Capacitor Hardware Type VR Vertical Mounting Clamp Catalog Part Number Diameter Unassembled Assembled of Part to be Without Screw & Nut with Mounted Screw & Nut Included Screw & Nut 1" to 1-1/16 B C VR1B VR1 VR1A 1" 1-7/16" 1-7/8*" VR3B VR3 VR3A 1-3/8" 1-25/32" 2-7/32" 1-1/2" to 1-9/16 VR4B VR4 VR4A 1-1/2" 1-15/16" 2-11/32" 1-3/4" to 1-13/16 VR6B VR6 VR6A 1-3/4" 2-1/4" 2-9/16" 2" to 2-1/16 VR8B VR8 VR8A 2" 2-1/2" 2-13/16" 2-1/2" to 2-9/16 VR10B VR10 VR10A 2-1/2" 3" 3-5/16" 3" to 3-1/8 VR12B VR12 VR12A 3" 3-7/16" 3-13/16" VRSCREW — — 9/16" long 6-32 thread NC-2A VRNUT — — Standard hex nut to fit screws Nut VR6, 8,10 & 12 VR1, 3 & 4 .219” 0.176” x 0.281” ±0.016 (3 places). .375” 120 º ±3 º (3 Places) 2 Holes .1561” Dia. B Mtng ±0.03” .562” .750” Mounted TH17 TH25 0.625 1.375 Ø 0.201” ±0.005” 0.375”±0.016” 0.035” Nominal Dia. Part Number 75 º A ±0.016” 1.125” ±0.016” Dimensions in Inches of Part to be 0.34 4 0.18 ” ±0.01 6 8” ± 0.01 ” 6” .156” B Mtg Catalog B Mtng ±0.03” C ±0.01” Type TH Horizontal Mounting Clip 0.075” ±0.016” 0.500” ±0.016” A C B 0.312 0.720 0.312 1.500 Added tolerance to "C" dim. Material Thickness TH17 is 0.016”, TH25 is 0.025”. Material: 1050 high carbon steel with phosphate and oil finish. TH25 is 1060. A 1-3/8" to 1-7/16 Screw CDE VR mounting clamps may be used to mount any cylindrical capacitor with a 1” to 3” diameter that is to be mounted in a vertical position. Material is 1010 CRS, commercial grade #4 temper ASI scale. Parts are finished with .0001 (nominal) zinc chromate plating. Use for mounting CG types, PSU, SF and MPF types. Material thickness is .035” Dimensions 0.015 0.030 (*) 0.340” execpt TH25 is 0.590” (*) Retaining tabs Retaining tabs must must extend lower extend base of clip lowerthan than base of clip (*) 0.340" except TH25 is 0.590". B These clips, though designed for capacitors, have varied applications to retain many cylindrical components. They are used extensively in the electrical and electronic industries to hold spindles, condensers, capacitors, tubes, rods and conduit. Clips have phosphate and oil finish. C ±0.010" A 0.594" 0.135" 0.135”Dia. Dia.Hole Hole ACR15KT Motor Start Resistor Kit ACR220KT Motor Run Resistor Kit 15K Ohm 2 watt bleeder resistors for AC motor start applications. Saves relay switch contacts and capacitor, particularly in capacitor start applications. 1/4” quick connect terminals eliminate need for soldering. 220K Ohm 1 watt bleeder resistors for AC motor run applications. Saves relay switch contacts and capacitor, particularly in capacitor run applications. 1/4” quick connect terminals eliminate need for soldering. ACR15K: Pack of 10, 15K Ohm 2 watt bleeder resistor without quick connect terminals. ACR220K: Pack of 10, 220K Ohm 1 watt bleeder resistor without quick connect terminals. CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com Capacitor Hardware Oval Capacitor Hardware Wrap Around Bracket Mounting Brackets #32107 Case Code Bracket 32 A 32107-1 37 C 32107-2 38 D 32107-3 Case Code Bracket 32 A 30393-5 OB2 37 C 30393-9 OB4 38 D OB3 OB3 6-32 Screw and Nut Insulating Terminal Boots UL Approved Material 44603 or OC1 44603 32108-2 Motor Start Mounting Hardware End Cap Bracket 0.375" Round Capacitor Hardware 3 Footed Round Mounting Bracket Case Code Bracket 21 P VR6B 23 S VR8B 24 T VR10B Case Case Dimensions Down Up Optional Code (Inches) Wire Wire Mounting D L Cap Cap Bracket 1 1.438 2.750 PL3 PLA3 HB2 2 1.438 3.375 PL3 PLA3 HB4 3 1.438 4.375 PL3 PLA3 HB8 4 1.813 3.375 PL6 PLA6 HB4 5 1.813 4.375 PL6 PLA6 HB8 6 2.063 3.375 PL8 PLA8 HB4 7 2.063 4.375 PL8 PLA8 HB8 8 2.563 4.375 PL10 PLA10 HB8 Order both endcap and bracket for mounting Wrap Around Bracket Case Code Bracket 21 P RB175 23 S RB200 24 T RB250 CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com Capacitor Hardware