Panel Mount Datasheet CL Series • Ratings from 5A and 10A @ 24-280 VAC • Triac Output • LED Status Indicator • UL Approved, CE Compliant to EN60950-1 • Improved SEMS screw and washer • Redesigned housing with anti-rotation barriers • AC or DC control • EMC Compliant to Level 3 • Epoxy Free Design For Generation 3 datasheet click here PRODUCT SELECTION Control Voltage 3-32 VDC 90-250 VAC 5A 10A CL240D05 CL240A05 CL240D10 CL240A10 AVAILABLE OPTIONS Control Voltage A: 90-250 VAC D: 3-32 VDC Series CL 240 A Load Voltage 240: 24-280 VAC * Termination Blank: Screws & clamps K: Installed standoffs with Cover screws for PC Board Blank: Not Included (IP00) mounting (IP00 only) (1) C: Included (IP20) Required for valid part number For options only and not required for valid part number Not all part number combinations are available. Contact Crydom Technical Support for information on the availability of a specific part number. K 10 Rated Load Current 05: 5 Amps 10: 10 Amps R C H Switching Type Thermal Pad Blank: Zero Voltage Blank: Not Included Turn-On H: Included R: Instantaneous Turn-On OUTPUT SPECIFICATIONS (2) Description 5A 10A 24-280 600 7 500 5 150 84/100 1.6 2.3 35/42 0.5 3 24-280 600 7 500 10 150 120/126 1.5 2.3 72/66 0.5 1.5 Description DC Control AC Control Control Voltage Range Maximum Reverse Voltage Minimum Turn-On Voltage Must Turn-Off Voltage Minimum Input Current (for on-state) Maximum Input Current Nominal Input Impedance Maximum Turn-On Time [msec] Maximum Turn-Off Time [msec] 3-32 VDC (5) -32 VDC 3 VDC 1 VDC 10 mA 14 mA Current Limited 1/2 Cycle (6) 1/2 Cycle 90-250 VAC 90 VAC 10 VAC 6 mA 10 mA Current Limited 20 30 Operating Voltage (47-63Hz) [Vrms] Transient Overvoltage [Vpk] (3) Maximum Off-State Leakage Current @ Rated Voltage [mArms] Minimum Off-State dv/dt @ Maximum Rated Voltage [V/µsec] Maximum Load Current [Arms] (4) Minimum Load Current [mArms] Maximum 1 Cycle Surge Current (50/60Hz)[Apk] Maximum On-State Voltage Drop @ Rated Current [Vpk] Thermal Resistance Junction to Case (Rjc) [°C/W] Maximum 1/2 Cycle I² t for Fusing (50/60Hz)[A²sec] Minimum Power Factor (with Maximum Load) Minimum Heat Sink for Rated Current @ 40°C [°C/W] INPUT SPECIFICATIONS (2) Do not forget to visit us at: www.crydom.com Copyright © 2016 Crydom Inc. Specifications subject to change without notice. Panel Mount Datasheet GENERAL SPECIFICATIONS (2) Description Parameters Dielectric Strength, Input to Output (50/60Hz) Dielectric Strength, Input/Output to Ground (50/60Hz) Minimum Insulation Resistance (@ 500 VDC) Maximum Capacitance, Input/Output Ambient Operating Temperature Range (7) Ambient Storage Temperature Range Weight (typical) Housing Material Baseplate Material Input Terminal Screw Torque Range (in-lb/Nm) Load Terminal Screw Torque Range (in-lb/Nm) SSR Mounting Screw Torque Range (in-lb/Nm) Input/Load Terminal Screw Torque Range (in-lb/Nm) (1) Input/Output Terminal Screw Thread Size Humidity per IEC60068-2-78 LED Input Status Indicator MTBF (Mean Time Between Failures) at 40°C ambient temperature (8) MTBF (Mean Time Between Failures) at 60°C ambient temperature (8) 4000 Vrms 2500 Vrms 109 Ohms 8 pF -40 to 80 °C -40 to 125 °C 2.88 oz (81.53 g) UL94 V-0 Aluminum 