088000h-08FFFFh
SA18
010010xxx
64/32
120000h-12FFFFh
090000h-097FFFh
SA19
010011xxx
64/32
130000h-13FFFFh
098000h-09FFFFh
SA20
010100xxx
64/32
140000h-14FFFFh
0A0000h-0A7FFFh
SA21
010101xxx
64/32
150000h-15FFFFh
0A8000h-0AFFFFh
SA22
010110xxx
64/32
160000h-16FFFFh
0B0000h-0B7FFFh
SA23
010111xxx
64/32
170000h-17FFFFh
0B8000h-0BFFFFh
SA24
011000xxx
64/32
180000h-18FFFFh
0C0000h-0C7FFFh
0C8000h-0CFFFFh
SA25
011001xxx
64/32
190000h-19FFFFh
SA26
011010xxx
64/32
1A0000h-1AFFFFh
0D0000h-0D7FFFh
SA27
011011xxx
64/32
1B0000h-1BFFFFh
0D8000h-0DFFFFh
SA28
011100xxx
64/32
1C0000h-1CFFFFh
0E0000h-0E7FFFh
SA29
011101xxx
64/32
1D0000h-1DFFFFh
0E8000h-0EFFFFh
SA30
011110xxx
64/32
1E0000h-1EFFFFh
0F0000h-0F7FFFh
SA31
011111xxx
64/32
1F0000h-1FFFFFh
0F8000h-0FFFFFh
S29JL032J
S29JL032J_00_06 December 16, 2011
D a t a
S h e e t
S29JL032J (Model 21)
S29JL032J (Model 01)
Bank 2
Bank 2 (continued)
S29JL032J (Model 31)
Bank 1
Bank 1
Bank 1
Bank 1
Bank 2 (continued)
S29JL032J (Model 41)
Table 8.3 S29JL032J Sector Addresses - Top Boot Devices (Sheet 2 of 2)
December 16, 2011 S29JL032J_00_06
Sector
Sector Address
A20–A12
Sector Size
(kbytes/kwords)
(x8)
Address Range
(x16)
Address Range
SA32
100000xxx
64/32
200000h-20FFFFh
100000h-107FFFh
SA33
100001xxx
64/32
210000h-21FFFFh
108000h-10FFFFh
SA34
100010xxx
64/32
220000h-22FFFFh
110000h-117FFFh
SA35
100011xxx
64/32
230000h-23FFFFh
118000h-11FFFFh
SA36
100100xxx
64/32
240000h-24FFFFh
120000h-127FFFh
SA37
100101xxx
64/32
250000h-25FFFFh
128000h-12FFFFh
SA38
100110xxx
64/32
260000h-26FFFFh
130000h-137FFFh
SA39
100111xxx
64/32
270000h-27FFFFh
138000h-13FFFFh
SA40
101000xxx
64/32
280000h-28FFFFh
140000h-147FFFh
SA41
101001xxx
64/32
290000h-29FFFFh
148000h-14FFFFh
SA42
101010xxx
64/32
2A0000h-2AFFFFh
150000h-157FFFh
SA43
101011xxx
64/32
2B0000h-2BFFFFh
158000h-15FFFFh
SA44
101100xxx
64/32
2C0000h-2CFFFFh
160000h-167FFFh
SA45
101101xxx
64/32
2D0000h-2DFFFFh
168000h-16FFFFh
SA46
101110xxx
64/32
2E0000h-2EFFFFh
170000h-177FFFh
SA47
101111xxx
64/32
2F0000h-2FFFFFh
178000h-17FFFFh
SA48
110000xxx
64/32
300000h-30FFFFh
180000h-187FFFh
SA49
110001xxx
64/32
310000h-31FFFFh
188000h-18FFFFh
SA50
110010xxx
64/32
320000h-32FFFFh
190000h-197FFFh
SA51
110011xxx
64/32
330000h-33FFFFh
198000h-19FFFFh
SA52
110100xxx
64/32
340000h-34FFFFh
1A0000h-1A7FFFh
SA53
110101xxx
64/32
350000h-35FFFFh
1A8000h-1AFFFFh
SA54
110110xxx
64/32
360000h-36FFFFh
1B0000h-1BFFFFh
SA55
110111xxx
64/32
370000h-37FFFFh
1B8000h-1BFFFFh
SA56
111000xxx
64/32
380000h-38FFFFh
1C0000h-1C7FFFh
SA57
111001xxx
64/32
390000h-39FFFFh
1C8000h-1CFFFFh
SA58
111010xxx
64/32
3A0000h-3AFFFFh
1D0000h-1DFFFFh
SA59
111011xxx
64/32
3B0000h-3BFFFFh
1D8000h-1DFFFFh
SA60
111100xxx
64/32
3C0000h-3CFFFFh
1E0000h-1E7FFFh
SA61
111101xxx
64/32
3D0000h-3DFFFFh
1E8000h-1EFFFFh
SA62
111110xxx
64/32
3E0000h-3EFFFFh
1F0000h-1F7FFFh
SA63
111111000
8/4
3F0000h-3F1FFFh
1F8000h-1F8FFFh
SA64
111111001
8/4
3F2000h-3F3FFFh
1F9000h-1F9FFFh
SA65
111111010
8/4
3F4000h-3F5FFFh
1FA000h-1FAFFFh
SA66
111111011
8/4
3F6000h-3F7FFFh
1FB000h-1FBFFFh
SA67
111111100
8/4
3F8000h-3F9FFFh
1FC000h-1FCFFFh
SA68
111111101
8/4
3FA000h-3FBFFFh
1FD000h-1FDFFFh
SA69
111111110
8/4
3FC000h-3FDFFFh
1FE000h-1FEFFFh
SA70
111111111
8/4
3FE000h-3FFFFFh
1FF000h-1FFFFFh
S29JL032J
19
D a t a
S h e e t
Bank 2
20
S29JL032J (Model 22)
S29JL032J (Model 02)
Bank 1
Bank 2
Bank 2
Bank 1
Bank 1
Bank 1
S29JL032J (Model 32)
S29JL032J (Model 42)
Table 8.4 S29JL032J Sector Addresses - Bottom Boot Devices (Sheet 1 of 2)
Sector
Sector Address
A20–A12
Sector Size
(kbytes/kwords)
(x8)
Address Range
(x16)
Address Range
SA0
000000000
8/4
000000h-001FFFh
000000h-000FFFh
SA1
000000001
8/4
002000h-003FFFh
001000h-001FFFh
SA2
000000010
8/4
004000h-005FFFh
002000h-002FFFh
SA3
000000011
8/4
006000h-007FFFh
003000h-003FFFh
SA4
000000100
8/4
008000h-009FFFh
004000h-004FFFh
SA5
000000101
8/4
00A000h-00BFFFh
005000h-005FFFh
SA6
000000110
8/4
00C000h-00DFFFh
006000h-006FFFh
SA7
000000111
8/4
00E000h-00FFFFh
007000h-007FFFh
SA8
000001xxx
64/32
010000h-01FFFFh
008000h-00FFFFh
SA9
000010xxx
64/32
020000h-02FFFFh
010000h-017FFFh
SA10
000011xxx
64/32
030000h-03FFFFh
018000h-01FFFFh
SA11
000100xxx
64/32
040000h-04FFFFh
020000h-027FFFh
SA12
000101xxx
64/32
050000h-05FFFFh
028000h-02FFFFh
SA13
000110xxx
64/32
060000h-06FFFFh
030000h-037FFFh
SA14
000111xxx
64/32
070000h-07FFFFh
038000h-03FFFFh
SA15
001000xxx
64/32
080000h-08FFFFh
040000h-047FFFh
SA16
001001xxx
64/32
090000h-09FFFFh
048000h-04FFFFh
SA17
001010xxx
64/32
0A0000h-0AFFFFh
050000h-057FFFh
SA18
001011xxx
64/32
0B0000h-0BFFFFh
058000h-05FFFFh
SA19
001100xxx
64/32
0C0000h-0CFFFFh
060000h-067FFFh
SA20
001101xxx
64/32
0D0000h-0DFFFFh
068000h-06FFFFh
SA21
001110xxx
64/32
0E0000h-0EFFFFh
070000h-077FFFh
SA22
001111xxx
64/32
0F0000h-0FFFFFh
078000h-07FFFFh
SA23
010000xxx
64/32
100000h-10FFFFh
080000h-087FFFh
SA24
010001xxx
64/32
110000h-11FFFFh
088000h-08FFFFh
SA25
010010xxx
64/32
120000h-12FFFFh
090000h-097FFFh
SA26
010011xxx
64/32
130000h-13FFFFh
098000h-09FFFFh
SA27
010100xxx
64/32
140000h-14FFFFh
0A0000h-0A7FFFh
SA28
010101xxx
64/32
150000h-15FFFFh
0A8000h-0AFFFFh
SA29
010110xxx
64/32
160000h-16FFFFh
0B0000h-0B7FFFh
SA30
010111xxx
64/32
170000h-17FFFFh
0B8000h-0BFFFFh
SA31
011000xxx
64/32
180000h-18FFFFh
0C0000h-0C7FFFh
SA32
011001xxx
64/32
190000h-19FFFFh
0C8000h-0CFFFFh
SA33
011010xxx
64/32
1A0000h-1AFFFFh
0D0000h-0D7FFFh
SA34
011011xxx
64/32
1B0000h-1BFFFFh
0D8000h-0DFFFFh
SA35
011100xxx
64/32
1C0000h-1CFFFFh
0E0000h-0E7FFFh
SA36
011101xxx
64/32
1D0000h-1DFFFFh
0E8000h-0EFFFFh
SA37
011110xxx
64/32
1E0000h-1EFFFFh
0F0000h-0F7FFFh
SA38
011111xxx
64/32
1F0000h-1FFFFFh
0F8000h-0FFFFFh
S29JL032J
S29JL032J_00_06 December 16, 2011
D a t a
S h e e t
S29JL032J (Model 02)
S29JL032J (Model 22)
Bank 2 (continued)
Bank 4
Bank 2
Bank 2 (continued)
Bank 3
S29JL032J (Model 32)
S29JL032J (Model 42)
Table 8.4 S29JL032J Sector Addresses - Bottom Boot Devices (Sheet 2 of 2)
December 16, 2011 S29JL032J_00_06
Sector
Sector Address
A20–A12
Sector Size
(kbytes/kwords)
(x8)
Address Range
(x16)
Address Range
SA39
100000xxx
64/32
200000h-20FFFFh
100000h-107FFFh
SA40
100001xxx
64/32
210000h-21FFFFh
108000h-10FFFFh
SA41
100010xxx
64/32
220000h-22FFFFh
110000h-117FFFh
SA42
100011xxx
64/32
230000h-23FFFFh
118000h-11FFFFh
SA43
100100xxx
64/32
240000h-24FFFFh
120000h-127FFFh
SA44
100101xxx
64/32
250000h-25FFFFh
128000h-12FFFFh
SA45
100110xxx
64/32
260000h-26FFFFh
130000h-137FFFh
SA46
100111xxx
64/32
270000h-27FFFFh
138000h-13FFFFh
SA47
101000xxx
64/32
280000h-28FFFFh
140000h-147FFFh
SA48
101001xxx
64/32
290000h-29FFFFh
148000h-14FFFFh
SA49
101010xxx
64/32
2A0000h-2AFFFFh
150000h-157FFFh
SA50
101011xxx
64/32
2B0000h-2BFFFFh
158000h-15FFFFh
SA51
101100xxx
64/32
2C0000h-2CFFFFh
160000h-167FFFh
SA52
101101xxx
64/32
2D0000h-2DFFFFh
168000h-16FFFFh
SA53
101110xxx
64/32
2E0000h-2EFFFFh
170000h-177FFFh
SA54
111111xxx
64/32
2F0000h-2FFFFFh
178000h-17FFFFh
SA55
111000xxx
64/32
300000h-30FFFFh
180000h-187FFFh
SA56
110001xxx
64/32
310000h-31FFFFh
188000h-18FFFFh
SA57
110010xxx
64/32
320000h-32FFFFh
190000h-197FFFh
SA58
110011xxx
64/32
330000h-33FFFFh
198000h-19FFFFh
SA59
110100xxx
64/32
340000h-34FFFFh
1A0000h-1A7FFFh
SA60
110101xxx
64/32
350000h-35FFFFh
1A8000h-1AFFFFh
SA61
110110xxx
64/32
360000h-36FFFFh
1B0000h-1B7FFFh
SA62
110111xxx
64/32
370000h-37FFFFh
1B8000h-1BFFFFh
SA63
111000xxx
64/32
380000h-38FFFFh
1C0000h-1C7FFFh
SA64
111001xxx
64/32
390000h-39FFFFh
1C8000h-1CFFFFh
SA65
111010xxx
64/32
3A0000h-3AFFFFh
1D0000h-1D7FFFh
SA66
111011xxx
64/32
3B0000h-3BFFFFh
1D8000h-1DFFFFh
SA67
111100xxx
64/32
3C0000h-3CFFFFh
1E0000h-1E7FFFh
SA68
111101xxx
64/32
3D0000h-3DFFFFh
1E8000h-1EFFFFh
SA69
111110xxx
64/32
3E0000h-3EFFFFh
1F0000h-1F7FFFh
SA70
111111xxx
64/32
3F0000h-3F1FFFh
1F8000h-1FFFFFh
S29JL032J
21
D a t a
8.9
S h e e t
Autoselect Mode
The autoselect mode provides manufacturer and device identification, and sector protection verification,
through identifier codes output on DQ7–DQ0. This mode is primarily intended for programming equipment to
automatically match a device to be programmed with its corresponding programming algorithm. However, the
autoselect codes can also be accessed in-system through the command register.
