Available at Digi-Key** www.digikey.com Improved Performance 5x7mm TB / TVB Model Series TCXO / VCTCXO 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com US Headquarters: 630-851-4722 European Headquarters: +353-61-472221 Description: Features: Connor-Winfield's TBxxx and TVBxxx series TV B5 0 10 4 12 are 5x7mm TCXO and .0 MH 42 Z VCTCXO products with exceptional frequency stability and low phase noise. Similar to our Txxx / TVxxx series, these devices are quieter, smoother over temperature and are available at higher frequencies. Using the latest analog TCXO technology, the TBxxx and TVBxxx series have improved phase noise and frequency stability performance and is available in 4-pad or 10pad surface mount footprints. These products are designed for such applications as IEEE 1588 PTP and Synchronous Ethernet. •Frequency Stabilities Available: +/-0.28 ppm (10 to 50 MHz) +/-0.50 ppm, +/-1.00 ppm or +/-2.00 ppm (10 to 100 MHz) •Temperature Ranges Available: 0 to 85°C, 0 to 70°C, -40 to 85°C or -20 to 70°C •Packages Available: TB - Series: 5 x 7mm - 10 Pad TVB - Series: 5 x 7mm - 4 Pad •3.3 Vdc Operation •Output Logic: LVCMOS or Clipped Sinewave •Fixed Frequency - TCXO •Voltage Controlled - VCTCXO •Low Jitter <0.50 ps RMS •Low Phase Noise •Tri-State Enable/Disable: (TB - Model Series Only) •Tape and Reel Packaging •RoHS Compliant / Lead Free Applications: •IEEE 1588 Applications •Synchronous Ethernet slave clocks, ITU-T G.8262 EEC options 1 & 2 •Compliant to Stratum 3, GR-1244-CORE & GR-253-CORE •Wireless Communications •Small Cells •Test and Measurement •GPS Applications Standard Frequencies Available * * 10, 12.8, 19.2, 19.44, 20, 25, 40, 50, 52, 54, 80 and 100 MHz Available frequencies from the factory for small quantity orders or quick delivery. Additional frequencies are available. ** Not all options available at Digi-Key TVB Type / Package TCXO / VCTCXO Series TB = 5.0x7.0 mm 10 Pads TVB = 5.0x7.0 mm 4 Pads Ordering Information 5 Temperature Range 3 = 0 to 85 °C 5 = 0 to 70°C 6 = -40 to 85°C 7 = -20 to 70°C 0 4 Frequency Stability 0 = ±0.28 ppm 1 = ±0.50 ppm 2 = ±1.00 ppm 3 = ±2.00 ppm Features 2 = TCXO, LVCMOS, 3.3 Vdc 3 = TCXO, Clipped Sinewave, 3.3 Vdc 4 = VCTCXO, LVCMOS, 3.3 Vdc 5 = VCTCXO, Clipped Sinewave, 3.3 Vdc - 010.0M Output Frequency Frequency Format -xxx.xM Min -xxx.xxxxxxM Max *Amount of numbers after the decimal point. M = MHz Example: Part Number Bulletin Page Revision Date Tx380 1 of 6 06 14 May 2015 TVB504-010.0M = 5x7mm 4 pad package, ±0.28 ppm, 0 to 70°C, 3.3 Vdc, LVCMOS Output, VCTCXO TB715-012.8M = 5x7mm 10 pad package, ±0.50 ppm, -20 to 70°C, 3.3 Vdc, Clipped Sinewave Output, VCTCXO TB522-050.0M = 5x7mm 10 pad package, ±1.0 ppm, 0 to 70°C, 3.3 Vdc, LVCMOS Output, TCXO TVB602-010.0M = 5x7mm 4 pad package, ±0.28 ppm, -40 to 85°C, 3.3 Vdc, LVCMOS Output, TCXO 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Absolute Maximum Ratings Parameter Storage Temperature Supply Voltage (Vcc) Input Voltage Minimum -55 -0.5 -0.5 Nominal - - - Maximum Units Notes Maximum Units Notes 95 6.0 Vcc + 0.5 °C Vdc Vdc Operating Specifications Parameter Minimum Nominal Output Frequency (Fo) Models TBx0x, TVBx0x 10 - 50 MHz Models TBx1x, TVBx1x 10 - 100 MHz Models TBx2x, TVBx2x 10 - 100 MHz Models TBx3x, TVBx3x 10 - 100 MHz Operating Temperature Range(See Ordering Information for full part number) Models TB3xx, TVB3xx 0 - 85 °C Models TB5xx, TVB5xx 