Standard Products UT8SF2M40 80Megabit Flow-thru SSRAM Preliminary Datasheet www.aeroflex.com/memories April 2015 FEATURES Synchronous SRAM organized as 2Meg words x 40bit Continuous Data Transfer (CDT) architecture eliminates wait states between read and write operations Supports 40MHz to 80MHz bus operations Internally self-timed output buffer control eliminates the need for synchronous output enable Registered inputs and outputs for flow-thru operation Single 2.5V to 3.3V supply Clock-to-output time - Clk to Q = 12ns Clock Enable (CEN) pin to enable clock and suspend operation Synchronous self-timed writes Three Chip Enables (CS0, CS1, CS2) for simple depth expansion "ZZ" Sleep Mode option for partial power-down "SHUTDOWN" Mode option for deep power-down Four Word Burst Capability--linear or interleaved Operational Environment - Total Dose: 100 krad(Si) INTRODUCTION The UT8SF2M40 is a high performance 83,886,080-bit synchronous static random access memory (SSRAM) device that is organized as 2M words of 40 bits. This device is equipped with three chip selects (CS0, CS1, and CS2), a write enable (WE), and an output enable (OE) pin, allowing for significant design flexibility without bus contention. The device supports a four word burst function using (ADV_LD). All synchronous inputs are registered on the rising edge of the clock provided the Clock Enable (CEN) input is enabled LOW. Operations are suspended when CEN is disabled HIGH and the previous operation is extended. Write operation control signals are WE and six byte write enables BWE[4:0]. All write operations are performed by internal self-timed circuitry. For easy bank selection, three synchronous Chip Enables (CS0, CS1, CS2) and an asynchronous Output Enable (OE) provide for output tri-state control. The output drivers are synchronously tri-stated during the data portion of a write sequence to avoid bus contention. - SEL Immune: ≤ 100MeV-cm2/mg - SEU error rate: 1.7x10-6 errors/bit-day Package options: - 288-lead CLGA, CCGA, and CBGA Standard Microelectronics Drawing (SMD) 5962-TBD - QMLQ and Q+ pending 36-00-01-005 Ver. 1.0.0 1 Aeroflex Microelectronics Solutions - HiRel ADDR CMD User Command Interface Logic Main Memory Array 2Meg x 40 Housekeeping, and Fault Logic CLK Write Address and Command Queue Write Data Coherency Logic Pipeline Register Write Data Steering Logic Stall Cycle Registers Write Data Queue Read Data Steering and Fault Logic DIN QOUT Figure 1. UT8SF2M40 Block Diagram 36-00-01-005 Ver. 1.0.0 2 Aeroflex Microelectronics Solutions - HiRel Table 1: Pin Definitions NAME DESCRIPTION TYPE CS0 Chip Enable 0, Input, Active LOW: Sampled on the rising edge of CLK. Used in conjunction with CS1 and CS2 to select or deselect the device. Input-Synchronous CS1 Chip Enable 1 Input, Active HIGH: Sampled on the rising edge of CLK. Used in conjunction with CS0 and CS2 to select or deselect the device. Input-Synchronous CS2 Chip Enable 2 Input, Active LOW: Sampled on the rising edge of CLK. Used in conjunction with CS0 and CS1 to select or deselect the device. Input-Synchronous A[20:0] Address Inputs: Sampled at the rising edge of the CLK. A[1:0] is fed to the two-bit burst counter. Input-Synchronous BWE[4:0] Byte Write Enable, Active LOW: Qualified with WE, allows writes to each of six bytes of memory when active, and masks input data when disabled. Input-Synchronous WE Write Enable Input, Active LOW: Sampled on the rising edge of CLK if CEN is active LOW. This signal must be enabled LOW to initiate a write sequence. Input-Synchronous ADV_LD Advance/Load Input: Advances the on-chip address counter or loads a new address. When HIGH (and CEN is enabled LOW) the internal burst counter is advanced. When LOW, a new address can be loaded into the device for an access. After deselection, drive ADV_LD LOW to load a new address. Input-Synchronous CLK Clock Input: Used to capture all synchronous inputs to the device. CLK is qualified with CEN. CLK is only recognized if CEN is active LOW. Input-Clock OE Output Enable, Asynchronous Input, Active LOW: Combined with the synchronous logic block inside the device to control the direction of the I/O pins. When LOW, the I/O pins are enabled to behave as outputs. When disabled HIGH, I/O pins are tri-stated, and