MNA02 Ceramic capacitors (1005 (0402) ×2 size, chip capacitor networks) MNA02 zFeatures Two multi-layer ceramic capacitors are integrated on a single chip providing reduced cost and mounting space. zQuick Reference The design and specifications are subject to change without prior notice. Please check the most recent technical specifications prior to placing orders or using the product. For more detail information regarding packaging style code, please check product designation. zHigh dielectric constant Part No. Size code MNA02 1005x2 (0402x2) Temperature characteristics code CN Operating temp. range (°C) Rated voltage (V) Capacitance(pF) Capacitance tolerance Thickness (mm) −25 to +85 6.3 1,000,000 M(±20%) 0.8+0.05 −0.10 ±15% (X5R) zExternal dimensions (Unit : mm) 0.2±0.1 1.00±0.15 1.37±0.15 0.8+0.05 -0.10 0.36±0.1 C1 C2 0.64±0.1 C1 =C 2 zProduct designation Packaging specifications Code Product thickness K 0.8mm Paper tape(width 8 mm, pitch 4 mm) Reel φ180mm(7in.) Basic ordering unit(pcs.) 4,000 Reel(φ180mm) : compatible with EIAJ ET-7200A Packaging style Part No. M N A Rated voltage Code Voltage 8 6.3V 0 2 8 C N Temperature characteristic code :Refer to quick reference table. 1 0 5 M K Nominal capacitance 3-digit designation according to IEC Capacitance tolerance tolerance Code M ±20% 1/6 MNA02 Ceramic capacitors zPerformance and test method No. Items Test Method (As per JIS C 5101-1, JIS C 5101-10) Performance 1 Appearance and dimensions No marked defects shall be allowed As per 4.4 of JIS C 5101-1. As per 4.5 of JIS C 5101-10 for appearance. Dimensions shall be as specified the Using a Magnifier. clause 4. 2 Withstanding voltage No dielectrical breakdown or other damage shall be allowed. As per 4.6 of JIS C 5101-1. As per 4.6.4 of JIS C 5101-10 Voltage shall be applied as per Table1. Table 1 Characteristic Voltage CN 250% Rated voltage Voltage shall be applied for 1 to 5s with 50mA charging and discharging current. 3 Insulation resistance Not less than 100MΩ µF As per 4.5 of JIS C 5101-1. As per 4.6.3 of JIS C 5101-10 Measurements shall be made after 60+/−5s period of the rated voltage applied. 4 Capacitance within +/−20% As per 4.7 of JIS C 5101-1. As per 4.6.1 of JIS C 5101-10 Measurements shall be made under the conditions specified in Table 2. Table 2 Characteristic CN 5 Dielectric loss tangent 6 Temperature characteristic tan δ < − 10.0% 7 Solderability Voltage 1+/−0.1kHz 1+/−0.1Vrms. As per 4.8 of JIS C 5101-1. As per 4.6.2 of JIS C 5101-10 Measurements shall be made under the conditions specified in Table 2. Applied Capacitance Temperature voltage range 0Vdc Within +/−15% −55°C~ +85°C 0Vdc Within +/−10% −25°C~ +85°C Within +0/−30% −25°C~ +85°C 3.15 Vdc Frequency More than 3/4 of each end termination shall be covered with new solder. As per 4.24 of JIS C 5101-1. As per 4.7 of JIS C 5101-10 If required, measurements shall be made at a given temperature. Measurements shall be made under the conditions specified in Table 2. Table 2 Characteristic CN Frequency Voltage 1+/−0.1kHz 1+/−0.1Vrms. As per 4.15.2 of JIS C 5101-1. As per 4.11 of JIS C 5101-10 The solder specified in JIS Z 3282 H63A shall be used. And the flux containing 25% rosin and ethanol solution shall be used. The specimens shall be immersed into the solder at 235+/−5°C for 2+/−0.5s So that both end terminations are completely under solder. 2/6 MNA02 Ceramic capacitors No. 8 Items Performance Resistance Appearance Without mechanical damage. to soldering heat Change Within +/−7.5% rate from initial value Dielectric loss tangent Within specified initial value. Insulation resistance Within specified initial value. Withstanding No defects shall be allowed. voltage Test Method (As per JIS C 5101-1, JIS C 5101-10) As per 4.14 of JIS C 5101-1. As per 4.10 of JIS C 5101-10 The solder specified in JIS Z 3282. H63A shall be used. The specimens shall be immersed into the solder at 260+/−5°C for 5+/−0.5s so that both end terminations are completely under the solder. Pre-heating at 150+/−10°C for 1 to 2min Initial measurements prior to test shall be performed after the thermal Pre-conditioning specified in Remarks (1). Final measurements shall be made after the specimens have been left at room temperature as per Table3. Table 3 Characteristic Time CN 9 End termination adherence Without peeling or sign of peeling shall be allowed on the end terminations. 