Type 167/184 Metallized Polyester Radial Lead Capacitors

Type 167/184 Metallized Polyester Radial Lead Capacitors
Radial Box Metallized Polyester Capacitors for Automatic Insertion
The Type 167/184 series radial lead metallized polyester box capacitors are available in bulk (Type 167) or on
ammo pack or radial tape and reel (Type 184). These
capacitors are constructed in rugged rectangular plastic cases and all come with 7.5 mm (0.3”) lead spacing. They are good for general purpose applications such
as bypass, decoupling, energy storage/discharge and
arc suppression.
Highlights
•
•
•
•
•
•
Rugged plastic case
Case and epoxy fill meets UL94V0
7.5 mm (0.3”) lead spacing
Bulk, tape and reel or ammo pack
Non-inductively wound Non-polar
Specifications
RoHS Compliant
Capacitance Range:
Voltage Range:
Capacitance Tolerance:
Operating Temperature Range:
Dielectric Withstand Voltage:
Dissipation Factor (DF):
0.001 µF to 1.0 µF
63 Vdc to 630 Vdc
±5%, ±10%, ±20%
–55 ºC to +125 ºC (with 50% Vdc derating >85 ºC)
1.6 x rated voltage for 2 sec @ +25 ºC ±5 ºC
tanδ x 10–4 at 25 ºC ±5 ºC
kHz
tand x 10–4
1
≤100
10
≤150
Total Self Inductance (L): Approximately 8 nH
Maximum Pulse Rise Time (dv/dt):
Vn
V/µs
63
12
100
20
250
32
400
41
630
70
If the working voltage (V) is less than the nominal voltage (Vn),
the capacitor can work at higher dv/dt. In this case, the maximum
value allowed is obtained by multiplying the above value with
the ratio Vn/V.
Long Term Stability (after two years)
Storage
Standard Environmental Conditions
Performance
Capacitance Change ∆C/C
≤ ±3%
CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com
Type 167/184 Metallized Polyester Radial Lead Capacitors
Capacitor Outline Drawing
Test Method and Performance Insulation Resistance
T
L
Test Conditions
Temperature
Voltage Charge Time
Voltage Charge
Max
Max
H
Max
Performance
For Vn > 100 Vdc
For Vn ≤100 Vdc
.217 ±.039
(5.5 ±1.0 mm)
S
±.015
(±0.4 mm)
Lead length shown is as supplied on 167 Series
Soldering
260 ºC ±5 ºC
10 sec ±1 sec
Test Conditions
Temperature
Test Duration
Voltage Applied
Performance
Capacitance Change ∆C/C
DF Change ∆tgδ
Insulation Resistance
≤ ±2%
≤30 x 10–4 at 10 kHz
≥ limit value
Ratings
Cap
(µF)
≥30,000 MΩ (50,000 MΩ typical)
≥10,000 MΩ for C ≤ 0.1µF
≥1,000 MΩ x µF for > 0.1µF
Damp Heat Test
Test Conditions
Temperature
Relative Humidity
Test Duration
Performance
Capacitance Change ∆C/C
DF Change ∆tgδ
Insulation Resistance
Ød ±.003
(±0.076)
Test Conditions
Soldering Temperature
Soldering Duration
Performance
Capacitance Change ∆C/C
DF Change ∆tgδ
Insulation Resistance
25 ºC ±5 ºC
1 minute
50 Vdc for Vn < 100 Vdc
100 Vdc for Vn ≥ 100 Vdc
+40 ºC
95%
21 days
≤ ±5%
≤50 x 104 at 1 kHz
≥ 50% of limit value
Life Test
+85 ºC
1000 hrs
1.25 x Vn
≤ ±5%
≤30 x 10–4 at 10 kHz
≥ 50% of limit value
RoHS Compliant