When using programming equipment, the autoselect mode requires VID on address pin A9. Address pins
must be as shown in Table 8.5. In addition, when verifying sector protection, the sector address must appear
on the appropriate highest order address bits. Table 8.5 shows the remaining address bits that are don’t care.
When all necessary bits have been set as required, the programming equipment may then read the
corresponding identifier code on DQ7–DQ0. However, the autoselect codes can also be accessed in-system
through the command register, for instances when the S29JL032J is erased or programmed in a system
without access to high voltage on the A9 pin. The command sequence is illustrated in Table 10.1 on page 38.
Note that if a Bank Address (BA) on address bits A20, A19 and A18 is asserted during the third write cycle of
the autoselect command, the host system can read autoselect data from that bank and then immediately read
array data from another bank, without exiting the autoselect mode.
To access the autoselect codes in-system, the host system can issue the autoselect command via the
command register, as shown in Table 10.1 on page 38. This method does not require VID. Refer to
Autoselect Command Sequence on page 33 for more information.
Table 8.5 S29JL032J Autoselect Codes (High Voltage Method)
Description
Device ID
(Models 01, 02)
Manufacturer ID:
Spansion Products
CE#
OE#
WE#
A20
to
A12
L
L
H
BA
A11
to
A10
X
A9
A8
to
A7
VID
X
DQ15 to DQ8
A0
BYTE#
= VIH
BYTE#
= VIL
DQ7
to
DQ0
L
L
X
X
01h
A6
A5
to
A4
A3
A2
A1
L
X
L
L
Read Cycle 1
L
L
L
L
H
22h
Read Cycle 2
L
H
H
H
L
22h
L
L
H
BA
X
VID
X
Read Cycle 3
Device ID
(Models 21, 22)
Device ID
(Models 31, 32)
Device ID
(Models 41, 42)
X
L
7Eh
0Ah
X
H
H
H
H
22h
00h (bottom boot)
01h (top boot)
L
L
H
BA
X
VID
X
L
X
X
X
L
H
22h
X
L
L
H
BA
X
VID
X
L
X
X
X
L
H
22h
X
L
L
H
BA
X
VID
X
L
X
X
X
L
H
22h
X
56h (bottom boot)
55h (top boot)
53h (bottom boot)
50h (top boot)
5Fh (bottom boot)
5Ch (top boot)
Sector Protection
Verification
L
L
H
SA
X
VID
X
L
X
L
L
H
L
X
X
01h (protected),
00h (unprotected)
Secured Silicon
Indicator Bit (DQ6,
DQ7)
L
L
H
BA
X
VID
X
L
X
L
L
H
H
X
X
82h (Factory Locked),
42h (Customer
Locked),
02h (Not Locked)
Legend:
L = Logic Low = VIL
H = Logic High = VIH
BA = Bank Address
SA = Sector Address
X = Don’t care.
22
S29JL032J
S29JL032J_00_06 December 16, 2011
D a t a
8.10
S h e e t
Boot Sector/Sector Block Protection and Unprotection
Note: For the following discussion, the term “sector” applies to both boot sectors and sector blocks. A sector
block consists of two or more adjacent sectors that are protected or unprotected at the same time (see
Table 8.6).
The hardware sector protection feature disables both program and erase operations in any sector. The
hardware sector unprotection feature re-enables both program and erase operations in previously protected
sectors. Sector protection/unprotection can be implemented via two methods.
Table 8.6 S29JL032J Boot Sector/Sector Block Addresses for
Protection/Unprotection (Top Boot Devices)
Sector
SA0
A20-A12
Sector/
Sector Block Size
000000XXX
64 kbytes
000001XXX
SA1-SA3
000010XXX
192 (3X64) kbytes
000011XXX
SA4-SA7
0001XXXXX
SA8-SA11
0010XXXXX
256 (4X64) kbytes
256 (4X64) kbytes
SA12-SA15
0011XXXXX
256 (4X64) kbytes
SA16-SA19
0100XXXXX
256 (4X64) kbytes
SA20-SA23
0101XXXXX
256 (4X64) kbytes
SA24-SA27
0110XXXXX
256 (4X64) kbytes
SA28-SA31
0111XXXXX
256 (4X64) kbytes
SA32-SA35
1000XXXXX
256 (4X64) kbytes
SA36-SA39
1001XXXXX
256 (4X64) kbytes
SA40-SA43
1010XXXXX
256 (4X64) kbytes
SA44-SA47
1011XXXXX
256 (4X64) kbytes
SA48-SA51
1100XXXXX
256 (4X64) kbytes
SA52-SA55
1101XXXXX
256 (4X64) kbytes
SA56-SA59
1110XXXXX
256 (4X64) kbytes
111100XXX
SA60-SA62
111101XXX
192 (3X64) kbytes
111110XXX
SA63
111111000
8 kbytes
SA64
111111001
8 kbytes
SA65
111111010
8 kbytes
SA66
111111011
8 kbytes
SA67
111111100
8 kbytes
SA68
111111101
8 kbytes
SA69
111111110
8 kbytes
SA70
111111111
8 kbytes
December 16, 2011 S29JL032J_00_06
S29JL032J
23
D a t a
S h e e t
Table 8.7 S29JL032J Sector/Sector Block Addresses for
Protection/Unprotection (Bottom Boot Devices)
Sector
SA70
A20-A12
Sector/
Sector Block Size
111111XXX
64 kbytes
111110XXX
SA69-SA67
111101XXX
192 (3X64) kbytes
111100XXX
SA66-SA63
1110XXXXX
256 (4X64) kbytes
SA62-SA59
1101XXXXX
256 (4X64) kbytes
SA58-SA55
1100XXXXX
256 (4X64) kbytes
SA54-SA51
1011XXXXX
256 (4X64) kbytes
SA50-SA47
1010XXXXX
256 (4X64) kbytes
SA46-SA43
1001XXXXX
256 (4X64) kbytes
SA42-SA39
1000XXXXX
256 (4X64) kbytes
SA38-SA35
0111XXXXX
256 (4X64) kbytes
SA34-SA31
0110XXXXX
256 (4X64) kbytes
SA30-SA27
0101XXXXX
256 (4X64) kbytes
SA26-SA23
0100XXXXX
256 (4X64) kbytes
SA22-SA19
0011XXXXX
256 (4X64) kbytes
SA18-SA15
0010XXXXX
256 (4X64) kbytes
SA14-SA11
0001XXXXX
256 (4X64) kbytes
000011XXX
SA10-SA8
000010XXX
192 (3X64) kbytes
000001XXX
SA7
000000111
8 kbytes
SA6
000000110
8 kbytes
SA5
000000101
8 kbytes
SA4
000000100
8 kbytes
SA3
000000011
8 kbytes
SA2
000000010
8 kbytes
SA1
000000001
8 kbytes
SA0
000000000
8 kbytes
Sector Protect/Sector Unprotect requires VID on the RESET# pin only, and can be implemented either insystem or via programming equipment. Figure 8.2 on page 26 shows the algorithms and Figure 17.13
on page 56 shows the timing diagram. For sector unprotect, all unprotected sectors must first be protected
prior to the first sector unprotect write cycle. Note that the sector unprotect algorithm unprotects all sectors in
parallel. All previously protected sectors must be individually re-protected. To change data in protected
sectors efficiently, the temporary sector unprotect function is available. See Temporary Sector Unprotect
on page 25.
The device is shipped with all sectors unprotected. Optional Spansion programming service enable
programming and protecting sectors at the factory prior to shipping the device. Contact your local sales office
for details.
It is possible to determine whether a sector is protected or unprotected. See Autoselect Mode on page 22 for
details.
24
S29JL032J
S29JL032J_00_06 December 16, 2011
D a t a
8.11
S h e e t
Write Protect (WP#)
The Write Protect function provides a hardware method of protecting certain boot sectors without using VID.
This function is one of two provided by the WP#/ACC pin.
If the system asserts VIL on the WP#/ACC pin, the device disables program and erase functions in the two
outermost 8 kbyte boot sectors independently of whether those sectors were protected or unprotected using
the method described in Boot Sector/Sector Block Protection and Unprotection on page 23. The two
outermost 8 kbyte boot sectors are the two sectors containing the lowest addresses in a bottom-bootconfigured device, or the two sectors containing the highest addresses in a top-boot-configured device.
If the system asserts VIH on the WP#/ACC pin, the device reverts to whether the two outermost 8K Byte boot
sectors were last set to be protected or unprotected. That is, sector protection or unprotection for these two
sectors depends on whether they were last protected or unprotected using the method described in Boot
Sector/Sector Block Protection and Unprotection on page 23.
Note that the WP#/ACC pin must not be left floating or unconnected; inconsistent behavior of the device may
result.
Table 8.8 WP#/ACC Modes
WP# Input Voltage
8.12
Device Mode
VIL
Disables programming and erasing in the two outermost boot sectors
VIH
Enables programming and erasing in the two outermost boot sectors, dependent on whether they were last
protected or unprotected
VHH
Enables accelerated programming (ACC). See Accelerated Program Operation on page 15.
Temporary Sector Unprotect
Note: For the following discussion, the term “sector” applies to both sectors and sector blocks. A sector block
consists of two or more adjacent sectors that are protected or unprotected at the same time (see Table 8.6
on page 23 and Table 8.7 on page 24).
This feature allows temporary unprotection of previously protected sectors to change data in-system. The
Temporary Sector Unprotect mode is activated by setting the RESET# pin to VID. During this mode, formerly
protected sectors can be programmed or erased by selecting the sector addresses. Once VID is removed
from the RESET# pin, all the previously protected sectors are protected again. Figure 8.1 shows the
algorithm, and Figure 17.12 on page 55 shows the timing diagrams, for this feature. If the WP#/ACC pin is at
VIL, the two outermost boot sectors will remain protected during the Temporary sector Unprotect mode.
Figure 8.1 Temporary Sector Unprotect Operation
START
RESET# = VID
(Note 1)
Perform Erase or
Program Operations
RESET# = VIH
Temporary Sector
Unprotect Completed
(Note 2)
Notes:
1. All protected sectors unprotected (If WP#/ACC = VIL, the outermost two boot sectors will remain protected).
2. All previously protected sectors are protected once again.
December 16, 2011 S29JL032J_00_06
S29JL032J
25
D a t a
S h e e t
Figure 8.2 In-System Sector Protect/Unprotect Algorithms
START
START
Protect all sectors:
The indicated portion
of the sector protect
algorithm must be
performed for all
unprotected sectors
prior to issuing the
first sector
unprotect address
PLSCNT = 1
RESET# = VID
Wait 1 ms
Temporary Sector
Unprotect Mode
No
PLSCNT = 1
RESET# = VID
Wait 1 ms
No
First Write
Cycle = 60h?
First Write
Cycle = 60h?
Yes
Yes
Set up sector
address
No
All sectors
protected?
Sector Protect:
Write 60h to sector
address with
A6 = 0, A1 = 1,
A0 = 0
Yes
Set up first sector
address
Sector Unprotect:
Write 60h to sector
address with
A6 = 1, A1 = 1,
A0 = 0
Wait 150 µs
Increment
PLSCNT
Temporary Sector
Unprotect Mode
Verify Sector
Protect: Write 40h
to sector address
with A6 = 0,
A1 = 1, A0 = 0
Reset
PLSCNT = 1
Wait 15 ms
Read from
sector address
with A6 = 0,
A1 = 1, A0 = 0
Verify Sector
Unprotect: Write
40h to sector
address with
A6 = 1, A1 = 1,
A0 = 0
Increment
PLSCNT
No
No
PLSCNT
= 25?
Yes
Yes
No
Yes
Device failed
PLSCNT
= 1000?
Protect another
sector?
No
Yes
Remove VID
from RESET#
Device failed
Write reset
command
Sector Protect
Algorithm
Read from
sector address
with A6 = 1,
A1 = 1, A0 = 0
Data = 01h?
Sector Protect
complete
Set up
next sector
address
No
Data = 00h?
Yes
Last sector
verified?
