Thin Film Precision Chip Resistors Tin Lead Termination HOW TO ORDER CT S 10 - 1003 B X M Packaging M = Std. Reel O = Cutting Tape TCR (PPM/°°C) L = +1 P = +5 M = +2 Q = +10 N = +3 X = +25 Tolerance (%) U=+.01 A=+.05 P=+.02 B=+.10 Y = +50 Z = +100 C=+.25 D=+.50 F=+1 FEATURES High Power Available 0603P 1/8W, 0805P 1/4W, 1206P 1/2W Nichrome Thin Film Resistor Element EIA Resistance Value Standard decade values Size 01=2512 10P=0805P 13=1217 16P=0603P 20=0201 05=0402 11=2020 14=1210 18=1206 10=0805 12=2010 16=0603 18P=1206P Anti-Leaching Nickel Barrier Terminations Very Tight Tolerances, as low as ±0.01% Extremely Low TCR, as low as ±1ppm Special Sizes available 1217, 2020, and 2045 Custom Designs Available. Termination Material S = Tin Lead Series CT = Tin Lead Thin Film Precision Resistors SCHEMATIC DIMENSIONS (mm) Wraparound Termination Top Side Termination, Bottom Isolated – CTG Type Size L W c d t 0201 0.60 + 0.05 0.30 + 0.05 0.13 + 0.05 0.25+0.05 0.25 + 0.05 0402 1.00 + 0.05 0.5+0.1-0.05 0.20 + 0.10 0.25+0.05-0.10 0.35 + 0.05 0603, P 1.60 + 0.10 0.80 + 0.10 0.20 + 0.10 0.30+0.20-0.10 0.50 + 0.10 0805, P 2.00 + 0.15 1.25 + 0.15 0.40 + 0.25 0.30+0.20-0.10 0.50 + 0.15 1206, P 3.20 + 0.15 1.60 + 0.15 0.45 + 0.25 0.40+0.20-0.10 0.60 + 0.15 1210 3.20 + 0.15 2.60 + 0.15 0.50 + 0.30 0.40+0.20-0.10 0.60 + 0.10 1217 3.00 + 0.20 4.20 + 0.20 0.80 + 0.30 0.80 + 0.25 0.9 max 2010 5.00 + 0.15 2.60 + 0.15 0.50 + 0.30 0.40+0.20-0.10 0.70 + 0.10 2020 5.08 + 0.20 5.08 + 0.20 0.80 + 0.30 0.80 + 0.30 0.9 max 2045 5.00 + 0.15 11.5+ 0.30 0.80 + 0.30 0.80 + 0.30 0.9 max 2512 6.30 + 0.15 3.10 + 0.15 0.60 + 0.25 0.50 + 0.25 0.60 + 0.10 CONSTRUCTION FIGURE (Wraparound) CONSTRUCTION MATERIALS Item a b c d & Part Material Resistor Nichrome Thin Film Protective Film Polymide Epoxy Resin Electrode Grounding Layer Nichrome Thin Film Electrode Layer Copper Thin Film Barrier Layer Nickel Plating Solder Layer Solder Plating (Sn) Substrate Alumina Marking Epoxy Resin The resistance value is on the front side The production month is on the backside American Accurate Components, Inc. 188 Technology Drive, Unit H, Irvine, CA 92618 TEL: 949-453-9888 FAX: 949-453-8889 Email: [email protected] 1 Thin Film Precision Chip Resistors Tin Lead Termination ELECTRICAL CHARACTERISTICS Size Power Rating at 70°° (W) 0201 0.031 0402 0603 0603P 0805 0805P 0.031 0.063 0.063 0.100 0.125 0.100 0.250 1206 0.125 1206P 0.500 1210 1217 2010 0.250 0.250 0.250 Resistance Range ±% Tolerance TCR (10-6/°°C) 10.0 ~ 30.0 1 ±100 33.0 ~ 22.0K 0.5 ±25 10.0 ~ 46.4 0.1, 0.5, 1 ±10, ±25, ±50 47.0 ~ 97.6 0.05, 0.1, 0.25, 0.5, 1 ±10, ±25, ±50 100 ~ 2.94K 0.02, 0.05, 0.1, 0.25, 0.5, 1 ±5, ±10, ±25, ±50 3.00K ~ 100K 0.05, 0.1, 0.25, 0.5, 1 ±10, ±25, ±50 10.0 ~ 100K 0.01, 0.02, 0.05, 0.1, 0.25, 0.5, 1 1,2,3,5,10,25,50 102K ~ 270K 0.05, 0.1, 0.25, 