SAW Components SAW RF low loss filter Satellite CSS Series/type: Ordering code: B1649 B39162B1649B510 Date: Version: December 10, 2012 2.0 EPCOS AG 2015. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. EPCOS AG is a TDK Group Company. SAW Components B1649 1680.0 MHz SAW RF low loss filter Data sheet Revision History: Changes compared to previous iteration issue ISSUE ORIGINATOR DETAIL SPEC CHANGES DATE DGLW68S01 0.1 HuA Initial release 01.03.2010 HuA First sample run release 12.03.2010 QuekJ Improvement of CMDR 15.09.2010 1.0 QuekJ Improvement of stop band attenuation 28.02.2011 1.1 HuA Revision history page included 17.10.2011 HuA Mass Prodcution Release 28.11.2012 LW68A 1.0 LW68B 1.0 LW68C B1649 2.0 Please read cautions and warnings and important notes at the end of this document. 2 December 10, 2012 SAW Components B1649 1680.0 MHz SAW RF low loss filter Data sheet Application ■ Low loss RF filter for satellite CSS ■ Usable passband 60.0 MHz ■ Balanced to balanced operation Features 0.6 1 1.5 1.5 3 7 5 side view top view 3.0 Pin configuration ■ ■ ■ ■ ■ ■ 1 2 5 6 3,7 4,8 Input Input Output Output To be grounded Case ground, to be grounded Please read cautions and warnings and important notes at the end of this document. 3 bottom view 1.8 1.1 Package size 3.0 x 3.0 x 1.1 mm3 Maximum height of 1.225 mm Package code QCC8F RoHS compatible Approximate weight 0.037 g Package for Surface Mount Technology (SMT) Ni, gold-plated terminals Electrostatic Sensitive Device (ESD) 3.0 ■ ■ ■ ■ ■ ■ ■ ■ December 10, 2012 SAW Components B1649 1680.0 MHz SAW RF low loss filter Data sheet Characteristics Temperature range for specification: Terminating source impedance: Terminating load impedance: T = ZS = ZL = –40 ˚C to +85 ˚C 150 Ω (balanced) and matching network 150 Ω (balanced) and matching network min. Nominal frequency fN Maximum insertion attenuation 1650.0 ... 1710.0 — max. — MHz αmax MHz Pass bandwidth αrel < 1.5 dB B1.5 dB Amplitude ripple (p-p) 1650.0 ... 1710.0 typ. @ 25 ˚C 1680.0 — 3.7 5.5 — 73.0 — 1.0 2.5 dB — dB MHz ∆α MHz Input return loss 7.4 12.5 — dB Output return loss 7.4 10.0 — dB MHz — 20.0 40.0 ns MHz 20.0 28.0 — dB 4.0 6.0 ˚ 48 42 52 35 — — — — dB dB dB dB Group delay ripple (p-p) 1650.0 ... 1710.0 ∆τ CMDR 1650.0 ... 1710.0 Deviation from linear phase (rms) in any 30 MHz band 1650.0 ... 1710.0 MHz — α Attenuation 50.0 1800.0 3000.0 4000.0 ... ... ... ... 1580.0 3000.0 4000.0 6000.0 MHz MHz MHz MHz Please read cautions and warnings and important notes at the end of this document. 40 38 35 30 4 December 10, 2012 SAW Components B1649 1680.0 MHz SAW RF low loss filter Data sheet Matching network (element values depend on PCB layout) Lp1 Lp1 = 15 nH Lp2 = 13 nH Lp2 Maximum ratings Operable temperature range T Storage temperature range Tstg DC voltage ESD voltage VDC VESD –40/+85 –40/+85 ˚C ˚C 0 501) V V machine model, 1 pulse dBm source impedance 150 Ω Input power at 1650.0... 1710.0 MHz 1) PIN 0 acc. to JESD22-A115A (machine model), 1 negative & 1 positive pulse. Transfer function Sdd21 Please read cautions and warnings and important notes at the end of this document. 5 December 10, 2012 SAW Components B1649 1680.0 MHz SAW RF low loss filter Data sheet Transfer function Sdd21 (passband) Transfer function Sdd21 (wideband) Please read cautions and warnings and important notes at the end of this document. 6 December 10, 2012 SAW Components B1649 1680.0 MHz SAW RF low loss filter Data sheet References Type B1649 Ordering code B39162B1649B510 Marking and package C61157-A7-A72 Packaging F61074-V8168-Z000 Date codes L_1126 S-parameters B1649_NB.s4p; B1649_WB.s4p Soldering profile S_6001 RoHS compatible defined as compatible with the following documents: "DIRECTIVE 2002/95/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 27 January 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment. 2005/618/EC from April 18th, 2005, amending Directive 2002/95/EC of the European Parliament and of the Council for the purposes of establishing the maximum concentration values for certain hazardous substances in electrical and electronic equipment." Moldability Before using in overmolding environment, please contact your EPCOS sales office. Matching coils See Inductor pdf-catalog http://www.tdk.co.jp/tefe02/coil.htm#aname1 and Data Library for circuit simulation http://www.tdk.co.jp/etvcl/index.htm For further information please contact your local EPCOS sales office or visit our webpage at www.epcos.com . Published by EPCOS AG Systems, Acoustics, Waves Business Group P.O. Box 80 17 09, 81617 Munich, GERMANY EPCOS AG 2011. This brochure replaces the previous edition. For questions on technology, prices and delivery please contact the Sales Offices of EPCOS AG or the international Representatives. Due to technical requirements components may contain dangerous substances. For information on the type in question please also contact one of our Sales Offices. Please read cautions and warnings and important notes at the end of this document. 7 December 10, 2012 Important notes The following applies to all products named in this publication: 1. 2. 3. 4. 5. 6. 7. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. The warnings, cautions and product-specific notes must be observed. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. The aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms of Delivery for Products and Services in the Electrical Industry” published by the German Electrical and Electronics Industry Association (ZVEI). The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CeraLink, CSMP, CSSP, CTVS, DeltaCap, DigiSiMic, DSSP, FilterCap, FormFit, MiniBlue, MiniCell, MKD, MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks. 8 December 10, 2012