S/MOT/SW960330/A/16/03/2000 page 1 /5 F/GB INVERSEURS DE SENS DE ROTATION MOTOR REVERSER ( Ready to use) SW960330 3x400VAC 1,5KW Le relais SW960330 est étudié pour démarrer et inverser le sens de rotation de moteurs triphasés asynchrones , avec la commutation de 2 phases uniquement ( 4 commutateurs : 2 legs) . Le produit directement montable sur rail DIN avec un calibre des thyristors de 50ARMS , permet de contrôler un moteur avec un courant nominal de 4,5ARMS soit 1,5kWatts sous 400VAC , en tenant compte des courants de démarrage et d'inversion. Ces produits sont réalisés avec des composants haute immunité , sans relais REED ( tout électronique) , avec toutes les protections : RC , VDR,... mais aussi intervérouillage , temporisation entre chaque inversion,... Ces relais sont équipés de thyristors 1600V. Boitier IP20 IP20 housing The relay SW960330 is designed for controlling and inverting the direction of a three-phase motors without direct third leg ( two legs). Directly mounting on a DIN rail , this product with a maximum current of semiconductors of 50 Amps. rms , can drive a motor with a current rating of 4,5 Amps.rms (or approximately 1,5kW under 400 V), taking the starting and reversing current into account. These products are designed with very high immunity components , without REED switches (only composed of solid state components) , with all protections : RC , VDR ,..... temporisation ,........., and 1600Volt peak voltage components. Proud to serve you All technical caracteristics are subject to change without previous notice. Caractéristiques sujettes à modifications sans préavis. ® celduc r e l a i s S/MOT/SW960330/A/16/03/2000 page 2 / 5 F/GB Synoptique interne / Internal diagram for two leg models : Control Développé conformément aux normes / Designed in compliance with standards: ->EN60947-4-2 (V.D.E. 0660 part 109, I.E.C. 158-2) ->EN60947-1 & A11 ->EN60950 (V.D.E. 0805-> office equipment) (Pending approval) ->U.L. 508 (Pending approval) ->c.U.L (Pending approval) Uc Ic Ur Plage de tension de commande / Control voltage range Plage de courant de commande / Control current range Tension de non fonctionnement/ Release voltage LED de visualisation / Display LED 12-30VDC 15-25mADC 6VDC Yes Yes 30V no output protection en cas de cdes simultanées / protection against simultaneous controls Urv tension inverse maxi / Maximum reverse voltage Signal de sortie / Output signal Unit Caractéristiques d'entrée-sortie (à 20°C) / Input-output characteristics (at 20°C) Isolement entrée-sortie/Input-output isolation @500m Ui 3300 VRMS Isolement sortie-semelle/Output-case isolation @500m Ui 3300 VRMS Uimp 4000 V Tension assignée isolement/rated impulse voltage 130g Unit g Plage de température de stockage / Storage temperature range -40 / +100 °C Plage de température de fonctionnement/Operating temperature range -40 / +100 °C Caractéristiques générales / General characteristics Poids/Weight ® celduc www.celduc.com r e l a i s 5, Rue Ampère BP30004 42290 SORBIERS - FRANCE E-mail : [email protected] Fax +33 (0) 4 77 53 85 51 Service Commercial France Tél. : +33 (0) 4 77 53 90 20 Sales Dept.For Europe Tel. : +33 (0) 4 77 53 90 21 Sales Dept. Asia : Tél. +33 (0) 4 77 53 90 19 S/MOT/SW960330/A/16/03/2000 E.M.C. Output page 3 / 5 F/GB Tension nominale/ Standard mains voltage Plage de tension de fonctionnement / Mains voltage range tension crête non répétitive/ Non-repetitive maximum peak voltage Courant AC-53 maxi/ Max. nom. current (AC53a=AC3) @40°C Puissance moteur/ 3 pole power motor ( 3x400VAC) Chute directe / Max Direct voltage drop (@Ie) Courant crête non répétitif/ Non repetitive overload current (@ 1 cycle of 10ms) I2t value/ Melting limit (choice of fuse) @10ms Courant minimal de charge / Minimum load current facteur de puissance/ Power factor (@ Ie) Ue Un Up Ie Pn Ud 400 VAC 24-520VAC 1600V 4,5ARMS 