Type FCP Surface Mount Film Capacitors FCP Surface Mount Highlights: • Capacitance Range of 100 pF to .22µF • Standard EIA sizes 0603 thru 2416 • 16 and 50 Vdc Voltage Ratings • Operating Temp. Range: -55 to 125 °C • Capacitance Change from -55°C to 105°C ≤ ± 1.5% Type FCP stacked metallized polyphenylene sulfide (PPS) film capacitors offer high capacitance per unit volume, stable capacitance and D.F. over a wide temperature range, and excellent high frequency performance. Type FCP capacitors conform to standard EIA 0603, 0805, 1206, 1210, 1913 & 2416 surface mount case sizes and are packaged on tape and reel. Specifications Life Test: Capacitors subjected to 1000 hours of maximum rated temperature and 125% of the rated voltage will not have any significant visual damage, the capacitance will be within ±2% of the initial measured value, DF will be a maximum of 0.66%, and IR will be a minimum of 1000 Megohms. Nominal Capacitance Range: 100 pF to 0.22 µF (1 kHz at ≤ 5 Vrms) Capacitance Tolerance: ±5% (J) Standard,±2% (G) Optional Rated Voltage: 16 and 50 Vdc Dissipation Factor (Tan δ): 0.6% Max. (1 kHz at ≤ 5 Vrms) Operating Temperature Range: -55°C to +125°C (See Voltage derating chart for .12 - .22 µF above 105°C) Dielectric Strength: 175% of rated Vdc for 5 seconds Insulation Resistance: 3000 MΩ Min. at 20°C, after 60 seconds. (16 Vdc rated, test 10 Vdc; 50 Vdc rated, test 50 Vdc) Moisture Resistance: Capacitors subjected to 1000 hours at 40°C and 90% - 95% RH and rated voltage will not have any significant visual damage, will withstand 1.3 times the rated voltage for one minute, the capacitance will be within ±2% of the initial measured value, DF will be a maximum of 0.9%, and IR will be a minimum of 1000 Megohms. Resistance to Soldering Heat: Capacitors subjected to a 260°C reflow soldering for 5 seconds will not have any significant visual damage, dielectric strength will be as specified, the capacitance will be within ±3% of the initial measured value, DF will be a maximum of 0.66%, and IR will be a minimum of 1000 Megohms. Construction: Stacked Metallized Polyphenylene Sulfide film. 14 1605 East Rodney French Blvd. New Bedford, MA 02744 (508) 996-8564, Fax(508) 996-3830 http://www.cornell-dubilier.com E-mail: [email protected] Type FCP Surface Mount Film Capacitors Ratings Table 16 Vdc Capacitance CDE Part Number (µF) (nF) (pF) 0.00010 0.00012 0.00015 0.00018 0.00022 0.00027 0.00033 0.00039 0.00047 0.00056 0.00068 0.00082 0.0010 0.0012 0.0015 0.0018 0.0022 0.0027 0.0033 0.0039 0.0047 0.0056 0.0068 0.0082 0.01 0.012 0.015 0.018 0.022 0.027 0.033 0.039 0.047 0.056 0.068 0.082 0.10 0.12 0.15 0.18 0.22 0.10 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10.0 12.0 15.0 18.0 22.0 27.0 33.0 