No
Yes
Sector Unprotect
Algorithm
Remove VID
from RESET#
Write reset
command
Sector Unprotect
complete
26
S29JL032J
S29JL032J_00_06 December 16, 2011
D a t a
8.13
S h e e t
Secured Silicon Region
The Secured Silicon Region feature provides a Flash memory region that enables permanent part
identification through an Electronic Serial Number (ESN). The Secured Silicon Region is 256 bytes in length,
and may shipped unprotected, allowing customers to utilize that sector in any manner they choose, or may
shipped locked at the factory (upon customer request). The Secured Silicon Indicator Bit data will be 82h if
factory locked, 42h if customer locked, or 02h if neither. Refer to Table 8.5 on page 22 for more details.
The system accesses the Secured Silicon through a command sequence (see Enter Secured Silicon Region/
Exit Secured Silicon Region Command Sequence on page 33). After the system has written the Enter
Secured Silicon Region command sequence, it may read the Secured Silicon Region by using the addresses
normally occupied by the boot sectors. This mode of operation continues until the system issues the Exit
Secured Silicon Region command sequence, or until power is removed from the device. On power-up, or
following a hardware reset, the device reverts to sending commands to the first 256 bytes of Sector 0. Note
that the ACC function and unlock bypass modes are not available when the Secured Silicon Region is
enabled.
8.13.1
Factory Locked: Secured Silicon Region Programmed and Protected At the
Factory
In a factory locked device, the Secured Silicon Region is protected when the device is shipped from the
factory. The Secured Silicon Region cannot be modified in any way. The device is preprogrammed with both
a random number and a secure ESN. The 8-word random number is at addresses 000000h-000007h in word
mode (or 000000h-00000Fh in byte mode). The secure ESN is programmed in the next 8 words at addresses
000008h-00000Fh (or 000010h-00001Fh in byte mode). The device is available preprogrammed with one of
the following:
 A random, secure ESN only
 Customer code through Spansion programming services
 Both a random, secure ESN and customer code through Spansion programming services
Contact an your local sales office for details on using Spansion programming services.
8.13.2
Customer Lockable: Secured Silicon Region NOT Programmed or Protected
At the Factory
If the security feature is not required, the Secured Silicon Region can be treated as an additional Flash
memory space. The Secured Silicon Region can be read any number of times, but can be programmed and
locked only once. Note that the accelerated programming (ACC) and unlock bypass functions are not
available when programming the Secured Silicon Region.
 Write the three-cycle Enter Secured Silicon Region command sequence, and then follow the insystem
sector protect algorithm as shown in Figure 8.2 on page 26, except that RESET# may be at either VIH or
VID. This allows in-system protection of the Secured Silicon Region without raising any device pin to a high
voltage. Note that this method is only applicable to the Secured Silicon Region.
 To verify the protect/unprotect status of the Secured Silicon Region, follow the algorithm shown in
Figure 8.3 on page 28.
Once the Secured Silicon Region is locked and verified, the system must write the Exit Secured Silicon
Region command sequence to return to reading and writing the remainder of the array. The Secured Silicon
Region lock must be used with caution since, once locked, there is no procedure available for unlocking the
Secured Silicon Region area and none of the bits in the Secured Silicon Region memory space can be
modified in any way.
December 16, 2011 S29JL032J_00_06
S29JL032J
27
D a t a
S h e e t
Figure 8.3 Secured Silicon Region Protect Verify
START
RESET# =
VIH or VID
Wait 1 ms
Write 60h to
any address
Write 40h to Secure
Silicon Region address
with A6 = 0,
A1 = 1, A0 = 0
Read from Secure
Silicon Region address
with A6 = 0,
A1 = 1, A0 = 0
8.14
If data = 00h,
Secure Silicon Region
is unprotected.
If data = 01h,
Secure Silicon Region
is protected.
Remove VIH or VID
from RESET#
Secured Silicon Region
exit command
Secure Silicon Region
Protect Verify
complete
Hardware Data Protection
The command sequence requirement of unlock cycles for programming or erasing provides data protection
against inadvertent writes (refer to Table 10.1 on page 38 for command definitions). In addition, the following
hardware data protection measures prevent accidental erasure or programming, which might otherwise be
caused by spurious system level signals during VCC power-up and power-down transitions, or from system
noise.
8.14.1
Low VCC Write Inhibit
When VCC is less than VLKO, the device does not accept any write cycles. This protects data during VCC
power-up and power-down. The command register and all internal program/erase circuits are disabled, and
the device resets to the read mode. Subsequent writes are ignored until VCC is greater than VLKO. The
system must provide the proper signals to the control pins to prevent unintentional writes when VCC is greater
than VLKO.
8.14.2
Write Pulse “Glitch” Protection
Noise pulses of less than 5 ns (typical) on OE#, CE# or WE# do not initiate a write cycle.
8.14.3
Logical Inhibit
Write cycles are inhibited by holding any one of OE# = VIL, CE# = VIH or WE# = VIH. To initiate a write cycle,
CE# and WE# must be a logical zero while OE# is a logical one.
8.14.4
Power-Up Write Inhibit
If WE# = CE# = VIL and OE# = VIH during power up, the device does not accept commands on the rising
edge of WE#. The internal state machine is automatically reset to the read mode on power-up.
28
S29JL032J
S29JL032J_00_06 December 16, 2011
D a t a
S h e e t
9. Common Flash Memory Interface (CFI)
The Common Flash Interface (CFI) specification outlines device and host system software interrogation
handshake, which allows specific vendor-specified software algorithms to be used for entire families of
devices. Software support can then be device-independent, JEDEC ID-independent, and forward- and
backward-compatible for the specified flash device families. Flash vendors can standardize their existing
interfaces for long-term compatibility.
This device enters the CFI Query mode when the system writes the CFI Query command, 98h, to address
55h in word mode (or address AAh in byte mode), any time the device is ready to read array data. The system
can read CFI information at the addresses given in Table 9.1. To terminate reading CFI data, the system
must write the reset command. The CFI Query mode is not accessible when the device is executing an
Embedded Program or embedded Erase algorithm.
The system can also write the CFI query command when the device is in the autoselect mode via the
command register only (high voltage method does not apply). The device enters the CFI query mode, and the
system can read CFI data at the addresses given in Table 9.1. The system must write the reset command to
return to reading array data.
For further information, please refer to the CFI Specification and CFI Publication 100. Contact your local sales
office for copies of these documents.
Table 9.1 CFI Query Identification String
Addresses
(Word Mode)
Addresses
(Byte Mode)
Data
10h
11h
12h
20h
22h
24h
0051h
0052h
0059h
Query Unique ASCII string “QRY”
13h
14h
26h
28h
0002h
0000h
Primary OEM Command Set
15h
16h
2Ah
2Ch
0040h
0000h
Address for Primary Extended Table
17h
18h
2Eh
30h
0000h
0000h
Alternate OEM Command Set (00h = none exists)
19h
1Ah
32h
34h
0000h
0000h
Address for Alternate OEM Extended Table (00h = none exists)
Description
Table 9.2 System Interface String
Addresses
(Word Mode)
Addresses
(Byte Mode)
Data
Description
1Bh
36h
0027h
VCC Min. (write/erase)
D7–D4: volt, D3–D0: 100 millivolt
1Ch
38h
0036h
VCC Max. (write/erase)
D7–D4: volt, D3–D0: 100 millivolt
1Dh
3Ah
0000h
VPP Min. voltage (00h = no VPP pin present)
1Eh
3Ch
0000h
VPP Max. voltage (00h = no VPP pin present)
1Fh
3Eh
0003h
Typical timeout per single byte/word write 2N µs
20h
40h
0000h
Typical timeout for Min. size buffer write 2N µs (00h = not supported)
21h
42h
0009h
Typical timeout per individual block erase 2N ms
22h
44h
000Fh
Typical timeout for full chip erase 2N ms (00h = not supported)
23h
46h
0004h
Max. timeout for byte/word write 2N times typical
24h
48h
0000h
Max. timeout for buffer write 2N times typical
25h
4Ah
0004h
Max. timeout per individual block erase 2N times typical
26h
4Ch
0000h
Max. timeout for full chip erase 2N times typical (00h = not supported)
December 16, 2011 S29JL032J_00_06
S29JL032J
29
D a t a
S h e e t
Table 9.3 Device Geometry Definition
30
Addresses
(Word Mode)
Addresses
(Byte Mode)
Data
27h
4Eh
0016h
Device Size = 2N byte
28h
29h
50h
52h
0002h
0000h
Flash Device Interface description (refer to CFI publication 100)
2Ah
2Bh
54h
56h
0000h
0000h
Max. number of byte in multi-byte write = 2N
(00h = not supported)
2Ch
58h
0002h
Number of Erase Block Regions within device
2Dh
2Eh
2Fh
30h
5Ah
5Ch
5Eh
60h
0007h
0000h
0020h
0000h
Erase Block Region 1 Information
(refer to the CFI specification or CFI publication 100)
31h
32h
33h
34h
62h
64h
66h
68h
003Eh
0000h
0000h
0001h
Erase Block Region 2 Information
(refer to the CFI specification or CFI publication 100)
35h
36h
37h
38h
6Ah
6Ch
6Eh
70h
0000h
0000h
0000h
0000h
Erase Block Region 3 Information
(refer to the CFI specification or CFI publication 100)
39h
3Ah
3Bh
3Ch
72h
74h
76h
78h
0000h
0000h
0000h
0000h
Erase Block Region 4 Information
(refer to the CFI specification or CFI publication 100)
Description
S29JL032J
S29JL032J_00_06 December 16, 2011
D a t a
S h e e t
Table 9.4 Primary Vendor-Specific Extended Query
Addresses
(Word Mode)
Addresses
(Byte Mode)
Data
40h
41h
42h
80h
82h
84h
0050h
0052h
0049h
Query-unique ASCII string “PRI”
43h
86h
0031h
Major version number, ASCII (reflects modifications to the silicon)
44h
88h
0033h
Minor version number, ASCII (reflects modifications to the CFI table)
Description
45h
8Ah
000Ch
Address Sensitive Unlock (Bits 1-0)
0 = Required, 1 = Not Required
Process Technology (Bits 7-2)
0011 = 0.11 µm Floating Gate
46h
8Ch
0002h
Erase Suspend
0 = Not Supported, 1 = To Read Only, 2 = To Read & Write
47h
8Eh
0001h
Sector Protect
0 = Not Supported, X = Number of sectors in per group
48h
90h
0001h
Sector Temporary Unprotect
00 = Not Supported, 01 = Supported
49h
92h
0004h
Sector Protect/Unprotect scheme
01 = 29F040 mode, 02 = 29F016 mode, 03 = 29F400, 04 = 29LV800 mode
Number of sectors (excluding Bank 1)
4Ah
94h
00XXh
XX = 38 (models 01, 02, 21, 22)
XX = 30 (models 31, 32)
XX = 20 (models 41, 42)
4Bh
96h
0000h
Burst Mode Type
00 = Not Supported, 01 = Supported
4Ch
98h
0000h
Page Mode Type
00 = Not Supported, 01 = 4 Word Page, 02 = 8 Word Page
4Dh
9Ah
0085h
4Eh
9Ch
0095h
4Fh
9Eh
000Xh
50h
A0h
0000h
ACC (Acceleration) Supply Minimum
00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV
ACC (Acceleration) Supply Maximum
00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV
Top/Bottom Boot Sector Flag
02h = Bottom Boot Device, 03h = Top Boot Device
Program Suspend
0 = Not supported, 1 = Supported
Bank Organization
57h
AEh
000Xh
00 = Data at 4Ah is zero
X = 4 (4 banks, models 01, 02)
X = 2 (2 banks, all other models)
Bank 1 Region Information - Number of sectors on Bank 1
58h
B0h
00XXh
XX = 0F (models 01, 02, 21, 22)
XX = 17 (models 31, 32)
XX = 27 (models 41, 42)
Bank 2 Region Information - Number of sectors in Bank 2
XX = 18 (models 01, 02)
59h
B2h
00XXh
XX = 38 (models 21, 22)
XX = 30 (models 31, 32)
XX = 20 (models 41, 42)
Bank 3 Region Information - Number of sectors in Bank 3
5Ah
B4h
00XXh
XX = 18 (models 01, 02)
XX = 00 (all other models)
Bank 4 Region Information - Number of sectors in Bank 4
5Bh
B6h
00XXh
XX = 08 (models 01, 02)
XX = 00 (all other models)
December 16, 2011 S29JL032J_00_06
S29JL032J
31
D a t a
S h e e t
10. Command Definitions
Writing specific address and data sequences into the command register initiates device operations.
Table 10.1 on page 38 defines the valid register command sequences. Writing incorrect address and data
values or writing them in the improper sequence may place the device in an unknown state. A hardware reset
may be required to return the device to reading array data.
All addresses are latched on the falling edge of WE# or CE#, whichever happens later. All data is latched on
the rising edge of WE# or CE#, whichever happens first. Refer to AC Characteristics on page 48 for timing
diagrams.
10.1
Reading Array Data
The device is automatically set to reading array data after device power-up. No commands are required to
retrieve data. Each bank is ready to read array data after completing an Embedded Program or Embedded
Erase algorithm.