act as input data pins. OE is masked during the data portion of a write sequence, during the first clock when emerging from a deselected state and when the device is deselected. Input-Asynchronous CEN Clock Enable Input, Active LOW: When enabled LOW, the clock signal is recognized by the SSRAM. When deasserted HIGH, the clock signal is masked. Because deasserting CEN does not deselect the device, CEN can be used to extend the previous cycle when required. Input-Synchronous DQ[47:0] Bidirectional Data I/Os: As inputs, DQ[47:0] feed into an on-chip data register that is triggered by the rising edge of CLK. As outputs, DQ[47:0] delivers the data contained in the memory location specified by the addresses presented during the previous clock rise of the read cycle. The direction of the pins is controlled by OE. When OE is enabled LOW, the pins behave as outputs. When HIGH, DQs are placed in a tri-state condition. The outputs are automatically tri-stated during the data portion of a write sequence, during the first clock when emerging from a deselected state, and when the device is deselected, regardless of the state of OE. Aeroflex recommends connecting all DQ pins to either VDDQ or VSS through a >10kΩ resistor. Reset Input, Active Low: Resets device to known configuration. Reset is required at initial power-up, after exiting shutdown mode, or after any power interruption. I/O-Synchronous RESET 36-00-01-005 Ver. 1.0.0 3 Input-ASynchronous Aeroflex Microelectronics Solutions - HiRel Table 1: Pin Definitions NAME DESCRIPTION TYPE ZZ ZZ “Sleep” Input, Active HIGH: When HIGH, places the device in a nontime critical “sleep” condition with data integrity preserved. During normal operation, this pin must be LOW. Input-Synchronous SHUTDOWN Shutdown Input, Active HIGH: When HIGH, places device in shutdown mode. System clock can be stopped. Memory contents are not retained. Input-Asynchronous READY1 Device Ready Output: READY outputs a HIGH when device is available for normal operations. READY outputs a LOW when requesting an idle cycle or during power up initialization. Output-Synchronous MODE2 Mode Input: Established at power up. Selects the burst order of the device. When tied to VSS selects linear burst sequence. When tied to VDDQ selects interleaved burst sequence. Input-DC EXTRES2 Input-DC VDD Input Current Reference: Provided for external precision current reference resistor connection. Power supply inputs to the core of the device. VDDQ Power supply for the I/O circuitry. Power Supply I/O Power Supply VSS Ground inputs to the core of the device. VSSQ Ground for I/O circuitry. NUIL Not used Input Low: Pins designated as NUIL need to be externally connected by user to VSSQ through a >10kΩ±10% resistor. -- NUIH Not used Input High: Pins designated as NUIH need to be externally connected by user to VDDQ through a >10kΩ±10% resistor. -- No Connects. Not internally connected to the die. --- NC Ground I/O Ground TDO3 JTAG Circuit Serial Data Output: Package pin requires a pull-up through >10kΩ±10% resistor to VDDQ. JTAG Serial Output Synchronous TDI3 JTAG Circuit Serial Data Input: Device pin internally connected through a 75kΩ±10% resistor to VDDQ. JTAG Serial Input Synchronous TMS3 JTAG Controller Test Mode Select: Device pin internally connected through a 75kΩ±10% resistor to VDDQ. Test Mode Select Synchronous TCK3 JTAG Circuit Clock Input: Package pin requires a pull-up through >10kΩ±10% resistor to VDDQ. JTAG Clock Note: 1. Reference application note AN-MEM-004 for additional READY signal information. 2. DC inputs are established at power up and cannot be switched while power is applied to the device. 3. Reference application note AN-MEM-005 for JTAG operations. JTAG operations are intended for terrestrial use and not guaranteed in radiation environment. 