Type 160 Metallized Polyester Radial Lead Capacitors Radial Box Metallized Polyester Capacitors The Type 160 series radial lead metallized polyester box capacitors are constructed in rugged rectangular plastic cases with lead spacings that are standard in the electronics industry. All Type 160 capacitors are available in bulk with a .217” ±.039” lead length, and they are good for general purpose applications such as bypass, decoupling, energy storage/discharge and arc suppression. Highlights • • • • • • • Specifications Capacitance Range: Voltage Range: Capacitance Tolerance: Operating Temperature Range: Dielectric Withstand Voltage: Dissipation Factor (DF): Total Self Inductance (L): Long Term Stability (after two years): Corona (Partial Discharge Inception Voltage): RoHS compliant Rugged plastic case Case and epoxy fill meets UL94V0 10 mm through 27.5 mm lead spacings Non-inductively wound Non-polar Wire lead material, tinned copper clad steel RoHS Compliant 0.0022 µF to 10.0 µF 63 Vdc to 1000 Vdc ±5%, ±10%, ±20% –55 ºC to +105 ºC (derating voltage to 1.25% per ºC above 85 ºC) 1.6 x rated voltage for 2 sec @ +25 ºC ±5 ºC tanδ x 10–4 at 25 ºC ±5 ºC kHz C ≤1 µF C >1 µF 1 ≤100 ≤100 10 ≥150 Pitch (mm) 10 15 22.5 27.5 L (nH) ≈ 9 10 18 18 Capacitance change ∆C/C ≤ ±3% under standard environmental conditions 200 Vac for 100 Vdc, 200 Vdc 250 Vac for 400 Vdc, 630 Vdc 300 Vac for 1000 Vdc Maximum Pulse Rise Time (dv/dt): Pitch (mm) Vn 10 15 22.5 63 3 1.5 1 27.5 1 100/160 6/8 3 2 1 3 250 11 7 4 400 20 10 5.5 5 630 30 15 8 7 1000 60 25 15 10 If the working voltage (V) is less than the nominal voltage (Vn), the capacitor can work at higher dv/dt. In this case, the maximum value allowed is obtained by multiplying the above value with the ratio Vn/V. CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com Type 160 Metallized Polyester Radial Lead Capacitors Test Method and Performance Capacitor Outline Drawing Insulation Resistance Test Conditions T L Max Max H Max 25 ºC ±5 ºC Voltage Charge Time 1 minute Voltage Charge 50 Vdc for Vn < 100 Vdc 100 Vdc for Vn ≥ 100 Vdc Performance ≥30,000 MΩ for ≤ 0.33µF For Vn > 100 Vdc .196 -.040 / +0.06 ≥10,000 MΩ x µF for C > 0.33µF (5.0 -1 / +1.5 mm) S ±0.016 (±0.5 mm) Temperature For Vn ≤100 Vdc ≥10,000 MΩ for C ≤ 0.1µF ≥1,000 MΩ x µF for ≤ 0.1µF Ød ±0.003 (±0.076 mm) Damp Heat Test Test Conditions Temperature Note: The lead diameter is a maximum dimension for lead spacing ≤15 mm and a nominal for lead spacing >15 mm +40 ºC Relative Humidity 95% Test Duration 21 days Performance Capacitance Change ∆C/C ≤ ±5% DF Change ∆tgδ ≤50 x 104 at 1 kHz ≥ 50% of limit value Insulation Resistance Life Test Soldering Test Conditions Test Conditions Soldering Temperature 260 ºC ±5 ºC Soldering Duration 10 sec ±1 sec Temperature +85 ºC Test Duration 1000 hrs Voltage Applied 1.25 x Vn Performance Performance Capacitance Change ∆C/C ≤ ±2% DF Change ∆tgδ ≤30 x 10–4 at 10 kHz for C ≤1.0 µF Capacitance Change ∆C/C ≤ ±5% DF Change ∆tgδ ≤30 x 10–4 at 10 kHz for C ≤1.0 µF ≤20 x 10–4 at 1 kHz for C >1.0 µF ≤20 x 10 at 1 kHz for C >1.0 µF –4 ≥ 50% of limit value Insulation Resistance RoHS Compliant Ratings Cap (µF) Catalog Part Number L T Inches H .22 .27 .33 .39 .47 .56 .68 .68 .82 .82 1.0 1.5 2.2 3.3 