After the device accepts an Erase Suspend command, the corresponding bank enters the erase-suspendread mode, after which the system can read data from any non-erase-suspended sector within the same
bank. The system can read array data using the standard read timing, except that if it reads at an address
within erase-suspended sectors, the device outputs status data. After completing a programming operation in
the Erase Suspend mode, the system may once again read array data with the same exception. See Erase
Suspend/Erase Resume Commands on page 37 for more information.
The system must issue the reset command to return a bank to the read (or erase-suspend-read) mode if DQ5
goes high during an active program or erase operation, or if the bank is in the autoselect mode. See Reset
Command on page 32, for more information.
See also Requirements for Reading Array Data on page 15 for more information. Read-Only Operations
on page 48 provides the read parameters, and Figure 17.1 on page 48 shows the timing diagram.
10.2
Reset Command
Writing the reset command resets the banks to the read or erase-suspend-read mode.
The reset command may be written between the sequence cycles in an erase command sequence before
erasing begins. This resets the bank to which the system was writing to the read mode. Once erasure begins,
however, the device ignores reset commands until the operation is complete.
The reset command may be written between the sequence cycles in a program command sequence before
programming begins. This resets the bank to which the system was writing to the read mode. If the program
command sequence is written to a bank that is in the Erase Suspend mode, writing the reset command
returns that bank to the erase-suspend-read mode. Once programming begins, however, the device ignores
reset commands until the operation is complete.
The reset command may be written between the sequence cycles in an autoselect command sequence.
Once in the autoselect mode, the reset command must be written to return to the read mode. If a bank
entered the autoselect mode while in the Erase Suspend mode, writing the reset command returns that bank
to the erase-suspend-read mode.
If DQ5 goes high during a program or erase operation, writing the reset command returns the bank to the
read mode (or erase-suspend-read mode if that bank was in Erase Suspend). Please note that the RY/BY#
signal remains low until this reset is issued.
32
S29JL032J
S29JL032J_00_06 December 16, 2011
D a t a
10.3
S h e e t
Autoselect Command Sequence
The autoselect command sequence allows the host system to access the manufacturer and device codes,
and determine whether or not a sector is protected. The autoselect command sequence may be written to an
address within a bank that is either in the read or erase-suspend-read mode. The autoselect command may
not be written while the device is actively programming or erasing in another bank.
The autoselect command sequence is initiated by first writing two unlock cycles. This is followed by a third
write cycle that contains the bank address and the autoselect command. The bank then enters the autoselect
mode. The system may read any number of autoselect codes without reinitiating the command sequence.
Table 10.1 on page 38 shows the address and data requirements. To determine sector protection
information, the system must write to the appropriate bank address (BA) and sector address (SA). Table 8.3
on page 18 and Table 8.4 on page 20 show the address range and bank number associated with each
sector.
The system must write the reset command to return to the read mode (or erase-suspend-read mode if the
bank was previously in Erase Suspend).
10.4
Enter Secured Silicon Region/Exit Secured Silicon Region Command
Sequence
The system can access the Secured Silicon Region region by issuing the three-cycle Enter Secured Silicon
Region command sequence. The device continues to access the Secured Silicon Region until the system
issues the four-cycle Exit Secured Silicon Region command sequence. The Exit Secured Silicon Region
command sequence returns the device to normal operation. The Secured Silicon Region is not accessible
when the device is executing an Embedded Program or embedded Erase algorithm. Table 10.1 on page 38
shows the address and data requirements for both command sequences. See also Secured Silicon Region
on page 27 for further information. Note that the ACC function and unlock bypass modes are not available
when the Secured Silicon Region is enabled.
10.5
Byte/Word Program Command Sequence
The system may program the device by word or byte, depending on the state of the BYTE# pin. Programming
is a four-bus-cycle operation. The program command sequence is initiated by writing two unlock write cycles,
followed by the program set-up command. The program address and data are written next, which in turn
initiate the Embedded Program algorithm. The system is not required to provide further controls or timings.
The device automatically provides internally generated program pulses and verifies the programmed cell
margin. Table 10.1 on page 38 shows the address and data requirements for the byte program command
sequence.
When the Embedded Program algorithm is complete, that bank then returns to the read mode and addresses
are no longer latched. The system can determine the status of the program operation by using DQ7, DQ6, or
RY/BY#. Refer to Write Operation Status on page 39 for information on these status bits.
Any commands written to the device during the Embedded Program Algorithm are ignored. Note that a
hardware reset immediately terminates the program operation. The program command sequence should be
reinitiated once that bank has returned to the read mode, to ensure data integrity. Note that the Secured
Silicon Region, autoselect, and CFI functions are unavailable when a program operation is in progress.
Programming is allowed in any sequence and across sector boundaries. A bit cannot be programmed from
“0” back to a “1.” Attempting to do so may cause that bank to set DQ5 = 1, or cause the DQ7 and DQ6
status bits to indicate the operation was successful. However, a succeeding read will show that the data is still
“0.” Only erase operations can convert a “0” to a “1.”
December 16, 2011 S29JL032J_00_06
S29JL032J
33
D a t a
10.5.1
S h e e t
Unlock Bypass Command Sequence
The unlock bypass feature allows the system to program bytes or words to a bank faster than using the
standard program command sequence. The unlock bypass command sequence is initiated by first writing two
unlock cycles. This is followed by a third write cycle containing the unlock bypass command, 20h. That bank
then enters the unlock bypass mode. A two-cycle unlock bypass program command sequence is all that is
required to program in this mode. The first cycle in this sequence contains the unlock bypass program
command, A0h; the second cycle contains the program address and data. Additional data is programmed in
the same manner. This mode dispenses with the initial two unlock cycles required in the standard program
command sequence, resulting in faster total programming time. Table 10.1 on page 38 shows the
requirements for the command sequence.
During the unlock bypass mode, only the Unlock Bypass Program and Unlock Bypass Reset commands are
valid. To exit the unlock bypass mode, the system must issue the two-cycle unlock bypass reset command
sequence. (Table 10.1 on page 38).
The device offers accelerated program operations through the WP#/ACC pin. When the system asserts VHH
on the WP#/ACC pin, the device automatically enters the Unlock Bypass mode. The system may then write
the two-cycle Unlock Bypass program command sequence. The device uses the higher voltage on the WP#/
ACC pin to accelerate the operation. Note that the WP#/ACC pin must not be at VHH for any operation other
than accelerated programming, or device damage may result. In addition, the WP#/ACC pin must not be left
floating or unconnected; inconsistent behavior of the device may result.
Figure 10.1 illustrates the algorithm for the program operation. Refer to Erase and Program Operations
on page 51 for parameters, and Figure 17.5 on page 52 for timing diagrams.
Figure 10.1 Program Operation
START
Write Program
Command Sequence
Data Poll
from System
Embedded
Program
algorithm
in progress
Verify Data?
No
Yes
Increment Address
No
Last Address?
Yes
Programming
Completed
Note:
See Table 10.1 on page 38 for program command sequence.
34
S29JL032J
S29JL032J_00_06 December 16, 2011
D a t a
10.6
S h e e t
Chip Erase Command Sequence
Chip erase is a six bus cycle operation. The chip erase command sequence is initiated by writing two unlock
cycles, followed by a set-up command. Two additional unlock write cycles are then followed by the chip erase
command, which in turn invokes the Embedded Erase algorithm. The device does not require the system to
preprogram prior to erase. The Embedded Erase algorithm automatically preprograms and verifies the entire
memory for an all zero data pattern prior to electrical erase. The system is not required to provide any
controls or timings during these operations. Table 10.1 on page 38 shows the address and data requirements
for the chip erase command sequence.
When the Embedded Erase algorithm is complete, that bank returns to the read mode and addresses are no
longer latched. The system can determine the status of the erase operation by using DQ7, DQ6, DQ2, or RY/
BY#. Refer to Write Operation Status on page 39 for information on these status bits.
Any commands written during the chip erase operation are ignored. However, note that a hardware reset
immediately terminates the erase operation. If that occurs, the chip erase command sequence should be
reinitiated once that bank has returned to reading array data, to ensure data integrity. Note that the Secured
Silicon Region, autoselect, and CFI functions are unavailable when an erase operation is in progress.
Figure 10.2 on page 36 illustrates the algorithm for the erase operation. Refer to Erase and Program
Operations on page 51 for parameters, and Figure 17.7 on page 53 for timing diagrams.
10.7
Sector Erase Command Sequence
Sector erase is a six bus cycle operation. The sector erase command sequence is initiated by writing two
unlock cycles, followed by a set-up command. Two additional unlock cycles are written, and are then followed
by the address of the sector to be erased, and the sector erase command. Table 10.1 on page 38 shows the
address and data requirements for the sector erase command sequence.
The device does not require the system to preprogram prior to erase. The Embedded Erase algorithm
automatically programs and verifies the entire sector for an all zero data pattern prior to electrical erase. The
system is not required to provide any controls or timings during these operations.
After the command sequence is written, a sector erase time-out of 50 µs occurs. During the time-out period,
additional sector addresses and sector erase commands may be written. However, these additional erase
commands are only one bus cycle long and should be identical to the sixth cycle of the standard erase
command explained above. Loading the sector erase buffer may be done in any sequence, and the number
of sectors may be from one sector to all sectors. The time between these additional cycles must be less than
50 µs, otherwise erasure may begin. Any sector erase address and command following the exceeded timeout may or may not be accepted. It is recommended that processor interrupts be disabled during this time to
ensure all commands are accepted. The interrupts can be re-enabled after the last Sector Erase command is
written. If any command other than 30h, B0h, F0h is input during the time-out period, the normal
operation will not be guaranteed. The system must rewrite the command sequence and any additional
addresses and commands.
The system can monitor DQ3 to determine if the sector erase timer has timed out (See DQ3: Sector Erase
Timer on page 43.). The time-out begins from the rising edge of the final WE# or CE# pulse (first rising edge)
in the command sequence.
When the Embedded Erase algorithm is complete, the bank returns to reading array data and addresses are
no longer latched. Note that while the Embedded Erase operation is in progress, the system can read data
from the non-erasing bank. The system can determine the status of the erase operation by reading DQ7,
DQ6, DQ2, or RY/BY# in the erasing bank. Refer to Write Operation Status on page 39 for information on
these status bits.
Once the sector erase operation has begun, only the Erase Suspend command is valid. All other commands
are ignored. However, note that a hardware reset immediately terminates the erase operation. If that occurs,
the sector erase command sequence should be reinitiated once that bank has returned to reading array data,
to ensure data integrity. Note that the Secured Silicon Region, autoselect, and CFI functions are unavailable
when an erase operation is in progress.
Figure 10.2 on page 36 illustrates the algorithm for the erase operation. Refer to Erase and Program
Operations on page 51 for parameters, and Figure 17.7 on page 53 for timing diagrams.
December 16, 2011 S29JL032J_00_06
S29JL032J
35
D a t a
S h e e t
Figure 10.2 Erase Operation
START
Write Erase
Command Sequence
(Notes 1, 2)
Data Poll to Erasing
Bank from System
No
Embedded
Erase
algorithm
in progress
Data = FFh?
Yes
Erasure Completed
Notes:
1. See Table 10.1 on page 38 for erase command sequence.
2. See DQ3: Sector Erase Timer on page 43 for information on the sector erase timer.
36
S29JL032J
S29JL032J_00_06 December 16, 2011
D a t a
10.8
S h e e t
Erase Suspend/Erase Resume Commands
The Erase Suspend command, B0h, allows the system to interrupt a sector erase operation and then read
data from, or program data to, any sector not selected for erasure. The bank address is required when writing
this command. This command is valid only during the sector erase operation, including the 50 µs time-out
period during the sector erase command sequence. The Erase Suspend command is ignored if written during
the chip erase operation or Embedded Program algorithm. The bank address must contain one of the sectors
currently selected for erase.
When the Erase Suspend command is written during the sector erase operation, the device requires a
maximum of 35 µs to suspend the erase operation. However, when the Erase Suspend command is written
during the sector erase time-out, the device immediately terminates the time-out period and suspends the
erase operation.
After the erase operation has been suspended, the bank enters the erase-suspend-read mode. The system
can read data from or program data to any sector not selected for erasure. (The device “erase suspends” all
sectors selected for erasure.) It is not recommended to program the Secured Silicon Region after an erase
suspend, as proper device functionality cannot be guaranteed. Reading at any address within erasesuspended sectors produces status information on DQ7–DQ0. The system can use DQ7, or DQ6 and DQ2
together, to determine if a sector is actively erasing or is erase-suspended. Refer to Write Operation Status
on page 39 for information on these status bits.
After an erase-suspended program operation is complete, the bank returns to the erase-suspend-read mode.
The system can determine the status of the program operation using the DQ7 or DQ6 status bits, just as in
the standard Byte Program operation. Refer to Write Operation Status on page 39 for more information.
