ROHM LMR932F-TR

Datasheet
Operational Amplifiers Series
Input/Output Full Swing
Low Power Operational Amplifiers
LMR981G, LMR982FVM, LMR931G, LMR932F, LMR934F
●Key Specifications
 Low Operating Supply Voltage (single supply):
+1.8V to +5.0V
 High voltage gain (RL=600Ω):
101dB(Typ.)
 Wide Temperature Range:
-40°C to +85°C
 Turn on time from shutdown:
19μs (Typ.)
 Low Input Offset Voltage:
LMR981(Single)
4mV(Max.)
LMR931(Single)
4mV(Max.)
LMR982(Dual)
5.5mV(Max.)
LMR932(Dual)
5.5mV(Max.)
LMR934(Quad)
5.5mV(Max.)
 Low Input Bias Current:
10nA (Typ.)
●General Description
Input/Output Full Swing Low Voltage single, dual and
quad Op-Amp integrates into a single chip. Especially,
these series are operable with low voltage and low
supply current. Shutdown function are applied to
LMR981 and LMR982.
●Features
 Low operating supply voltage
 Input/Output Full Swing
 High large signal voltage gain
 Low input bias current
 Low supply current
 Low input offset voltage
●Package
SSOP5
SSOP6
MSOP10
SOP8
SOP14
●Applications
 Portable equipment
 Low voltage application
 Active filter
 Supply-Current Monitoring
 Battery Monitoring
W(Typ.) xD(Typ.) xH(Max.)
2.90mm x 2.80mm x 1.25mm
2.90mm x 2.80mm x 1.25mm
2.90mm x 4.00mm x 0.90mm
5.00mm x 6.20mm x 1.71mm
8.70mm x 6.20mm x 1.71mm
●Simplified Schematic
VDD
+IN
-IN
Class AB
Control
SHDN
(LMR981,LMR982)
OUT
VSS
Figure 1. Simplified Schematic (1 channel only)
○Product structure:Silicon monolithic integrated circuit
www.rohm.com
©2013 ROHM Co., Ltd. All rights reserved.
TSZ22111・14・001
○This product is not designed protection against radioactive rays.
1/45
TSZ02201-0RAR1G200570-1-2
25.JAN.2013 Rev.002
Datasheet
LMR981G, LMR931G, LMR982FVM, LMR932F, LMR934F
●Pin Configuration
LMR931G : SSOP5
+IN
1
Symbol
1
+IN
2
VSS
5 VDD
+
-
VSS 2
-IN
Pin No.
3
3
-IN
4
OUT
5
VDD
Pin No.
Symbol
6 VDD
1
+IN
2
VSS
5 SHDN
3
-IN
4
OUT
4 OUT
LMR981G : SSOP6
+IN
1
+
-
VSS 2
3
-IN
5
——————
6
SHDN
VDD
Pin No.
Symbol
1
OUT1
4 OUT
LMR932F : SOP8
8 VDD
OUT1 1
-IN1
2
+IN1
3
CH1
2
-IN1
3
+IN1
4
VSS
5
+IN2
6
-IN2
7
OUT2
8
VDD
Pin No.
Symbol
1
OUT1
7 OUT2
- +
6 -IN2
CH2
+ -
VSS
4
5 +IN2
LMR934F : SOP14
OUT1
OUT1 1
-IN1 2
-IN1
2
-IN1
3
+IN1
13 -IN4
-IN4
4
VDD
12 +IN4
+IN4
5
+IN2
6
-IN2
7
OUT2
8
OUT3
9
-IN3
10
+IN3
11
VSS
12
+IN4
14 OUT4
OUT4
CH1
- +
CH4
+ -
+IN1
+IN1 3
VCC 4
VDD
11 VSS
VEE
+IN2
+IN2 5
10 +IN3
+IN3
-IN2 6
-IN2
- +
CH2
+ CH3
OUT2
OUT2 7
www.rohm.com
©2013 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
9 -IN3
-IN3
8 OUT3
OUT3
2/45
13
-IN4
14
OUT4
TSZ02201-0RAR1G200570-1-2
25.JAN.2013 Rev.002
Datasheet
LMR981G, LMR931G, LMR982FVM, LMR932F, LMR934F
LMR982FVM : MSOP10
Pin No.
Symbol
1
OUT1
2
-IN1
3
+IN1
4
5
6
7
VSS
—————————
SHDN_1
—————————
SHDN_2
+IN2
8
-IN2
9
OUT2
10
VDD
Package
LMR931G
LMR981G
LMR982FVM
LMR932F
LMR934F
SSOP5
SSOP6
MSOP10
SOP8
SOP14
www.rohm.com
©2013 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
3/45
TSZ02201-0RAR1G200570-1-2
25.JAN.2013 Rev.002
Datasheet
LMR981G, LMR931G, LMR982FVM, LMR932F, LMR934F
●Shutdown(LMR981G , LMR982FVM)
Pin
Input condition
Shutdown function
VSS
ON
VDD
OFF
——————
SHDN
Note: Please refer to Electrical Characteristics regarding the turn on and off voltage.