4.7 6.8 10.0 160224*63D–F 160274*63D–F 160334*63E–F 160394*63E–F 160474*63E–F 160564*63D–F 160684*63D–F 160684*63G–F 160824*63E–F 160824*63H–F 160105*63H–F 160155*63G–F 160225*63H–F 160335*63M–F 160475*63N–F 160685*63O–F 160106*63P–F 0.512 0.512 0.512 0.512 0.512 0.512 0.512 0.709 0.512 0.709 0.709 0.709 0.709 1.043 1.043 1.043 1.260 0.157 0.157 0.157 0.157 0.197 0.197 0.197 0.236 0.236 0.197 0.197 0.236 0.295 0.276 0.335 0.394 0.433 0.374 0.374 0.374 0.374 0.433 0.433 0.433 0.472 0.472 0.433 0.433 0.472 0.531 0.650 0.669 0.748 0.787 S Ød 63 Vdc 0.394 0.031 0.394 0.031 0.394 0.031 0.394 0.031 0.394 0.031 0.394 0.031 0.394 0.031 0.591 0.031 0.394 0.031 0.591 0.031 0.591 0.031 0.591 0.031 0.591 0.031 0.886 0.031 0.886 0.031 0.886 0.031 1.083 0.031 L 13.0 13.0 13.0 13.0 13.0 13.0 13.0 18.0 13.0 18.0 18.0 18.0 18.0 18.0 26.5 26.5 26.5 Millimeters T H S 5.0 5.0 6.0 6.0 6.0 5.0 5.0 6.0 6.0 7.5 7.5 6.0 7.5 10.0 8.5 10.0 13.0 11.0 11.0 12.0 12.0 12.0 11.0 11.0 12.0 12.0 13.5 13.5 12.5 14.0 16.0 17.0 19.0 23.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 15.0 10.0 15.0 15.0 15.0 15.0 15.0 22.5 22.5 22.5 Ød 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 * Indicates capacitance tolerance: J = ±5%, K = ±10%, M = ±20% CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com Type 160 Metallized Polyester Radial Lead Capacitors RoHS Compliant Cap (µF) Catalog Part Number L T Inches H S 100 Vdc .10 160104*100C–F 0.512 0.157 0.374 0.394 .12 160124*100C–F 0.512 0.157 0.374 0.394 .15 160154*100C–F 0.512 0.157 0.374 0.394 .18 160184*100C–F 0.512 0.157 0.374 0.394 .22 160224*100D–F 0.512 0.197 0.433 0.394 .27 160274*100D–F 0.512 0.197 0.433 0.394 .33 160334*100E–F 0.512 0.236 0.472 0.394 .33 160334*100F–F 0.709 0.197 0.433 0.591 .39 160394*100E–F 0.512 0.236 0.472 0.394 .39 160394*100F–F 0.709 0.197 0.433 0.591 .47 160474*100E–F 0.512 0.236 0.472 0.394 .47 160474*100F–F 0.709 0.197 0.433 0.591 .56 160564*100G–F 0.709 0.236 0.472 0.591 .68 160684*100G–F 0.709 0.236 0.472 0.591 .82 160824*100H–F 0.709 0.295 0.531 0.591 1.0 160105*100H–F 0.709 0.295 0.531 0.591 1.5 160155*100M–F 1.043 0.276 0.650 0.886 2.2 160225*100N–F 1.043 0.335 0.669 0.886 3.3 160335*100O–F 1.043 0.394 0.748 0.886 4.7 160475*100P–F 1.260 0.433 0.787 1.083 6.8 160685*100Q–F 1.260 0.512 0.886 1.083 10.0 160106*100S–F 1.457 0.709 1.299 1.083 160 Vdc .10 160104*160C–F 0.512 0.157 0.374 0.394 250 Vdc .033 160333*250C–F 0.512 0.157 0.374 0.394 .039 160393*250C–F 0.512 0.157 0.374 0.394 .047 160473*250C–F 0.512 0.157 0.374 0.394 .056 160563*250C–F 0.512 0.157 0.374 0.394 .068 160683*250C–F 0.512 0.157 0.374 0.394 .082 160823*250D–F 0.512 0.197 0.433 0.394 .10 160104*250D–F 0.512 0.197 0.433 0.394 .10 160104*250F–F 0.709 0.197 0.433 0.591 .12 160124*250D–F 0.512 0.236 0.472 0.394 .12 160124*250F–F 0.709 0.197 0.433 0.591 .15 160154*250E–F 0.512 0.236 0.472 0.394 .15 160154*250F–F 0.709 0.197 0.433 0.591 .18 160184*250E–F 0.512 0.236 0.472 0.394 .18 160184*250F–F 0.709 0.197 0.433 0.591 .22 160224*250F–F 0.709 0.197 0.433 0.591 .27 160274*250G–F 0.709 0.236 0.472 0.591 .33 160334*250G–F 0.709 0.236 0.472 0.591 .39 160394*250H–F 0.709 0.295 0.531 0.591 .47 160474*250H–F 0.709 0.295 0.531 0.591 .47 160474*250L–F 1.043 0.236 0.591 0.886 .56 160564*250I–F 