In the erase-suspend-read mode, the system can also issue the autoselect command sequence. The device
allows reading autoselect codes even at addresses within erasing sectors, since the codes are not stored in
the memory array. When the device exits the autoselect mode, the device reverts to the Erase Suspend
mode, and is ready for another valid operation. Refer to Autoselect Mode on page 22 and Autoselect
Command Sequence on page 33 for details.
To resume the sector erase operation, the system must write the Erase Resume command. The bank
address of the erase-suspended bank is required when writing this command. Further writes of the Resume
command are ignored. Another Erase Suspend command can be written after the chip has resumed erasing.
December 16, 2011 S29JL032J_00_06
S29JL032J
37
D a t a
S h e e t
Cycles
Table 10.1 S29JL032J Command Definitions
Command
Sequence
(Note 1)
Read (Note 6)
Reset (Note 7)
Data
1
RA
RD
1
XXX
F0
555
4
Autoselect (Note 8)
Byte
Word
Secured Silicon Region
Factory Protect (Note 10) Byte
Boot Sector/Sector Block
Protect Verify (Note 11)
Word
Word
Enter Secured Silicon Region
Word
Exit Secured Silicon Region
Word
Program
Word
Unlock Bypass
2AA
2
XXX
A0
PA
PD
2
XXX
90
XXX
00
6
Byte
Word
Sector Erase (Note 17)
2AA
AA
AAA
Byte
AAA
Erase Suspend (Note 14)
1
BA
B0
1
BA
30
Word
CFI Query (Note 16)
A0
PA
PD
555
80
555
55
2AA
AA
AAA
555
80
AAA
10
AAA
2AA
AA
AAA
555
55
555
55
SA
30
555
55
1
Byte
00
555
555
Erase Resume (Note 15)
XXX
AAA
2AA
AA
90
20
55
555
555
6
00/01
AAA
Unlock Bypass Reset (Note 13)
Chip Erase
(SA)X02
(SA)X04
555
55
555
555
82/02
AAA
Unlock Bypass Program (Note 12)
Word
See
Table
8.5
555
55
AA
(BA)X0F
(BA)X1E
555
555
AAA
See
Table
8.5
AAA
2AA
555
3
Byte
(BA)X0E
(BA)X1C
88
55
AA
Data
555
555
AAA
Addr
AAA
2AA
555
4
Byte
Data
(BA)X03
90
55
AA
Sixth
Addr
(BA)X06
(BA)555
555
AAA
See
Table
8.5
(BA)X02
(BA)AAA
2AA
555
4
Byte
(BA)X01
90
55
AA
AAA
01
(BA)555
555
555
3
Byte
(BA)X00
(BA)AAA
2AA
AA
90
90
55
555
AAA
Data
(BA)AAA
2AA
555
4
Byte
Fifth
Addr
(BA)555
55
AA
Fourth
Data
(BA)AAA
555
555
Addr
(BA)555
2AA
AA
AAA
Third
55
555
AAA
4
Data
2AA
555
6
Byte
Addr
AA
AAA
Word
Device ID (Note 9)
Second
Addr
Word
Manufacturer ID
Bus Cycles (Notes 2–5)
First
98
AA
Legend:
X = Don’t care
RA = Address of the memory location to be read.
RD = Data read from location RA during read operation.
PA = Address of the memory location to be programmed. Addresses latch on the falling edge of the WE# or CE# pulse, whichever happens later.
PD = Data to be programmed at location PA. Data latches on the rising edge of WE# or CE# pulse, whichever happens first.
SA = Address of the sector to be verified (in autoselect mode) or erased. Address bits A20–A12 uniquely select any sector.
Refer to Table 8.3 on page 18 and Table 8.4 on page 20 for information on sector addresses.
BA = Address of the bank that is being switched to autoselect mode, is in bypass mode, or is being erased. A20–A18 uniquely select a bank.
Notes:
1. See Table 8.1 on page 14 for description of bus operations.
2. All values are in hexadecimal.
3. Except for the read cycle and the fourth, fifth, and sixth cycle of the autoselect command sequence, all bus cycles are write cycles.
4. Data bits DQ15–DQ8 are don’t care in command sequences, except for RD and PD.
5. Unless otherwise noted, address bits A20–A11 are don’t cares for unlock and command cycles, unless SA or PA is required.
6. No unlock or command cycles required when bank is reading array data.
7. The Reset command is required to return to the read mode (or to the erase-suspend-read mode if previously in Erase Suspend) when a bank is in the autoselect
mode, or if DQ5 goes high (while the bank is providing status information).
8. The fourth cycle of the autoselect command sequence is a read cycle. The system must provide the bank address to obtain the manufacturer ID, device ID, or
Secured Silicon Region factory protect information. Data bits DQ15–DQ8 are don’t care. While reading the autoselect addresses, the bank address must be the
same until a reset command is given. See Autoselect Command Sequence on page 33 for more information.
9. For models 01, 02, the device ID must be read across the fourth, fifth, and sixth cycles.
10. The data is 82h for factory locked, 42h for customer locked, and 02h for not factory/customer locked.
38
S29JL032J
S29JL032J_00_06 December 16, 2011
D a t a
S h e e t
11. The data is 00h for an unprotected sector/sector block and 01h for a protected sector/sector block.
12. The Unlock Bypass command is required prior to the Unlock Bypass Program command.
13. The Unlock Bypass Reset command is required to return to the read mode when the bank is in the unlock bypass mode.
14. The system may read and program in non-erasing sectors, or enter the autoselect mode, when in the Erase Suspend mode. The Erase Suspend command is
valid only during a sector erase operation, and requires the bank address.
15. The Erase Resume command is valid only during the Erase Suspend mode, and requires the bank address.
16. Command is valid when device is ready to read array data or when device is in autoselect mode.
17. Additional sector erase commands during the time-out period after an initial sector erase are one cycle long and identical to the sixth
cycle of the sector erase command sequence (SA / 30).
11. Write Operation Status
The device provides several bits to determine the status of a program or erase operation: DQ2, DQ3, DQ5,
DQ6, and DQ7. Table 11.1 on page 43 and the following subsections describe the function of these bits. DQ7
and DQ6 each offer a method for determining whether a program or erase operation is complete or in
progress. The device also provides a hardware-based output signal, RY/BY#, to determine whether an
Embedded Program or Erase operation is in progress or has been completed.
11.1
DQ7: Data# Polling
The Data# Polling bit, DQ7, indicates to the host system whether an Embedded Program or Erase algorithm
is in progress or completed, or whether a bank is in Erase Suspend. Data# Polling is valid after the rising
edge of the final WE# pulse in the command sequence.
During the Embedded Program algorithm, the device outputs on DQ7 the complement of the datum
programmed to DQ7. This DQ7 status also applies to programming during Erase Suspend. When the
Embedded Program algorithm is complete, the device outputs the datum programmed to DQ7. The system
must provide the program address to read valid status information on DQ7. If a program address falls within a
protected sector, Data# Polling on DQ7 is active for approximately 1 µs, then that bank returns to the read
mode.
During the Embedded Erase algorithm, Data# Polling produces a “0” on DQ7. When the Embedded Erase
algorithm is complete, or if the bank enters the Erase Suspend mode, Data# Polling produces a “1” on DQ7.
The system must provide an address within any of the sectors selected for erasure to read valid status
information on DQ7.
After an erase command sequence is written, if all sectors selected for erasing are protected, Data# Polling
on DQ7 is active for approximately 3 ms, then the bank returns to the read mode. If not all selected sectors
are protected, the Embedded Erase algorithm erases the unprotected sectors, and ignores the selected
sectors that are protected. However, if the system reads DQ7 at an address within a protected sector, the
status may not be valid.
When the system detects DQ7 has changed from the complement to true data, it can read valid data at
DQ15–DQ0 (or DQ7–DQ0 for x8-only device) on the following read cycles. Just prior to the completion of an
Embedded Program or Erase operation, DQ7 may change asynchronously with DQ15–DQ8 (DQ7–DQ0 for
x8-only device) while Output Enable (OE#) is asserted low. That is, the device may change from providing
status information to valid data on DQ7. Depending on when the system samples the DQ7 output, it may read
the status or valid data. Even if the device has completed the program or erase operation and DQ7 has valid
data, the data outputs on DQ15–DQ0 may be still invalid. Valid data on DQ15–DQ0 (or DQ7–DQ0 for x8-only
device) will appear on successive read cycles.
Table 11.1 on page 43 shows the outputs for Data# Polling on DQ7. Figure 11.1 on page 40 shows the Data#
Polling algorithm. Figure 17.9 on page 54 shows the Data# Polling timing diagram.
December 16, 2011 S29JL032J_00_06
S29JL032J
39
D a t a
S h e e t
Figure 11.1 Data# Polling Algorithm
34!24
2EADå$1n$1
!DDRåå6!
$1åå$ATA
9ES
.O
.O
$1åå
9ES
2EADå$1n$1
!DDRåå6!
$1åå$ATA
9ES
.O
&!),
0!33
Notes:
1. VA = Valid address for programming. During a sector erase operation, a valid address is any sector address within the sector being
erased. During chip erase, a valid address is any non-protected sector address.
2. DQ7 should be rechecked even if DQ5 = “1” because DQ7 may change simultaneously with DQ5.
11.2
RY/BY#: Ready/Busy#
The RY/BY# is a dedicated, open-drain output pin which indicates whether an Embedded Algorithm is in
progress or complete. The RY/BY# status is valid after the rising edge of the final WE# pulse in the command
sequence. Since RY/BY# is an open-drain output, several RY/BY# pins can be tied together in parallel with a
pull-up resistor to VCC.
If the output is low (Busy), the device is actively erasing or programming. (This includes programming in the
Erase Suspend mode.) If the output is high (Ready), the device is in the read mode, the standby mode, or one
of the banks is in the erase-suspend-read mode.
Table 11.1 on page 43 shows the outputs for RY/BY#.
When DQ5 is set to “1”, RY/BY# will be in the BUSY state, or “0”.
11.3
DQ6: Toggle Bit I
Toggle Bit I on DQ6 indicates whether an Embedded Program or Erase algorithm is in progress or complete,
or whether the device has entered the Erase Suspend mode. Toggle Bit I may be read at any address, and is
valid after the rising edge of the final WE# pulse in the command sequence (prior to the program or erase
operation), and during the sector erase time-out.
40
S29JL032J
S29JL032J_00_06 December 16, 2011
D a t a
S h e e t
During an Embedded Program or Erase algorithm operation, successive read cycles to any address cause
DQ6 to toggle. The system may use either OE# or CE# to control the read cycles. When the operation is
complete, DQ6 stops toggling.
After an erase command sequence is written, if all sectors selected for erasing are protected, DQ6 toggles for
approximately 3 ms, then returns to reading array data. If not all selected sectors are protected, the
Embedded Erase algorithm erases the unprotected sectors, and ignores the selected sectors that are
protected.
The system can use DQ6 and DQ2 together to determine whether a sector is actively erasing or is erasesuspended. When the device is actively erasing (that is, the Embedded Erase algorithm is in progress), DQ6
toggles. When the device enters the Erase Suspend mode, DQ6 stops toggling. However, the system must
also use DQ2 to determine which sectors are erasing or erase-suspended. Alternatively, the system can use
DQ7 (see DQ7: Data# Polling on page 39).
If a program address falls within a protected sector, DQ6 toggles for approximately 1 µs after the program
command sequence is written, then returns to reading array data.
DQ6 also toggles during the erase-suspend-program mode, and stops toggling once the Embedded Program
algorithm is complete.
Figure 11.2 Toggle Bit Algorithm
START
Read Byte
(DQ7–DQ0)
Address =VA
Read Byte
(DQ7–DQ0)
Address =VA
Toggle Bit
= Toggle?
No
Yes
No
DQ5 = 1?
Yes
Read Byte Twice
(DQ7–DQ0)
Address = VA
Toggle Bit
= Toggle?
No
Yes
Program/Erase
Operation Not
Complete, Write
Reset Command
Program/Erase
Operation Complete
Note:
The system should recheck the toggle bit even if DQ5 = “1” because the toggle bit may stop toggling as DQ5 changes to “1.” See the
subsections on DQ6 and DQ2 for more information.
December 16, 2011 S29JL032J_00_06
S29JL032J
41
D a t a
11.4
S h e e t
DQ2: Toggle Bit II
The “Toggle Bit II” on DQ2, when used with DQ6, indicates whether a particular sector is actively erasing (that
is, the Embedded Erase algorithm is in progress), or whether that sector is erase-suspended. Toggle Bit II is
valid after the rising edge of the final WE# pulse in the command sequence.
DQ2 toggles when the system reads at addresses within those sectors that have been selected for erasure.
(The system may use either OE# or CE# to control the read cycles.) But DQ2 cannot distinguish whether the
sector is actively erasing or is erase-suspended. DQ6, by comparison, indicates whether the device is
actively erasing, or is in Erase Suspend, but cannot distinguish which sectors are selected for erasure. Thus,
both status bits are required for sector and mode information. Refer to Table 11.1 on page 43 to compare
outputs for DQ2 and DQ6.