13-15 /1.5-1.7 18-20 / 2-2.2 18-20 / 2-2.2 w/”K” option 8-10 / 0.9-1.13 #6-32 UNC / #8-32 UNC 93% non-condensing Green 11,641,553 hours (1,328 years) 7,210,376 hours (823 years) WIRING DIAGRAM AC V Load (9) 1 ( ) Recommended Wire Sizes Wire Size (Solid / Stranded) Terminals 2 ( ) Input 1 2 OUTPUT 4 INPUT 4 (– / ) Output 3 Trigger Circuit Input Current (mA) 1 AC INPUT 30 [133] 110 [490] 2 x 8 AWG (8.4 mm2) / 8.4 [maximum] 90 [400] 12 Current Limiter 10 8 6 4 2 0 2 AC 0 5 10 15 20 DC Input Voltage 25 30 35 Input Current vs Input Voltage Standar Regulated “AC” Inputs CL Series AC Control 7 Current Limiter Trigger Circuit OUTPUT 1 AC 2 AC Input Current (mA) 6 AC 4 INPUT / 0.518 [minimum] 2 x 10 AWG (5.3 mm2) / 5.3 14 OUTPUT -DC 4 AC 3 90 [400] mm2) Input Current vs Input Voltage Standard Regulated “DC” Inputs CL Series DC Control AC/DC Converter 10 [44.5] 2 x 12 AWG (3.3 mm2) / 3.3 [maximum] 3 (+ / ) EQUIVALENT CIRCUIT BLOCK DIAGRAMS +DC 3 24 AWG (0.2 mm2) / 0.2 [minimum] 20 AWG (0.5 S O L I D S TAT E R E L AY Wire Pull-Out Strength (lbs)[N] 5 4 3 2 1 0 0 50 100 150 AC Input Voltage Do not forget to visit us at: www.crydom.com Copyright © 2016 Crydom Inc. Specifications subject to change without notice. 200 250 Panel Mount Datasheet MECHANICAL SPECIFICATIONS (2) Tolerances: ±0.02 in / 0.5 mm All dimensions are in: inches [millimeters] Screw Termination 1.1 [27.9] 0.49 [12.4] 1 1.88 [47.6] OUTPUT INPUT 1.1 [27.9] 0.49 [12.4] 0.89 [22.6] Mounting Hole/Slot 0.19 [4.9] DIA. 2 1 2.25 [57.3] 1.7 [43.2] S O L I D S TAT E R E L AY 4 Hex Standoff Termination (“K” Option) (1) 1.88 [47.6] OUTPUT INPUT 1.0 [25.4] 1.0 [25.4] 1.75 [44.5] 1.75 [44.5] 1.88 [47.6] 1.7 [43.2] 3 Mounting Hole/Slot 0.19 [4.9] DIA. 2.25 [57.3] 2.32 [58.8] 1.0 [25.4] 1.75 [44.5] 1.22 [30.9] GENERAL NOTES (1) Option “K” is designed and tested for use with printed circuit boards or ring/fork terminals having a thickness between 0.031 and 0.093 inches (0.79 to 2.36 mm). (2) All parameters at 25°C unless otherwise specified. (3) Output will self trigger between 450-600Vpk, not suituable for capacitive loads. (4) Heat sinking required, see derating curves. (5) Increase minimum voltage by 1V for operations from -20 to -40°C. (6) Turn-on time for instantaneous turn-on versions is 0.1 msec. (7) AC models operating range is -20 to 80 °C. (8) All parameters at 50% power rating and 100% duty cycle (contact Crydom tech support for detailed report). (9) Load can be wired to either SSR output terminal 1 or 2. (10) For single surge pulse Tc=25°C; Tj=125°C. For AC Output SSRs, AC Rms value of surge current equals the peak value divided by √2 (1.414). For additional information or specific questions, contact Crydom Technical Support. Do not forget to visit us at: www.crydom.com Copyright © 2016 Crydom Inc. Specifications subject to change without notice. 