0.709 0.335 0.571 0.591 .56 160564*250M–F 1.043 0.276 0.650 0.886 .68 160684*250I–F 0.709 0.335 0.571 0.591 .68 160684*250M–F 1.043 0.276 0.650 0.886 .82 160824*250M–F 1.043 0.335 0.669 0.886 * Indicates capacitance tolerance: J = ±5%, K = ±10%, M = ±20% Ød L T Millimeters H S Ød 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 13.0 13.0 13.0 13.0 13.0 13.0 13.0 18.0 13.0 18.0 13.0 18.0 18.0 18.0 18.0 18.0 26.5 26.5 26.5 32.0 32.0 37.0 4.0 4.0 4.0 4.0 5.0 5.0 6.0 5.0 6.0 5.0 6.0 5.0 6.0 6.0 7.5 7.5 7.0 8.5 10.0 11.0 13.0 18.0 9.5 9.5 9.5 9.5 11.0 11.0 12.0 11.0 12.0 11.0 12.0 11.0 12.0 12.0 13.5 13.5 16.5 17.0 19.0 20.0 22.5 33.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 15.0 10.0 15.0 10.0 15.0 15.0 15.0 15.0 15.0 22.5 22.5 22.5 27.5 27.5 27.5 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.031 13.0 4.0 9.5 10.0 0.8 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 13.0 13.0 13.0 13.0 13.0 13.0 13.0 18.0 13.0 18.0 13.0 18.0 13.0 18.0 18.0 18.0 18.0 18.0 18.0 26.5 18.0 26.5 18.0 26.5 26.5 4.0 4.0 4.0 4.0 4.0 5.0 5.0 5.0 6.0 5.0 6.0 5.0 6.0 5.0 5.0 6.0 6.0 7.5 7.5 6.0 8.5 7.0 8.5 7.0 8.5 9.5 9.5 9.5 9.5 9.5 11.0 11.0 11.0 12.0 11.0 12.0 11.0 12.0 11.0 11.0 12.0 12.0 13.5 13.5 15.0 14.5 16.5 14.5 16.5 17.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 15.0 10.0 15.0 10.0 15.0 10.0 15.0 15.0 15.0 15.0 15.0 15.0 22.5 15.0 22.5 15.0 22.5 22.5 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com Type 160 Metallized Polyester Radial Lead Capacitors RoHS Compliant Cap (µF) Catalog Part Number L T Inches H 1.0 1.5 2.2 3.3 4.7 6.8 160105*250N–F 160155*250O–F 160225*250P–F 160335*250Q–F 160475*250R–F 160685*250S–F 1.043 1.043 1.260 1.260 1.260 1.457 0.335 0.394 0.433 0.512 0.591 0.709 0.669 0.748 0.787 0.886 1.181 1.299 .012 .015 .018 .022 .027 .033 .039 .047 .047 .056 .068 .082 .10 .12 .15 .15 .18 .22 .27 .33 .39 .47 .56 .68 .82 1.0 1.0 160123*400C–F 160153*400C–F 160183*400C–F 160223*400C–F 160273*400C–F 160333*400D–F 160393*400D–F 160473*400E–F 160473*400F–F 160563*400F–F 160683*400F–F 160823*400F–F 160104*400G–F 160124*400G–F 160154*400H–F 160154*400L–F 160184*400L–F 160224*400L–F 160274*400M–F 160334*400M–F 160394*400N–F 160474*400N–F 160564*400O–F 160684*400P–F 160824*400P–F 160105*400P–F 160105*400Q–F 0.512 0.512 0.512 0.512 0.512 0.512 0.512 0.512 0.709 0.709 0.709 0.709 0.709 0.709 0.709 1.043 1.043 1.043 1.043 1.043 1.043 1.043 1.043 1.260 1.260 1.260 1.260 0.157 0.157 0.157 0.157 0.157 0.197 0.197 0.236 0.197 0.197 0.197 0.197 0.236 0.236 0.295 0.236 0.236 0.236 0.276 0.276 0.335 0.335 0.394 0.433 0.433 0.433 0.512 0.374 0.374 0.374 0.374 0.374 0.433 0.433 0.472 0.433 0.433 0.433 0.433 0.472 0.472 0.531 0.591 0.591 0.591 0.650 0.650 0.669 0.669 0.748 0.787 0.787 0.787 0.886 .0039 .0047 .0056 .0068 .0082 .010 .012 .015 .018 .022 .027 .033 .039 .047 .056 160392*630C–F 160472*630C–F 160562*630C–F 160682*630C–F 160822*630C–F 160103*630C–F 160123*630D–F 160153*630D–F 160183*630D–F 160223*630E–F 160273*630F–F 160333*630F–F 160393*630G–F 160473*630G–F 160563*630G–F 0.512 0.512 0.512 0.512 0.512 0.512 0.512 0.512 0.512 0.512 0.709 0.709 0.709 0.709 0.709 0.157 0.157 0.157 0.157 0.157 0.157 0.197 0.197 0.197 0.236 0.197 0.197 0.236 0.236 0.236 0.374 0.374 0.374 0.374 0.374 