Precision Low Ohmic Value Resistor Tin Lead Termination CTLS05/CTLS16/CTLS10/CTLS18/CTLS12/CTLS01 Series Chip Resistor HOW TO ORDER CTLS 10 R015 F J M Packaging M = 7” Reel (10” Reel for 2512) V = 13” Reel TCR (ppm/°°C) R = +15 X = +25 J = +75 K = +100 N = +350 O = +400 Tolerance (%) F = ± 1.0 G = ± 2.0 FEATURES Resistance as low as 0.010 ohm Ultra Precision type with high reliability, stability and quality Y = +50 L = +200 P = +500 Extremely Low TCR, as low as + 75 ppm Wrap Around Terminal for Flow Soldering Anti-Leaching Nickel Barrier Terminations J = ± 5.0 EIA Resistance Code Three significant digits and # of zeros Size 05 = 0402 16 = 0603 10 = 0805 18 = 1206 SCHEMATIC 12 = 2010 01 = 2512 Series Precision Current Sense Resistor Sn/Pb Termination DIMENSIONS (mm) Series CTLS05 CTLS16 CTLS10 CTLS18 CTLS12 CTLS01 Size 0402 0603 0805 1206 2010 2512 L 1.00 + 0.10 1.60 + 0.10 2.00 + 0.20 3.20 + 0.20 5.00 + 0.20 6.40 + 0.20 W 0.50 + 0.10 0.80 + 0.10 1.25 + 0.20 1.60 + 0.15 2.50 + 0.20 3.20 + 0.20 c 0.20 + 0.10 0.20 + 0.10 0.40 + 0.20 0.40 + 0.20 0.60 + 0.30 0.60 + 0.30 t 0.35 + 0.10 0.45 + 0.10 0.50 + 0.10 0.60 + 0.20 0.60 + 0.20 0.60 + 0.20 ELECTRICAL CHARACTERISTICS Size Rated Power 0402 .125W 0603 .125W Max TCR (ppm/°C) Tol .250W ±100ppm ±200ppm 2% 0.100 ~ 4.70 5% 0.100 ~ 4.70 1% 0.100 ~ 0.680 2% 0.100 ~ 0.680 5% 0.100 ~ 0.680 1% 0805 ±75ppm 0.100 ~ 0.500 0.022 ~ 0.080 ±350ppm 0.022 ~ 0.080 0.01 ~ 0.039 5% 0.022 ~ 0.080 0.022 ~ 0.068 0.018 ~ 0.027 0.068 ~ 0.470 0.033 ~ 0.047 1% 0.056 ~ 0.470 0.033 ~ 0.047 0.027 2% 0.056 ~ 0.470 0.033 ~ 0.047 0.018 ~ 0.027 0.056 ~ 0.470 0.001 ~ 0.0649 0.027 0.056 ~ 0.470 0.056 ~ 0.470 0.001 ~ 0.0649 0.001 ~ 0.0649 0.018 ~ 0.027 0.018 ~ 0.027 0.056 ~ 0.470 0.001 ~ 0.0649 0.027 2% 0.056 ~ 0.470 NOTE: The temperature range is -55°C ~ +150°C 0.001 ~ 0.0649 0.018 ~ 0.027 .50W 0.100 ~ 0.500 Max Overload Voltage 25V 50V 50V 100V 150V 300V 200V 400V 200V 400V 200V 400V 0.01 ~ 0.039 2% .5% 1206 ±500ppm Max Working Voltage 0.01 ~ 0.015 .5% 2010 .75W 1% 0.100 ~ 0.500 2% .5% 2512 1.0W 1% American Accurate Components, Inc. 0.100 ~ 0.500 0.01 ~ 0.015 0.01 ~ 0.015 188 Technology Drive, Unit H, Irvine, CA 92618 TEL: 949-453-9888 FAX: 949-453-8889 Email: [email protected] Rated Voltage = √P*R 1 Precision Low Ohmic Value Resistor Tin Lead Termination CTLS05/CTLS16/CTLS10/CTLS18/CTLS12/CTLS01 Series Chip Resistor PERFORMANCE Maximum ∆ Ω Test Item Condition F