2.25 [57.3] 1.7 [43.2] Screw Termination, IP20 1.1 [27.9] 0.49 [12.4] 1.04 [26.4] (2 places) 2 S O L I D S TAT E R E L AY 4 3 Mounting Hole/Slot 0.19 [4.9] DIA. 0.93 [23.6] (4 places) 1.0 [25.4] (2 places) Panel Mount Datasheet SURGE CURRENT INFORMATION Single Pulse (10) CL240x10 90 Surge Current (Amp) AC Peak Surge Current (Amp) AC Peak CL240x05 80 70 60 50 40 30 20 10 0 0.01 0.1 1 120 100 80 60 40 20 0 10 0.01 0.1 1 10 Surge Duration (sec) Surge Duration (sec) THERMAL DERATE INFORMATION (i) SSR metal base plate acting as heat sink, it must be exposed to free ambient air. CL240x05 2°C/W 3°C/W CL240x10 1.5°C/W No Heat Sink (i) 4 3 2 1 0 2°C/W No Heat Sink (i) 10 Load Current (Amps) Load Current (Amps) 5 20 30 40 50 60 70 80 8 6 4 2 0 20 Ambient Temperature (ºC) Do not forget to visit us at: www.crydom.com Copyright © 2016 Crydom Inc. Specifications subject to change without notice. 30 40 50 60 Ambient Temperature (ºC) 70 80 Panel Mount Datasheet AGENCY APPROVALS EN60950-1: Meets the requirements of sections1.5: 1,7: 2.9: 2.10.5.3: 4.2: 4.5: 4.7: IEC 61000-4-2 Electrostatic Discharge Level 3 IEC 61000-4-4 Electrically Fast Transients Level 3 IEC 61000-4-5 Electrical Surges Level 3 E46203 ACCESORIES Recommended Accessories New Accessories! Protective Cover & Hardware Kits Protective Cover Part number: KS101 Clear plastic cover compatible with all new S1 designs. Safety covers provide added protection from electric shock when installing or checking equipment. Cover Hardware Kit KS101 HK1 HS501DR 5.0 TRM1 HSP-1 HK4 HS301 / HS301DR 3.0 TRM6 HSP-2 HS251 2.5 HS201 / HS201DR 2.0 HS202 / HS202DR 2.0 HS172 1.7 HS151 / HS151DR 1.5 HS122 / HS122DR 1.2 HS103 / HS103DR 1.0 HS101 1.0 HS073 0.7 HS072 0.7 HS053 0.5 HS033 0.36 HS023 0.25 Hardware Kit Part number: HK4 Bag with 2 square brass accessories and 2 screw 8-32 x 5/8 for output. Used to mount TMR1 lug terminals. Heat Sink Part No. Thermal Resistance Lug Terminal Thermal Pad [ºC/W] Rev. 031516 Do not forget to visit us at: www.crydom.com Copyright © 2016 Crydom Inc. Specifications subject to change without notice. Panel Mount Datasheet DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / 危险 HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH. • Disconnect all power before installing or working with this equipment. • Verify all connections and replace all covers before turning on power. Failure to follow these instructions will result in death or serious injury. RIESGO DE DESCARGA ELECTRICA O EXPLOSION. • Desconectar todos los suministros de energia a este equipo antes de trabajar con este equipo. • Verificar todas las conexiones y colocar todas las tapas antes de energizer el equipo. El incumplimiento de estas instrucciones puede provocar la muerte o lesiones serias. RISQUE DE DESCHARGE ELECTRIQUE OU EXPLOSION • Eteindre toutes les sources d'énergie de cet appareil avant de travailler dessus de cet appareil • Vérifier tous connections, et remettre tous couverts en olace avant de mettre sous De non-suivi de ces instructions provoquera la mort ou des lésions sérieuses sérieuses. GEFAHR EINES ELEKTRISCHE N SCHLAGES ODER EINER EXPLOSION. • Stellen Sie jeglichen Strom ab, der dieses Gerät versorgt, bevor Sie an dem Gerät Arbeiten durchführen • Vor dem Drehen auf Energie alle Anschlüsse überprüfen und alle Abdeckungen ersetzen. Unterlassung dieser Anweisungen können zum Tode oder zu schweren Verletzungen führen. RISCHIO DI SCOSSA ELETTRICA O DELL’ESPLOSIONE. • Spenga tutta l'alimentazione che fornisce questa apparecchiatura prima di lavorare a questa apparecchiatura 存在电击、 爆炸或电弧 闪烁危险 • 在操作此设 备之前请先 关闭电源。 