0.5, 1 10, 25, 50 274K ~ 360K 0.1, 0.25, 0.5, 1 10, 25, 50 1.0 - 9.1 0.5, 1 ±50, ±100 10 - 390K 0.1, 1.0 ±10, ±25, ±50, ±100 10.0 ~ 200K 0.01, 0.02, 0.05, 0.1, 0.25, 0.5, 1 1, 2, 3, 5, 10, 25, 50 205K ~ 360K 0.05, 0.1, 0.25, 0.5 10, 25, 50 365K ~ 487K 0.05, 0.1, 0.25, 0.5 10, 25 499K ~ 1.00M 0.1, 0.5 25 1.0 - 9.1 0.5, 1 ±50, ±100 10 - 800K 0.1, 1.0 ±10, ±25, ±50, ±100 5.01 ~ 560K 0.01, 0.02, 0.05, 0.1, 0.25, 0.5, 1 1, 2, 3, 5, 10, 25, 50 562K ~ 1.00M 0.05, 0.1, 0.25, 0.5 10, 25 1.0 - 9.1 0.5, 1 ±50, ±100 10 ~ 1.00M 0.1, 1.0 ±10, ±25, ±50, ±100 100 ~ 330K 0.1 ±5, ±10 51.0 ~ 2.00M 0.1, 0.5 ±25 10.0 ~ 49.9 0.5 ±50 5.10 ~ 1.00M 0.01, 0.02, 0.05, 0.1, 0.25, 0.5, 1 ±1, 2, 3, 5, 10, 25 100 ~ 20.0K 0.01, 0.05, 0.1, 0.25, 0.5 ±5 50.0 ~ 40.0K 0.01, 0.05, 0.1, 0.25, 0.5 ±10 10.0 ~500K 0.01, 0.05 4.70 -1.00M 0.1, 0.25, 0.5, 1 10.0 ~500K 0.01, 0.05 1.00 ~ 1.00M 0.1, 0.25, 0.5, 1 ±25 Working Voltage Overload Voltage Operating Temp Range 15V 30V -55°C ~ +125°C 50V 100V -55°C ~ +125°C -55°C ~ +125°C 75V 150V -55°C ~ +125°C 75V 150V -55°C ~ +125°C 100V 200V -55°C ~ +125°C 150V 300V -55°C ~ +125°C 150V 300V -55°C ~ +125°C 150V 300V -55°C ~ +125°C 200V 400V -55°C ~ +125°C 200V 400V -55°C ~ +155°C 150V 300V -55°C ~ +125°C ±50 2020 0.500 5.10 ~ 2.00M 0.01, 0.02, 0.05, 0.1, 0.25, 0.5, 1 ±1, 2, 3, 5, 10, 25 350V 700V -55°C ~ +155°C 2045 1.000 20.0 ~ 4.99M 0.01, 0.02, 0.05, 0.1, 0.25, 0.5, 1 ±1, 2, 3, 5, 10, 25 500V 1000V -55°C ~ +155°C 100 ~ 20.0K 0.01, 0.05, 0.1, 0.25, 0.5 ±5 50.0 ~ 40.0K 0.01, 0.05, 0.1, 0.25, 0.5 ±10 150V 300V -55°C ~ +125°C 2512 0.500 10.0R ~ 500K 0.01, 0.05 4.70 -1.00M 0.1, 0.25, 0.5, 1 10.0R ~ 500K 0.01, 0.05 1.00 1.00M 0.1, 0.25, 0.5, 1 ±25 ±50 * Rated Voltage: √PxR American Accurate Components, Inc. 188 Technology Drive, Unit H, Irvine, CA 92618 TEL: 949-453-9888 FAX: 949-453-8889 Email: [email protected] 2 Thin Film Precision Chip Resistors Tin Lead Termination PERFORMANCE & ENVIRONMENTAL SPECIFICATIONS Maximum ∆ Ω +0.05Ω (Tolerance) A B, C D, F ± 0.1% ± 0.1% ± 0.5% Test Item Short Time Overload Load Life ± 0.1% ± 0.25% ± 0.5% Moisture Load Life ± 0.1% ± 0.25% ± 0.5% Temperature Cycle ± 0.1% ± 0.1% ± 0.5% Resistance to Solder Heat ± 0.05% ± 0.1% ± 0.5% Terminal Strength ± 0.1% ± 0.1% ± 0.5% A new uniform coating of solder shall cover minimum of 95% of surface being immersed DC 500V for 1 minute Solderability Insulation Resistance Condition 2.5 times of the rated voltage shall be applied for 5 seconds The resistor shall be subjected to rated voltage for 90 min. followed by a pause of 30 min. at a temperature of 70±3ºC. This constitutes 1 cycle. Cycles shall be repeated for 1000 hours. The resistor subjected to rated voltage for 90 min followed by a pause for 30 min at a temperature of 60±2ºC with relative humidity of 90% to 95%. This constitutes 1 cycle. Cycles shall