Din Rail Mount DataSheet ED Series • AC output Solid State Relay in an Industry standard EMR plug in package • Ratings of 1, 3 & 5 Amps • Load voltage range of 24-280VAC • Fits standard DIN rail & PCB mountable sockets • LED input status indicator • AC or DC control • cUL Recognized, IEC Rated, CE & RoHS Compliant • Horsepower Rated, Pilot Duty Rated PRODUCT SELECTION Control Voltage 1A 3A 5A 3-15 VDC Control 18-32 VDC Control 48-72 VDC Control 18-36 VAC Control 90-140 VAC Control ED24D1 ED24C1 ED24D3 ED24C3 ED24F3 ED24D5 ED24C5 ED24F5 ED24E5 ED24B5 AVAILABLE OPTIONS Operational Current 1: 1 Amp (not available with B,E & F suffixes) 3: 3 Amps (not available with B & E suffixes) 5: 5 Amps Output Voltage 24: 24-280 VAC Series ED 24 C 3 R Control Voltage B: 90-140 VAC C: 18-32 VDC D: 3-15 VDC E: 18-36 VAC F: 48-72 VDC Switching Mode Blank: Zero Voltage Turn-On R: Random Turn-On Required for valid part number For options only and not required for valid part number OUTPUT SPECIFICATIONS AC Output (1) Description Operating Voltage (47-63Hz) [Vrms] Transient Overvoltage [Vpk] Maximum Resistive Load Current UL 508/ IEC 62314 LC-A [Arms, FLA] (2) Minimum Load Current [Arms] Maximum Off-State Leakage Current @ Rated Voltage [mArms] Minimum Off-State dv/dt @ Maximum Rated Voltage [V/µsec] (3) Maximum On-State Voltage Drop @ Rated Current [Vpk] Maximum Surge Current (50/60 Hz, 1 cycle) [Apk] Maximum I²t for Fusing (50/ 60 HZ, 1/2 cycle) [A² sec] UL 508 HP/IEC 62314 LC-B Rating @ 240V, 40°C [HP/KW] Minimum Power Factor (with Maximum Load) Do not forget to visit us at: www.crydom.com Copyright © 2015 Crydom Inc. Specifications subject to change without notice. 1A 3A 5A 24-280 600 1.5 0.025 0.1 500 1.1 38/40 7/6 NA 0.5 24-280 600 3 0.15 0.1 500 1.1 240/250 285/260 0.25 / 0.37 0.5 24-280 600 5 0.15 0.1 500 1.1 600/625 1780/1620 0.5 / 0.55 0.5 Din Rail Mount DataSheet INPUT SPECIFICATIONS (1) Description ED24Dx ED24Cx ED24Fx ED24Ex ED24Bx Control Voltage Range Minimum Turn-On Voltage Minimum Turn-Off Voltage Maximum Reverse Voltage Minimum Input Current [mA] Maximum Input Current [mA] Nominal Input Impedance [ohms] Maximum Turn-On Time [msec] (4) Maximum Turn-Off Time [msec] 3-15 VDC 3 VDC 1.9 VDC 6 VDC 3.8 33.8 500 8.33 8.33 18-32 VDC 18 VDC 10.0 VDC 6 VDC 3.8 6.9 4.8K 8.33 8.33 48-72 VDC 48 VDC 24 VDC 6 VDC 3.8 5.8 12.5K 8.33 8.33 18-36 VAC 18 VAC 8 VAC N/A 3.8 8.5 4.5K 20 30 90-140 VAC 90 VAC 48 VAC N/A 3.2 4.9 28K 20 30 GENERAL SPECIFICATIONS (1) Description Parameters Dielectric Strength, Input/Output (50/60Hz) Minimum Insulation Resistance (@ 500 V DC) Maximum Capacitance, Input/Output 3750 Vrms 10 9 Ohms 10 pF -30ºC to 80ºC -40ºC to 125ºC 1.06 oz. (30 g) 85% non-condensing Polyamide Class V0 (UL94) Copper w/Sulfamet Nickel finish Ambient Operating Temperature Range Ambient Storage Temperature Range Weight (typical) Maximum Humidity Housing Material Terminals Material GENERAL NOTES 1) All parameters at 25°C unless otherwise specified. 2) Based on 17mm (5A model) and 13mm (3A model) spacing minimum between parts. 