THIS DRAWING, THE STRUCTURAL DESIGN DISCLOSED THEREIN AND THE TECHNICAL DATA AND ENGINEERING SERVICE REPRESENTED THEREBY ARE THE EXCLUSIVE PROPERTY OF HUCK INTERNATIONAL, INC. H Unimatic ® CURRENT DESIGN ACTIVITY CAGE CODE 0HDW7 AFSR TUCSON OPERATIONS 3724 EAST COLUMBIA STREET TUCSON, ARIZONA 85714 PHONE (520) 519-7400 FAX (520) 519-7454 Alcoa Fastening Systems & Rings ADVANCED BLIND BOLT ENGINEERING STANDARD C M K N L H B 9 5 SLEEVE G D PIN 130°±1° J A GRIP R RAD 4 S 3 8 E .005 CROWN HEIGHT A' W 6 INSTALLED FASTENER PART NUMBER O/S ( Ø A ) DIA. HEAD THEO. INTER. HEAD ID WITHOUT DRIVE WASHER TABLE I Ø A' MIN B C HEAD MIN. HEIGHT MAX ØD E ØG H ØJ K SLEEVE MAX GAGE GAGE ±.005 ±.030 ±.001 ±.0001 HEIGHT N R (S) Ø W SINGLE TENSILE SPINDLE HOLE ±.060 RAD. DESIGN MIN. SHEAR RET. LIMITS MAX. REF +.003 1 -.000 1 2 OUAB130-EU05-( ) 05 .332 .296 .036 .844 .179 OUAB130-EU06-( ) 06 .386 .347 .040 .875 .214 OUAB130-EU08-( ) 08 .507 .463 .054 1.000 .275 .0188 .0148 .0192 .335 .3271 .0152 .0237 .385 .4319 .0197 .315 .2831 .375 7 .800 .140 .025 .247 .242 1980 1050 525 .180 .830 .160 .025 .307 .289 2925 1500 750 .215 .975 .190 .030 .376 .371 5000 2600 1300 .276 1. MINIMUM ULTIMATE SINGLE SHEAR AND TENSILE STRENGTHS IN POUNDS OF INSTALLED FASTENER. 2. APPLIES TO GRIPS 05-04 MAX, 06-05 MAX, 08-06 MAX AND UP. IN SHORTER GRIPS, A TRUE COMPOSITE SHEAR TEST CANNOT BE OBTAINED. 3. TRIM FLASH NOT TO EXCEED .005 MAXIMUM LENGTH ABOVE HEAD OF PIN. 4. SOLID OR SPLIT LOCK COLLAR - MANUFACTURER'S OPTION. SPLIT NOT TO EXCEED .020 WIDTH. 5. KNURLED TO FACILITATE FASTENER ASSEMBLY. NOT PART OF THE INSTALLED FASTENER. 6. BLIND SIDE HEAD MAY BE INSTALLED ON 7 MAXIMUM SLOPE. 7. IDENTIFICATION: HUCK SYMBOL, "O", "C" (MATERIAL) AND GRIP DASH NUMBER. 8. "E" LENGTH OF "ØD" MAY BE .002 UNDERSIZE. 9. DRIVE WASHER TO FACILITATE INSTAL;LATION ONLY. NOT PART OF THE INSTALLED FASTENER. DIMENSIONS IN INCHES H ISSUED PER DCN 12947, CHANGED FROM Alcoa Fastening Systems TO Alcoa Fastening Systems & Rings AND AFS TO AFSR 4/19/2004 REVISED 4/7/2015 PAGE 1 OF 3 ® OVERSIZE Unimatic ADVANCED SERIES BLIND BOLT FASTENER, HIGH STRENGTH, PULL-TYPE, POSITIVE MECHANICAL LOCK, 130° FLUSH HEAD, LARGE FOOT PRINT A-286 CRES (95 KSI SHEAR) SINGLE ACTION INSTALLATION, EXPANDED GRIP RANGE PROCUREMENT SPEC T0106 DRAWN BY CHECKED BY J. SCHLOBOHM SIGNATURE ON FILE OUAB130-EU SK12801 This dra win g/docu mentatio n is control led b y either the De pa rtme nt of Sta te, Intern ationa l Tra ffic In Arms R egu la tio ns or the De partmen t of C ommerce , Expo rt Admi nistratio n Reg ula ti ons an d may Req uire a n expo rt li cense /l icen se excep ti on pri or to b ein g tra nsferred to a forei gn na ti ona l, i nsid e or ou tsid e of th e United Sta te s. EAR/ECCN EAR 99. Th ese co mm oditie s, techn olo gy or software we re expo rte d fro m the U nited States in a ccorda nce wi th the Exp ort Ad mini stra ti on Re gul ation s. Dive rsion co ntrary to U.S. la w proh ibited . CURRENT DESIGN ACTIVITY CAGE CODE 0HDW7 AFSR TUCSON OPERATIONS 3724 EAST COLUMBIA STREET TUCSON, ARIZONA 85714 PHONE (520) 519-7400 FAX (520) 519-7454 Alcoa Fastening Systems & Rings THIS DRAWING, THE