若不遵守这些说明， 可能会导致严重的 人身伤害甚至死亡。 • Verificare tutti i collegamenti e sostituire tutte le coperture prima dell’accensione L'omissione di queste istruzioni provocherà la morte o lesioni serie WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA / 警告 RISK OF MATERIAL DAMAGE AND HOT ENCLOSURE RISQUE DE DOMMAGE MATERIEL ET DE SURCHAUFFE DU BOITIER GEFAHR VON MATERIALSCHÄDEN UND GEHÄUSEERHITZUNG • The product's side panels may be hot, allow the product to cool before touching. • Follow proper mounting instructions including torque values. • Do not allow liquids or foreign objects to enter this product. • Les panneaux latéraux du produit peuvent être chauds. Laisser le produit refroidir avant de le toucher. • Respecter les consignes de montage, et notamment les couples de serrage. • Ne pas laisser pénétrer de liquide ni de corps étrangers à l'intérieur du produit. • Die Seitenwände können heiß sein. Lassen Sie das Produkt abkühlen, bevor Sie es berühren. • Beachten Sie die Montageanweisungen, • Führen Sie keine Flüssigkeiten oder Fremdkörper in das Produkt ein. Le non-respect de cette directive peut entraîner, Failure to follow these instructions can result in des lésions corporelles graves ou des serious injury, or equipment damage. dommages matériels. Die Nichtbeachtung dieser Anweisung kann Körperverletzung oder Materialschäden zur Folge haben. RIESGO DE DAÑOS MATERIALES Y DE SOBRECALENTAMIENTO DE LA UNIDAD RISCHIO DI DANNI MATERIALI E D'INVOLUCRO CALDO 材料损坏和高温外壳的危险性 • Los paneles laterales del producto pueden estar calientes. Esperar que el producto se enfríe antes de tocarlo. • Respetar las instrucciones de montaje, y en particular los pares de apretado. • No dejar que penetren líquidos o cuerpos extraños en el producto. • I pannelli laterali dell'apparecchio possono scottare; lasciar quindi raffreddare il prodotto prima di toccarlo. • Seguire le istruzioni di montaggio corrette. • Non far entrare liquidi o oggetti estranei in questo apparecchio. Si no se respetan estas precauciones pueden producirse graves lesiones, daños materiales. La mancata osservanza di questa precauzione può causare gravi rischi per l'incolumità personale o danni alle apparecchiature. Do not forget to visit us at: www.crydom.com Copyright © 2016 Crydom Inc. Specifications subject to change without notice. • 产品的一侧面板可能很热，在其冷却前请 不要触碰。 • 遵照正确的安装说明，包括扭矩值。 • 请勿让液体及其他异物进入本产品。 如不能正确执行这些操作说明， 极有可能造成严重人体伤害或者设备的损坏。 Panel Mount Datasheet ANNEX - ENVIROMENTAL INFORMATION The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People’s Republic of China Electronic Industry Standard SJ/T11364 – 2006, Marking for Control of Pollution Caused by Electronic Information Products. Part Name Toxic or hazardous Substance and Elements Lead (Pb) Mercury (Hg) Cadmium (Cd) Hexavalent Chromium (Cr (VI)) Polybrominated biphenyls (PBB) Polybrominated diphenyl ethers (PBDE) Semiconductor die Solder 附件 - 环保信息 此附件所标示的包括电子信息产品污染图标的环保信息符合中华人民共和国电子行业标准 SJ/T11364 - 2006, 电子信息产品污染控制标识要求。 部件 名称 铅 汞 镉 有毒有害物质或元素 六价铬 多溴联苯 (Pb) (Hg) (Cd) (Cr (VI)) 半导体芯片 焊接点 50 Do not forget to visit us at: www.crydom.com Copyright © 2016 Crydom Inc. Specifications subject to change without notice. (PBB) 多溴二苯醚 (PBDE)