0 - 70 °C Models TB6xx, TVB6xx -40 - 85 °C Models TB7xx, TVB7xx -20 - 70 °C Frequency Calibration @ 25 °C -1.0 - 1.0 ppm 1 Frequency Stability (See Ordering Information for full part number) Per STRATUM 3 GR-1244-CORE Frequency Stability ±0.28 ppm is only available in the frequency range of 10 to 50 MHz. Models TBx0x, TVBx0x -0.28 - 0.28 ppm 2 Holdover Stability -0.32 - 0.32 ppm 3 Constant Temperature Stability -40 - 40 ppb Over 24 Hrs. Frequency Stability(See Ordering Information for full part number) Models TBx1x, TVBx1x -0.50 - 0.50 ppm 2 Models TBx2x, TVBx2x -1.00 - 1.00 ppm 2 Models TBx3x, TVBx3x -2.00 - 2.00 ppm 2 Frequency vs. Load Stability -0.05 - 0.05 ppm ±5% Frequency vs. Voltage Stability -0.05 - 0.05 ppm ±5% Static Temperature Hysteresis - - 0.40 ppm 4 Freq. shift after reflow soldering -1.0 - 1.0 ppm 5 Long Term Stability -1.0 - 1.0 ppm 6 Aging per Life (20 Years) -3.0 - 3.0 ppm per Day -40 - 40 ppb Total Frequency Tolerance -4.6 - 4.6 ppm 7 Supply Voltage (Vcc) 3.135 3.30 3.465 Vdc Supply Current (Icc) LVCMOS (10 to 52 MHz) - 2.1 6.0 mA LVCMOS (>52 to 100 MHz) - - 12 mA Clipped Sine (10 to 52 MHz) - 1.3 2.9 mA Clipped Sine (>52 to 100 MHz) - - 12 mA Jitter: Period Jitter - 3.0 5.0 ps RMS Integrated Phase Jitter (12K to Fo/2) - 0.3 1.0 ps RMS 8 Allan Deviation (1s) - - 1.0E-10 RMS Typical SSB Phase Noise For Fo 10.0 MHz 50.0 MHz 100.0 MHz @ 10 Hz offset -98 -70 -60 dBc/Hz @ 100 Hz offset -125 -100 -91 dBc/Hz @ 1 KHz offset -143 -122 -119 dBc/Hz @ 10 KHz offset -151 -145 -142 dBc/Hz @ 100 KHz offset -152 -150 -153 dBc/Hz @ 1 MHz offset -155 -152 -153 dBc/Hz Start-Up Time - - 10 ms Bulletin Page Revision Date Specifications subject to change without notification. See Connor-Winfield's website for latest revision. All dimensions in inches. © Copyright 2015 The Connor-Winfield Corporation Not intended for life support applications. Tx380 2 of 6 06 14 May 2015 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Control Voltage Input Characteristics ParameterMinimum Minimum Control Voltage 0.3 Frequency Pullability ±10 Pull Slope (Vc=1.65V) - Control Voltage Slope Monotonic Linearity - Input Impedance 100K Modulation Bandwidth (3dB) 10 Nominal Maximum 1.65 3.0 ±12 - 8.00 - Positive Slope - 5 - - - - Units V ppm ppm/V Notes % Ohm KHz OE Enable /Disable Input Characteristics (Pad 8) TB Series only Parameter Enable Voltage (High) Disable Voltage (Low) Function Low: High or Open: Minimum 70%Vcc - Nominal - - Maximum - 30%Vcc Units Vdc Vdc Notes 9 9 Output Disabled (High Impedance) Enabled LVCMOS Output Characteristics Parameter Load (CL) Voltage (High) (Voh) (Low) (Vol) Current(High) (Ioh) (Low) (Iol) Duty Cycle at 50% of Vcc Rise / Fall Time 10% to 90% Minimum Nominal Maximum Units Notes - 90%Vcc - -4 - 45 - 15 - - - - 50 4 - - 10%Vcc - 4 55 8 pF Vdc Vdc mA mA % ns 10 Units Notes Clipped Sinewave Output Characteristics Parameter Minimum Nominal Maximum Load (RC) Output Load Resistance - 10K - Ohm Output Load Capacitance - 10 - pF OutputVoltage(< 40 MHz) 1.0 1.2 - V OutputVoltage(=>40 MHz) 0.8 1.0 - V Output Impedance - 200 - Ohms 11 12 pk-pk pk-pk Package Characteristics Package Hermetically sealed ceramic package with grounded metal cover Environmental Characteristics Vibration: Shock: Soldering Process: Vibration per Mil Std 883E Method 2007.3 Test Condition A. Mechanical Shock per Mil Std 883E Method 2002.4 Test Condition B. RoHS compliant lead