STRUCTURAL DESIGN DISCLOSED THEREIN AND THE TECHNICAL DATA AND ENGINEERING SERVICE REPRESENTED THEREBY ARE THE EXCLUSIVE PROPERTY OF HUCK INTERNATIONAL, INC. H Unimatic ® ADVANCED BLIND BOLT ENGINEERING STANDARD 10. OVERLAP MINIMUM GRIP FOR -06 DIAMETER IS .140 AND -08 DIAMETER IS NONE. TABLE I I GRIP NUMBER TABULATION DESIGN GRIP GRIP OVERLAP OVERLAP RANGE DASH GRIP GRIP MIN NUMBER MAX MIN. MAX. 02 NONE .094 .157 .173 05 (L) M MAX .351 .491 DESIGN GRIP GRIP OVERLAP OVERLAP RANGE DASH GRIP GRIP MIN NUMBER MAX MIN. MAX. 02 06 08 (L) M MAX (L) M MAX - - .120 .157 .173 .370 .536 NOTE 10 .156 NONE 03 .146 .156 .220 .236 .413 .553 03 .220 .236 .432 .598 .494 .660 04 .209 .219 .282 .298 .476 .616 04 .203 .219 .282 .298 .495 .661 .556 .722 05 .271 .281 .345 .361 .538 .678 05 .265 .281 .345 .361 .557 .723 .619 .785 06 .334 .344 .407 .423 .601 .741 06 .328 .344 .407 .423 .620 .786 .681 .847 07 .396 .406 .470 .486 .663 .803 07 .390 .406 .470 .486 .682 .848 .744 .910 08 .459 .469 .532 .548 .726 .866 08 .453 .469 .532 .548 .745 .911 .806 .972 09 .521 .531 .595 .611 .788 .928 09 .515 .531 .595 .611 .807 .973 .869 1.035 10 .584 .594 .657 .673 .851 .991 10 .578 .594 .657 .673 .870 1.036 .931 1.097 11 .646 .656 .720 .735 .913 1.053 11 .640 .656 .720 .736 .932 1.098 .994 1.160 12 .709 .719 .782 .798 .976 1.116 12 .703 .719 .782 .798 .995 1.161 1.056 1.222 13 .771 .781 .845 .860 1.038 1.178 13 .765 .781 .845 .861 1.057 1.223 1.119 1.285 14 .834 .844 .907 .923 1.101 1.241 14 .828 .844 .907 .923 1.120 1.286 1.181 1.347 15 .896 .906 .970 .985 1.163 1.303 15 .890 .906 .970 .986 1.182 1.348 1.244 1.410 16 .959 .969 1.032 1.048 1.226 1.366 16 .953 .969 1.032 1.048 1.245 1.411 1.306 1.472 17 1.021 1.032 1.094 1.111 1.288 1.428 17 1.015 1.031 1.095 1.111 1.307 1.473 1.369 1.535 18 18 1.078 1.094 1.157 1.173 1.370 1.536 1.431 1.597 19 19 1.140 1.156 1.220 1.236 1.494 1.660 20 20 1.203 1.219 1.282 1.298 1.556 1.722 TABLE I I I OUAB130-EU INSTALLED WEIGHT IN LBS (1000 pcs.) GRIP 5 DIA 6 DIA -02 -03 -04 -05 -06 -07 -08 -09 -10 -11 2.75 3.17 3.54 3.91 4.28 4.65 5.02 5.39 5.76 6.13 4.43 4.91 5.46 6.01 6.56 7.11 7.66 8.21 8.76 9.31 8 DIA GRIP 5 DIA 6 DIA 10.03 10.96 11.89 12.82 13.75 14.68 15.61 16.54 17.47 -12 -13 -14 -15 -16 -17 -18 -19 -20 6.50 6.87 7.24 7.61 7.98 8.35 9.86 10.41 10.96 11.51 12.06 12.61 13.16 8 DIA 18.40 19.33 20.26 21.19 22.12 23.05 23.98 24.91 25.84 DIMENSIONS IN INCHES H ISSUED PER DCN 12947, CHANGED FROM Alcoa Fastening Systems TO Alcoa Fastening Systems & Rings AND AFS TO AFSR 4/19/2004 REVISED 4/7/2015 PAGE 2 OF 3 OVERSIZE Unimatic ® ADVANCED SERIES BLIND BOLT FASTENER, HIGH STRENGTH, PULL-TYPE, POSITIVE MECHANICAL LOCK, 130° FLUSH HEAD, LARGE FOOT PRINT A-286 CRES (95 KSI SHEAR) SINGLE ACTION INSTALLATION, EXPANDED GRIP RANGE PROCUREMENT SPEC T0106 DRAWN BY CHECKED BY J. SCHLOBOHM SIGNATURE ON FILE OUAB130-EU SK12801 This dra win g/docu mentatio n is control led b y either the De pa rtme nt of Sta te, Intern ationa l Tra ffic In Arms R egu la tio ns or the De partmen t of C ommerce , Expo rt Admi nistratio n Reg ula ti ons an d may Req uire a n expo rt li cense /l icen se excep ti on pri or to b ein g tra