Panel Mount DataSheet Evolution Dual Series • 25A & 50A Output rating per channel @ 40°C • 24 to 280 & 48 to 600VAC Operating voltage • 4-32VDC Control input • Three input termination options • Zero turn-on outputs • Input status LED indicator for each channel • Available with IP20 “Touch-Safe” Covers • UL508 Endurance Rating PRODUCT SELECTION Control Voltage 240V, 25A 240V, 50A 480V, 25A 480V, 50A 4-32 VDC CD2425W2U CD2450W2U CD4825W2U CD4850W2U AVAILABLE OPTIONS Operating Voltage 24: 24-280 VAC 48: 48-660 VAC Series C D 24 Cover C: Included D: Not Included 25 Control Voltage W: 4-32 VDC W 2 Rated Load Current 25: 25 Amps 50: 50 Amps Output Terminal Orientation U: A channel top, B channel bottom V: A channel on left, B channel on right V H Input Connector Thermal Pad 2: Key Locking Connector Blank: Not Included H: Included 3: 4 Pin Connector accepting Screw Terminals 4: 4 Pin Spring Terminal Required for valid part number For options only and not required for valid part number * Not all part number combinations are available. Contact Crydom Technical support for information on the availability of a specific part number. OUTPUT SPECIFICATIONS (1) Description Operating Voltage (47-440Hz) [Vrms] Load Current Range (3) [Arms] Transient Overvoltage [Vpk] Maximum Off-State Leakage Current @ Rated Voltage [mArms] Minimum Off-State dv/dt @ Maximum Rated Voltage [V/µsec] (2) Maximum 1 Cycle Surge Current (50/60) [Apk] Maximum Surge Current 50Hz (20ms) [Apk] Maximum On-State Voltage Drop @ Rated Current [Vpk] Thermal Resistance Junction to Case (Rjc) [°C/W] Maximum I² t for Fusing 50/60Hz (1/2 cycle) [A² sec] Minimum Power Factor (with Maximum Load) Do not forget to visit us at: www.crydom.com Cx2425xxxx Cx2450xxxx Cx4825xxxx Cx4850xxxx 24-280 0.15-25 600 1.0 500 275/300 275 1.3 0.65 380/370 0.5 24-280 0.15-50 600 1.0 500 710/750 710 1.3 0.33 2520/2320 0.5 48-600 0.15-25 1200 1.0 500 275/300 275 1.3 0.65 380/370 0.5 48-600 0.15-50 1200 1.0 500 710/750 710 1.3 0.33 2520/2320 0.5 Copyright © 2015 Crydom Inc. Specifications subject to change without notice. Panel Mount DataSheet INPUT SPECIFICATIONS (1) Description CxxxWxxx Control Voltage Range Minimum Turn-On Voltage Minimum Turn-Off Voltage Typical Input Current Nominal Input Impedance Maximum Turn-On Time [msec] Maximum Turn-Off Time [msec] 4-32 VDC 4 VDC 1 .0 VDC 10 mA @ 12 VDC See Note (4) 1/2 Cycle 1/2 Cycle GENERAL SPECIFICATIONS Description Parameters Dielectric Strength, Input/Output (50/60Hz) Dielectric Strength, Input/Output/Base (50/60Hz) Minimum Insulation Resistance (@ 500 V DC) 4000 Vrms 2500 Vrms 10 9 Ohm 10 pF -40 to 80 °C -40 to 125 °C 3.0 oz (86.5 g) Screw Type Output: 8-32 Output: 20 in lb (2.2Nm) Output:2 x AWG 8 (3.8mm) Maximum Capacitance, Input/Output Ambient Operating Temperature Range Ambient Storage Temperature Range Weight (typical) Terminals Max. Torque Max. Wire Size GENERAL NOTES 1) 2) 3) 4) All parameters at 25°C and per section unless otherwise specified. Off-state dv/dt test method per EIA/NARM standard RS-443, paragraph 13.11.1 Heat sinking required, see derating curves. Input circuit incorporates active current limitation WIRING DIAGRAM SSR Output Configuration "U" Option Top-Bottom Line/Load Connections LOAD A -DC 1 LED +DC 2 Trigger Circuit A2 AC Current Limiter +A -A +B -B A B -DC 3 B1 AC LED +DC 4 AC SUPPLY A1 AC Current Limiter Trigger Circuit B2 AC LOAD B AC SUPPLY Contactor Output Configuration "V" Option Left-Right Line/Load Connections A B L O A D A AC SUPPLY