36-00-01-005 Ver. 1.0.0 4 Aeroflex Microelectronics Solutions - HiRel DEVICE OPERATION The UT8SF2M40 is synchronous flow-thru SSRAM designed specifically to eliminate wait states during Write/Read or Read/ Write transitions. All synchronous inputs and outputs are registered on the rising edge of clock. The clock signal is enabled by the Clock Enable input (CEN). When CEN is HIGH, the clock signal is disregarded and all internal states are maintained. All synchronous operations are qualified by CEN. Once power-up requirements have been satisfied, the input clock may only be stopped during sleep (ZZ is HIGH) or shutdown mode (SHUTDOWN is HIGH). Maximum access delay from the rising edge of clock (tCQV) is 12ns (80 MHz device). Burst Read Accesses The UT8SF2M40 has an internal burst counter allowing up to four reads to be performed from a single address input. A new address can only be loaded when ADV_LD is driven LOW. New addresses are loaded into the SSRAM, as described by the Single Read Access section. The burst counter operates in either linear or interleave and is controlled by the MODE input at power up. When MODE pin is LOW, the burst sequence is linear. The burst sequence is interleaved when MODE is HIGH. A0 and A1 are controlled by the burst counter. The burst counter will wrap around when needed. The burst counter increments anytime ADV_LD is HIGH and CEN is low. The operation selected by the state of WE is latched at the beginning of the sequence and maintained throughout. Access is initiated by asserting all three Chip Enables (CS0, CS1, CS2) active at the rising edge of the clock with Clock Enable (CEN) and ADV_LD asserted LOW. The address presented to the device will be registered. Access can be either a Read or Write operation, depending on the status of the Write Enable (WE). Single Write Accesses A write access is initiated when the following device inputs are present at rising clock edge: CEN is enabled LOW, CS0, CS1, and CS2 are all enabled, the Write Enable input signal WE is enabled LOW and ADV_LD is asserted LOW. The addresses present at the address inputs A[20:0] are registered and presented to the memory core. Data I/Os are tri-stated at the next rising edge of clock regardless of state of OE. The write is completed after the next rising clock edge using data present on DQ pins. Each byte of data is individually qualified by its applicable byte write enable input (see Table 2). When the input low, the applicable DQ inputs are registered to memory. When the input is high, the applicable DQ pins are ignored. Write operations are initiated by the Write Enable (WE) input. All write commands are controlled by built in synchronous self-timed circuitry. Three synchronous Chip Enables (CS0, CS1, CS2) and an asynchronous Output Enable (OE) simplify memory depth expansion. All operations (Reads, Writes, and Deselects) are pipelined. ADV_LD must be driven LOW once the device has been deselected in order to load a new address and command for the next operation. To avoid bus contention data should not be driven to DQs when outputs are active. The Output Enable (OE) may be disabled HIGH before applying data to the DQ lines. This will tri-state the DQ output drivers. As an additional feature DQ lines are automatically tri-stated during the data portion of a Write cycle, regardless of the state of OE. Single Read Accesses A read access is initiated when the following device inputs are present at rising clock edge: CEN is enabled LOW, CS0, CS1, and CS2 are all enabled, the Write Enable input signal WE is disabled HIGH and ADV_LD is asserted LOW. The addresses present at the address inputs A[20:0] are registered and presented to the memory. Data propagates to the input of the output register. Data will be available to the bus 12ns after the next rising clock edge provided OE is enabled LOW. After the first clock of the read access, the output buffers are controlled by OE and the internal control logic. OE must be enabled LOW to drive requested data. During the next rising clock, any operation (Read/Write/Deselect) may be initiated. 