G THIS DRAWING, THE STRUCTURAL DESIGN DISCLOSED THEREIN AND THE TECHNICAL DATA AND ENGINEERING SERVICE REPRESENTED THEREBY ARE THE EXCLUSIVE PROPERTY OF HUCK INTERNATIONAL, INC. Alcoa Fastening Systems BLIND RIVET CURRENT DESIGN ACTIVITY CAGE CODE 0HDW7 AFS TUCSON OPERATIONS 3724 EAST COLUMBIA STREET TUCSON, ARIZONA 85714 PHONE (520) 519-7400 FAX (520) 519-7454 G ENGINEERING STANDARD F C L 25 MAX LOCK COLLAR 10 GRIP COUNTERBORE OF SLEEVE SHANK OPTIONAL R.020 MAX DRIVE WASHER SPINDLE SLEEVE A 1 MANUFACTURER'S IDENTIFICATION 4 B LOCK COLLAR MAY BE IN THIS AREA "O" FOR OVERSIZE 8 2 INSTALLED FASTENER PART NUMBER SLEEVE CODE BLANK - FOR 5056 CODE C - FOR A-286 CODE M - FOR MONEL TABLE I DIA. 1/64 Ø A SIZE OVER +.003 SIZE -.001 NOM. 3 ØB GRIP NUMBER ( HEAD MARKING ARRANGEMENT OPTIONAL ) C G SHEAR TENSILE HOLE 6 6 +.010 MIN. LIMITS ALUM. MONEL A-286 ALUM. MONEL -.000 CRES & A-286 5 CRES OSMLSP-( )04 04 .140 .140 .250±.012 .054 .788 560 1090 1235 325 675 OSMLSP-( )05 05 .173 .173 .312±.016 .067 .788 855 1665 1880 490 1050 OSMLSP-( )06 06 .201 .201 .375±.019 .080 .788 1165 2395 2530 715 1500 OSMLSP-( )08 08 .266 .266 .500±.025 .107 1.000 2015 4250 4495 1200 2600 .146 .143 .180 .176 .209 .205 .275 .271 NOTES: 1. .001 SHANK DIAMETER INCREASE PERMISSIBLE WITHIN .100 FROM BASE OF HEAD. 2. MARKING OF ALUMINUM RIVETS MAY BE ON SPINDLE AT MANUFACTURER'S OPTION. 3. "A" DIAMETER MAY BE .001 LARGER THAN SHOWN FOR CADMIUM PLATED OR ALUMINUM COATED SLEEVES. 4. "A" DIAMETER MAY BE .001 SMALLER BEYOND MINIMUM GRIP LENGTH. 5. ADJUST AS REQUIRED, WITHIN THESE LIMITS, TO SUIT MATERIAL AND APPLICATION. 6. MINIMUM ULTIMATE SHEAR AND TENSILE STRENGTHS, IN POUNDS, OF INSTALLED BLIND RIVET. G ISSUED REVISED PAGE PER DCN 10241, ADD TABLE LABELS, CHANGE FORMAT TO MATCH 9 CURRENT STANDARDS, UPDATE SPECIFICATIONS AND TABLE I I 6/29/1977 UNIMATIC ® BLIND RIVET, GENERAL PURPOSE, PROTRUDING HEAD, BULBED, MECHANICALLY-LOCK-SPINDLE, 1/64 OVERSIZE, 11/21/2011 5056 ALUMINUM, MONEL & A-286 CRES RIVET SLEEVES 1 OF 3 DIMENSIONS IN INCHES PROCUREMENT SPEC NAS1919 DRAWN BY SIGNER J. SCHLOBOHM INITIALS CHECKED BY D. PARSONS OSMLSP-( ) BLR123 G THIS DRAWING, THE STRUCTURAL DESIGN DISCLOSED THEREIN AND THE TECHNICAL DATA AND ENGINEERING SERVICE REPRESENTED THEREBY ARE THE EXCLUSIVE PROPERTY OF HUCK INTERNATIONAL, INC. Alcoa Fastening Systems BLIND RIVET CURRENT DESIGN ACTIVITY CAGE CODE 0HDW7 AFS TUCSON OPERATIONS 3724 EAST COLUMBIA STREET TUCSON, ARIZONA 85714 PHONE (520) 519-7400 FAX (520) 519-7454 ENGINEERING STANDARD 7. GRIP SYMBOL FOR -00 SHALL BE GREEK LETTER THETA "Θ". 8. BLIND SIDE HEAD MAY BE INSTALLED ON 5° MAXIMUM SLOPE. 9. THE RIVETS COVERED IN THIS STANDARD ARE INTENDED FOR USE AS A REPAIR/REPLACEMENT FOR NAS1919 OR FOR NEW DESIGN APPLICATIONS. 10. OPTIONAL DRIVE WASHER FACILITATES INSTALLATION WITH BLUNT NOSE TOOL. DRIVE WASHER NOT PART OF INSTALLED FASTENER. NOTE: 1. THIS RIVET IS INTENDED FOR GENERAL PURPOSE USE IN BOTH THICK SHEET STACKUP AND IN THIN SHEET APPLICATIONS. . 