Do not forget to visit us at: www.crydom.com Copyright © 2015 Crydom Inc. Specifications subject to change without notice. +A -A +B -B L O A D B AC SUPPLY Panel Mount DataSheet MECHANICAL SPECIFICATIONS Tolerances: ± 0.02 in / 0.5 m All dimensions are in: inches [millimeters] Mounting Hole/Slot 0.18 [4.5] DIA. Mounting Hole/Slot r 0.09 [2.2] 2.300 [58.42] 1.875 [47.63] .625 [15.89] 8X .191 [4.85] IP20 1.100 [27.94] 1.425 [36.20] .803 [20.40] 1.700 [43.18] 1.800 [45.72] 2X .200 [5.08] 2.635 [66.93] 2.300 [58.42] IP00 1.100 [27.94] 1.150 [29.21] 1.150 [29.21] 1.700 [43.18] .803 [20.40] 1.800 [45.72] MECHANICAL DIMENSIONS (shown without IP20 cover) INPUT CONNECTOR DIMENSIONS SUGGESTED MATING CONNECTORS/PLUGS 3X 0.100 [2.54] 4X 0.026 [0.66] (SQUARE) 1.150 [29.21] 0.200 [5.08] 0.120 [3.05] 0.300 [7.62] Crimp Housing, Positive Latch Molex 050579404 Accepts wires: AWG #24, 0.2 mm² 0.420 [10.67] INPUT CONNECTOR OPTION 2 0.500 [12.71] Vertical Plug, Top Wire entry 3X 0.138 [3.50] 1.059 [26.90] 1.046 [26.58] INPUT CONNECTOR OPTION 3 Molex 039500-0004 Phoenix 1840382 Dinkle EC350V-04P 0.413 [10.50] Vertical Plug, Rear Wire entry 0.157 [4.00] 0.285 [7.25] 0.122 [3.10] 0.606 [15.40] 4X 0.031 [0.80] (SQUARE) Molex 39503-2004 Phoenix 1862878 Dinkle EC350RL-04P Vertical Plug, Front Wire entry Molex 39503-3004 Phoenix 1863178 Dinkle EC350R-04P Vertical Spring Cage Plug, top Wire E Phoenix 1939934 Dinkle 0221-2004 All 4 options accept wires: AWG #16 to 24 N/A 1.201 [30.50] INPUT CONNECTOR OPTION 4 Do not forget to visit us at: www.crydom.com Copyright © 2015 Crydom Inc. Specifications subject to change without notice. Accepts wires: AWG #16 to 24 Panel Mount DataSheet THERMAL DERATE INFORMATION CXXX25XXXX CXXX50XXXX (25 Amps per Channel) (50 Amps per Channel) 100 Combined Load Current [Amps] Combined Load Current [Amps] 50 40 30 20 10 0 80 60 40 20 0 20 30 40 50 60 70 80 Ambient Temperature [°C] 1.0°C/W - HS103 1.5°C/W - HS-2 2.5°C/W - 20 30 40 50 60 70 80 Ambient Temperature [°C] 0.5°C/W - HS053 1.0°C/W - HS103 1.5°C/W - HS-2 AGENCY APPROVALS Designed in accordance with the requirements of IEC 62314 E116950 Do not forget to visit us at: www.crydom.com Copyright © 2015 Crydom Inc. Specifications subject to change without notice. Rev. 091515 Panel Mount DataSheet DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / 危险 HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH. • Disconnect all power before installing or working with this equipment. • Verify all connections and replace all covers before turning on power. Failure to follow these instructions will result in death or serious injury. RIESGO DE DESCARGA ELECTRICA O EXPLOSION. • Desconectar todos los suministros de energia a este equipo antes de trabajar con este equipo. • Verificar todas las conexiones y colocar todas las tapas antes de energizer el equipo. El incumplimiento de estas instrucciones puede provocar la muerte o lesiones serias. RISQUE DE DESCHARGE ELECTRIQUE OU EXPLOSION • Eteindre toutes les sources d'énergie de cet appareil avant de travailler dessus de cet appareil • Vérifier tous connections, et remettre tous couverts en olace avant de mettre sous De non-suivi de ces instructions provoquera la mort ou des lésions sérieuses sérieuses. GEFAHR EINES ELEKTRISCHE N SCHLAGES ODER EINER EXPLOSION. • Stellen Sie jeglichen Strom ab, der dieses Gerät versorgt, bevor Sie an dem Gerät Arbeiten durchführen • Vor dem Drehen auf Energie alle Anschlüsse überprüfen und alle Abdeckungen ersetzen. Unterlassung dieser Anweisungen können zum Tode oder zu schweren Verletzungen führen. RISCHIO DI SCOSSA ELETTRICA O DELL’ESPLOSI ONE. • Spenga tutta l'alimentazion e che fornisce questa apparecchiatu ra prima del lavorare a questa apparecchiatu ra 存在电击、 爆炸或电弧 闪烁危险 • 在操作此设 备之前请先 关闭电源。 