36-00-01-005 Ver. 1.0.0 Burst Write Accesses The UT8SF2M40 has an internal burst counter allowing up to four writes to be performed from a single address input. A new address can only be loaded when ADV_LD is driven LOW. New addresses are loaded into the SSRAM, as described in the Single Write Access section. When ADV_LD is driven HIGH on the subsequent clock rise, where CEN is LOW, the Chip Enables (CS0, CS1, CS2) and WE inputs are ignored and the burst counter is incremented. The BWE[4:0] inputs must be LOW in each cycle of the burst write in order to qualify each respective byte of data. 5 Aeroflex Microelectronics Solutions - HiRel contents are not maintained in shutdown mode. The SSRAM requires a reset cycle upon exiting shutdown mode. READY Status The UT8SF2M40 device operates as a Synchronous SRAM device. Data integrity housekeeping activities are performed in the background during normal user activity. These housekeeping activities are performed on a regular basis. However, when a housekeeping activity sequence cannot be completed due to user conflict for memory space, the READY pin asserts signifying to the user that an idle cycle is required. Please reference applications note AN-MEM-004 for more information. Table 3. Linear Burst Address Table (MODE=VSS) Byte Write Enables BWE[4:0] The UT8SF2M40 device employs six byte write enable inputs to be used in conjunction with WE to qualify each associated byte of data into the memory. When WE is HIGH, the device is in read mode where all BWE[4:0] are don’t cares. When WE is LOW, each BWE[4:0] must also be low to write the associated data input pins into memory. Data input pins whose associated byte write enable pin is HIGH, will be masked. Data Input Pins BWE0 DQ[7:0] BWE1 DQ[15:8] BWE2 DQ[23:16] BWE3 DQ[31:24] BWE4 DQ[39:32] Third Address Fourth Address A1, A0 A1, A0 A1, A0 A1, A0 00 01 10 11 01 10 11 00 10 11 00 01 11 00 01 10 Starting Address Second Address Third Address Fourth Address A1, A0 A1, A0 A1, A0 A1, A0 00 01 10 11 01 00 11 10 10 11 00 01 11 10 01 00 Power Up/ Down Requirements The SSRAM requires that VDD < VDDQ at all times. The SSRAM does require the user to provide an external reset after initial power application, exiting shutdown mode, or any power interruption to the device input voltage outside the specified limit. Performing a reset requires the assertion of the RESET device input lead (LOW) for a minimum of 1us (tRLRH). After the RESET input is returned HIGH, the device requires 50us (tSHTDWNREC) to complete the reset operation. Once the reset operation is complete, the device requires an additional 20us (tCR) to synchronize the clock input, providing a stable input clock is present. The device READY output lead asserts HIGH once tCR is satisfied at the next rising clock. The READY out lead HIGH indicates the device is available for normal operations. For power down it is required that VDD and VDDQ be powered down to <0.5V for a minimum of 100ms. Sleep Mode The ZZ input lead is a synchronous input. Asserting the ZZ pin HIGH places the SSRAM into a power conservative "sleep" mode. To assure the completion of previous commands and through the pipeline prior to entering sleep mode, a minimum of two full clock cycles (tZZS) are required between the last operation command and asserting the ZZ input. While in sleep mode, data integrity is guaranteed. Changing the input clock frequency or halting the input clock may be executed during sleep mode. The device must be deselected prior to entering sleep mode and remain deselected for the duration of tZZREC after the ZZ input returns LOW. Clock Conditioning Requirements The CLK signal input requirements are given in the Clock section of the AC Characterizations. AC Characterization performances listed herein are based on providing a clock input signal meeting these requirements. Shutdown Mode The SHUTDOWN input pin is an asynchronous input. Asserting SHUTDOWN places the device in a power saving shutdown mode. The system clock can be stopped. Memory 36-00-01-005 Ver. 1.0.0 Second Address Table 4. Interleaved Burst Address Table (MODE=VDDQ) Table 2. Byte Write Enable to Data Input Pins Byte Write Enable Input Starting Address 6 Aeroflex Microelectronics Solutions - HiRel Changing Clock Frequencies The CLK input frequency should be established at a power on, and may only be changed while in SLEEP mode (reference Table 6). Table 5. External Bias Conditions Signal Name External Connections A precision 25kohm < +0.2% low TCR < 25ppm/oC resistor is required to be connected between device pin EXTRES (R15) and VSS. In order to ensure proper operation in conjunction with JTAG boundary scan (reference applications note MEM-AN-005), Aeroflex requires that specific package pins be biased through soft connections to either VDDQ or VSSQ. Table 5 is a list of these required external biases. NUIH2 TDO TCK Package Pin