be repeated for 1000 hours. [-55ºC 30 min → +125ºC 30 min → R.T. 3 min] The resistor shall be subjected to 5 continuous cycles The resistor shall withstand dipped into solder for 10±1 sec. At 260±5ºC Distance between fulcrums: 90mm; Bending width: 3 mm The resistor shall be dipped into the solder of 235±5ºC for 3±0.5 seconds 1000 Meg Ω or over VALUE MARKING For those parts ordered with an E-24 value, the product will be marked with a 3 digit code. For those products ordered with an E-96 value, the product will be marked with a 4 digit code. For those parts which fall under E-96 and E-24 values (e.g. 1K ohm is both an E-96 and E-24 value), the part will be marked with a 3 digit code; 4 digit markings for this type is available upon special request. 0201, and 0402 Size No marking E-24 & E-96 Values Custom Value Any Size 103 1213 C E F G H M O & M Type 7” Reel ∅13± 0.2 60±0.5 11.4±1.0 9.0±0.3 1.5±0.3 ∅180±2.0 M Type 13” Reel ∅13±0.2 100±0.2 13.5±1.0 9.5±0.5 2.0±0.5 ∅330±2.0 Reel size is dependent upon the package quantity& resistor size. Call for more info. 0603 Size EIA 96 Digit Code of 3.32K ohm E-96 Values 51B REEL SCHEMATIC & DIMENSIONS (mm) TAPE SCHEMATIC 0603 ~ 2512 Sizes EIA 3 Digit Code of 10K ohm resistor E-24 Values, E-96 Values 0805 ~ 2512 Sizes EIA 4 Digit Code of 121K ohm resistor E-96 Values LABEL DESCRIPTION One side surface of a reel is marked with a label with the following items of information. 1. Chip Resistor 2. Part Number 3. Tolerance 4. Quantity 5. Lot number for production month/year* 6. Manufacturer’s name or symbol TAPE DIMENSIONS (mm) PACKAGE QUANTITY Type M O Type B O 0201 5,000 1,000 1210 5,000 1,000 0402 10,000 1,000 1217 2,000 1,000 0603 5,000 1,000 2010 4,000 1,000 2020 2,000 1,000 0805 5,000 1,000 2045 3,000 1,000 1206 5,000 1,000 2512 4,000 1,000 The content of this specification may change without notification 05/15/2015 American Accurate Components, Inc. A B W E F P1 T Tp 0201 0.41±0.1 0.71±0.1 8.0±0.2 1.75±0.10 3.5±0.05 2.0±0.05 0.5max 0.4+0.05 A B W E F P1 T Tp 1210 2.9±0.1 3.5±0.1 8.0±0.2 1.75±0.1 3.5±0.05 4.0±0.1 0.90±0.1 0.75±0.1 0402 0.65±0.1 1.15±0.1 8.0±0.2 1.75±0.10 3.5±0.05 2.0±0.05 0.55±0.1 0.40±0.05 1217 3.5±0.1 4.9±0.1 12.0±0.2 1.75±0.1 5.5±0.1 8.0±0.1 0.90±0.1 0603 1.1±0.1 1.9±0.1 8.0±0.2 1.75±0.1 3.5±0.05 4.0±0.1 0.64±0.1 2010 2.9±0.1 5.3±0.1 12.0±0.2 1.75±0.1 5.5±0.1 4.0±0.1 1.0±0.1 0.25±0.1 188 Technology Drive, Unit H, Irvine, CA 92618 TEL: 949-453-9888 FAX: 949-453-8889 Email: [email protected] 2020 5.5±0.1 5.5±0.1 12.0±0.2 1.75±0.1 5.5±0.1 8.0±0.1 1.0±0.1 0805 1.6±0.15 2.4±0.2 8.0±0.2 1.75±0.1 3.5±0.05 4.0±0.1 0.84±0.1 2045 5.4±0.1 11.9±0.1 24.0±0.2 1.75±0.1 11.5±0.1 8.0±0.1 1.0±0.1 1206 2.0±0.15 3.6±0.2 8.0±0.2 1.75±0.1 3.5±0.05 4.0±0.1 0.84±0.1 2512 2.9±0.1 5.3±0.1 12.0±0.2 1.75±0.1 5.5±0.05 4.0±0.1 1.0±0.1 0.25±0.1 3