Figure 11.2 on page 41 shows the toggle bit algorithm in flowchart form, and DQ2: Toggle Bit II on page 42
explains the algorithm. See also DQ6: Toggle Bit I on page 40. Figure 17.10 on page 54 shows the toggle bit
timing diagram. Figure 17.11 on page 55 shows the differences between DQ2 and DQ6 in graphical form.
11.5
Reading Toggle Bits DQ6/DQ2
Refer to Figure 11.2 on page 41 for the following discussion. Whenever the system initially begins reading
toggle bit status, it must read DQ15–DQ0 (or DQ7–DQ0 for x8-only device) at least twice in a row to
determine whether a toggle bit is toggling. Typically, the system would note and store the value of the toggle
bit after the first read. After the second read, the system would compare the new value of the toggle bit with
the first. If the toggle bit is not toggling, the device has completed the program or erase operation. The system
can read array data on DQ15–DQ0 (or DQ7–DQ0 for x8-only device) on the following read cycle.
However, if after the initial two read cycles, the system determines that the toggle bit is still toggling, the
system also should note whether the value of DQ5 is high (see the section on DQ5). If it is, the system should
then determine again whether the toggle bit is toggling, since the toggle bit may have stopped toggling just as
DQ5 went high. If the toggle bit is no longer toggling, the device has successfully completed the program or
erase operation. If it is still toggling, the device did not completed the operation successfully, and the system
must write the reset command to return to reading array data.
The remaining scenario is that the system initially determines that the toggle bit is toggling and DQ5 has not
gone high. The system may continue to monitor the toggle bit and DQ5 through successive read cycles,
determining the status as described in the previous paragraph. Alternatively, it may choose to perform other
system tasks. In this case, the system must start at the beginning of the algorithm when it returns to
determine the status of the operation (top of Figure 11.2 on page 41).
11.6
DQ5: Exceeded Timing Limits
DQ5 indicates whether the program or erase time has exceeded a specified internal pulse count limit. Under
these conditions DQ5 produces a “1,” indicating that the program or erase cycle was not successfully
completed.
The device may output a “1” on DQ5 if the system tries to program a “1” to a location that was previously
programmed to “0.” Only an erase operation can change a “0” back to a “1.” Under this condition, the
device halts the operation, and when the timing limit has been exceeded, DQ5 produces a “1.” The
RDY/BSY# pin will be in the BUSY state under this condition.
Under both these conditions, the system must write the reset command to return to the read mode (or to the
erase-suspend-read mode if a bank was previously in the erase-suspend-program mode).
42
S29JL032J
S29JL032J_00_06 December 16, 2011
D a t a
11.7
S h e e t
DQ3: Sector Erase Timer
After writing a sector erase command sequence, the system may read DQ3 to determine whether or not
erasure has begun. (The sector erase timer does not apply to the chip erase command.) If additional sectors
are selected for erasure, the entire time-out also applies after each additional sector erase command. When
the time-out period is complete, DQ3 switches from a “0” to a “1.” If the time between additional sector erase
commands from the system can be assumed to be less than 50 µs, the system need not monitor DQ3. See
also Sector Erase Command Sequence on page 35.
After the sector erase command is written, the system should read the status of DQ7 (Data# Polling) or DQ6
(Toggle Bit I) to ensure that the device has accepted the command sequence, and then read DQ3. If DQ3 is
“1,” the Embedded Erase algorithm has begun; all further commands (except Erase Suspend) are ignored
until the erase operation is complete. If DQ3 is “0,” the device will accept additional sector erase commands.
To ensure the command has been accepted, the system software should check the status of DQ3 prior to and
following each subsequent sector erase command. If DQ3 is high on the second status check, the last
command might not have been accepted.
Table 11.1 shows the status of DQ3 relative to the other status bits.
Table 11.1 Write Operation Status
DQ7
(Note 2)
DQ6
DQ5
(Note 1)
DQ3
DQ2
(Note 2)
RY/BY#
DQ7#
Toggle
0
N/A
No toggle
0
In busy erasing
sector
0
Toggle
0
1
Toggle
0
In not busy erasing
sector
0
Toggle
0
1
No toggle
0
Erase
Suspended Sector
1
No toggle
0
N/A
Toggle
1
Non-Erase
Suspended Sector
Data
Data
Data
Data
Data
1
DQ7#
Toggle
0
N/A
N/A
0
Status
Embedded Program Algorithm
Standard
Mode
Erase
Suspend
Mode
Embedded Erase
Algorithm
Erase-SuspendRead
Erase-Suspend-Program
Notes:
1. DQ5 switches to ‘1’ when an Embedded Program or Embedded Erase operation has exceeded the maximum timing limits. Refer to the
section on DQ5 for more information.
2. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection for further details.
3. When reading write operation status bits, the system must always provide the bank address where the Embedded Algorithm is in
progress. The device outputs array data if the system addresses a non-busy bank.
December 16, 2011 S29JL032J_00_06
S29JL032J
43
D a t a
S h e e t
12. Absolute Maximum Ratings
Storage Temperature, Plastic Packages
–65°C to +150°C
Ambient Temperature with Power Applied
–65°C to +125°C
Voltage with Respect to Ground, VCC (Note 1)
–0.5V to +4.0V
A9 and RESET# (Note 2)
–0.5V to +12.5V
WP#/ACC
–0.5V to +9.5V
All other pins (Note 1)
–0.5V to VCC +0.5V
Output Short Circuit Current (Note 3)
200 mA
Notes:
1. Minimum DC voltage on input or I/O pins is –0.5V. During voltage transitions, input or I/O pins may overshoot VSS to –2.0V for periods of
up to 20 ns. Maximum DC voltage on input or I/O pins is VCC +0.5V. See Figure 12.1 on page 44. During voltage transitions, input or I/O
pins may overshoot to VCC +2.0V for periods up to 20 ns. See Figure 12.2 on page 44.
2. Minimum DC input voltage on pins A9, OE#, RESET#, and WP#/ACC is –0.5V. During voltage transitions, A9, OE#, WP#/ACC, and
RESET# may overshoot VSS to –2.0V for periods of up to 20 ns. See Figure 12.1 on page 44. Maximum DC input voltage on pin A9 is
+12.5V which may overshoot to +14.0V for periods up to 20 ns. Maximum DC input voltage on WP#/ACC is +9.5V which may overshoot
to +12.0V for periods up to 20 ns.
3. No more than one output may be shorted to ground at a time. Duration of the short circuit should not be greater than one second.
4. Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only;
functional operation of the device at these or any other conditions above those indicated in the operational sections of this data sheet is
not implied. Exposure of the device to absolute maximum rating conditions for extended periods may affect device reliability.
Figure 12.1 Maximum Negative Overshoot Waveform
20 ns
20 ns
+0.8V
–0.5V
–2.0V
20 ns
Figure 12.2 Maximum Positive Overshoot Waveform
20 ns
VCC
+2.0V
VCC
+0.5V
2.0V
20 ns
44
S29JL032J
20 ns
S29JL032J_00_06 December 16, 2011
D a t a
S h e e t
13. Operating Ranges
Industrial (I) Devices
Ambient Temperature (TA)
–40°C to +85°C
VCC Supply Voltages
VCC for standard voltage range
2.7V to 3.6V
Operating ranges define those limits between which the functionality of the device is guaranteed.
14. DC Characteristics
14.1
CMOS Compatible
Parameter
Symbol
Parameter Description
Test Conditions
Min
Typ
Max
Unit
±1.0
µA
ILI
Input Load Current
VIN = VSS to VCC,
VCC = VCC max
ILIT
A9 and RESET# Input Load Current
VCC = VCC max, OE# = VIH;
A9 or RESET# = 12.5V
35
µA
ILO
Output Leakage Current
VOUT = VSS to VCC,
VCC = VCC max, OE# = VIH
±1.0
µA
ILR
Reset Leakage Current
VCC = VCC max; RESET# = 12.5V
35
µA
ICC1
VCC Active Read Current
(Notes 1, 2)
CE# = VIL, OE# = VIH,
Byte Mode
5 MHz
10
16
1 MHz
2
4
CE# = VIL, OE# = VIH,
Word Mode
5 MHz
10
16
mA
1 MHz
2
4
ICC2
VCC Active Write Current (Notes 2, 3)
CE# = VIL, OE# = VIH, WE# = VIL
15
30
ICC3
VCC Standby Current (Note 2)
CE#, RESET# = VCC ± 0.3V
0.2
5
µA
ICC4
VCC Reset Current (Note 2)
RESET# = VSS ± 0.3V
0.2
5
µA
ICC5
Automatic Sleep Mode (Notes 2, 4)
VIH = VCC ± 0.3V;
VIL = VSS ± 0.3V
0.2
5
µA
VCC Active Read-While-Program Current
(Note 2)
CE# = VIL, OE# = VIH,
1 MHz
Byte
21
45
ICC6
Word
21
45
VCC Active Read-While-Erase Current
(Note 2)
CE# = VIL, OE# = VIH,
Byte
21
45
ICC7
1 MHz
Word
21
45
ICC8
VCC Active Program-While-Erase-Suspended
Current (Notes 2, 5)
17
35
mA
mA
mA
CE# = VIL, OE# = VIH
mA
VIL
Input Low Voltage
–0.5
0.8
V
VIH
Input High Voltage
0.7 x VCC
VCC + 0.3
V
VHH
Voltage for WP#/ACC Sector Protect/
Unprotect and Program Acceleration
VCC = 3.0V ± 10%
8.5
9.5
V
VID
Voltage for Autoselect and Temporary Sector
Unprotect
VCC = 3.0V ± 10%
8.5
12.5
V
VOL
Output Low Voltage
IOL = 2.0 mA, VCC = VCC min
0.45
V
VOH1
Output High Voltage
VOH2
VLKO
IOH = –2.0 mA, VCC = VCC min
0.85 x VCC
IOH = –100 µA, VCC = VCC min
VCC–0.4
Low VCC Lock-Out Voltage (Note 5)
1.8
V
2.0
2.5
V
Notes:
1. The ICC current listed is typically less than 2 mA/MHz, with OE# at VIH.
2. Maximum ICC specifications are tested with VCC = VCCmax.
3. ICC active while Embedded Erase or Embedded Program is in progress.
4. Automatic sleep mode enables the low power mode when addresses remain stable for tACC + 30 ns. Typical sleep mode current is
200 nA.
5. Not 100% tested.
December 16, 2011 S29JL032J_00_06
S29JL032J
45
D a t a
14.2
S h e e t
Zero-Power Flash
Figure 14.1 ICC1 Current vs. Time (Showing Active and Automatic Sleep Currents)
Supply Current in mA
25
20
15
10
5
0
0
500
1000
1500
2000
2500
3000
3500
4000
Time in ns
Note:
Addresses are switching at 1 MHz
Figure 14.2 Typical ICC1 vs. Frequency
12
3.6V
10
2.7V
Supply Current in mA
8
6
4
2
0
1
2
3
4
5
Frequency in MHz
Note:
T = 25°C
46
S29JL032J
S29JL032J_00_06 December 16, 2011
D a t a
S h e e t
15. Test Conditions
Figure 15.1 Test Setup
Device
Under
Test
CL
Note:
Diodes are IN3064 or equivalent.
Table 15.1 Test Specifications
Test Condition
Output Load Capacitance, CL
60
70
Unit
30
100
pF
Input Rise and Fall Times (1)
Input Pulse Levels
5
ns
0.0 or Vcc
V
Input timing measurement reference levels
0.5 Vcc
V
Output timing measurement reference levels
0.5 Vcc
V
Note:
1. Input rise and fall times are 0-100%.
16. Key To Switching Waveforms
Waveform
Inputs
Outputs
Steady
Changing from H to L
Changing from L to H
Don’t Care, Any Change Permitted
Changing, State Unknown
Does Not Apply
Center Line is High Impedance State (High-Z)
Figure 16.1 Input Waveforms and Measurement Levels
Vcc
Input
0.5 Vcc
Measurement Level
0.5 Vcc
Output
0.0 V
December 16, 2011 S29JL032J_00_06
S29JL032J
47
D a t a
S h e e t
17. AC Characteristics
17.1
Read-Only Operations
Parameter
JEDEC
Std.
tAVAV
tRC
tAVQV
Speed Options
Description
Test Setup
Read Cycle Time (Note 1)
tACC
Address to Output Delay
CE#,
OE# = VIL
OE# = VIL
60
70
Unit
Min
60
70
ns
Max
60
70
ns
tELQV
tCE
Chip Enable to Output Delay
Max
60
70
ns
tGLQV
tOE
Output Enable to Output Delay
Max
25
30
ns
tEHQZ
tDF
Chip Enable to Output High-Z (Notes 1, 3)
Max
16
ns
tGHQZ
tDF
Output Enable to Output High-Z (Notes 1, 3)
Max
16
ns
tOH
Output Hold Time From Addresses, CE# or OE#,
Whichever Occurs First
Min
0
ns
Read
Min
0
ns
tOEH
Output Enable Hold Time
(Note 1)
Toggle and
Data# Polling
Min
tAXQX
5
10
ns
Notes:
1. Not 100% tested.
2. See Figure 15.1 on page 47 and Table 15.1 on page 47 for test specifications
3. Measurements performed by placing a 50 ohm termination on the data pin with a bias of VCC/2. The time from OE# high to the data bus
driven to VCC/2 is taken as tDF.