H1, H20, N1, N2, N19, N20, P13, R7, R8, R10, R12, R13, R14, R16 P16, R8 R5 R9 DQ[47:0]3 ref Table 7 NUIL1 Bias Condition >10kΩ to VSSQ >10kΩ to VDDQ >10kΩ to VDDQ >10kΩ to VSSQ >10kΩ to VDDQ or VSSQ Notes: 1. NUIL = Not Used Input Low 2. NUIH = Not Used Input High 3. Aeroflex recommends connecting all DQ[47:0] to either VDDQ or VSSQ through >10kΩ resistors. Table 6: Truth Table for UT8SF2M40[1,2,3,4,5,6,7] Address Used CSx* ZZ SHUT DOWN ADV_LD WE BWEx OE CEN CLK DQs Standby Mode None H L L L X X X L L-H 3-State Continue Deselect None X L L H X X X L L-H 3-State Read Cycle (Start Burst) External L L L L H X L L L-H Data Out Read Cycle (Cont. Burst) Next X L L H X X L L L-H Data Out NOP/Dummy Read (Start) External L L L L H X H L L-H 3-State NOP/Dummy Read (Cont.) Next X L L H X X H L L-H 3-State Write Cycle (Start Burst) External L L L L L L X L L-H Data In Write Cycle (Cont. Burst) Next X L L H X L X L L-H Data In Dummy Write (Start) None L L L L L H X L L-H 3-State Dummy Write (Cont. Burst) Next X L L H X H X L L-H 3-State Clock Inhibit (Stall) N/A X L L X X X X H L-H N/A Sleep Mode N/A H H L X X X X X X 3-State Shutdown Mode None X X H X X X X X X 3-State Operation Notes: * All chip selects active when L, at least one chip select inactive when H 1. X = “Don't Care”, H = Logic HIGH, L = Logic LOW. 2. Write is defined by WE and BWEx 3. When a Write cycle is detected, all I/Os are tri-stated. 4. The DQ pins are controlled by the current cycle and the OE signal. 5. CEN = H inserts wait states. 6. Device will power-up deselected and the I/Os in a tri-state condition, regardless of OE. 7. OE is asynchronous and is not sampled with the clock rise. It is masked internally during Write cycles. During a Read cycle DQs = tri-state when OE is inactive or when the device is deselected and DQs = data when OE is active. 36-00-01-005 Ver. 1.0.0 7 Aeroflex Microelectronics Solutions - HiRel Table 7. 288-Lead Pipelined Signal Locations 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 VDDQ CS2 WE VSS A10 A8 A4 A18 A19 A14 A15 A2 A0 CS0 VSS BWE1 VSS VSS OE BWE2 A11 A9 A6 A17 VSS A20 A16 A13 A12 A1 ZZ BWE3 SHUT DOWN VSS C VDDQ VSSQ VSS READY BWE0 BWE4 A7 A5 VSS VDD VSS VSSQ VDD VDD A3 ADV_LD CS1 VSS VSSQ D DQ33 DQ35 VDD VSS VSS VDD VDD VSS VDD VDD VSSQ VDDQ VDD VSS VSS VDD VDDQ DQ32 E DQ37 DQ1 DQ39 VDD VSSQ VSS VSS VSS VSS VSSQ VDDQ VSS VSS VSSQ VDD DQ38 DQ36 DQ34 F DQ3 DQ5 DQ7 VDDQ VDDQ VSSQ VSS VSS VDD VSS VDD VSS VSS VDDQ VSSQ VDDQ VDDQ DQ4 DQ0 DQ2 G DQ9 DQ11 DQ13 VDD VSSQ VDD VDDQ VDD VSS VDD VSS VDD VDDQ VSSQ VDD VSSQ VDD DQ10 DQ6 DQ8 H NUIL3 DQ15 CEN VSS VSS VDD VDD VDD VSS VSS VSS VDD VDD VSS VSS VSS VSS CLK DQ12 NUIL J DQ19 DQ17 DQ21 VDD VSSQ VDD VSS VDD VSS VDD VSS VDD VSS VSSQ VDD VSSQ VDD DQ14 DQ16 DQ18 K DQ27 DQ25 DQ23 VDDQ VDDQ VSSQ VSS VDDQ VDD VSS VDD VDDQ VSS VDDQ VSSQ VDDQ VDDQ DQ20 DQ24 DQ22 L DQ31 DQ41 DQ29 VDD VSSQ VSS M DQ45 DQ47 DQ43 VDD N NUIL3 NUIL3 VSS P A B R VSS VDDQ VSSQ VSSQ VDDQ 19 20 VDD VSSQ VDDQ VSS VSS VSS VSSQ VDDQ VSS VSS VSSQ VDD DQ26 DQ30 DQ28 VSS VSSQ VDDQ VSSQ VDD VSS VDD VDD VSSQ VDDQ VSSQ VSS VDD DQ40 DQ44 DQ42 VSS VDD VDDQ VSSQ VDD VSS VDD VSS VSS VDD VSSQ VSSQ VDD VSS DQ46 NUIL3 NUIL3 VSS VDD VDDQ VSSQ VSSQ VSSQ VSS VSS VDDQ MODE NUIL3 VDDQ TMS NUIH4 VSSQ VSS VDD TDI TDO1 VDD NUIL3 NUIH4 TCK2 NUIL3 RESET NUIL3 NUIL3 NUIL3 VDDQ VDD NUIL3 EXTRES VSS Notes: 1. Pin requires pull-up to VDDQ of >10kΩ±10%. 2. Pin requires pull-down to VSS of >10kΩ±10%. 3. NUIL = Not used Input Low. NUIL pins requires >10kΩ±10% pull-down to VSSQ. 4. NUIH = Not Used Input High. NUIH pins requires >10kΩ + 10% pull-up to VDDQ. 36-00-01-005 Ver. 1.0.0 8 Aeroflex Microelectronics Solutions - HiRel ABSOLUTE MAXIMUM RATINGS1 (Referenced to VSS) SYMBOL VDD/VDDQ PARAMETER Supply Voltage2 VALUE UNIT -0.5 to 4.0 V -0.3 to VDDQ+0.3 V VIN Voltage on any pin2 IIO DC I/O current per pin @ TJ = 135o for 15 years +10 mA PD Package power dissipation permitted @ TC = 105°C3 15 W TJ Maximum junction temperature ΘJC Thermal resistance junction to case TSTG Storage temperature o +150 3 -65 to +150 C o C/W o C Notes: 1. Permanent device damage may occur if absolute maximum ratings are exceeded. Functional operation should be restricted to recommended operating conditions. 