0.374 0.433 0.433 0.433 0.472 0.433 0.433 0.472 0.472 0.472 S 250 Vdc 0.886 0.886 1.083 1.083 1.083 1.083 400 Vdc 0.394 0.394 0.394 0.394 0.394 0.394 0.394 0.394 0.591 0.591 0.591 0.591 0.591 0.591 0.591 0.886 0.886 0.886 0.886 0.886 0.886 0.886 0.886 1.083 1.083 1.083 1.083 630 Vdc 0.394 0.394 0.394 0.394 0.394 0.394 0.394 0.394 0.394 0.394 0.591 0.591 0.591 0.591 0.591 Ød L T Millimeters H S Ød 0.031 0.031 0.031 0.031 0.031 0.031 26.5 26.5 32.0 32.0 32.0 37.0 8.5 10.0 11.0 13.0 15.0 18.0 17.0 19.0 20.0 22.5 30.0 33.0 22.5 22.5 27.5 27.5 27.5 27.5 0.8 0.8 0.8 0.8 0.8 0.8 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 26.5 26.5 26.5 26.5 26.5 26.5 26.5 26.5 32.0 32.0 32.0 32.0 4.0 4.0 4.0 4.0 4.0 5.0 5.0 6.0 5.0 5.0 5.0 5.0 6.0 6.0 7.5 6.0 6.0 6.0 7.0 7.0 8.5 8.5 10.0 11.0 11.0 11.0 13.0 9.5 9.5 9.5 9.5 9.5 11.0 11.0 12.0 11.0 11.0 11.0 11.0 12.0 12.0 13.5 15.0 15.0 15.0 16.5 16.5 17.0 17.0 19.0 20.0 20.0 20.0 22.5 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 22.5 22.5 22.5 22.5 22.5 22.5 22.5 22.5 27.5 27.5 27.5 27.5 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 18.0 18.0 18.0 18.0 18.0 4.0 4.0 4.0 4.0 4.0 4.0 5.0 5.0 5.0 6.0 5.0 5.0 6.0 6.0 6.0 9.5 9.5 9.5 9.5 9.5 9.5 11.0 11.0 11.0 12.0 11.0 11.0 12.0 12.0 12.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 15.0 15.0 15.0 15.0 15.0 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 * Indicates capacitance tolerance: J = ±5%, K = ±10%, M = ±20% CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com Type 160 Metallized Polyester Radial Lead Capacitors RoHS Compliant Cap (µF) Catalog Part Number L T Inches H S 630 Vdc .068 160683*630H–F 0.709 0.295 0.531 0.591 .068 160683*630L–F 1.043 0.236 0.591 0.886 .082 160823*630L–F 1.043 0.236 0.591 0.886 .10 160104*630L–F 1.043 0.236 0.591 0.886 .12 160124*630M–F 1.043 0.276 0.650 0.886 .15 160154*630M–F 1.043 0.276 0.650 0.886 .18 160184*630N–F 1.043 0.335 0.669 0.886 .22 160224*630N–F 1.043 0.335 0.669 0.886 .27 160274*630Q–F 1.260 0.512 0.886 1.083 .33 160334*630P–F 1.260 0.433 0.787 1.083 .39 160394*630P–F 1.260 0.433 0.787 1.083 .47 160474*630Q–F 1.260 0.512 0.886 1.083 1000 Vdc .0022 160222*1000C–F 0.512 0.157 0.374 0.394 .0027 160272*1000C–F 0.512 0.157 0.374 0.394 .0033 160332*1000C–F 0.512 0.157 0.374 0.394 .0039 160392*1000D–F 0.512 0.197 0.433 0.394 .0047 160472*1000D–F 0.512 0.197 0.433 0.394 .0056 160562*1000D–F 0.512 0.197 0.433 0.394 .0068 160682*1000D–F 0.512 0.197 0.433 0.394 .0082 160822*1000D–F 0.512 0.197 0.433 0.394 .010 160103*1000F–F 0.709 0.197 0.433 0.591 .012 160123*1000F–F 0.709 0.197 0.433 0.591 .015 160153*1000F–F 0.709 0.236 0.472 0.591 .018 160183*1000G–F 0.709 0.236 0.472 0.591 .022 160223*1000G–F 0.709 0.236 0.472 0.591 .027 160273*1000H–F 0.709 0.295 0.531 0.591 .033 160333*1000L–F 1.043 0.236 0.591 0.886 .039 160393*1000L–F 1.043 0.236 0.591 0.886 .047 160473*1000L–F 1.043 0.236 0.591 0.886 .056 160563*1000M–F 1.043 0.276 0.650 0.886 .068 160683*1000M–F 1.043 0.276 0.650 0.886 .082 160823*1000N–F 1.043 0.335 0.669 0.886 .10 160104*1000N–F 1.043 0.335 0.669 0.886 .12 160124*1000O–F 1.043 0.394 0.748 0.886 .15 160154*1000P–F 1.260 0.433 0.787 1.083 .18 160184*1000Q–F 1.260 0.512 0.886 1.083 .22 160224*1000Q–F 1.260 0.512 0.886 1.083 * Indicates capacitance tolerance: J = ±5%, K = ±10%, M = ±20% Ød L T 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 18.0 26.5 26.5 26.5 26.5 26.5 26.5 26.5 32.0 32.0 32.0 32.0 7.5 6.0 6.0 6.0 7.0 7.0 8.5 8.5 13.0 11.0 11.0 13.0 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 18.0 18.0 18.0 18.0 18.0 18.0 26.5 26.5 26.5 26.5 26.5 26.5 26.5 26.5 32.0 32.0 32.0 4.0 4.0 4.