Figure 17.1 Read Operation Timings
tRC
Addresses Stable
Addresses
tACC
CE#
tRH
tRH
tDF
tOE
OE#
tOEH
WE#
tCE
tOH
HIGH-Z
HIGH-Z
Output Valid
Outputs
RESET#
RY/BY#
48
0V
S29JL032J
S29JL032J_00_06 December 16, 2011
D a t a
17.2
S h e e t
Hardware Reset (RESET#)
Parameter
JEDEC
Std
Description
tReady
RESET# Pin Low (During Embedded Algorithms) to Read Mode
(See Note)
tReady
RESET# Pin Low (NOT During Embedded Algorithms) to Read
Mode (See Note)
All Speed Options
Unit
Max
35
µs
Max
500
ns
tRP
RESET# Pulse Width
Min
500
ns
tRH
Reset High Time Before Read (See Note)
Min
50
ns
tRPD
RESET# Low to Standby Mode
Min
35
µs
tRB
RY/BY# Recovery Time
Min
0
ns
Note:
Not 100% tested.
Figure 17.2 Reset Timings
RY/BY#
CE#, OE#
tRH
RESET#
tRP
tReady
Reset Timings NOT during Embedded Algorithms
Reset Timings during Embedded Algorithms
tReady
RY/BY#
tRB
CE#, OE#
RESET#
tRP
December 16, 2011 S29JL032J_00_06
S29JL032J
49
D a t a
17.3
S h e e t
Word/Byte Configuration (BYTE#)
Speed Options
Parameter
JEDEC
Std.
Description
tELFL/tELFH
60
70
CE# to BYTE# Switching Low or High
Max
5
tFLQZ
BYTE# Switching Low to Output HIGH-Z
Max
16
tFHQV
BYTE# Switching High to Output Active
Max
60
Unit
ns
ns
70
ns
Figure 17.3 BYTE# Timings for Read Operations
CE#
OE#
BYTE#
tELFL
BYTE#
Switching
from word
to byte
mode
Data Output
(DQ7–DQ0)
Data Output
(DQ14–DQ0)
DQ14–DQ0
Address
Input
DQ15
Output
DQ15/A-1
tFLQZ
tELFH
BYTE#
BYTE#
Switching
from byte to
word mode
Data Output
(DQ14–DQ0)
Data Output
(DQ7–DQ0)
DQ14–DQ0
Address
Input
DQ15/A-1
DQ15
Output
tFHQV
Figure 17.4 BYTE# Timings for Write Operations
CE#
The falling edge of the last WE# signal
WE#
BYTE#
tSET
(tAS)
tHOLD (tAH)
Note:
Refer to the table in Erase and Program Operations on page 51 for tAS and tAH specifications.
50
S29JL032J
S29JL032J_00_06 December 16, 2011
D a t a
17.4
S h e e t
Erase and Program Operations
Parameter
Speed Options
JEDEC
Std
Description
tAVAV
tWC
Write Cycle Time (Note 1)
Min
tAS
60
70
Unit
60
70
ns
Address Setup Time
Min
0
tASO
Address Setup Time to OE# low during toggle bit polling
Min
12
tAH
Address Hold Time
Min
tAHT
Address Hold Time From CE# or OE# high
during toggle bit polling
Min
tDVWH
tDS
Data Setup Time
Min
tWHDX
tDH
Data Hold Time
Min
0
ns
tOEPH
Output Enable High during toggle bit polling
Min
20
ns
tGHWL
Read Recovery Time Before Write
(OE# High to WE# Low)
Min
0
ns
ns
tAVWL
tWLAX
tGHWL
35
ns
ns
35
0
35
ns
ns
40
ns
tELWL
tCS
CE# Setup Time
Min
0
tWHEH
tCH
CE# Hold Time
Min
0
tWLWH
tWP
Write Pulse Width
Min
25
30
ns
tWHDL
tWPH
Write Pulse Width High
Min
25
30
ns
tSR/W
Latency Between Read and Write Operations
tWHWH1
tWHWH1
Programming Operation (Note 2)
tWHWH1
tWHWH1
Accelerated Programming Operation,
Byte or Word (Note 2)
tWHWH2
tWHWH2
ns
Min
0
Byte
Typ
6
ns
Word
Typ
6
Typ
4
µs
µs
Sector Erase Operation (Note 2)
Typ
0.5
sec
tVCS
VCC Setup Time (Note 1)
Min
50
µs
tRB
Write Recovery Time from RY/BY#
Min
0
ns
Program/Erase Valid to RY/BY# Delay
Max
90
ns
Erase Suspend Latency
Max
35
µs
tBUSY
tESL
Notes:
1. Not 100% tested.
2. See Erase and Programming Performance on page 58 for more information.
December 16, 2011 S29JL032J_00_06
S29JL032J
51
D a t a
S h e e t
Figure 17.5 Program Operation Timings
Program Command Sequence (last two cycles)
tAS
tWC
Addresses
Read Status Data (last two cycles)
555h
PA
PA
PA
tAH
CE#
tCH
OE#
tWHWH1
tWP
WE#
tWPH
tCS
tDS
tDH
PD
A0h
Data
Status
tBUSY
DOUT
tRB
RY/BY#
VCC
tVCS
Notes:
1. PA = program address, PD = program data, DOUT is the true data at the program address.
2. Illustration shows device in word mode.
Figure 17.6 Accelerated Program Timing Diagram
VHH
WP#/ACC
VIL or VIH
VIL or VIH
tVHH
52
tVHH
S29JL032J
S29JL032J_00_06 December 16, 2011
D a t a
S h e e t
Figure 17.7 Chip/Sector Erase Operation Timings
Erase Command Sequence (last two cycles)
tAS
tWC
2AAh
Addresses
Read Status Data
VA
SA
VA
555h for chip erase
tAH
CE#
tCH
OE#
tWP
WE#
tWPH
tCS
tWHWH2
tDS
tDH
Data
55h
In
Progress
30h
Complete
10 for Chip Erase
tBUSY
tRB
RY/BY#
tVCS
VCC
Notes:
1. SA = sector address (for Sector Erase), VA = Valid Address for reading status data (see Write Operation Status on page 39).
2. These waveforms are for the word mode.
Figure 17.8 Back-to-back Read/Write Cycle Timings
Addresses
tWC
tWC
tRC
Valid PA
Valid RA
tWC
Valid PA
Valid PA
tAH
tCPH
tACC
tCE
CE#
tCP
tOE
OE#
tOEH
tGHWL
tWP
WE#
tWPH
tDF
tDS
tOH
tDH
Data
Valid
Out
Valid
In
Valid
In
Valid
In
tSR/W
WE# Controlled Write Cycle
December 16, 2011 S29JL032J_00_06
Read Cycle
S29JL032J
CE# or CE2# Controlled Write Cycles
53
D a t a
S h e e t
Figure 17.9 Data# Polling Timings (During Embedded Algorithms)
tRC
Addresses
VA
VA
VA
tACC
tCE
CE#
tCH
tOE
OE
tOEH
WE#
tDF
tOH
DQ7
DQ0–DQ6
Complement
Compleme
Status
Status
Valid Data
Tru
Valid Data
Tru
High-Z
High-Z
tBUSY
RY/BY#
Note:
VA = Valid address. Illustration shows first status cycle after command sequence, last status read cycle, and array data read cycle.
Figure 17.10 Toggle Bit Timings (During Embedded Algorithms)
tAHT
tAS
Addresses
tAHT
tASO
CE#
tCPH
tOEH
WE#
tOEPH
OE#
tDH
DQ6/DQ2
Valid Data
tOE
Valid
Status
Valid
Status
Valid
Status
(first read)
(second read)
(stops toggling)
Valid Data
RY/BY#
Note:
VA = Valid address; not required for DQ6. Illustration shows first two status cycle after command sequence, last status read cycle, and array data read cycle.
54
S29JL032J
S29JL032J_00_06 December 16, 2011
D a t a
S h e e t
Figure 17.11 DQ2 vs. DQ6
Enter
Embedded
Erasing
WE#
Erase
Suspend
Erase
Enter Erase
Suspend Program
Erase Suspend
Read
Erase
Suspend
Program
Erase
Resume
Erase Suspend
Read
Erase
Complete
Erase
DQ6
DQ2
Note:
DQ2 toggles only when read at an address within an erase-suspended sector. The system may use OE# or CE# to toggle DQ2 and DQ6.
17.5
Temporary Sector Unprotect
Parameter
JEDEC
Std
Description
All Speed Options
Unit
tVIDR
VID Rise and Fall Time (See Note)
Min
500
ns
tVHH
VHH Rise and Fall Time (See Note)
Min
250
ns
tRSP
RESET# Setup Time for Temporary Sector Unprotect
Min
4
µs
tRRB
RESET# Hold Time from RY/BY# High for Temporary
Sector Unprotect
Min
4
µs
Note:
Not 100% tested.
Figure 17.12 Temporary Sector Unprotect Timing Diagram
VID
RESET#
VID
VSS, VIL,
or VIH
VSS, VIL,
or VIH
tVIDR
tVIDR
Program or Erase Command Sequence
CE#
WE#
tRRB
tRSP
RY/BY#
December 16, 2011 S29JL032J_00_06
S29JL032J
55
D a t a
S h e e t
Figure 17.13 Sector/Sector Block Protect and Unprotect Timing Diagram
VID
VIH
RESET#
SA, A6,
A1, A0
Valid*
Valid*
Sector Group Protect/Unprotect
Data
60h
Valid*
Verify
60h
40h
Status
1 µs
Sector Group Protect: 150 µs
Sector Group Unprotect: 15 ms
CE#
WE#
OE#
Note:
*For sector protect, A6 = 0, A1 = 1, A0 = 0. For sector unprotect, A6 = 1, A1 = 1, A0 = 0
17.6
Alternate CE# Controlled Erase and Program Operations
Speed Options
Parameter
JEDEC
Std.
Description
tAVAV
tWC
Write Cycle Time (Note 1)
Min
tAVWL
tAS
Address Setup Time
Min
60
70
Unit
60
70
ns
ns
0
tELAX
tAH
Address Hold Time
Min
35
35
tDVEH
tDS
Data Setup Time
Min
30
30
tEHDX
tDH
Data Hold Time
Min
0
ns
tGHEL
tGHEL
Read Recovery Time Before Write
(OE# High to WE# Low)
Min
0
ns
tWLEL
tWS
WE# Setup Time
Min
0
ns
tEHWH
tWH
WE# Hold Time
Min
tELEH
tCP
CE# Pulse Width
Min
25
35
ns
tEHEL
tCPH
CE# Pulse Width High
Min
25
30
ns
0
Byte
Typ
6
Word
Typ
6
ns
ns
ns
tWHWH1
tWHWH1
Programming Operation
(Note 2)
tWHWH1
tWHWH1
Accelerated Programming Operation,
Byte or Word (Note 2)
Typ
4
µs
tWHWH2
tWHWH2
Sector Erase Operation (Note 2)
Typ
0.5
sec
µs
Notes:
1. Not 100% tested.
2. See Erase and Programming Performance on page 58 for more information.
56
S29JL032J
S29JL032J_00_06 December 16, 2011
D a t a
S h e e t
Figure 17.14 Alternate CE# Controlled Write (Erase/Program) Operation Timings
555 for program
2AA for erase
PA for program
SA for sector erase
555 for chip erase
Data# Polling
Addresses
PA
tWC
tAS
tAH
tWH
WE#
tGHEL
OE#
tWHWH1 or 2
tCP
CE#
tWS
tCPH
tBUSY
tDS
tDH
DQ7#
Data
tRH
A0 for program
55 for erase
DOUT
PD for program
30 for sector erase
10 for chip erase
RESET#
RY/BY#
Notes:
1. Figure indicates last two bus cycles of a program or erase operation.
2. PA = program address, SA = sector address, PD = program data.
3. DQ7# is the complement of the data written to the device. DOUT is the data written to the device.
4. Waveforms are for the word mode.
December 16, 2011 S29JL032J_00_06
S29JL032J
57
D a t a
S h e e t
18. Erase and Programming Performance
Parameter
Typ (Note 1)
Max (Note 2)
Unit
Comments
5
sec
Excludes 00h programming
prior to erasure (Note 3)
Sector Erase Time
0.5
Chip Erase Time
39
Byte Program Time
6
80
µs
Word Program Time
6
80
µs
Accelerated Byte/Word Program Time
4
70
µs
sec
Excludes system level
overhead (Note 4)
Notes:
1. Typical program and erase times assume the following conditions: 25°C, VCC = 3.0V, 100,000 cycles; checkerboard data pattern.