Catalog
Part Number
Tape & Reel
Ammo Pack
Inches
L
T
H
Millimeters
S
Ød
L
T
H
S
Ød
63 Vdc
.068
167683*63A–F
184683*63#A>–F
0.413
0.138
0.276
0.295
0.024
10.5
3.5
7.0
7.5
0.6
.10
167104*63A–F
184104*63#A>–F
0.413
0.138
0.276
0.295
0.024
10.5
3.5
7.0
7.5
0.6
.15
167154*63A–F
184154*63#A>–F
0.413
0.138
0.276
0.295
0.024
10.5
3.5
7.0
7.5
0.6
.22
167224*63A–F
184224*63#A>–F
0.413
0.138
0.276
0.295
0.024
10.5
3.5
7.0
7.5
0.6
.27
167274*63A–F
184274*63#A>–F
0.413
0.138
0.276
0.295
0.024
10.5
3.5
7.0
7.5
0.6
.33
167334*63A–F
184334*63#A>–F
0.413
0.138
0.276
0.295
0.024
10.5
3.5
7.0
7.5
0.6
.47
167474*63B–F
184474*63#B>–F
0.413
0.157
0.354
0.295
0.024
10.5
4.0
9.0
7.5
0.6
.68
167684*63C–F
184684*63#C>–F
0.413
0.197
0.433
0.295
0.024
10.5
5.0
11.0
7.5
0.6
1.00
167105*63C–F
184105*63#C>–F
0.413
0.197
0.433
0.295
0.024
10.5
5.0
11.0
7.5
0.6
100 Vdc
.033
167333*100A–F
184333*100#A>–F
0.413
0.138
0.276
0.295
0.024
10.5
3.5
7.0
7.5
0.6
.047
167473*100A–F
184473*100#A>–F
0.413
0.138
0.276
0.295
0.024
10.5
3.5
7.0
7.5
0.6
.068
167683*100A–F
184683*100#A>–F
0.413
0.138
0.276
0.295
0.024
10.5
3.5
7.0
7.5
0.6
.10
167104*100A–F
184104*100#A>–F
0.413
0.138
0.276
0.295
0.024
10.5
3.5
7.0
7.5
0.6
.12
167124*100B–F
184124*100#B>–F
0.413
0.157
0.354
0.295
0.024
10.5
4.0
9.0
7.5
0.6
.15
167154*100B–F
184154*100#B>–F
0.413
0.157
0.354
0.295
0.024
10.5
4.0
9.0
7.5
0.6
.22
167224*100C–F
184224*100#C>–F
0.413
0.197
0.433
0.295
0.024
10.5
5.0
11.0
7.5
0.6
.33
167334*100C–F
184334*100#C>–F
0.413
0.197
0.433
0.295
0.024
10.5
5.0
11.0
7.5
0.6
* Indicates capacitance tolerance: J = ±5%, K = ±10%, M = ±20%
# Indicates packaging type: R = Tape and Reel, A = Ammo Pack
> Indicates tooling code: A = 16.5 mm, B = 18.5 mm, C = 16.0 mm (See H dimension in taping specifications)
CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com
Type 167/184 Metallized Polyester Radial Lead Capacitors
Cap
(µF)
Catalog
Part Number
Inches
Tape & Reel
Ammo Pack
L
T
H
Millimeters
S
Ød
L
T
H
S
Ød
250 Vdc
.010
167103*250A–F
184103*250#A>–F
0.413
0.138
0.276
0.295
0.024
10.5
3.5
7.0
7.5
0.6
.015
167153*250A–F
184153*250#A>–F
0.413
0.138
0.276
0.295
0.024
10.5
3.5
7.0
7.5
0.6
.018
167183*250A–F
184183*250#A>–F
0.413
0.138
0.276
0.295
0.024
10.5
3.5
7.0
7.5
0.6
.022
167223*250A–F
184223*250#A>–F
0.413
0.138
0.276
0.295
0.024
10.5
3.5
7.0
7.5
0.6
.027
167273*250B–F
184273*250#B>–F
0.413
0.157
0.354
0.295
0.024
10.5
4.0
9.0
7.5
0.6
.033
167333*250B–F
184333*250#B>–F
0.413
0.157
0.354
0.295
0.024
10.5
4.0
9.0
7.5
0.6
.039
167393*250B–F
184393*250#B>–F
0.413
0.157
0.354
0.295
0.024
10.5
4.0
9.0
7.5
0.6
.047
167473*250B–F
184473*250#B>–F
0.413
0.157
0.354
0.295
0.024
10.5
4.0
9.0
7.5
0.6
.068
167683*250C–F
184683*250#C>–F
0.413
0.197
0.433
0.295
0.024
10.5
5.0
11.0
7.5
0.6
.100
167104*250C–F
184104*250#C>–F
0.413
0.197
0.433
0.295
0.024
10.5
