Rail Mount InstallationDINSheet CKR Series MOUNTING INSTRUCTIONS FEATURES 24 Operating Voltage 24: 24-280 VAC 48: 48-530 VAC 60: 48-660 VAC E Rated Load Current 10: 10 Amps 20: 20 Amps 30: 30 Amps ! Cauti on Tempe ratur e High 80 60 @ 25°C 20 40 Curre nt Ratin g 20A 30 To remove from DIN Rail fig.1 Mounting on DIN Rail P -10 Switching Type Blank: Zero Voltage Turn-On -10: Instantaneous Turn-On Required for valid part number For options only and not required for valid part number Do not forget to visit us at: www.crydom.com 30 10 20 20 40 60 Current Rating 20A @ 25°C 80 ! Caution High Temperature Locate the panel section on which the CKR SSR will be mounted on. Overvoltage Protection Blank: Not Included P: Included 10 Using reasonable force, push CKR in the direction of the arrow shown in fig.1. DIN clip includes tabs for this type of mounting. Tab holes have a diameter of 4.5 mm. You will need two screws (not included) no larger than that to mount the SSR onto panel. Control Voltage D: 4-32 VDC B: 90-140 VAC A: 110-280 VAC AxxxxE: 18-36 VAC D To install on DIN Rail Mounting on Panel PART NUMBER NOMENCLATURE CKR Locate rail and align with non moveable end of CKR DIN clip. For removal pull release tag in direction of arrow using blade of screwdriver and pull it away from DIN rail. Mounting clip incorporates tabs for screw mounting to panel Box Clamp terminals Bracket fits all standard 35 mm DIN rail profiles LED input status indicator Series Mounting on DIN Rail 20 Crydom CKR Series Solid State Relays were developed to offer the advantages of semiconductor switching technology in a standard 22.5 mm industrial package. Quick and easy installation is coupled with low drive power requirements and efficient, reliable power SCR output. This compact new design offers up to 30 Arms in ambient temperatures of 25ºC. Choose one of the two mounting options and follow the instructions below. 10 High Power Ready-to-Use DIN Rail Mounted SSRs Please read all installation instructions before using CKR Series SSRs. Align SSR tabs with panel surface and screw both top and bottom sides. Recommended torque is 12 in-lbs (1.36 Nm). IMPORTANT CONSIDERATIONS Mounting Air Gap (A) To achieve maximum ratings, there must be a minimum spacing of 0.8 in (20 mm) between the devices (horizontally) and of 3.15 in (80 mm) measured between DIN clip tabs (vertically). Earth Bonding (Grounding) The CKR heat sink is equiped with an earth bonding screw as is required for Class 1 Protection, in accordance with EN 60950 (VDE 0804). Recommended torque is 20 in-lbs (2.2 Nm). Rev: 121113 Copyright © 2014 Custom Sensors & Technologies. Specifications subject to change without notice. Rail Mount InstallationDINSheet (+/ ) DERATING CURVES (B) ( / ) The following deating curves must be observed before installation. +3/A1 4/A2 25 Wire Size Maximum wire size of AWG #10 (5.3 mm2) for input and output terminals. Connections Ensure that wires ends are stripped to a minimum length of 0.4 in (10 mm). 20 CKRxxx30xxxx CKRxxx20xxxx CKRxxx10xxxx 15 10 5 SOLID S TAT E C O N TA C T O R 1/L1 2/T1 0 20 40 60 Ambient Temperature (ºC) Recommended Screw Torque Range 5-6 in-lbs (0.6-0.7 Nm) on input and 10-15 in-lbs (1.1-1.7 Nm) on output terminations. 80 Load (A) The air gap is the clearance distance adjacent to either side of the relay or assembly measured to the next closer relay or assembly. (B) 100% Duty Cycle. Rev: 121113 Output Current (Arms) 30 WIRING DIAGRAM