39.0 47.0 56.0 68.0 82.0 100.0 120 150 180 220 100 120 150 180 220 270 330 390 470 560 680 820 1000 1200 1500 1800 2200 2700 3300 3900 4700 5600 6800 8200 10000 12000 15000 18000 22000 27000 33000 39000 47000 56000 68000 82000 100000 120000 150000 180000 220000 FCP0603C101J-K1 FCP0603C121J-K1 FCP0603C151J-K1 FCP0603C181J-K1 FCP0603C221J-K1 FCP0603C271J-K1 FCP0603C331J-K1 FCP0603C391J-K1 FCP0603C471J-K1 FCP0603C561J-K1 FCP0603C681J-K1 FCP0603C821J-K1 FCP0603C102J-K1 FCP0603C122J-K1 FCP0603C152J-K1 FCP0603C182J-K1 FCP0603C222J-K1 FCP0603C272J-K1 FCP0805C332J-J1 FCP0805C392J-J1 FCP0805C472J-J1 FCP0805C562J-J1 FCP0805C682J-J1 FCP0805C822J-J2 FCP0805C103J-J2 FCP1206C123J-H1 FCP1206C153J-H1 FCP1206C183J-H1 FCP1206C223J-H1 FCP1206C273J-H2 FCP1206C333J-H2 FCP1206C393J-H3 FCP1206C473J-H3 FCP1210C563J-G2 FCP1210C683J-G2 FCP1210C823J-G3 FCP1210C104J-G3 1605 East Rodney French Blvd. New Bedford, MA 02744 (508) 996-8564, Fax(508) 996-3830 http://www.cornell-dubilier.com E-mail: [email protected] 50 Vdc Case Code 0603 0805 1206 1210 CDE Part Number FCP0805H101J-J1 FCP0805H121J-J1 FCP0805H151J-J1 FCP0805H181J-J1 FCP0805H221J-J1 FCP0805H271J-J1 FCP0805H331J-J1 FCP0805H391J-J1 FCP0805H471J-J1 FCP0805H561J-J1 FCP0805H681J-J1 FCP0805H821J-J1 FCP0805H102J-J1 FCP0805H122J-J1 FCP0805H152J-J1 FCP0805H182J-J1 FCP0805H222J-J1 FCP0805H272J-J1 FCP1206H332J-H1 FCP1206H392J-H1 FCP1206H472J-H1 FCP1206H562J-H1 FCP1206H682J-H1 FCP1206H822J-H2 FCP1206H103J-H2 FCP1210H123J-G1 FCP1210H153J-G1 FCP1210H183J-G2 FCP1210H223J-G2 FCP1210H273J-G2 FCP1210H333J-G3 FCP1210H393J-G3 FCP1913H473J-E1 FCP1913H563J-E2 FCP1913H683J-E2 FCP1913H823J-E4 FCP1913H104J-E3 FCP2416H124J-D1 FCP2416H154J-D3 FCP2416H184J-D4 FCP2416H224J-D5 Case Code 0805 1206 1210 1913 2416 15 Type FCP Surface Mount Film Capacitors Typical Temperature Characteristics Typical Frequency Characteristics Capacitance Change Capacitance Change 3 1 C/C (%) C/C (%) 2 0 -1 -2 -3 -60 -40 -20 0 20 40 60 80 10 8 6 4 2 0 -2 -4 -6 -8 -10 1 100 120 140 10 Dissipation Factor Dissipation Factor Tan δ (%) Tan (%) 0.6 0.4 0.2 0 -40 -20 0 20 40 60 80 100 120 140 .01 µF 1 10 100 1000 10000 Frequency (kHz) Insulation Resistance Im pedance 10,000 0.0082 µF 100.00 1,000 10.00 Ohms 1000 Megohms 10000 10 9 8 7 6 5 4 3 2 1 0 Temperature (°C) 100 10 1.00 0.10 -60 -40 -20 0 20 40 60 80 100 120 140 1 10 Frequency (MHz) Temperature (°C) 16 1000 Frequency (kHz) Temperature (°C) -60 100 1605 East Rodney French Blvd. New Bedford, MA 02744 (508) 996-8564, Fax(508) 996-3830 http://www.cornell-dubilier.com E-mail: [email protected] 100 Type FCP Surface Mount Film Capacitors Outline Dimensions L W T t t Outline Dimensions (in.) Case Size Code L±0.008 0603 0.063 0805 0.079 1206 0.126 1210 0.126 1913 0.189 2416 