5.0
11.0
7.5
0.6
.0047
167472*400A–F
184472*400#A>–F
0.413
0.138
0.295
0.024
10.5
3.5
7.0
7.5
0.6
400 Vdc
0.276
.0056
167562*400A–F
184562*400#A>–F
0.413
0.138
0.276
0.295
0.024
10.5
3.5
7.0
7.5
0.6
.0068
167682*400A–F
184682*400#A>–F
0.413
0.138
0.276
0.295
0.024
10.5
3.5
7.0
7.5
0.6
.010
167103*400A–F
184103*400#A>–F
0.413
0.138
0.276
0.295
0.024
10.5
3.5
7.0
7.5
0.6
.015
167153*400B–F
184153*400#B>–F
0.413
0.157
0.354
0.295
0.024
10.5
4.0
9.0
7.5
0.6
.022
167223*400C–F
184223*400#C>–F
0.413
0.197
0.433
0.295
0.024
10.5
5.0
11.0
7.5
0.6
.033
167333*400C–F
184333*400#C>–F
0.413
0.197
0.433
0.295
0.024
10.5
5.0
11.0
7.5
0.6
0.295
0.024
10.5
3.5
7.0
7.5
0.6
630 Vdc
.0010
167102*630A–F
184102*630#A>–F
0.413
0.138
0.276
.0015
167152*630A–F
184152*630#A>–F
0.413
0.138
0.276
0.295
0.024
10.5
3.5
7.0
7.5
0.6
.0022
167222*630A–F
184222*630#A>–F
0.413
0.138
0.276
0.295
0.024
10.5
3.5
7.0
7.5
0.6
.0033
167332*630A–F
184332*630#A>–F
0.413
0.138
0.276
0.295
0.024
10.5
3.5
7.0
7.5
0.6
.0047
167472*630B–F
184472*630#B>–F
0.413
0.157
0.354
0.295
0.024
10.5
4.0
9.0
7.5
0.6
.0068
167682*630B–F
184682*630#B>–F
0.413
0.157
0.354
0.295
0.024
10.5
4.0
9.0
7.5
0.6
.010
167103*630C–F
184103*630#C>–F
0.413
0.197
0.433
0.295
0.024
10.5
5.0
11.0
7.5
0.6
.015
167153*630D–F
184153*630#D>–F
0.413
0.236
0.472
0.295
0.024
10.5
6.0
12.0
7.5
0.6
* Indicates capacitance tolerance: J = ±5%, K = ±10%, M = ±20%
# Indicates packaging type: R = Tape and Reel, A = Ammo Pack
> Indicates tooling code: A = 16.5 mm, B = 18.5 mm, C = 16.0 mm (See H dimension in taping specification)
Part Numbering System for Bulk Items
167
Series
167
104
Capacitance
K
Tolerance
A
-F
Case
RoHS
Voltage
Code
Compliant
63 = 63 Vdc
A
Designator
K = ±10%
100 = 100 Vdc
B
M = ±20%
250 = 250 Vdc
C
630 = 630 Vdc
D
392 = .0039 µF
J = ±5%
103 = .01 µF
104 = .1 µF
105 = 1.0 µF
100
CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com
Type 167/184 Metallized Polyester Radial Lead Capacitors
Tape Specification - 7.5 mm Lead Spacing
30 mm
1.18”
Reel
Packing
ΔH
P1
331 mm
13.04”
Ammo Box
Packing
P
Po
280 mm Max
11.02”
Wo
W
W1
H
W2
Ød
Do
47 mm Max
1.85”
Item
Code
Lead-Wire Diameter
Ød
Millimeters
0.6+0.04 –0.01
Inches
.024±.001
Lead-to-Lead Distance
P
7.5+0.6 –0.2
.295+.024 –.040
Feed Hole Pitch
P0
2.7±0.3
.5±.012
Pitch of Component
P1
12.7±1.0
.5±.039
Hole Center to Lead
P2
3.75±0.7
.148±.028
Component Alignment, F-R
∆h
0±2.0
0±.079
Tape Width
W
18+1.0 –0.1
.709+.039 –.004
Hold-down Tape Width
W0
6.0 min
.236 min
Hole Position
W1
9.0
.355+.030 –.001
Hold-down Tape Position
W2
3.0 Max
.118 Max
Height of Component
H
+0.75 –0.05
>
335 mm Max
13.19”
Case
Quantity
Quantity
Code
Reeled
Ammo Pack
A
1800
1500
B
1500
1500
C
1200
1000
D
1000
1000
> The H dimension depends on the
insertion equipment used. Specify
the proper tooling code as indicated
below.