Screw-Terminal, Computer-Grade Capacitor, Mounting Hardware Figure 1 Figure 3 Figure 2 Figure 4 Clamp Dimensions Clamp Dimensions in Inches Number A B C D 125562-01 1.375 2.125 2.500 1.281 125562-05 1.750 2.500 2.875 1.656 125562-02 2.000 2.750 3.125 1.906 125562-04 2.500 3.250 3.625 2.406 125562-03 3.000 3.750 4.125 2.906 125562-06 3.500 4.250 4.625 3.481 Bracket Dimensions Dimensions in Inches Figure Bracket Dimensions in Millimeters A B C D E F A B C D E F Number 1 125565-06* 1.375 1.813 30 º 2.313 .750 .563 34.93 46.04 30º 58.74 19.05 14.30 1 125565-15* 1.750 2.188 30 º 2.625 .750 .560 44.45 55.56 30º 66.68 19.05 14.22 2 125565-09* 2.000 1.250 75 º 1.438 1.125 .750 50.80 31.75 75º 36.51 28.58 19.05 3 125565-05 2.000 2.563 30 º 2.938 1.125 .750 50.80 65.09 30º 76.41 28.58 19.05 2 125565-14* 2.500 1.500 75 º 1.688 1.125 .750 63.50 38.10 75º 42.86 28.58 19.05 3 125565-10 2.500 3.000 30 º 3.438 1.125 .750 63.50 76.20 30º 87.31 28.58 19.05 2 125565-11* 3.000 1.750 75 º 1.938 1.125 .750 76.20 44.45 75º 49.21 28.58 19.05 3 125565-01 3.000 3.500 30 º 3.938 1.125 .750 76.20 88.90 30º 100.01 28.58 19.05 4 125309-01 3.500 4.488 60 º 2.224 .984 – 90.00 114.00 60º 4.70 25.00 – Note: All mounting brackets and clamps except Figure 4 are zinc plated. Figure 4 is a black nylon. When mounting capacitors there is no need to wrap capacitors with protective wrapping before installing mounting clamp. *Stock bracket Nylon Nuts for Insulated Stud Mounting Nylon Hex Nut Metal Plate/ Heat Sink (Reference only) For Stud Standoff Nylon Nut Part Number Nut Nut Diameter Diameter Diameter Elevation (mm) S (mm) W (mm) T (mm) Hex Mounting Head Min. Hole Max. Chassis Max. Tightening J (mm) Diameter Thickness Torque (mm) (mm) in. lbs. M8S17W25 M8 17 25 15 17 17.5 5 25 M12S22W30 M12 22 30 18 19 22.5 5 75 M12S30W38 M12 30 38 18 19 30.5 5 75 CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com Capacitor Hardware Notice and Disclaimer: All product drawings, descriptions, specifications, statements, information and data (collectively, the “Information”) in this datasheet or other publication are subject to change. The customer is responsible for checking, confirming and verifying the extent to which the Information contained in this datasheet or other publication is applicable to an order at the time the order is placed. All Information given herein is believed to be accurate and reliable, but it is presented without any guarantee, warranty, representation or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on the knowledge that the Cornell Dubilier company providing such statements (“Cornell Dubilier”) has of operating conditions that such Cornell Dubilier company regards as typical for such applications, but are not intended to constitute any guarantee, warranty or representation regarding any such matter – and Cornell Dubilier specifically and expressly disclaims any guarantee, warranty or representation concerning the suitability for a specific customer application, use, storage, transportation, or operating environment. The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by Cornell Dubilier with reference to the use of any Cornell Dubilier products is given gratis (unless otherwise specified by Cornell Dubilier), and Cornell Dubilier assumes no obligation or liability for the advice given or results obtained. Although Cornell Dubilier strives to apply the most stringent quality and safety standards regarding the design and manufacturing of its products, in light of the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies or other appropriate protective measures) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicated in such warnings, cautions and notes, or that other safety measures may not be required. CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com