BeRex Preliminary BT011 1500-4000 MHz Wideband Drive Amplifier Device Features • 45dBm Output IP3 at 1900MHz 12dBm/tone • 14.5 dB Gain at 1900MHz • 25.5 dBm P1dB at 1900 MHz • Highly Reliable InGaP/GaAs HBT Technology • Patent pending over voltage protection circuit • Lead-free/Green/RoHS compliant SOT89 package Target Device Performance (Ta = 25°C) Symbols Parameters Test Conditions Gain S11 S22 OIP3 P1dB IS-95 CH Power @-45dBc ACPR NF Ic Vc Rth 1900MHz 2100MHz 2350MHz 1900MHz 2100MHz 2350MHz 1900MHz 2100MHz 2350MHz 1900MHz 2100MHz 2350MHz 1900MHz 2100MHz 2350MHz Min Typ 13.5 12.5 11.5 14.5 13.5 12.5 -17.8 -19.3 -16.7 -17.1 -11.8 -14.8 45.0 43.0 40.0 25.5 25.5 25.5 43.0 41.0 38.0 24.5 24.5 24.5 1900MHz 19.0 1900MHz 2100MHz 2350MHz Vdevice = 4.6V 4.5 4.4 5.0 70 5 50 60 Thermal Resistance Max Unit dB dB dB dBm dBm dBm dB 80 mA V °C/W Test conditions unless otherwise noted. 1. T = 25°C, Vc = 5V, 50 ohm system. 2. OIP3 is measured on an eval-board with two tones separated by 1 MHz. Absolute Maximum Ratings Parameter Rating Operating Case temperature Storage Temperature Junction Temperature Supply Voltage Max. Device Current Input RF Power -40 to +85°C -40 to +155°C +220°C 6.0V 160mA 6dB above input P1dB Operation of this device above any of these parameters may result in permanent damage. Rev B71016 MMIC Innovator http: //www.berex.com BeRex Preliminary BT011 Typical Device Data S-parameters (Vdevice =4.6V, Ic=70mA, T=25°C) Generic SOT89 Evaluation Board I-V Characteristics BeRex Evaluation Board RF Input RF Output MMIC Innovator Dielectric constant is 4.2 RF pattern width 52mil 31mil thick FR4 PCB Rev B71016 MMIC Innovator http: //www.berex.com BeRex Preliminary BT011 S-Parameter (4.6V/70mA) Freq [MHz] S11 [Mag] S11 [Ang] S21 [Mag] S21 [Ang] S12 [Mag] S12 [Ang] S22 [Mag] S22 [Ang] 100 500 1000 1500 2000 2500 3000 3500 4000 0.993 0.867 0.900 0.861 0.854 0.889 0.920 0.911 0.860 -26.867 -108.527 -145.551 177.744 150.256 130.065 116.271 105.893 94.389 1.443 2.771 4.068 3.673 3.003 2.514 2.069 1.712 1.581 -128.742 178.518 163.830 128.257 105.833 90.149 77.799 65.108 55.613 0.007 0.021 0.031 0.041 0.044 0.045 0.052 0.050 0.063 79.175 22.575 74.517 49.347 42.967 39.255 40.745 37.906 36.576 0.475 0.608 0.458 0.369 0.406 0.468 0.526 0.554 0.534 -162.036 175.974 134.377 130.716 121.984 112.473 104.553 98.767 92.749 Application Circuit: 1900 MHz Schematic Diagram BOM Tolerance C1 100pF ± 5% C2 1000pF ± 5% C3 10uF ± 20% C4 C5 100pF 100pF ± 5% ± 5% C6 3.3pF ± 5% C7 0.5pF ± 5% *R1 5.6ohm ± 5% L1 33nH ±5% *Use recommended R1 for the best OIP3 performance. R1 changes OIP3 performance. Typical Performance Rev B71016 MMIC Innovator http: //www.berex.com BeRex Preliminary BT011 Application Circuit: 2100 MHz Schematic Diagram BOM C1 C2 C3 C4 C5 C6 C7 *R1 L1 100pF 1000pF 10uF 100pF 100pF 2.7pF 0.5pF 4.7ohm 12nH Tolerance ±5% ±5% ±20% ±5% ±5% ±5% ±5% ±5% ±5% *Use recommended R1 for the best OIP3 performance. R1 changes OIP3 performance. Rev B71016 MMIC Innovator http: //www.berex.com BeRex Preliminary BT011 Typical Performance Rev B71016 MMIC Innovator http: //www.berex.com BeRex Preliminary BT011 Application Circuit: 2350MHz Schematic Diagram BOM Tolerance C1 100pF C2 1000pF C3 10uF C4 100pF C5 100pF C6 2pF C7 0.5pF *R1 5.6ohm L1 6.8nH ±5% ±5% ±20% ±5% ±20% ±5% ±5% ± 5% ±5% *Use recommended R1 for the best OIP3 performance. R1 changes OIP3 performance. Typical Performance Rev B71016 MMIC Innovator http: //www.berex.com BeRex Preliminary BT011 Tape & Reel SOT89 Packaging information Tape Width (mm): 12 Reel Size (inches): 7 Device Cavity Pitch (mm): 8 Devices Per Reel: 1000 MSL / ESD Rating ESD Rating Value Test Standard Class 1C Passes < 2000V Human Body Model (HBM) JEDEC Standard JESD22-A114B MSL Rating Standard Level 3 at +265°C convection reflow JEDEC Standard J-STD-020 NOTICE BeRex Corporation reserves the right to make changes of product specification or to discontinue product at any time without notice. Rev B71016 MMIC Innovator http: //www.berex.com