free. See soldering profile on page 6. Notes: 1. Initial calibration @ 25°C. ±2°C, for VCTCXO's Vc = 1.65V. Specifications at time of shipment 2. Frequency stability vs. change in temperature. [±(Fmax-Fmin)/(2*Fo]). For VCTCXO's - Vc -= 1.65V 3. Inclusive of frequency stability, supply voltage change (±1%), aging, for 24 hours. Per STRATUM 3 GR-1244-CORE. 4. Frequency change after reciprocal temperature ramped over the operating range. Frequency measured before and after at 25°C 5. Two consecutive solder reflows after 1 hour recovery @ 25°C. 6. Frequency drift over 1 year @ 25°C. 7. Inclusive of calibration @ 25°C, frequency vs. change in temperature, change in supply voltage (±5%), load change (±5%), reflow soldering process and 20 years aging. 8. BW = 12 KHz to 20 MHz 9. Ouput is active with Pad 8 not connected. Leave Pad 8 open if disable function is not required. When disabled, output stage is off but oscillator and compensation circuits are still powered (current consumption <2 mA) 10. Attention: To achieve optimal frequency stability, and in some cases to meet the specification stated on this data sheet, it is required that the circuit connected to this TCXO output must have the equivalent input capacitance that is specified by the nominal load capacitance. Deviations from the nominal load capacitance will have a graduated effect on the stability of approximately 20 ppb per pF load difference. 11.Load components are required for proper operation of the device. 12. Output is AC coupled. Specifications subject to change without notification. See Connor-Winfield's website for latest revision. All dimensions in inches. © Copyright 2015 The Connor-Winfield Corporation Not intended for life support applications. Bulletin Page Revision Date Tx380 3 of 6 06 14 May 2015 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com TB Series Package Outline TB Series Suggested Pad Layout 0.079 Max. (2.0mm) 0.276 ±0.006 (7.0mm) 0.295 (7.49mm) 0.051 (1.28mm) 0.030 (0.76mm) Keep Out Area 0.197 ±0.006 (5.0mm) TB715 1242 12.8 MHZ 8 0.037 (0.94mm) 0.215 (5.46mm) 0.025(6 Places) (0.635mm) Pin 1 1 2 3 10 0.030 (0.762mm) (4 Places) 4 6 5 Top View 10 4 1 2 0.051 (1.28mm) 3 0.040 (1.02mm) (6 Places) 0.100 (2.54mm) Bottom View 9 5 8 0.038 (0.965mm) (4 Places) 7 6 Dimensional Tolerance: ±.005 (.127mm) ±.02 (.508mm) 0.100 (2.54mm) TVB Series Package Outline 0.276 ±0.006 (7.0mm) 1 4 4 0.197 ±0.006 (5.0mm) 3 0.055 (1.40mm) (4 Places) TVB Series Pad Connections 3 0.047 (1.2mm) 4 Places (Top View) 2 Dimensional Tolerance: ±.005 (.127mm) ±.02 (.508mm) Do Not Connect Do Not Connect Do Not Connect Ground Output Do Not Connect Do Not Connect Enable / Disable (OE) Supply Voltage (Vcc VCTCXO: Control Voltage (Vc) TCXO: N/C 0.071 (1.8mm) 4 Places 0.165 (4.2mm) (Bottom View) 1: 2: 3: 4: 5: 6: 7: 8: 9: 10: TVB Series Suggested Pad Layout (Top View) Pad 1 * Do not route any traces in the keep out area. It is recommended the next layer under the keep out area is to be ground plane. 