2. All voltages are referenced to VSS. 3. Per MIL-STD-883, Method 1012, Section 3.4.1 PD = (TJ(max) - TC(max)) ΘJC OPERATIONAL ENVIRONMENTS PARAMETER LIMIT UNITS 100 krad(Si) 1.7x10-6 Errors/Bit-Day ≤ 100 MeV-cm2/mg Total Ionizing Dose (TID) Heavy Ion Error Rate 1 Single Event Latchup (SEL) Immune2 Notes: 1. Adams 90% worst case environment, Geosynchronous orbit, 100mils of aluminum 2. Temperature = 105oC; VDD and VDDQ = 3.6V RECOMMENDED OPERATING CONDITIONS SYMBOL LIMITS VDD Core supply voltage 2.3V to VDDQ VDDQ I/O power supply voltage 2.3V to 3.6V TC Case temperature range VIN DC input voltage TJ 36-00-01-005 Ver. 1.0.0 PARAMETER -55°C to +105°C 0V to VDDQ Junction Temperature 9 -55°C to +125°C Aeroflex Microelectronics Solutions - HiRel DC ELECTRICAL CHARACTERISTICS (Pre and Post-Radiation)* (VDD= 2.3V to VDDQ, VDDQ = 2.3 to 3.6V; Unless otherwise noted, Tc is per the temperature range ordered) PARAMETER DESCRIPTION CONDITION MIN MAX UNIT VDD Core Power Supply Voltage 2.3 VDDQ V VDDQ I/O Power Supply Voltage 2.3 3.6 V VOH Output HIGH Voltage VOL VIH VIL Output LOW Voltage Input HIGH Voltage Input LOW Voltage For 3.0V I/O, IOH=-4mA 0.8 * VDDQ V For 2.3V I/O, IOH=-1mA 2.0 V For 3.0V I/O, IOL=8mA 0.4 V For 2.3V I/O, IOL=1mA 0.4 V For 3.0V I/O 2.0 V For 2.3V I/O 1.7 V For 3.0V I/O 0.8 V For 2.3V I/O 0.7 V 2 μA 2 μA IIN1 Input Leakage Current VIN = VDDQ and VSS Except device pins TDI and TMS IIN2 Input Leakage Current VIN = VDDQ Device pins TDI and TMS -2 VIN = VSS Device pins TDI and TMS μA -100 Three-State Output Leakage Current VDD, VDDQ = (Max), VO = VDDQ and VSS, OE = VDDQ (Max) -2 2 μA IOS1,2 Short-Circuit Output Current VDD, VDDQ = (Max), VO = VDDQ and VSS -100 100 mA IDD3 VDD Supply Current in Active Mode VDD, VDDQ = (Max), IOUT = 0mA, 105oC 900 mA -55oC and 25oC 750 mA 105oC 100 mA -55oC and 25oC 100 mA 105oC 250 mA -55oC and 25oC 200 mA IOZ f = fmax IDDQ3 VDDQ Supply Current in Active Mode VDD, VDDQ = (Max), IOUT = 0mA, f = fmax ISHTDWN3 36-00-01-005 Ver. 1.0.0 VDD Supply Current in Shutdown Mode VDD, VDDQ = (Max), VIN > VIH or VIN < VIL, SHUTDOWN > VIH 10 Aeroflex Microelectronics Solutions - HiRel ISHTDWNQ3 ISTBY3 VDDQ Supply Current in Shutdown Mode VDD Supply Current in Standby Mode 105oC 15 mA VIN > VIH or VIN < VIL, SHUTDOWN > VIH -55oC and 25oC 15 mA VDD, VDDQ = (Max), VIN > VIH or VIN < VIL, 105oC 650 mA -55oC and 25oC 500 mA 105oC 100 mA -55oC and 25oC 100 mA 105oC 500 mA -55oC and 25oC 350 mA 105oC 85 mA -55oC and 25oC 85 mA VDD, VDDQ = (Max), f = fmax, device deselected ISTBYQ3 IZZ3 IZZQ3 VDDQ Supply Current in Standby Mode VDD, VDDQ = (Max), VIN > VIH or VIN < VIL, f = fmax, device deselected VDD Supply Current in Sleep Mode VDD, VDDQ = (Max), VIN>VIH or VIN < VIL, ZZ > VIH, SHUTDOWN < VIL VDDQ Supply Current in Sleep Mode VDD, VDDQ = (Max), VIN>VIH or VIN < VIL, ZZ > VIH, SHUTDOWN < VIL CAPACITANCE SYMBOL PARAMETER MIN MAX UNIT CIN4 Input Capacitance 15 pF CI/O4 I/O Capacitance 15 pF Notes: * For devices procured with a total ionizing dose tolerance guarantee, the post-irradiation performance is guaranteed at 25oC per MIL-STD-883 Method 1019, Condition A up to the maximum TID level procured. 1. Supplied as a design limit but not guaranteed nor tested. 2. Not more than one output may be shorted at a time for maximum duration of one second. 3. Post-irradiation limits are the 105oC limits when specified. 4. Measured only for initial qualification and after process or design changes that could affect this parameter. 36-00-01-005 Ver. 1.0.0 11 Aeroflex Microelectronics Solutions - HiRel AC CHARACTERISTICS (Pre and Post-Radiation)* (VDD= 2.3V to VDDQ, VDDQ = 2.3 to 3.6V; Unless otherwise noted, Tc is per the temperature range ordered.)1 PARAMETER tPowerup 2 DESCRIPTION MIN MAX UNIT VDD to first valid command (READ or WRITE) 100 ms Clock (CLK) cycle time 12.5 25.0 ns Clock tCYC6 tCH CLK HIGH time 0.4 * tCYC 0.6 * tCYC ns tCL CLK LOW time 0.4 * tCYC 0.6 * tCYC ns tr, tf2 tclkPJ3,5 tclkCCJ3,5 Input clock rise/fall time (10-90%) 2.25 Input clock period jitter -100 Input clock cycle to cycle jitter V/ns 100 ps 150 ps Setup Times tAS Address setup time prior to CLK 2.5 ns tDS Data setup time prior to CLK 1.5 ns tCENS Clock enable setup (CEN) time prior to CLK 3 ns tWES Write enable (WE) setup time prior to CLK 3 ns tBWES Byte Write enable (BWE[4:0]) setup time prior to CLK 3 ns 2.5 ns 3 ns tADVLDS tCSS Advance load (ADV_LD) setup time prior to CLK Chip select (CSx) setup time prior to CLK Hold Times tAH Address hold time after CLK 1.2 ns tDH Data hold time after CLK 1.4 ns tCENH CEN hold time after CLK 1.2 ns tWEH WE hold time after CLK 1.5 ns tBWEH Byte Write enable (BWE[4:0]) hold time after CLK 1.5 ns ADV_LD hold time after CLK 0.9 ns CSx hold time after CLK 1.8 ns tADVLDH tCSH Output Times tCQV4 Data valid after rising CLK 12 ns tOEQV4 Output enable (OE) active to data valid 4.0 ns tCQOH Data output hold time after rising CLK tCQZ5 Rising CLK to output three-state time tCQX5 Rising CLK to output enable time 36-00-01-005 Ver. 1.0.0 12 2.0 ns 5.0 1.3 ns ns Aeroflex Microelectronics Solutions - HiRel tOEQZ5 OE inactive to output three-state time tOEQX5 OE active to output enable time 4.5 0 ns ns Notes: * For devices procured with a total ionizing dose tolerance guarantee, the post-irradiation performance is guaranteed at 25oC per MIL-STD-883 Method 1019, Condition A up to the maximum TID level procured 1. AC Characteristics based on compliance with CLOCK input specifications 2. Supplied as a design guideline, not tested or guaranteed. 3. Period and Cycle to Cycle jitter is defined by JEDEC Standard 65B 4. Maximum data output valid times guaranteed up to 25pf load capacitance. For loads >25pf, a derating factor of parameter = [specification max(ns) + (CLoad 25pF)(44.2ps/pF]. 5. Guranteed by design. 6. Maximum Cycle Time is tested functionally. SHUTDOWN AND SLEEP MODE CHARACTERISTICS (Pre and Post-Radiation)* (VDD= 2.3V to VDDQ, VDDQ = 2.3 to 3.6V; Unless otherwise noted TC is for temperature range ordered.) PARAMETER DESCRIPTION CONDITION MIN MAX UNIT tZZS3 Device operation to SLEEP mode ΖΖ > VIH 1 tCYC ns tZZH3 SLEEP high pulse width ΖΖ > VIH 100 μs tZZL3 SLEEP low pulse width ΖΖ < VIH 100 μs Device operation to SHUTDOWN SHUTDOWN > VIH 2 tCYC ns SLEEP recovery time STANDBY < VIL 100 + (3*tCYC) ns SHUTDOWN recovery time SHUTDOWN < VIL Active to SLEEP current ΖΖ > VIH Active to SHUTDOWN current SHUTDOWN > VIH tRZZI4 Time to exit SLEEP current mode STANDBY < VIL 0 ns tRSHTDWNI4 Time to exit SHUDOWN current mode SHUTDOWN < VIL 0 ns tCR1,2,3 Clock recovery prior to exiting ZZ ΖΖ > VIH tRLRH RESET low to high time Shutdown < VIL tPDS3 tPDH3 tSHTDWNS3 tZZREC3 tSHTDWNREC1,3 tZZI4 tSHTDWNI4 50 us 100 + (3*tCYC) ns 250 ns 20 μs 1 μs SLEEP setup time prior to CLK 2.0 ns SLEEP hold time after CLK 0.5 ns Notes: * For devices procured with a total ionizing dose tolerance guarantee, the post-irradiation performance is guaranteed at 25oC per MIL-STD-883 Method 1019, Condition A up to the maximum TID level procured 1. The clock must start up prior to exiting sleep or shutdown modes. Parameter is guaranteed by design. 2. TCR is necessary anytime the clock is stopped, after initial power on, or exiting shutdown mode. 3. Tested functionally. 4. Guaranteed by design. 36-00-01-005 Ver. 1.0.0 13 Aeroflex Microelectronics Solutions - HiRel tCYC tCL CLK Command Bus tCH 64th non- idle cycle 65th non- idle cycle non- idle cycle non- idle cycle non- idle cycle non- idle cycle non- idle cycle non- idle cycle Idle cycle Any cycle Any cycle tCQV 16 cycles MAX READY Any cycle tCQV Figure 3. Switching Waveform for Internal Housekeeping tCR CLK tZZH tRZZI tZZS ZZ tZZL tZZI tPDH tPDS Command Bus tZZREC RD/ WR RD/ WR Deselect cycle RD/ WR Figure 4. Switching Waveform for SLEEP Mode CLK tRSHTDWNI tSHTDWNS tSHTDWNREC SHUTDOWN Command Bus tCR tSHTDWNI RD/ WR RD/ WR Deselect cycle tRLRH RESET Figure 5. Switching Waveform for SHUTDOWN Mode CLK Power-up tSHTDWNREC SHUTDOWN Command Bus Deselect cycle tCR RD/ WR RD/ WR tRLRH RESET READY Figure 6. Switching Waveform for Power-Up 36-00-01-005 Ver. 1.0.0 14 Aeroflex Microelectronics Solutions - HiRel 36-00-01-005 Ver. 1.0.0 15 Aeroflex Microelectronics Solutions - HiRel W&+ $ W$+ 5($' 4$ W$6 :5,7( '$ W&4= 4$ W$'9/'+ 5($' 4$ '$ W'+ $ W'6 W$'9/'6 %8567 67$// :5,7( &<&/( '$ W2(4; W2(49 $ W%:(6 W%:(+ W:(6 W:(+ W&66 W&6+ W&<& W&(16 W&(1+ W&/ 5($' 4$ '$ $ 67$// &<&/( 67$// &<&/( 4$ 4$ W&4; W&49 :5,7( '$ W2(4= $ 5($' 4$ 4$ Figure 7. Switching Waveforms for Pipelined Cycle Operations W&42+ $ &6KDVWLPLQJWUDQVLWLRQVLGHQWLFDOWR&6DQG&6EXWLVLQYHUWHGORJLFDOO\)RUH[DPSOHZKHQ&6DQG&6DUH/2:&6LV+,*+ 1RWHV &+,3/(9(/ 67$// &200$1' &<&/( 4287 2( ',1 $''5 %:(>@ :( $'9B/' &6&6 &(1 &/. 