0.236 W T±0.008 t 0.032±0.006 0.028±0.006 0.035 0.049±0.008 0.043 0.035 0.063±0.008 0.043 0.059 0.043 0.098±0.008 0.059 0.083 0.055 0.079 0.130±0.012 0.110 0.094 0.071 0.094 0.161±0.012 0.110 0.126 Outline Dimensions (mm) Case Size (metric) L±0.2 W T±0.2 t 0.014±0.008 1608 1.6 0.018±0.010 2012 2.0 0.026±0.012 3216 3.2 0.026±0.012 3225 3.2 0.014±0.008 4833 4.8 0.014±0.008 6041 6.0 Packaging Code 0.80±0.15 0.7±0.15 0.35±0.2 0.9 1.25±0.2 0.45±0.25 1.1 0.9 1.6±0.2 0.65±0.3 1.1 1.5 1.1 2.5±0.2 0.65±0.3 1.5 2.1 1.4 2.0 3.3±0.3 0.35±0.2 2.8 2.4 1.8 2.4 4.1±0.3 0.35±0.2 2.8 3.2 K1 J1 J2 H1 H2 H3 G1 G2 G3 E1 E2 E3 E4 D1 D3 D4 D5 Pulse Handling Capability Capacitance (µF) Voltage (Vdc) dV/dt (volts/µsec) Capacitance (µF) Voltage (Vdc) 0.0001 0.00012 0.00015 0.00018 0.00022 0.00027 0.00033 0.00039 0.00047 0.00056 0.00068 0.00082 0.001 0.0012 0.0015 0.0018 0.0022 0.0027 0.0033 0.0039 0.0047 0.0056 0.0068 0.0082 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 420 390 350 325 295 270 245 225 205 193 175 160 150 135 123 115 105 95 86 80 74 68 62 58 0.01 0.012 0.015 0.018 0.022 0.027 0.033 0.039 0.047 0.056 0.068 0.082 0.1 0.0001 0.00012 0.00015 0.00018 0.00022 0.00027 0.00033 0.00039 0.00047 0.00056 0.00068 16 16 16 16 16 16 16 16 16 16 16 16 16 50 50 50 50 50 50 50 50 50 50 50 dV/dt Capacitance (volts/µsec) (µF) 1605 East Rodney French Blvd. New Bedford, MA 02744 (508) 996-8564, Fax(508) 996-3830 http://www.cornell-dubilier.com E-mail: [email protected] 52 48 43 40 37 33 31 28 26 24 22 20 19 1100 1050 940 890 800 730 690 610 580 520 480 0.00082 0.001 0.0012 0.0015 0.0018 0.0022 0.0027 0.0033 0.0039 0.0047 0.0056 0.0068 0.0082 0.01 0.012 0.015 0.018 0.022 0.027 0.033 0.039 .047 - 0.1 0.12 - 0.22 Voltage (Vdc) dV/dt (volts/µsec) 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 440 400 370 340 310 270 260 240 220 200 190 170 160 145 135 120 110 100 94 86 78 180 130 17 Type FCP Surface Mount Film Capacitors Voltage Derating vs. Temperature Percentage of Rated Voltage (%) 120 FCP 100 pF - 0.1µF 100 80 If the temperature on the surface of the capacitor is above 105°C, then the maximum voltage for FCP 50 Vdc ratings from .12 µF to .22µF must be derated linearly from full rated voltage at 105°C to 75% of the rated voltage at 125°C. FCP (0.12µF - 0.22µF@50 Vdc) 60 40 20 0 -60 -40 -20 0 20 40 60 80 100 120 140 Temperature (°C) Vrms vs. Frequency Maximum AC Voltage FCP 16 Vdc Series Maximum AC Voltage FCP 50 Vdc Series 100 100 40 Vrms 30 Vrms Vrms Vrms 100 pF - 0.1 µF 11 Vrms 10 0.0018 µF 0.01 µF 10 0.039 µF 0.1 µF 100 pF - 0.039 µF: 30 Vrms Max. 0.047 µF - 0.22 µF: 40 Vrms Max. 1 0.22 µF 1 10 100 1000 10 100 10 Frequency (kHz) Frequency (kHz) The capacitor surface temperature should not exceed 125°C. Typical Applications Resonant Circuit for Inverter: Liquid Crystal Display Panel Higher efficiency in battery operated devices. Dissipation Factor(loss) vs. Frequency 6 FCP 4 D.F. (%) DC / DC Converter MLCC X7R/0.1µF 2 FCP 0.1µF 0 1 10 100 1000 10000 Frequency (kHz) Very low losses and stable temperature characteristics make film chip capacitors the best choice for resonant circuit applications. 