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 6.0 6.0 6.0 7.5 6.0 6.0 6.0 7.0 7.0 8.5 8.5 10.0 11.0 13.0 13.0 Millimeters H S Ød 13.5 15.0 15.0 15.0 16.5 16.5 17.0 17.0 22.5 20.0 20.0 22.5 15.0 22.5 22.5 22.5 22.5 22.5 22.5 22.5 27.5 27.5 27.5 27.5 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 9.5 9.5 9.5 11.0 11.0 11.0 11.0 11.0 11.0 11.0 12.0 12.0 12.0 13.5 15.0 15.0 15.0 16.5 16.5 17.0 17.0 19.0 20.0 22.5 22.5 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 15.0 15.0 15.0 15.0 15.0 15.0 22.5 22.5 22.5 22.5 22.5 22.5 22.5 22.5 27.5 27.5 27.5 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 Part Numbering System 160 104 K 100 C Case ROHS Series Capacitance Tolerance Voltage Code Compliant 160 392 = .0039 µF J = ±5% 100 = 100 Vdc C 103 = .01 µF K = ±10% 250 = 250 Vdc D 104 = .1 µF M = ±20% 630 = 630 Vdc E 105 = 1.0 µF 1000 = 1000 Vdc –F F etc. CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com Type 160 Metallized Polyester Radial Lead Capacitors Notice and Disclaimer: All product drawings, descriptions, specifications, statements, information and data (collectively, the “Information”) in this datasheet or other publication are subject to change. The customer is responsible for checking, confirming and verifying the extent to which the Information contained in this datasheet or other publication is applicable to an order at the time the order is placed. All Information given herein is believed to be accurate and reliable, but it is presented without any guarantee, warranty, representation or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on the knowledge that the Cornell Dubilier company providing such statements (“Cornell Dubilier”) has of operating conditions that such Cornell Dubilier company regards as typical for such applications, but are not intended to constitute any guarantee, warranty or representation regarding any such matter – and Cornell Dubilier specifically and expressly disclaims any guarantee, warranty or representation concerning the suitability for a specific customer application, use, storage, transportation, or operating environment. The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by Cornell Dubilier with reference to the use of any Cornell Dubilier products is given gratis (unless otherwise specified by Cornell Dubilier), and Cornell Dubilier assumes no obligation or liability for the advice given or results obtained. Although Cornell Dubilier strives to apply the most stringent quality and safety standards regarding the design and manufacturing of its products, in light of the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies or other appropriate protective measures) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicated in such warnings, cautions and notes, or that other safety measures may not be required. CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com