4$ '( :5,7( 6(/(&7 '$ &<&/( '$ $ VDD VDD RTERM 100ohm CL = 40pF DUT Test Point Zo = 50ohm RTERM 100ohm VDD2 VSS 90% 90% 10% > 2.25V/ns 10% CMOS Input Pulses > 2.25V/ns Notes: 1. Measurement of data output occurs at the low to high or high to low transition mid-point (i.e., CMOS input = VDD2/2 Figure 8. AC Test Loads and Input Waveforms 36-00-01-005 Ver. 1.0.0 16 Aeroflex Microelectronics Solutions - HiRel PACKAGING Figure 9. 288-Lead CCGA 36-00-01-005 Ver. 1.0.0 17 Aeroflex Microelectronics Solutions - HiRel PACKAGING Figure 10. 288-Lead CLGA 36-00-01-005 Ver. 1.0.0 18 Aeroflex Microelectronics Solutions - HiRel PACKAGING Figure 11. Advanced 288-lead CBGA, Ball dimensions (A, A1, A2) are subject to change 36-00-01-005 Ver. 1.0.0 19 Aeroflex Microelectronics Solutions - HiRel ORDERING INFORMATION 2M x 40 SSRAM UT ******* - * * * * Lead Finish: (Note 1) (C) = Gold (A) = Solder Screening: (Notes 2, 3) (F) = HiRel Flow (Temperature Range: -55°C to +105°C) (In development, contact factory) (P) = Prototype Flow (Temperature Range: 25oC only) Package Type: (Z) = 288-Lead Ceramic Land Grid Array (CLGA) (S) = 288-Lead Ceramic Column Grid Array (CCGA) (C) = 288-Lead Ceramic Ball Grid Array (CBGA) Access Time: (M) = 80MHz Maximum Frequency Device Type: (8SF2M40) = 2Mbit x 40 SSRAM Device Notes: 1. Lead finish is per the table below. 2. Prototype Flow per Aeroflex Manufacturing Flows Document. Devices are tested at 25oC only. Radiation is neither tested nor guaranteed. 3. HiRel flow per Aeroflex Manufacturing Flows Document. Radiation is neither tested nor guaranteed. 36-00-01-005 Ver. 1.0.0 Package Option Associated Lead Finish Option (Z) 288-CLGA (C) Gold (S) 288-CCGA (A) Hot Solder Dipped (C) 288-CBGA (A) Hot Solder Dipped 20 Aeroflex Microelectronics Solutions - HiRel 2M x 40 SSRAM: SMD 5962 * ***** ** * * * Lead Finish: (Note 1) (C) = Gold (F) = Solder Case Outline: (X) = 288-Lead Ceramic Land Grid Array (CLGA) (F) = 288-Lead Ceramic Column Grid Array (CCGA) Class Designator: (Q) = QML Class Q (In development, contact factory) Device Type: (Note 2) (01) = fmax = 80MHz, QML Q only (Temperature Range: -55°C to +105°C) (02) = fmax = 80MHz Aeroflex Q+ Flow (Temperature Range -55°C to +105°C) Drawing Number: (TBD) = 2M x 40 SSRAM Total Dose: (R) = 100 krad(Si) Federal Stock Class Designator: No options Notes: 1. Lead finish is per the table below. 2. Aeroflex’s Q+ assembly flow, as defined in section 4.2.2.d of the SMD, provides QML-Q product through the SMD that is manufactured with Aeroflex’s QML-V flow. 36-00-01-005 Ver. 1.0.0 Package Option Associated Lead Finish Option (X) 288-CLGA (C) Gold (F) 288-CCGA (F) Hot Solder Dipped 21 Aeroflex Microelectronics Solutions - HiRel Aeroflex Colorado Springs - Datasheet Definition Advanced Datasheet - Product In Development Preliminary Datasheet - Shipping Prototype Datasheet - Shipping QML & Reduced Hi-Rel This product is controlled for export under the U.S. Department of Commerce (DoC). A license may be required prior to the export of this product from the United States. www.aeroflex.com/HiRel [email protected] Aeroflex Colorado Springs, Inc., reserves the right to make changes to any products and services described herein at any time without notice. Consult Aeroflex or an authorized sales representative to verify that the information in this data sheet is current before using this product. Aeroflex does not assume any responsibility or liability arising out of the application or use of any product or service described herein, except as expressly agreed to in writing by Aeroflex; nor does the purchase, lease, or use of a product or service from Aeroflex convey a license under any patent rights, copyrights, trademark rights, or any other of the intellectual rights of Aeroflex or of third parties. Our passion for performance is defined by three attributes represented by these three icons: solution-minded, performance-driven and customer-focused 22 Description of Change History Revision Date Description of Change April 2015 Version 1.0.0 Release of Preliminary Data Sheet 36-00-01-005 Ver. 1.0.0 23 Aeroflex Microelectronics Solutions - HiRel