Tooling
Millimeters
Inches
A
16.5±0.75
.679±.030
B
18.5±0.75
.728±.030
C
16.0
.630±030
>
from Tape Center
Feed Hole Diameter
D0
4.0±0.3
H Dimensions
Code
.157±.012
±0.75
Part Numbering System for Auto Insertion
184
104
K
100
R
A
Packaging
Series
Capacitance
184 392 = .0039 µF
Tolerance
J = ±5%
B
-F
*Tooling
RoHS
Type
Case
Code
Compliant
Voltage
(#)
Code
(>)
Designator
63 = 63 Vdc
A = Ammo
A
A
R = Tape & Reel
103 = .01 µF
K = ±10%
100 = 100 Vdc
B
B
104 = .1 µF
M = ±20%
250 = 250 Vdc
C
C
630 = 630 Vdc
D
105 = 1.0 µF
* Tooling code is at the discretion
of the user depending on the
insertion equipment being used.
See table for specific "H" dimensions
* Tooling code (>) depends on the users insertion equipment requirements. See table for available options.
CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com
Type 167/184 Metallized Polyester Radial Lead Capacitors
Notice and Disclaimer: All product drawings, descriptions, specifications, statements, information and
data (collectively, the “Information”) in this datasheet or other publication are subject to change. The
customer is responsible for checking, confirming and verifying the extent to which the Information contained in this datasheet or other publication is applicable to an order at the time the order is placed. All
Information given herein is believed to be accurate and reliable, but it is presented without any guarantee, warranty, representation or responsibility of any kind, expressed or implied. Statements of suitability
for certain applications are based on the knowledge that the Cornell Dubilier company providing such
statements (“Cornell Dubilier”) has of operating conditions that such Cornell Dubilier company regards
as typical for such applications, but are not intended to constitute any guarantee, warranty or representation regarding any such matter – and Cornell Dubilier specifically and expressly disclaims any guarantee,
warranty or representation concerning the suitability for a specific customer application, use, storage,
transportation, or operating environment. The Information is intended for use only by customers who
have the requisite experience and capability to determine the correct products for their application. Any
technical advice inferred from this Information or otherwise provided by Cornell Dubilier with reference
to the use of any Cornell Dubilier products is given gratis (unless otherwise specified by Cornell Dubilier),
and Cornell Dubilier assumes no obligation or liability for the advice given or results obtained. Although
Cornell Dubilier strives to apply the most stringent quality and safety standards regarding the design
and manufacturing of its products, in light of the current state of the art, isolated component failures may
still occur. Accordingly, customer applications which require a high degree of reliability or safety should
employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies or other appropriate protective measures) in order to ensure that the failure of an electrical component
does not result in a risk of personal injury or property damage. Although all product-related warnings,
cautions and notes must be observed, the customer should not assume that all safety measures are indicated in such warnings, cautions and notes, or that other safety measures may not be required.
CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com