若不遵守这些说明， 可能会导致严重的 人身伤害甚至死亡。 • Verificare tutti i collegamenti e sostituire tutte le coperture prima della rotazione sull'alimentazi one L'omissione di seguire queste istruz ioni provocherà la morte o di lesioni serie WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA / 警告 RISK OF MATERIAL DAMAGE AND HOT ENCLOSURE RISQUE DE DOMMAGE MATERIEL ET DE SURCHAUFFE DU BOITIER GEFAHR VON MATERIALSCHÄDEN UND GEHÄUSEERHITZUNG • The product's side panels may be hot, allow the product to cool before touching. • Follow proper mounting instructions including torque values. • Do not allow liquids or foreign objects to enter this product. • Les panneaux latéraux du produit peuvent être chauds. Laisser le produit refroidir avant de le toucher. • Respecter les consignes de montage, et notamment les couples de serrage. • Ne pas laisser pénétrer de liquide ni de corps étrangers à l'intérieur du produit. • Die Seitenwände können heiß sein. Lassen Sie das Produkt abkühlen, bevor Sie es berühren. • Beachten Sie die Montageanweisungen, • Führen Sie keine Flüssigkeiten oder Fremdkörper in das Produkt ein. Le non-respect de cette directive peut entraîner, Failure to follow these instructions can result in des lésions corporelles graves ou des serious injury, or equipment damage. dommages matériels. Die Nichtbeachtung dieser Anweisung kann Körperverletzung oder Materialschäden zur Folge haben. RIESGO DE DAÑOS MATERIALES Y DE SOBRECALENTAMIENTO DE LA UNIDAD RISCHIO DI DANNI MATERIALI E D'INVOLUCRO CALDO 材料损坏和高温外壳的危险性 • Los paneles laterales del producto pueden estar calientes. Esperar que el producto se enfríe antes de tocarlo. • Respetar las instrucciones de montaje, y en particular los pares de apretado. • No dejar que penetren líquidos o cuerpos extraños en el producto. • I pannelli laterali dell'apparecchio possono scottare; lasciar quindi raffreddare il prodotto prima di toccarlo. • Seguire le istruzioni di montaggio corrette. • Non far entrare liquidi o oggetti estranei in questo apparecchio. Si no se respetan estas precauciones pueden producirse graves lesiones, daños materiales. La mancata osservanza di questa precauzione può causare gravi rischi per l'incolumità personale o danni alle apparecchiature. Do not forget to visit us at: www.crydom.com Copyright © 2015 Crydom Inc. Specifications subject to change without notice. • 产品的一侧面板可能很热，在其冷却前请 不要触碰。 • 遵照正确的安装说明，包括扭矩值。 • 请勿让液体及其他异物进入本产品。 如不能正确执行这些操作说明， 极有可能造成严重人体伤害或者设备的损坏。 Panel Mount DataSheet ANNEX - ENVIROMENTAL INFORMATION The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People’s Republic of China Electronic Industry Standard SJ/T11364 – 2006, Marking for Control of Pollution Caused by Electronic Information Products. Part Name Toxic or hazardous Substance and Elements Lead (Pb) Mercury (Hg) Cadmium (Cd) Hexavalent Chromium (Cr (VI)) Polybrominated biphenyls (PBB) Polybrominated diphenyl ethers (PBDE) Semiconductor die Solder 附件 - 环保信息 此附件所标示的包括电子信息产品污染图标的环保信息符合中华人民共和国电子行业标准 SJ/T11364 - 2006, 电子信息产品污染控制标识要求。 部件 名称 铅 汞 镉 有毒有害物质或元素 六价铬 多溴联苯 (Pb) (Hg) (Cd) (Cr (VI)) 半导体芯片 焊接点 50 Do not forget to visit us at: www.crydom.com Copyright © 2015 Crydom Inc. Specifications subject to change without notice. (PBB) 多溴二苯醚 (PBDE)