Crystal oscillator TEMPERATURE COMPENSATED CRYSTAL OSCILLATOR TG-2832CB / 2833CB Products number (please refer to page 2) Q 3 7 0 5 C B 0 x xxx x00 Q 3 7 0 6 C B 0 x xxx x00 • Developed for Suited for wireless communication equipment (Low noise level: -120 dBc/Hz Typ. at 100 Hz offset, fo = 19.68 MHz) • Power saving function (standby function)built-in. (TG-2832CB) • Reflowable and high density mounting type ultra small size SMD. (5.0x3.2x1.5 mm) • Using the heat-resisting type AT cut quartz crystal allows almost the same temprature soldering as universal SMD IC. • Operating supply voltage : 2.8 V. Actual size Specifications Item Specifications Symbol Output frequency range TG-2832CB 16.0000 MHz to 26.0000 MHz Standard : 16.3670, 19.2000, 19.4400, 19.6800, 19.8000, 26.000 MHz 16 MHz ≤ fo ≤ 19 MHz : No frequency control function VCC TSTG TOPR ∆f0 -0.3 V to +6.0 V 2.8 V ±0.14 V -40 °C to +85 °C -30 °C to +80 °C ±1.5 x 10-6 Max. Stored as bare product after unpacking ∆fT ±2.5 x 10 Max. -30 °C to +80 °C (reference at +25 °C) ∆fL ±0.2 x 10-6 Max. 10 kΩ//10 pF ± 10% ∆fV ±0.3 x 10-6 Max. 2.8 V ±5 % fa ±1 x 10 Max. Ta=+25 °C,first year VCC=2.8 V, 10 kΩ//10 pF 19.68 MHz,STBY=VCC VCC=2.8 V, 10 kΩ//10 pF 19.68 MHz,STBY=GND (DC cut) VC-GND(DC), VC=1.4 V VC=1.4 V ±1.0 V, 19 MHz < fo ≤ 26 MHz 16 MHz ≤ fo ≤ 19 MHz : No frequency control function f0 Power source Max. supply voltage Operating voltage voltage Storage temperature Temperature Operating temperature range Frequency tolelance Frequency stability vs.temperature Frequency stability vs.load Frequency stability vs. supply voltage Aging Remarks TG-2833CB VCC-GND VC=1.4 V, +25 °C ±2 °C -6 -6 2.0 mA Max. Supply current lCC 50 µA Max. – Input resistance ZIN 800 kΩ Min. Frequency control range ∆fC 7 x 10-6 Min. Frequency change polarity Duty Output level Positive polarity 40 % to 60 % Duty VOUT RL CL Output load GND level (DC cut) 0.8 V Min. 9 kΩ to 11 kΩ 9 pF to 11 pF Peak to peak DC cut capacitor = 0.01 µF Note:Please contact us for inquiries about specifications other than the above. TG-2833CB #3 0.8 Recommended soldering pattern TG-2832CB #1 1 2 3 4 5 6 Pin terminal VC NC GND OUT STBY VCC 5.0±0.2 0.8 1.1 #1 #2 NO. 1 2 3 4 TG-2833CB 1.3 2.4 1.0 1.3 1.95 3.9 3.9 69 Pin terminal VC GND OUT VCC (Unit: mm) 1.0 1.0 #2 #4 1.4 0.8 1.4 3.2±0.2 NO. 1.1 E 19.680 Y9A1D 2.6 #3 3.2±0.2 #6 2.4 5.0±0.2 2.6 #4 #5 1.5 Max. E 19.680 G9A1D (Unit: mm) 1.5 Max. External dimensions TG-2832CB Do not design any patterns except GND on the shaded area. Except for this recommended soldering pattern, please contact us for inquiries.