48+/−4 h As per 4.13 of JIS C 5101-1. As per 4.8 ofJIS C 5101-10 A 2N weight for 10+/−1s shall be applied to the soldered specimens as shown by the arrow mark in the below sketch. Applied pressure Capacitor Substrate 10 Bending strength Appearance Without mechanical damage. As per 4.35 of JIS C 5101-1. As per 4.9 of JIS C 5101-10 Glass epoxy board with soldered specimens shall be bent till 1mm by 1.0mm/s. 11 Vibration Appearance Without mechanical damage. As per 4.17 of JIS C 5101-1. The specimens shall be soldered on the specified test jig. Initial measurements shall be made after the thermal pre-conditioning specified in Remarks(1). Final measurements shall be made after the specimens have been left at room temperature as per Table3. [Condition] Directions : 2h each X, Y and Z directions Total : 6h Frequency range : 10 to 55 to 10Hz(1min) Applitude : 1.5mm (shall not exceed acceleration196m/s2) Change rate from initial value Within +/−7.5% Dielectric loss tangent Within specified initial value. Table 3 Characteristic CN Time 48+/−4 h 3/6 MNA02 Ceramic capacitors No. 12 Items Performance Temperature Appearance Without mechanical damage. cycling Change Within +/−15.0% rate from initial value Dielectric loss tangent Within specified initial value. Insulation resistance Within specified initial value. Test Method (As per JIS C 5101-1, JIS C 5101-10) As per 4.16 of JIS C 5101-1 As per 4.12 of JIS C 5101-10 The specimens shall be soldered on the test jig shown in Remarks. Temperature cycle : 100cycles Initial measurements prior to test shall be performed after the thermal per-conditioning specified in Remarks (1). Final measurements shall be made after the specimens have been left at room temperature as per Table3. Test condition Withstanding No defects shall be allowed. voltage Step Temp. (°C) Time (min) 1 Min operating temp. 2 Room temp. 30+/−3 < −3 3 Max operating temp. 4 Room temp. Table 3 Characteristic CN 13 Humidity (Steady) Appearance Without mechanical damage. Change rate from initial value Within +/−25% Dielectric tangent Less than 200% of initial spec. Insulation resistance Not less than 10MΩ. Humidity life test Appearance Without mechanical damage. Change rate from initial value Within +/−25.0% Dielectric loss tangent Less than 200% of initial spec. Insulation resistance Not less than 5MΩ. Time 48+/−4 h As per 4.22 of JIS C 5101-1 As per JIS C 5101-10 Test temperature : 60+/−2°C Relative humidity : 90 to 95% Test time : 500 +24/−0 h Initial measurements prior to test shall be made after the voltage pre-conditioning specified in Remarks (2). Final measurements have been left at room temperature as per Table3. Table 3 Characteristic Time CN 14 30+/−3 < −3 48+/−4 h As per 4.22 of JIS C 5101-1 As per 4.14 of JIS C 5101-10 Test temperature : 60+/−2°C Relative humidity : 90 to 95% Voltage : Rated voltage Test time : 500 +24/−0 h Initial measurements prior to test shall be made after the voltage pre-conditioning specified in Remarks (2). Final measurements shall be made after the specimens have been left at room temperature as per Table3. Table 3 Characteristic Time CN 48+/−4 h 4/6 MNA02 Ceramic capacitors No. 15 Items Heat life test Performance Appearance Without mechanical damage. Change rate from initial value Within +/−25.0% Dielectric loss tangent Less than 200% of initial spec. Insulation resistance Not less than 10MΩ. Test Method (As per JIS C 5101-1, JIS C 5101-10) As per 4.23 of JIS C 5101-1. As per 4.15 of JIS C 5101-10 Test Voltage temperature Test time (h) Rated voltage 1000 +48/−0 85°C Initial measurements prior to test shall be made after the voltage pre-conditioning specified in Remarks (2). Final measurements shall be made after the specimens have been left at room temperature Table 3 Characteristic CN Time 48+/−4 h [Remarks] Pre-conditioning If specified in test method of as per 3(Performance and test method), capacitors of CNcharacteristics shall be pre-conditionded as follows. (1) Thermal pre-conditioning Prior to initial measurements, specimens shall be conditioned at a temperature of 150 0/−10°C for a period of 1hr., and shall be allowed to stabilize at room temperature for 48+/−4h (2) Voltage pre-conditioning Prior to initial measurements, voltage specified as a test condition shall be applied to specimens for a period of 1hr., and the specimens shall be allowed to stabilize at room temperature for 48+/−4h <Test jig> Soldering Glass epoxy substrate 5/6 MNA02 Ceramic capacitors zPackaging specifications Taping dimensions Reel dimensions t φJ E D G φ13.0 + − 0.2 F t1 H K, L Pulling direction Symbol Dimensions C D G F H J t t1 3.5 0.95 1.05 8.00 1.75 4.0 2.0 4.0 φ1.5 +/ −0.20 +/ −0.05 +/ −0.10 +/ −0.10 +/ −0.05 +/ −0.10 +0.1/ −0 +/ −0.05 MAX. Symbol A Style MNA02 E +1.0 9.0 −0 Pulling direction +0 φ180 −1.5 C B φ60.0+1.0 −0 A Label pasting B As per EIAJ ET−7200A (Unit : mm) 1.30+/−0.051.70+/−0.05 (Unit : mm) 30 20 30 0 −10 −20 −30 Dissipation factor (%) Capacitance change (%) zElectrical characteristics curves 15 10 5 −80 −40 0 40 80 120 Fig.1 Temperature (°C) 6/6 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1