G, J Short Time Overload ± 0.1% ± 0.5% Load Life ± 0.25% ± 0.5% Moisture Load Life ± 0.25% ± 0.5% Temperature Cycle ± 0.1% ± 0.5% ± 0.1% ± 0.5% The resistor shall withstand dipped into solder for 10±1 sec. At 260±5ºC ± 0.1% ± 0.5% Distance between fulcrums: 90mm; Bending width: 3 mm Resistance to Solder Heat Terminal Strength Insulation Resistance 2.5 times of the rated voltage shall be applied for 5 seconds The resistor shall be subjected to rated voltage for 90 min. followed by a pause of 30 min. at a temperature of 70±3ºC. This constitutes 1 cycle. Cycles shall be repeated for 1000 hours. The resistor subjected to rated voltage for 90 min followed by a pause for 30 min at a temperature of 60±2ºC with relative humidity of 90% to 95%. This constitutes 1 cycles. Cycles shall be repeated for 1000 hours. [-55ºC 30 min → +125ºC 30 min → R.T. 3 min] The resistor shall be subjected to 5 continuous cycles 1000 Meg Ω or over A new uniform coating of solder shall cover minimum of 95% of surface being immersed The resistor shall be dipped into the solder of 215±5ºC for 3±0.5 seconds DC 500V for 1 min. Solderability PACKAGE QUANTITY Package Type M CTL05 10,000 CTL16 5,000 CTL10 5,000 CTL18 5,000 TAPE SCHEMATIC CTL12 5,000 CTL01 5,000 CTL1S 2,000 REEL SCHEMATIC TAPE DIMENSIONS (mm) CTLS05 CTLS16 CTLS10 CTLS18 CTLS12 CTLS01 CTLS1S A 0.65±0.1 1.1±0.2 1.65±0.2 2.0±0.15 2.9±0.1 3.4±0.1 3.4±0.1 B 1.15±0.1 1.9±0.2 2.4±0.2 3.6±0.15 5.3±0.1 6.6±0.1 6.6±0.1 W 8.0±0.2 8.0±0.2 8.0±0.2 8.0±0.2 12.0±0.2 12.0±0.2 12.0±0.2 E 1.75±0.10 1.75±0.1 1.75±0.1 1.75±0.1 1.75±0.1 1.75±0.1 1.75±0.1 F 3.5±0.05 3.5±0.05 3.5±0.05 3.5±0.05 5.5±0.05 5.5±0.05 5.5±0.05 M 180 ± 3.0 H 1.20 C 13.0 ± 0.2 T 0.55±0.1 0.70±0.1 0.85±0.1 0.85±0.1 1.0±0.1 1.0±0.1 1.0±0.1 Tp 0.20±0.05 0.20±0.05 0.20±0.05 0.20±0.05 0.25±0.1 0.25±0.1 0.25±0.1 One side surface of a reel is marked with a label with the following items of information. REEL DIMENSIONS (mm) Reel 7” 10” 13” P1 2.0±0.05 4.0±0.1 4.0±0.1 4.0±0.1 4.0±0.1 4.0±0.1 4.0±0.1 G 9.0 ± 0.3 E 60 ± 1.0 F 11.4 ± 1.0 The content of this specification may change without notification 06/08/2007 1. 2. 3. 4. 5. 6. Chip Resistor Part Number Tolerance Quantity Lot # for production month/year/suffix L* Manufacturer’s name or symbol LABEL DESCRIPTION American Accurate Components, Inc. 188 Technology Drive, Unit H, Irvine, CA 92618 TEL: 949-453-9888 FAX: 949-453-8889 Email: [email protected] 2