18 1605 East Rodney French Blvd. New Bedford, MA 02744 (508) 996-8564, Fax(508) 996-3830 http://www.cornell-dubilier.com E-mail: [email protected] Type FCP Surface Mount Film Capacitors Typical Applications Filtering Capacitor for xDSL: Telephone Line Impedance vs. Frequency (Typical Performance FCP Series) FCN 250 V 400 V Impednace (Ohms) 100 FCP FCP FCP 10 1 FCP 0.0033µF 0.1 0.01µF 0.1µF 0.01 1 10 100 1000 10000 Frequency (MHz) Capacitance Change vs. Bias Voltage Capacitance Change vs. Temperature 5 Capacitance Change (%) Capaciance Cange (%) 2 0 FCP PPS Film Capacitor .010 µF -2 MLCC X7R 0.01µF -4 -6 0 FCP 0.01 µF -5 -10 MLCC X7R 0.01µF -15 -20 -20 -10 0 10 20 -60 -40 -20 Bias Voltge (Vdc) 0 20 40 60 80 100 120 140 Temperature (°C) The capacitance of SMT film chips is much more stable with applied voltage and with changes in temperature than multilayer ceramic capacitors. Add in the low e.s.r. characteristics of film chips and the final result is improved performance in filter circuit applications. PLL Circuit: Cellular phone, Blue Tooth, Data Communication Cards Lock-up Time Loop Filter Charge Pump Tantalum VCO MLCC X7R FCP 0 100 FCP 200 300 400 FCP 500 Time (µs) In PLL circuit applications, FCP SMT film capacitor advantages are tight tolerance on the capacitance value, stable capacitance with temperature, faster lock-up times, and no noise due to piezoelectric effects 1605 East Rodney French Blvd. New Bedford, MA 02744 (508) 996-8564, Fax(508) 996-3830 http://www.cornell-dubilier.com E-mail: [email protected] 19 Types FCN, FCP, FCA Surface Mount Film Capacitors Reel Quantity and Dimensions Packaging Code K1 J1, J2 H1, H2 H3 G1, G2, G3 E1, E2 E3, E4 D1, D2 D3, D4, D5 B, Z U, V, X, Y S, T Tape Width [mm] 8 8 8 8 8 12 12 12 12 12 16 24 Reel Diameter [in.(mm)] 7 (178) 7 (178) 7 (178) 7 (178) 7 (178) 13 (330) 13 (330) 13 (330) 13 (330) 13 (330) 13 (330) 13 (330) Quantity/Reel 4000 3000 3000 2000 2000 3000 2000 3000 2000 1500 1000 750 Symbol A C D E N r W1 W2 8 mm Tape 178 13 21 2 60 1 9.5 1.2 Reel Dimensions (mm) 12 mm Tape 16 mm Tape 330 330 13 13 21 21 2 80 80 1 14 17.5 2 - 24 mm Tape 330 13 21 80 25.5 - Tape Dimensions (mm) Tape Dimensions (mm) Symbol W F E P1 P2 P0 D0 D1 K1 8 3.5 1.75 2 4 1.5 - J1,J2, H1,H2,H3,G1,G2,G3 8 3.5 1.75 4 2 4 1.5 1 E1, E2 E3, E4 12 5.5 1.75 8 2 4 1.5 1.5 D1, D2, D3, D4, D5, B, Z 12 