2. RIVETS FOR SINGLE ACTION (NON-SHIFTING) TOOLING SHALL BE IDENTIFIED WITH A DEPRESSED "S" ON SPINDLE HEAD OR COLORED YELLOW ON SPINDLE (LOCATION OPTIONAL). TABLE I I GRIP DASH NO. 7 01 02 03 04 05 06 07 08 09 10 11 12 13 14 OSMLSP-( )04 (.125 DIA. NOM) GRIP RANGE MIN. MAX. .025 .063 .126 .188 .251 .313 .062 .125 .187 .250 .312 .375 L F MAX MAX .198 .260 .323 .385 .448 .510 .338 .443 .568 .693 .818 .943 OSMLSP-( )05 (.156 DIA. NOM) GRIP RANGE MIN. MAX. .031 .063 .126 .188 .251 .313 .376 .438 .501 .563 .062 .125 .187 .250 .312 .375 .437 .500 .562 .625 L MAX F MAX .227 .273 .336 .398 .461 .523 .586 .648 .711 .773 .378 .478 .602 .727 .852 .977 1.102 1.227 1.352 1.477 OSMLSP-( )06 (.190 DIA. NOM) GRIP RANGE MIN. MAX. .037 .063 .126 .188 .251 .313 .376 .438 .501 .563 .626 .688 .062 .125 .187 .250 .312 .375 .437 .500 .562 .625 .687 .750 L MAX F MAX .251 .287 .350 .412 .475 .537 .600 .662 .725 .787 .850 .912 .431 .526 .651 .776 .901 1.026 1.151 1.276 1.401 1.526 1.651 1.776 OSMLSP-( )08 (.250 DIA. NOM) GRIP RANGE MIN. MAX. .063 .126 .188 .251 .313 .376 .438 .501 .563 .626 .688 .751 .813 .125 .187 .250 .312 .375 .437 .500 .562 .625 .687 .750 .812 .875 L MAX F MAX .335 .397 .460 .522 .585 .647 .710 .772 .835 .897 .960 1.022 1.085 .606 .731 .856 .981 1.106 1.231 1.356 1.481 1.606 1.731 1.856 1.981 2.106 EXAMPLES OF PART NUMBERS: OSMLSP-EU05-04 - A-286 CRES RIVET, .173 DIAMETER, GRIP RANGE .188 TO .250, PASSIVATE FINISH. OSMLSP-EU05-04C - A-286 CRES RIVET, .173 DIAMETER, GRIP RANGE .188 TO .250, CADMIUM PLATED SLEEVE. OSMLSP-M05-04 - MONEL RIVET, .173 DIAMETER, GRIP RANGE .188 TO .250, UNPLATED SLEEVE. OSMLSP-M05-04C - MONEL RIVET, .173 DIAMETER, GRIP RANGE .188 TO .250, CADMIUM PLATED SLEEVE. OSMLSP-M05-04A - MONEL RIVET, .173 DIAMETER, GRIP RANGE .188 TO .250, ALUMINUM COATED SLEEVE. OSMLSP-M05-04P - MONEL RIVET, .173 DIAMETER, GRIP RANGE .188 TO .250, LUBRICATED AS REQUIRED. OSMLSP-M05-04EL - MONEL RIVET, .173 DIAMETER, GRIP RANGE .188 TO .250, DICHRONITE DL-5 DRY FILM LUBRICANT (PIN ONLY). OSMLSP-B05-04 - 5056 ALUMINUM RIVET, .173 DIAMETER, GRIP RANGE .188 TO .250 OSMLSP-B05-04EL - 5056 ALUMINUM RIVET, .173 DIAMETER, GRIP RANGE .188 TO .250, DICHRONITE DL-5 DRY FILMLUBRICANT (PIN ONLY). OSMLSP-B05-04U - 5056 ALUMINUM RIVET, .173 DIAMETER, GRIP RANGE .188 TO .250, OPTIONAL DRIVE WASHER DIMENSIONS IN INCHES G ISSUED PER DCN 10241, ADD TABLE LABELS, CHANGE FORMAT TO MATCH CURRENT STANDARDS, UPDATE SPECIFICATIONS AND TABLE I I 6/29/1977 REVISED 11/21/2011 2 OF 3 PAGE 9 PROCUREMENT SPEC NAS1919 UNIMATIC ® BLIND RIVET, GENERAL PURPOSE, PROTRUDING HEAD, BULBED, MECHANICALLY-LOCK-SPINDLE, 1/64 OVERSIZE, 5056 ALUMINUM, MONEL & A-286 CRES RIVET SLEEVES DRAWN BY SIGNER J. SCHLOBOHM INITIALS CHECKED BY D. PARSONS OSMLSP-( ) BLR123 CURRENT DESIGN ACTIVITY CAGE CODE 0HDW7 AFS TUCSON OPERATIONS 3724 EAST COLUMBIA