0.079 Max. (2.0mm) TVB504 1242 10.0 MHZ 0.034 (0.90mm) (4 Places) 7 9 TB Series Pad Connections 1 0.224 (5.7mm) 2 Keep Out * Area 1: 2: 3: 4: VCTCXO: Voltage Control (Vc) TCXO: N/C Ground Output Supply (Vcc) * Do not route any traces in the keep out area. It is recommended the next layer under the keep out area is to be ground plane. Alternate TB/TVB Package Height for Select Frequencies: 38.88 MHz, 40 MHz and 50 MHz Bulletin Page Revision Date Specifications subject to change without notification. See Connor-Winfield's website for latest revision. All dimensions in inches. © Copyright 2015 The Connor-Winfield Corporation Not intended for life support applications. Tx380 4 of 6 06 14 May 2015 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com TVB Series Design Recommendations TB Series Design Recommendations Vcc, should have a large copper area for reduced inductance. Connect a 0.01uF bypass capacitor <0.1”(2.54mm) from the pad. 8 6 5 9 Buffer 4 10 1 3 Top View 50 Ohm trace <1”by design Vcc 0.010”(0.254mm) Recommended clearance inductance for internal copper flood. Vcc, should have a large copper area for reduced inductance. Connect a 0.01uF bypass capacitor <0.1”(2.54mm) from the pad. 3 5 1 Top View 2 Top View Ground 50 Ohm Trace Without Output Vias Buffer OSC 50 Ohm trace <1”by design Vcc Buffer Ground 4 10 Ground Ground, should have a large copper area for reduced inductance. 4 9 0.010”(0.254mm) Recommended clearance inductance for internal copper flood. Ground, should have a large copper area for reduced inductance. OSC Top View Ground 50 Ohm Trace Without Output Vias Buffer TOP LAYER GROUND LAYER ....... ....... TOP LAYER GROUND LAYER BOTTOM LAYER BOTTOM LAYER TB Series LVCMOS Test Circuit TVB Series LVCMOS Test Circuit LVCMOS Output Waveform Enable/ Disable DNC DNC Vcc Supply Voltage 8 7 6 9 5 4 10 Vcc Supply Voltage Output 3 4 Ground Ground 1 3 2 1 Output 2 15 pF 0.1 uF Bypass 10 nF Bypass TCXO = N/C VCTCXO = Vc DNC 15 pF 0.1 uF Bypass DNC DNC 10 nF Bypass TCXO = N/C VCTCXO = Vc DNC = Do Not Connect 1V/Div TB Series Clipped Sinewave Test Circuit TVB Series Clipped Sinewave Test Circuit Clipped Sinewave Output Waveform Enable/ Disable DNC DNC Vcc Supply Voltage 8 7 6 9 5 4 10 1 2 Output 10 nF Bypass TCXO = N/C VCTCXO = Vc DNC Output 3 4 Ground Ground 1 2 0 3 10 pF 0.1 uF Bypass Vcc Supply Voltage DNC DNC 10K Ohm 10 pF 0.1 uF Bypass 10 nF Bypass 10K Ohm TCXO = N/C VCTCXO = Vc DNC = Do Not Connect 200 mV/Div Note: The clipped sinewave output is AC coupled Bulletin Page Revision Date Specifications subject to change without notification. See Connor-Winfield's website for latest revision. All dimensions in inches. © Copyright 2015 The Connor-Winfield Corporation Not intended for life support applications. Tx380 5 of 6 06 14 May 2015 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Phase Noise Information TIE Model TVB504-010.0MHz TVB504-010.0M: WANDER GENERATION IN A STRATUM 3 PLL AT 0.098 Hz BANDWIDTH MTIE TVB504-010.0M: MTIE per GR-253-CORE TDEV TVB504-010.0M: TDEV per GR-253-CORE 5x7mm Tape and Reel Information Solder Profile Temperature 260°C 260°C 220°C 180°C 150°C 1 120°C 0 10 s Up to 120 s 60 to 90 s Typical Typical Revision History Revision 00 01 02 03 04 05 06 Date 10/23/12 11/12/12 02/25/13 12/04/13 02/07/14 02/11/14 04/29/15 Meets IPC/JEDEC J-STD-020C Description Data sheet released 10/23/12 Added Digi-Key Increased frequency range to 100 MHz Updated available Frequencies Removed note from Output Freq Updated specifications. Added Additional Package Height for Select Frequencies Specifications subject to change without notification. See Connor-Winfield's website for latest revision. All dimensions in inches. © Copyright 2015 The Connor-Winfield Corporation Not intended for life support applications. Bulletin Page Revision Date Tx380 6 of 6 06 14 May 2015