nsferred to a forei gn na ti ona l, i nsid e or ou tsid e of th e United Sta te s. EAR/ECCN EAR 99. Th ese co mm oditie s, techn olo gy or software we re expo rte d fro m the U nited States in a ccorda nce wi th the Exp ort Ad mini stra ti on Re gul ation s. Dive rsion co ntrary to U.S. la w proh ibited . CURRENT DESIGN ACTIVITY CAGE CODE 0HDW7 AFSR TUCSON OPERATIONS 3724 EAST COLUMBIA STREET TUCSON, ARIZONA 85714 PHONE (520) 519-7400 FAX (520) 519-7454 Alcoa Fastening Systems & Rings THIS DRAWING, THE STRUCTURAL DESIGN DISCLOSED THEREIN AND THE TECHNICAL DATA AND ENGINEERING SERVICE REPRESENTED THEREBY ARE THE EXCLUSIVE PROPERTY OF HUCK INTERNATIONAL, INC. H Unimatic ® ADVANCED BLIND BOLT ENGINEERING STANDARD TABLE I V MATERIAL FINISH CODE SLEEVE PIN LUBE FINISH LOCK COLLAR SLEEVE PIN LOCK COLLAR A-286 CRES PASSIVATE PASSIVATE PASSIVATE A-286 CRES A-286 CRES AMS 5737 NONE AMS2700 & AMS2700 & AMS2700 & OPTIONAL AMS 5737 AMS 5737 OR 316 CRES AMS-QQ-P-35 AMS-QQ-P-35 AMS-QQ-P-35 AMS5690 A-286 CRES ALUMINUM PASSIVATE PASSIVATE A-286 CRES A-286 CRES AMS 5737 D COAT AMS2700 & AMS2700 & OPTIONAL AMS 5737 AMS 5737 OR 316 CRES MIL-DTL-83488 AMS-QQ-P-35 AMS-QQ-P-35 AMS5690 CD CAD. PLATE A-286 CRES PASSIVATE AMS-QQ-P-416 PASSIVATE A-286 CRES A-286 CRES AMS 5737 TYPE I I CLEAR AMS2700 & AMS2700 & OPTIONAL AMS 5737 AMS 5737 OR 316 CRES DICHROMATE AMS-QQ-P-35 AMS-QQ-P-35 AMS5690 CLASS 2 AC A-286 CRES HIKOTE 1 PER PASSIVATE PASSIVATE A-286 CRES A-286 CRES AMS 5737 NAS4006 AND AMS2700 & AMS2700 & OPTIONAL AMS 5737 AMS 5737 OR 316 CRES BMS 10-85 AMS-QQ-P-35 AMS-QQ-P-35 AMS5690 LUBRICATION- WHEN LUBRICATED, PARTS SHALL BE LUBRICATED PER AS5272, AS87132 OR LOX COMPATIBLE DRY FILM LUBRICANT. (MANUFACTURER'S OPTIONS) HUCK PART NUMBER EXAMPLE: OUAB130-EU06 - 04( ) FINISH CODE - SEE TABLE GRIP NUMBER IN 16th INCHES. NOMINAL SHANK DIAMETER IN 32nd INCHES. MATERIAL DESIGNATOR - A286. OVERSIZE Unimatic ® ADVANCED SERIES BLIND BOLT FASTENER, HIGH STRENGTH, PULL-TYPE, POSITIVE MECHANICAL LOCK, 130 FLUSH HEAD, EXPANDED GRIP RANGE. LARGE FOOT PRINT. DRIVE WASHER INCLUDED. DIMENSIONS IN INCHES H ISSUED PER DCN 12947, CHANGED FROM Alcoa Fastening Systems TO Alcoa Fastening Systems & Rings AND AFS TO AFSR 4/19/2004 REVISED 4/7/2015 PAGE 3 OF 3 OVERSIZE Unimatic® ADVANCED SERIES BLIND BOLT FASTENER, HIGH STRENGTH, PULL-TYPE, POSITIVE MECHANICAL LOCK, 130° FLUSH HEAD, LARGE FOOT PRINT A-286 CRES (95 KSI SHEAR) SINGLE ACTION INSTALLATION, EXPANDED GRIP RANGE PROCUREMENT SPEC T0106 DRAWN BY CHECKED BY J. SCHLOBOHM SIGNATURE ON FILE OUAB130-EU SK12801 This dra win g/docu mentatio n is control led b y either the De pa rtme nt of Sta te, Intern ationa l Tra ffic In Arms R egu la tio ns or the De partmen t of C ommerce , Expo rt Admi nistratio n Reg ula ti ons an d may Req uire a n expo rt li cense /l icen se excep ti on pri or to b ein g tra nsferred to a forei gn na ti ona l, i nsid e or ou tsid e of th e United Sta te s. EAR/ECCN EAR 99. Th ese co mm oditie s, techn olo gy or software we re expo rte d fro m the U nited States in a ccorda nce wi th the Exp ort Ad mini stra ti on Re gul ation s. Dive rsion co ntrary to U.S. la w proh ibited .