1,5KW 1,4VRMS ITSM 550A I2t Imin Pf Temps d'ouverture et de temporisation/ Turn on time-reversing time(@50Hz) ton/trv toff Temps d'ouverture/ Turn off time (@50Hz) Ilk Courant de fuite /Maximum leakage current (@Ue/50Hz) 4KV direct at output, 4KV with a clamp at input no turn on or damage 2KV in common mode, 1KV in differential mode (Input & output) no turn on or damage Max conducted immunity level Test accord. to I.E.C.1000-4-4 (bursts) Max conducted immunity level Test acc. to I.E.C.1000-4-5 (el. shocks) Max radiated immunity level Test accord. to I.E.C.1000-4-3 Max electrostatic disch. immunity level Test accord. to I.E.C.1000-4-2 Max conducted emission level (0,8<Pf<1) Test according to EN55011 Max radiated emission level Test accord. to EN55011 @Ie 10V/m no turn on or damage 8KV in the air / 4KV touching no turn on or damage The conducted noise made by SSR depends on the wiring configuration and the load type. Test methods recommended by European E.M.C. standards giving results far from reality, we have chosen to advise the right filter suited for the customer's use: Refer to EMC chapter <30dBµV from 30 up to 230MHz ; <37dBµV from 230 up to 1000MHz Base/junction thermal resistance Rthjc Ambient/junction thermal resistance Rthja (relay mounted vertically) Weight Characteristics given at 25°C unless otherwise specified Misc. 1500 A2s 100 mA 0 up to 1 20ms / 100ms 10ms 5 mARMS 0,5K/W (1 leg) ® celduc 5K/W 130g www.celduc.com REVERSERS + HEATSINK SELECTION IN COMPLIANCE WITH EN60947-4-2 Ferraz fuse type14x51 size / Overload relay type Relays with heatsink SSR SELECTION motors soft-staters max. rating Klöckner-Moeller am 8A/500V Z00-2.4 SW960330 am 8A/500V Z00-6 SW960330 am 12A/500V Z00-6 for a permanent current Motor power In motor (@ 400V) 0,75 kW 1,1 kW 1,5 kW 2,2 kW 3 kW 4 kW 2A 2,6A 3,5A 5A 6,6A 8,5A two legs ambient =40°C SW960330 SW961230 (See data-sheet) am 12A/500V Z00-6 SW961230 (See data-sheet) am 12A/500V Z00-10 SW961230 (See data-sheet) am 12A/500V Z00-10 For motor > 4kW consult us : we have some solutions ® celduc www.celduc.com r e l a i s 5, Rue Ampère BP30004 42290 SORBIERS - FRANCE E-mail : [email protected] Fax +33 (0) 4 77 53 85 51 Service Commercial France Tél. : +33 (0) 4 77 53 90 20 Sales Dept.For Europe Tel. : +33 (0) 4 77 53 90 21 Sales Dept. Asia : Tél. +33 (0) 4 77 53 90 19 S/MOT/SW960330/A/16/03/2000 Caractéristiques thermiques / Thermal curves : page 4 / 5 F/GB Courant de surcharge non repetitif :ITSM / Non repetitive surge peak onstate current : ITSM 1 : No repetitive Itsm (Apeak)=f(t) without voltage reapplied 2 : Repetitive Itsm (Apeak)=f(t) with voltage reapplied for initial Tj =70°C SV Wiring of the control circuit: NUMBER OF WIRES 1 SOLID (No ferrule) SCREWDRIVER TYPE MINIMUM TORQUE 2 (DISTRIBUTION) FINE STRANDED (With ferrule) SOLID (No ferrule) FINE STRANDED (With ferrule) N.m 0,75 ... 2,5 mm2 0,75 ... 2,5 mm2 SV 0,75 ... 2,5 mm2 0,75 ... 2,5 mm2 0,8 x 5,5 mm POZIDRIV 2 1,2 Wiring of the power circuit: NUMBER OF WIRES 1 SOLID (No ferrule) SCREWDRIVER TYPE MINIMUM TORQUE 2 (DISTRIBUTION) FINE STRANDED (With ferrule) SOLID (No ferrule) FINE STRANDED (With ferrule) N.m 1,5 ... 10 mm2 1,5 ... 6 mm2 1,5 ... 10 mm2 1,5 ... 6 mm2 0,8 x 5,5 mm POZIDRIV 2 1,8 ® celduc www.celduc.com r e l a i s 5, Rue Ampère BP30004 42290 SORBIERS - FRANCE E-mail : [email protected] Fax +33 (0) 4 77 53 85 51 Service Commercial France Tél. : +33 (0) 4 77 53 90 20 Sales Dept.For Europe Tel. : +33 (0) 4 77 53 90 21 Sales Dept. Asia : Tél. +33 (0) 4 77 53 90 19 S/MOT/SW960330/A/16/03/2000 page 5 / 5 F/GB ® celduc www.celduc.com r e l a i s 5, Rue Ampère BP30004 42290 SORBIERS - FRANCE E-mail : [email protected] Fax +33 (0) 4 77 53 85 51 Service Commercial France Tél. : +33 (0) 4 77 53 90 20 Sales Dept.For Europe Tel. : +33 (0) 4 77 53 90 21 Sales Dept. Asia : Tél. +33 (0) 4 77 53 90 19