3) Off-State dv/dt test method per EIA/NARM standard RS-443, paragraph 13.11.1 4) Turn-On time for Random turn-on versions is 0.1ms for DC control and 5ms for AC control. MECHANICAL SPECIFICATIONS Tolerances: ±0.02 in / 0.5 mm All dimensions are in: inches [millimeters] AC Output: 5 Amps .99 [25.0] 1.47 [37.4] AC Output: 1 & 3 Amps 1.10 [27.9] .82 [20.8] .02 [0.5] .24 [6.1] .30 [7.6] .20 [5.1] .19 [4.8] .12 [3.0] .21 [5.3] .10 [2.5] 1 2 4 3 5 .39 [9.9] Do not forget to visit us at: www.crydom.com 1.14 [29.0] Copyright © 2015 Crydom Inc. Specifications subject to change without notice. .50 [12.7] Din Rail Mount DataSheet WIRING DIAGRAM -DC 3 1/A1 AC LOAD AC 1 1/A1 Current Limiter A Trigger Circuit AC/DC Converter +DC Trigger Circuit B 2 AC LOAD AC 5/A2 LOAD CAN BE WIRED IN POSITION A or B THERMAL DERATE INFORMATION Load Current (Amps) 6.0 5.0 4.0 5 Amps 3 Amps 1 Amp 2.0 1.0 0 10 20 LOAD 5/A2 Current Limiter 3.0 30 40 50 60 70 AC A B 4 LOAD 80 Ambient Temperature (ºC) Above curve is based on a minimum spacing between parts of 17mm for ED24X5 and 13mm for ED24x3. Maximum current @ 0mm spacing is 2.7A for ED24x5 and 2.3A for ED24x3 @ 40°C. Derating Value: ED24x5 = 0.135A per mm ED24x3 = 0.054A per mm Derating based on Relay air gap: Example: 10mm spacing with a ED24D5 SSR 1.- Subtract spacing from the minimum required spacing of the part (17mm) to get the correction value. 17-10=7 2.- Multiply air gap derating value found above with correction value 0.135 x 7 = 0.945A Now using this final number we can figure out what the maximum current the relay can carry with 10mm spacing @ 60°C Ambient. 3.- using the Ambient Derating Curve above find the current for the 5A model @ 60°C. In this case that calue is 3A. 4.- Subtract the value above (0.945A) from 3A. 3-0.945 = 2.055A The maximum current you can switch with the ED24D5 with a 10mm air gap between relays @ 60°C ambient is 2.055A Do not forget to visit us at: www.crydom.com Copyright © 2015 Crydom Inc. Specifications subject to change without notice. AC Din Rail Mount DataSheet AGENCY APPROVALS Designed in accordance with the requirements of IEC 62314 Pilot Duty Rated C300 IEC 61000-4-2 : Electrostatic Discharge Level 3 – Criteria A IEC 61000-4-4 : Electrically Fast Transients Level 3 – Criteria B IEC 61000-4-5 : Electrical Surges Level 3 – Criteria A E116949 ACCESSORIES ED Series Accessories DRSED PCBSED DIN Rail Mountable Socket Part no.: DRSED Fingersafe IP10 DIN rail mountable socket to mount ED series relays onto standard 35 mm DIN rail. Rated at 250 V AC/DC, 12 Amps. The DRSED includes M3 Combo screws. PC Board Mountable Socket Part no.: PCBSED PC Board mountable socket for ED series relays. Rated at 250 V AC/DC, 12 Amps. Suggested Pin-out hole diameter: 1.0 mm Rev 073015 Do not forget to visit us at: www.crydom.com Copyright © 2015 Crydom Inc. Specifications subject to change without notice. Din Rail Mount DataSheet DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / 危险 HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH. • Disconnect all power before installing or working with this equipment. • Verify all connections and replace all covers before turning on power. Failure to follow these instructions will result in death or serious injury. RIESGO DE DESCARGA ELECTRICA O EXPLOSION. • Desconectar todos los suministros de energia a este equipo antes de trabajar con este equipo. • Verificar todas las conexiones y colocar todas las tapas antes de energizer el equipo. El incumplimiento de estas instrucciones puede provocar la muerte o lesiones serias. RISQUE DE DESCHARGE ELECTRIQUE OU EXPLOSION • Eteindre toutes les sources d'énergie de cet appareil avant de travailler dessus de cet appareil • Vérifier tous connections, et remettre tous couverts en olace avant de mettre sous De non-suivi de ces instructions provoquera la mort ou des lésions sérieuses sérieuses. GEFAHR EINES ELEKTRISCHE N SCHLAGES ODER EINER EXPLOSION. • Stellen Sie jeglichen Strom ab, der dieses Gerät versorgt, bevor Sie an dem Gerät Arbeiten durchführen • Vor dem Drehen auf Energie alle Anschlüsse überprüfen und alle Abdeckungen ersetzen. Unterlassung dieser Anweisungen können zum Tode oder zu schweren Verletzungen führen. RISCHIO DI SCOSSA ELETTRICA O DELL’ESPLOSI ONE. • Spenga tutta l'alimentazion e che fornisce questa apparecchiatu ra prima del lavorare a questa apparecchiatu ra 存在电击、 爆炸或电弧 闪烁危险 • 在操作此设 备之前请先 关闭电源。 