STREET TUCSON, ARIZONA 85714 PHONE (520) 519-7400 FAX (520) 519-7454 G THIS DRAWING, THE STRUCTURAL DESIGN DISCLOSED THEREIN AND THE TECHNICAL DATA AND ENGINEERING SERVICE REPRESENTED THEREBY ARE THE EXCLUSIVE PROPERTY OF HUCK INTERNATIONAL, INC. Alcoa Fastening Systems BLIND RIVET ENGINEERING STANDARD TABLE I I I RIVET COMPONENTS COMPOSITION B COMPOSITION EU COMPOSITION M SLEEVE 5056 ALUMINUM PER QQ-A-430 A-286 CRES PER CHEMICAL RQMT OF AMS5737 MONEL PER QQ-N-281 SPINDLE 2024 ALUMINUM PER QQ-A-430 A-286 CRES PER CHEMICAL RQMT OF AMS5737 A-286 CRES PER CHEMICAL RQMT OF AMS5737 5056 ALUMINUM PER QQ-A-430 A-286 CRES PER CHEMICAL RQMT OF AMS5737 OR 316 CRES (UNS S31600) PER CHEMICAL RQMT OF AMS5690 A-286 CRES PER CHEMICAL RQMT OF AMS5737, MONEL PER QQ-N-281, OR 316 CRES (UNS S31600) PER CHEMICAL RQMT OF AMS5690 COMPONENTS LOCK RING FINISHES SLEEVE NONE OR AVAILABLE WITH SPECIAL COATINGS. SEE CODES BELOW PASSIVATE PER AMS2700, AND AMS-QQ-P-35, OR CADMIUM PLATE PER AMS-QQ-P-416, TYPE I I, CLASS 3 OR ALUMINUM COAT PER NAS4006 NONE, OR CADMIUM PLATE PER AMS-QQ-P-416, TYPE I I, CLASS 3 OR ALUMINUM COAT PER NAS4006 SPINDLE CHEMICALLY SURFACE TREAT PER MIL-DTL-5541, CL 1A PASSIVATE PER AMS2700 AND AMS-QQ-P-35 PASSIVATE PER AMS2700 AND AMS-QQ-P-35 LOCK RING NONE OR CHEMICALLY SURFACE TREAT PER MIL-DTL-5541, CL 1A PASSIVATE PER AMS2700 AND AMS-QQ-P-35 PASSIVATE PER AMS2700 AND AMS-QQ-P-35, FOR A-286 & 316 CRES ONLY FIRST SERIES OF TWO DIGIT NUMBERS FOLLOWING MATERIAL DESIGNATOR IS DIAMETER IN .0312 INCREMENTS. SECOND SERIES OF TWO DIGIT NUMBERS FOLLOWING MATERIAL DESIGNATOR IS MAXIMUM GRIP IN .0625 INCREMENTS. ADD "A" AFTER SECOND SERIES OF TWO DIGIT NUMBERS FOR ALUMINUM COATING PER NAS 4006. ADD "B" AFTER BASIC NUMBER FOR COMPOSITION B ALUMINUM RIVET. ADD "EU" AFTER BASIC NUMBER FOR COMPOSITION EU A-286 CRES RIVET. ADD "M" AFTER BASIC NUMBER FOR COMPOSITION M MONEL RIVET. ADD "P" AFTER SECOND SERIES OF TWO DIGIT NUMBERS FOR DRY FILM LUBRICATION OR NONE AS REQUIRED TO DESIGNATE RIVET MAY BE SLOSH CLEANED WITH A-A-59281 CLEANER BEFORE INSTALLATION. ADD "C" AFTER SECOND SERIES OF TWO DIGIT NUMBERS FOR CADMIUM PLATED RIVET SLEEVE. ADD "EL" AFTER SECOND SERIES OF TWO DIGIT NUMBERS FOR DICHRONITE DL-5 DRY FILM LUBRICANT (PIN ONLY). ADD "FC" AFTER SECOND SERIES OF TWO DIGIT NUMBERS OF COMPOSITION B RIVETS FOR CHEMICAL FILM PER MIL-DTL-5541, CL 1A. ADD "U" AFTER SECOND SERIES OF TWO DIGIT NUMBERS FOR DRIVE WASHER FOR BLUNT NOSED TOOL INSTALLATION. DIMENSIONS IN INCHES DCN 10241, ADD TABLE LABELS, CHANGE FORMAT TO MATCH G PER 9 CURRENT STANDARDS, UPDATE SPECIFICATIONS AND TABLE I I ISSUED 6/29/1977 UNIMATIC ® BLIND RIVET, GENERAL PURPOSE, PROTRUDING HEAD, BULBED, MECHANICALLY-LOCK-SPINDLE, 1/64 OVERSIZE, REVISED 11/21/2011 5056 ALUMINUM, MONEL & A-286 CRES RIVET SLEEVES PAGE 3 OF 3 PROCUREMENT SPEC NAS1919 DRAWN BY J. SCHLOBOHM SIGNER INITIALS CHECKED BY D. PARSONS OSMLSP-( ) BLR123