2. Under worst case conditions of 90°C, VCC = 2.7V, 1,000,000 cycles.
3. In the pre-programming step of the Embedded Erase algorithm, all bytes are programmed to 00h before erasure.
4. System-level overhead is the time required to execute the two- or four-bus-cycle sequence for the program command. See Table 10.1
on page 38 for further information on command definitions.
5. The device has a minimum program and erase cycle endurance of 100,000 cycles per sector.
19. Pin Capacitance
Parameter Symbol
Parameter Description
Test Setup
Max
CIN
Input Capacitance (applies to A20-A0, DQ15-DQ0)
VIN = 0
8.5
Unit
pF
COUT
Output Capacitance (applies to DQ15-DQ0, RY/BY#)
VOUT = 0
5.5
pF
CIN2
Control Pin Capacitance
(applies to CE#, WE#, OE#, WP#/ACC, RESET#, BYTE#)
VIN = 0
12
pF
Notes:
1. Sampled, not 100% tested.
2. Test conditions TA = 25°C, f = 1.0 MHz.
58
S29JL032J
S29JL032J_00_06 December 16, 2011
D a t a
S h e e t
20. Physical Dimensions
20.1
TS 048—48-Pin Standard TSOP
PACKAGE
TS/TSR 48
JEDEC
MO-142 (D) DD
SYMBOL
NOTES:
MIN
NOM
MAX
A
---
---
1.20
A1
0.05
---
0.15
A2
0.95
1.00
1.05
b1
0.17
0.20
0.23
b
0.17
0.22
0.27
c1
0.10
---
0.16
c
0.10
---
0.21
D
19.80
20.00
20.20
D1
18.30
18.40
18.50
E
11.90
12.00
12.10
e
0.50 BASIC
L
0.50
0.60
0.70
Θ
0˚
---
8
R
0.08
---
0.20
N
December 16, 2011 S29JL032J_00_06
1.
CONTROLLING DIMENSIONS ARE IN MILLIMETERS (mm).
(DIMENSIONING AND TOLERANCING CONFORM TO ANSI Y14.5M-1982)
2.
PIN 1 IDENTIFIER FOR STANDARD PIN OUT (DIE UP).
3.
PIN 1 IDENTIFIER FOR REVERSE PIN OUT (DIE DOWN): INK OR LASER MARK.
4.
TO BE DETERMINED AT THE SEATING PLANE -C- . THE SEATING PLANE IS
DEFINED AS THE PLANE OF CONTACT THAT IS MADE WHEN THE PACKAGE LEADS
ARE ALLOWED TO REST FREELY ON A FLAT HORIZONTAL SURFACE.
5.
DIMENSIONS D1 AND E DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE MOLD
PROTUSION IS 0.15mm (.0059") PER SIDE.
6.
DIMENSION b DOES NOT INCLUDE DAMBAR PROTUSION. ALLOWABLE DAMBAR
PROTUSION SHALL BE 0.08mm (0.0031") TOTAL IN EXCESS OF b DIMENSION AT MAX.
MATERIAL CONDITION. MINIMUM SPACE BETWEEN PROTRUSION AND AN ADJACENT
LEAD TO BE 0.07mm (0.0028").
7.
THESE DIMENSIONS APPLY TO THE FLAT SECTION OF THE LEAD BETWEEN
0.10mm (.0039") AND 0.25mm (0.0098") FROM THE LEAD TIP.
8.
LEAD COPLANARITY SHALL BE WITHIN 0.10mm (0.004") AS MEASURED FROM
THE SEATING PLANE.
9.
DIMENSION "e" IS MEASURED AT THE CENTERLINE OF THE LEADS.
48
3664 \ f16-038.10 \ 11.6.7
S29JL032J
59
D a t a
20.2
S h e e t
VBK048—48-Pin FBGA
NOTES:
PACKAGE
VBK 048
JEDEC
N/A
8.15 mm x 6.15 mm NOM
PACKAGE
SYMBOL
1.
DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3.
BALL POSITION DESIGNATION PER JESD 95-1, SPP-010 (EXCEPT
AS NOTED).
MIN
NOM
MAX
NOTE
4.
e REPRESENTS THE SOLDER BALL GRID PITCH.
A
---
---
1.00
OVERALL THICKNESS
5.
A1
0.18
---
---
SYMBOL "MD" IS THE BALL ROW MATRIX SIZE IN THE
"D" DIRECTION.
BALL HEIGHT
D
8.15 BSC.
BODY SIZE
E
6.15 BSC.
BODY SIZE
D1
5.60 BSC.
BALL FOOTPRINT
E1
4.00 BSC.
BALL FOOTPRINT
MD
8
ROW MATRIX SIZE D DIRECTION
ME
6
ROW MATRIX SIZE E DIRECTION
N
φb
48
0.33
---
N IS THE TOTAL NUMBER OF SOLDER BALLS.
6
DIMENSION "b" IS MEASURED AT THE MAXIMUM BALL
DIAMETER IN A PLANE PARALLEL TO DATUM C.
7
SD AND SE ARE MEASURED WITH RESPECT TO DATUMS
A AND B AND DEFINE THE POSITION OF THE CENTER
SOLDER BALL IN THE OUTER ROW.
TOTAL BALL COUNT
0.43
WHEN THERE IS AN ODD NUMBER OF SOLDER BALLS IN
THE OUTER ROW PARALLEL TO THE D OR E DIMENSION,
RESPECTIVELY, SD OR SE = 0.000.
BALL DIAMETER
e
0.80 BSC.
BALL PITCH
SD / SE
0.40 BSC.
SOLDER BALL PLACEMENT
---
SYMBOL "ME" IS THE BALL COLUMN MATRIX SIZE IN THE
"E" DIRECTION.
WHEN THERE IS AN EVEN NUMBER OF SOLDER BALLS IN
THE OUTER ROW, SD OR SE = e/2
DEPOPULATED SOLDER BALLS
8.
NOT USED.
9.
"+" INDICATES THE THEORETICAL CENTER OF DEPOPULATED
BALLS.
10
A1 CORNER TO BE IDENTIFIED BY CHAMFER, LASER OR INK
MARK, METALLIZED MARK INDENTATION OR OTHER MEANS.
g1001.2 \ f16-038.25 \ 07.13.10
60
S29JL032J
S29JL032J_00_06 December 16, 2011
D a t a
S h e e t
21. Revision History
Section
Description
Revision 01 (January 27, 2010)
Initial release.
Revision 02 (June 15, 2010)
Changed all references to typical Sector Erase time from 0.4 sec to 0.5 sec.
Global
Changed all references to “Secured Silicon Sector” to “Secured Silicon Region”.
Product Selector Guide
Corrected Standard Voltage Range of 70 ns option from 3.0-3.6V to 2.7-3.6V.
Corrected spelling and grammatical errors.
Connection Diagrams
Pin Description
Added 48-ball FBGA connection diagram.
Changes “21 Addresses” to “21 Address Pins”.
Added clarification that CE#, OE#, WE#, BYTE#, and RY/BY# are Active Low.
Added FBGA ordering option.
Ordering Information
Added Low-halogen, Pb-free ordering option.
Word/Byte Configuration
Added clarification that BYTE# must be connected to either the system VCC or ground.
Added valid combinations for FBGA.
Added clarification that D7 is the Secured Silicon Factory Indicator Bit.
Secured Silicon Region
In Figure Secured Silicon Sector Protect Verify, corrected “Write reset command” to “Secured
Silicon Region exit command”.
Command Definitions
Corrected “Writing specific addresses and data commands or sequences” to “Writing specific
addresses and data sequences”.
Absolute Maximum Ratings
Corrected “A9, OE#, and RESET#” to “A9 and RESET#”.
Removed OE# from ILIT parameter description.
DC Characteristics
Removed OE# = 12.5V from ILIT test conditions.
Added 1 MHz to ICC6 and ICC7 test conditions.
Removed Note 1 from ICC6 and ICC7.
Test Conditions
Erase and Programming Performance
Physical Dimensions
Update Figure “Test Setup” to reflect correct test setup.
Added Note 1 to clarify that input rise and fall times are 0-100%.
Changed Chip Erase typical time from 28 sec to 39 sec.
Removed Note 5.
Added VBK048 package outline drawing.
Revision 03 (August 25, 2010)
Global
Simultaneous Read/Write Operations
with Zero Latency
Ordering Information
RESET#: Hardware Reset Pin
Updated the data sheet designation from Advanced Information to Preliminary.
Corrected spelling, capitalization, and grammatical errors.
Clarified that JL032J can be configured as either a top or bottom boot sector device, not both.
Corrected typo in valid combinations table from “…, 41, 41” to “…, 41, 42”.
Clarified that Note 1 applies to the Packing Type column.
Changed “Refer to AC Characteristics on page 48” to “Refer to Hardware Reset (RESET#) on page
49”.
Clarified the Secured Silicon Indicator Bit data based on factory and customer lock status.
Secured Silicon Region
Removed forward looking statements regarding factory locking features as they are supported in
this device.
Common Flash Memory Interface (CFI)
Clarified that once in the CFI query mode, the system must write the reset command to return to
reading array data.
Erase Suspend/Erase Resume
Commands
Added clarification that “It is not recommended to program the Secured Silicon Region after an
erase suspend, as proper device functionality cannot be guaranteed.”
Erase and Programming Performance
Added Note 5 regarding minimum program and erase cycle endurance.
December 16, 2011 S29JL032J_00_06
S29JL032J
61
D a t a
Section
S h e e t
Description
Changed section title from "TSOP Pin Capacitance" to "Pin Capacitance".
Pin Capacitance
Updated values to reflect maximum capacitances for both TSOP and BGA.
Removed typical capacitance values.
Added specific pin clarifications to parameter descriptions.
Physical Dimensions
Updated the VBK048 package outline drawing.
Revision 04 (April 7, 2011)
Global
Updated the data sheet designation from Preliminary to Full Production (no designation on
document).
Distinctive Characteristics
Corrected "Top and bottom boot sectors in the same device" to "Top and bottom boot sector
configurations available".
RESET#: Hardware Reset Pin
Added warning that keeping CE# at VIL from power up through the first reset could cause
erroneuous data on the first read.
Reset Command
Clarified that during an embedded program or erase, if DQ5 goes high then RY/BY# will remain low
until a reset is issued.
Hardware Reset (RESET#)
Added note to the “Reset Timings” figure clarifying that CE# should only go low after RESET# has
gone high.
Revision 05 (August 24, 2011)
RESET#: Hardware Reset Pin
Removed warning that keeping CE# at VIL from power up through the first reset could cause
erroneuous data on the first read.
Command Definitions Table
Added Note 17 to clarify additional sector erase commands during time-out period.
Sector Erase Command Sequence
Added clarification regarding additional sector erase commands during time-out period.
Hardware Reset (RESET#)
Removed note to the “Reset Timings” figure clarifying that CE# should only go low after RESET#
has gone high.
Physical Dimensions
Package drawings updated to latest version.
Revision 06 (December 16, 2011)
Global
Corrected all references in the text to the sector erase time-out period from 80 µs to 50 µs.
Word/Byte Configuration
Removed the statement “Please note that the BYTE# pin must be connected to either the system
VCC or ground.”
62
S29JL032J
S29JL032J_00_06 December 16, 2011
D a t a
S h e e t
Colophon
The products described in this document are designed, developed and manufactured as contemplated for general use, including without
limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as
contemplated (1) for any use that includes fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the
public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility,
aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for
any use where chance of failure is intolerable (i.e., submersible repeater and artificial satellite). Please note that Spansion will not be liable to
you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor
devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design
measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal
operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under
the Foreign Exchange and Foreign Trade Law of Japan, the US Export Administration Regulations or the applicable laws of any other country,
the prior authorization by the respective government entity will be required for export of those products.
Trademarks and Notice
The contents of this document are subject to change without notice. This document may contain information on a Spansion product under
development by Spansion. Spansion reserves the right to change or discontinue work on any product without notice. The information in this
document is provided as is without warranty or guarantee of any kind as to its accuracy, completeness, operability, fitness for particular purpose,
merchantability, non-infringement of third-party rights, or any other warranty, express, implied, or statutory. Spansion assumes no liability for any
damages of any kind arising out of the use of the information in this document.
Copyright © 2010-2011 Spansion Inc. All rights reserved. Spansion®, the Spansion logo, MirrorBit®, MirrorBit® Eclipse™, ORNAND™,
EcoRAM™ and combinations thereof, are trademarks and registered trademarks of Spansion LLC in the United States and other countries.
Other names used are for informational purposes only and may be trademarks of their respective owners.
December 16, 2011 S29JL032J_00_06
S29JL032J
63