若不遵守这些说明， 可能会导致严重的 人身伤害甚至死亡。 • Verificare tutti i collegamenti e sostituire tutte le coperture prima della rotazione sull'alimentazi one L'omissione di seguire queste istruz ioni provocherà la morte o di lesioni serie WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA / 警告 RISK OF MATERIAL DAMAGE AND HOT ENCLOSURE RISQUE DE DOMMAGE MATERIEL ET DE SURCHAUFFE DU BOITIER GEFAHR VON MATERIALSCHÄDEN UND GEHÄUSEERHITZUNG • The product's side panels may be hot, allow the product to cool before touching. • Follow proper mounting instructions including torque values. • Do not allow liquids or foreign objects to enter this product. • Les panneaux latéraux du produit peuvent être chauds. Laisser le produit refroidir avant de le toucher. • Respecter les consignes de montage, et notamment les couples de serrage. • Ne pas laisser pénétrer de liquide ni de corps étrangers à l'intérieur du produit. • Die Seitenwände können heiß sein. Lassen Sie das Produkt abkühlen, bevor Sie es berühren. • Beachten Sie die Montageanweisungen, • Führen Sie keine Flüssigkeiten oder Fremdkörper in das Produkt ein. Le non-respect de cette directive peut entraîner, Failure to follow these instructions can result in des lésions corporelles graves ou des serious injury, or equipment damage. dommages matériels. Die Nichtbeachtung dieser Anweisung kann Körperverletzung oder Materialschäden zur Folge haben. RIESGO DE DAÑOS MATERIALES Y DE SOBRECALENTAMIENTO DE LA UNIDAD RISCHIO DI DANNI MATERIALI E D'INVOLUCRO CALDO 材料损坏和高温外壳的危险性 • Los paneles laterales del producto pueden estar calientes. Esperar que el producto se enfríe antes de tocarlo. • Respetar las instrucciones de montaje, y en particular los pares de apretado. • No dejar que penetren líquidos o cuerpos extraños en el producto. • I pannelli laterali dell'apparecchio possono scottare; lasciar quindi raffreddare il prodotto prima di toccarlo. • Seguire le istruzioni di montaggio corrette. • Non far entrare liquidi o oggetti estranei in questo apparecchio. Si no se respetan estas precauciones pueden producirse graves lesiones, daños materiales. La mancata osservanza di questa precauzione può causare gravi rischi per l'incolumità personale o danni alle apparecchiature. Do not forget to visit us at: www.crydom.com Copyright © 2015 Crydom Inc. Specifications subject to change without notice. • 产品的一侧面板可能很热，在其冷却前请 不要触碰。 • 遵照正确的安装说明，包括扭矩值。 • 请勿让液体及其他异物进入本产品。 如不能正确执行这些操作说明， 极有可能造成严重人体伤害或者设备的损坏。 Din Rail Mount DataSheet ANNEX - ENVIROMENTAL INFORMATION The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People’s Republic of China Electronic Industry Standard SJ/T11364 – 2006, Marking for Control of Pollution Caused by Electronic Information Products. Part Name Toxic or hazardous Substance and Elements Lead (Pb) Mercury (Hg) Cadmium (Cd) Hexavalent Chromium (Cr (VI)) Polybrominated biphenyls (PBB) Polybrominated diphenyl ethers (PBDE) Semiconductor die Solder 附件 - 环保信息 此附件所标示的包括电子信息产品污染图标的环保信息符合中华人民共和国电子行业标准 SJ/T11364 - 2006, 电子信息产品污染控制标识要求。 部件 名称 铅 汞 镉 有毒有害物质或元素 六价铬 多溴联苯 (Pb) (Hg) (Cd) (Cr (VI)) 半导体芯片 焊接点 50 Do not forget to visit us at: www.crydom.com Copyright © 2015 Crydom Inc. Specifications subject to change without notice. (PBB) 多溴二苯醚 (PBDE)