●Ordering Information
L
M
R
9
x
x
x
x
x
-
Packaging and forming specification
TR: Embossed tape and reel
(SSOP5, SSOP6,MSOP10)
E2: Embossed tape and reel
(SOP8, SOP14)
Package
G:SSOP5
G:SSOP6
F:SOP8
FVM:MSOP10
F:SOP14
Part Number
LMR931G
LMR981G
LMR932F
LMR982FVM
LMR934F
xx
●Line-up
Topr
Package
-40°C to +85°C
Operable Part Number
SSOP5
Reel of 3000
LMR931G-TR
SSOP6
Reel of 3000
LMR981G-TR
MSOP10
Reel of 3000
LMR982FVM-TR
SOP8
Reel of 2500
LMR932F-E2
SOP14
Reel of 2500
LMR934F-E2
●Absolute Maximum Ratings(Ta=25°C)
Parameter
Ratings
Symbol
Supply Voltage
LMR981G
LMR931G
SSOP5
-
675*1*5
SSOP6
675*1*5
-
LMR932F
LMR982FVM
-
-
-
-
-
-
-
-
690*2*5
-
-
VDD-VSS
Power dissipation
Pd
*6
SOP8
Unit
LMR934F
+7
V
MSOP10
-
-
-
-
SOP14
-
-
-
562*3*5
mW
*4*5
587
-
Differential Input Voltage
Input Common-mode
Voltage Range
Operable with low voltage
Vid
VDD to VSS
V
Vicm
(VSS - 0.3) to (VDD + 0.3)
V
Vopr
+1.8 to +5.0
V
Operating Temperature
Topr
- 40 to +85
°C
Storage Temperature
Maximum
Junction Temperature
Tstg
- 55 to +150
°C
Tjmax
+150
°C
Note: Absolute maximum rating item indicates the condition which must not be exceeded.
Application of voltage in excess of absolute maximum rating or use out absolute maximum rated
temperature environment may cause deterioration of characteristics.
*1
To use at temperature above Ta=25°C reduce 5.4mW/°C.
*2
To use at temperature above Ta=25℃ reduce 5.52mW/℃.
*3
To use at temperature above Ta=25℃ reduce 4.5mW/℃.
*4
To use at temperature above Ta=25℃ reduce 4.7mW/℃.
*5
Mounted on a FR4 glass epoxy PCB(70mm×70mm×1.6mm).
*6
The voltage difference between inverting input and non-inverting input is the differential input voltage.
Then input terminal voltage is set to more than VSS.
www.rohm.com
©2013 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
4/45
TSZ02201-0RAR1G200570-1-2
25.JAN.2013 Rev.002
Datasheet
Notice
●General Precaution
1) Before you use our Products, you are requested to carefully read this document and fully understand its contents.
ROHM shall not be in any way responsible or liable for failure, malfunction or accident arising from the use of any
ROHM’s Products against warning, caution or note contained in this document.
2) All information contained in this document is current as of the issuing date and subject to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the latest information with a ROHM sales
representative.
●Precaution on using ROHM Products
1) Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment,
OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you
intend to use our Products in devices requiring extremely high reliability (such as medical equipment, transport
equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car
accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or
serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance.
Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any
damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific
Applications.
2)
ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3)
Our Products are designed and manufactured for use under standard conditions and not under any special or
extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any
special or extraordinary environments or conditions. If you intend to use our Products under any special or
extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of
product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4)
The Products are not subject to radiation-proof design.
5)
Please verify and confirm characteristics of the final or mounted products in using the Products.
6)
In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse) is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7)
De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual
ambient temperature.
8)
Confirm that operation temperature is within the specified range described in the product specification.
9)
ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Notice - Rev.004
© 2013 ROHM Co., Ltd. All rights reserved.
Datasheet
●Precaution for Mounting / Circuit board design
1) When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2)
In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the
ROHM representative in advance.
For details, please refer to ROHM Mounting specification
●Precautions Regarding Application Examples and External Circuits
1) If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2)
You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.
●Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
●Precaution for Storage / Transportation
1) Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2)
Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.
3)
Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.
4)
Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.
●Precaution for Product Label
QR code printed on ROHM Products label is for ROHM’s internal use only.
●Precaution for Disposition
When disposing Products please dispose them properly using an authorized industry waste company.
●Precaution for Foreign Exchange and Foreign Trade act
Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act,
please consult with ROHM representative in case of export.
●Precaution Regarding Intellectual Property Rights
1) All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable
for infringement of any intellectual property rights or other damages arising from use of such information or data.:
2)
No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the information contained in this document.
Notice - Rev.004
© 2013 ROHM Co., Ltd. All rights reserved.
Datasheet
●Other Precaution
1) The information contained in this document is provided on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate and/or error-free. ROHM shall not be in any way responsible or
liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or
concerning such information.
2)
This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
3)
The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
4)
In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
5)
The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
Notice - Rev.004
© 2013 ROHM Co., Ltd. All rights reserved.