5.5 1.75 8 2 4 1.5 - U, V X, Y 16 7.5 1.75 12 2 4 1.5 1.5 1605 East Rodney French Blvd. New Bedford, MA 02744 (508) 996-8564, Fax(508) 996-3830 http://www.cornell-dubilier.com E-mail: [email protected] S, T 24 11.5 1.75 16 2 4 1.5 1.5 Type A ±0.1 B ±0.1 T ±0.05 T2 ±0.2 K ±0.1 K1 J1 J2 H1, H2 H3 G1, G2 G3 E1 E2 E3, E4 D1 D3, D4 D5 B Z X, Y U, V S, T 1.0 1.55 1.55 1.9 1.9 2.8 2.8 3.8 3.8 3.8 4.6 4.6 4.6 5.5 5.5 6.91 8.94 10.8 1.85 2.3 2.3 3.5 3.5 3.5 3.5 5.1 5.1 5.1 6.3 6.3 6.3 6.3 7.5 8.43 10.54 16.0 0.2 0.25 0.25 0.25 0.25 0.25 0.25 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.34±.02 0.34±.02 0.36±.02 1.1 1.3 1.5 1.5 1.9 1.9 2.5 2.0 2.6 3.4 2.7 3.5 4.6 5.1 4.7 5.69 5.8 5.82 1.0 1.2 1.4 1.4 1.8 1.8 2.4 1.9 2.5 3.5 2.6 3.4 4.5 5.0 4.6 5.64 5.75 5.77 25 Types FCN, FCP, FCA Surface Mount Film Capacitors Recommended Land Patterns Capacitor Outline Land Dimensions [in.(mm)] Case Size Code Land 0603 0805 1206 1210 1913 2416 2420 2820 2825 3022 3925 3931 6031 6040 Land C A B A 0.024 0.03 0.07 0.07 0.10 0.15 0.15 0.18 0.18 0.20 0.28 0.28 0.50 0.50 B (0.6) (0.8) (1.8) (1.8) (2.6) (3.8) (3.8) (4.5) (4.5) (5.1) (7.2) (7.2) (12.6) (12.6) 0.08 0.09 0.14 0.14 0.26 0.31 0.31 0.35 0.35 0.38 0.47 0.47 0.68 0.68 C (2.0) (2.4) (3.6) (3.6) (6.6) (7.8) (7.8) (9.0) (9.0) (9.7) (11.9) (11.9) (17.3) (17.3) 0.028 0.04 0.06 0.09 0.12 0.15 0.18 0.18 0.22 0.20 0.22 0.28 0.28 0.35 (0.7) (1.1) (1.4) (2.3) (3.0) (3.8) (4.6) (4.6) (5.7) (5.0) (5.7) (7.2) (7.2) (9.0) Soldering Information Recommended Reflow Soldering Conditions Soldering Reflow method only, not to exceed two reflow processings. Halogen content of flux, solder paste and cleaner should be less than 0.1% for each. Peak Temperature Cleaning Solvent Isopropyl alcohol Cleaning Method Temperature Immersion 25°C Vapor <50°C Ultrasonic <50°C Time <5min. <5min. <5min. Capacitor Type FCN 16 V, 50 V, 100 V (.001 - .01 µF) FCN 100 V (.012 - 1.0 µF), 250 V, 400 V FCP FCA Dry the circuit board completely after cleaning. Maximum Capacitor Surface Temperature (°C) 240 230 260 240 Recommended Peak Reflow Temperature (°C) Maximum 30 Seconds at or above (°C) 230 220 230 230 210 210 230 210 Ordering Information Type Case Size Voltage Code Capacitance Code Tolerance Code FCN 1913 C 124 J C = 16 Vdc H = 50 Vdc A = 100 Vdc E = 250 Vdc G = 400 Vdc 124 = 120000 pF = .12 µF J= 5% K = 10 % FCP 1206 C C = 16 Vdc H = 50 Vdc FCA 1206 A A = 10 Vdc C = 16 Vdc 393 J 393 = 39000 pF = .039 µF J= 5% G= 2% 105 M 105 = 1000000 pF = 1.0 µF M = 20 % 1605 East Rodney French Blvd. New Bedford, MA 02744 (508) 996-8564, Fax(508) 996-3830 http://www.cornell-dubilier.com E-mail: [email protected] - Packaging Code E1 H3 H3 (See Reel Quantity Table for an explanation of the Packaging Code) 7015 Rev. 2