Type FCA Surface Mount Film Capacitors FCA Surface Mount Highlights: • Smallest Film Chips 1 µf/10 V in 1206 case • Non-Polarized • No Piezoelectric Effects • Low E.S.R Type FCA acrylic film chips are non-inductive stacked metallized film capacitors which feature large capacitance values in standard surface mount case sizes. Filtering • Decoupling • Noise Attenuation • Distortion Free Audio Type FCA acrylic film capacitors offer high capacitance values in standard surface mount case sizes. They excel in attenuating DC power bus noise, and as ripple filters in dc to dc power conversion circuits. A s coupling capacitors in audio circuits, they yield distortion free sound and better high frequency filtering. The new 1 µF/ 10 V rating offers a film capacitor that is a direct replacement for tantalum “A” case capacitors. The nonpolar FCA capacitor has lower e.s.r. and lower DCL than an equivalent tantalum capacitor, and in high frequency applications it takes a tantalum capacitor with ten times the capacitance to perform as well as the FCA capacitor. The capacitor is constructed of noninductive stacked layers of metallized acrylic resin film with solder plated copper alloy terminals. Ratings Table Capacitance (µ F) Voltage Rating (Vdc) CDE Part Number 1.0 10 FCA1206A105M-H3 3 0.10 16 FCA0805C104M-J2 0.15 16 0.22 20 dV/dt (V/µs) 10kHz Maximum Current (Arms) 20kHz 50kHz 0.60 0.76 1.05 1.22 1.35 1.43 1.43 19 0.15 0.21 0.3 0.375 0.46 0.58 0.65 FCA1206C154M-H1 15 0.21 0.28 0.37 0.45 0.54 0.62 0.68 16 FCA1206C224M-H1 13 0.25 0.33 0.45 0.55 0.66 0.76 0.84 0.33 16 FCA1206C334M-H2 10 0.35 0.45 0.61 0.74 0.84 0.94 1.00 0.47 16 FCA1206C474M-H3 7 0.39 0.52 0.71 0.86 1.00 1.10 1.17 0.68 16 FCA1206C684M-H3 5 0.48 0.625 0.85 1.04 1.19 1.31 1.34 1.0 16 FCA1210C105M-G2 3 0.60 0.78 1.05 1.25 1.38 1.46 1.46 1605 East Rodney French Blvd. New Bedford, MA 02744 (508) 996-8564, Fax(508) 996-3830 http://www.cornell-dubilier.com E-mail: [email protected] 100kHz 200kHz 500kHz 1MHz Type FCA Surface Mount Film Capacitors Specifications Operating Temperature Range; -40ºC to +85ºC Life Test; Apply 125% of the rated DC working voltage at 85ºC for 1000 hours, and then stabilize them to +20ºC. Capacitors will meet the following limits: ∆C = +7%/-20% of the initial measured value DF ≤ 1.65% (at 1kHz) I.R. > 300MΩ (C ≤ 0.33µF) I.R. > 100MΩ •µF(C > 0.33µF) Capacitance Tolerance; ±20% at 1 kHz and +20ºC Dissipation Factor (DF); It’s no more than 0.015 at 1 kHz and +20ºC. Dielectric Strength; 175% of rated voltage for 5 seconds Moisture Resistance; After 500 hours with rated voltage applied at +40ºC and 90 to 95% R.H., the capacitor will meet the following limits: ∆C = +20/-3% of the initial measured value DF ≤ 2.25% (at 1kHz) I.R. > 100MΩ (C ≤ 0.33µF) I.R. > 30MΩ •µF(C > 0.33µF) Dielectric Strength: Capacitor will withstand 130% of the rated voltage for 1 minute. Insulation Resistance (I.R.); After 1 minute @ 10Vdc (+20°C), I.R. > 1000MΩ (C ≤ 0.33µF) I.R. > 300MΩ •µF (C > 0.33µF) Ac Voltage Rating: 12 Volts rms Resistance to Soldering Heat; The capacitors can withstand being heated in an oven at 235ºC for 200 seconds. Outline Drawing S S H L W Outline Dimensions English Metric Part Number Suffix Case Code L W H S L W H S (±.008in.) (±.008in.) (±.008in.) (±.012in.) (±0.2mm) (±0.2mm) (±0.2mm) (±0.3mm) J2 0805 0.079 0.049 0.039 0.018 2.0 1.25 1.0 0.45 H1 1206 0.126 0.063 0.032 0.026 3.2 1.6 0.8 0.65 H2 1206 0.126 0.063 0.039 0.026 3.2 1.6 1.0 0.65 H3 1206 0.126 0.063 0.055 0.026 3.2 1.6 1.4 0.65 G2 1210 0.126 0.098 0.055 0.026 3.2 2.5 1.4 0.65 1605 East Rodney French Blvd. New Bedford, MA 02744 (508) 996-8564, Fax(508) 996-3830 http://www.cornell-dubilier.com E-mail: [email protected] 21 Type FCA Surface Mount Film Capacitors Frequency Characteristics Temperature Characteristics Capacitance Change 10 Capacitance Change 0.33uF 6 Capacitance Change (%) 8 Capacitance Change (%) 0.1uF 8 (Typical) 10 6 4 2 0 -2 -4 1.0uF 4 2 0 -2 -4 -6 -6 -8 -8 -10 -10 -60 -40 -20 0 20 40 60 80 1 100 10 100 1,000 10,000 1,000 10,000 Frequency (kHz) Temperature (°C) Dissipation Factor Dissipation Factor 10 (Typical) 2 9 0.1uF .33uF 8 1.0uF D.F. (%) D.F. (%) 7 1 6 5 4 3 2 1 0 0 -60 -40 -20 0 20 40 60 80 1 100 10 100 Frequency (kHz) Temperature (ºC) Impedance 10000.00 Insulation Resistance 0.1uF 1000 1000.00 .33uF 1.0uF Impedance (ohms) I. R. (1000 MegOhms) 0.1uF 0.33uF 1.0uF 100 10 100.00 10.00 1.00 0.10 1 0.01 -60 -40 -20 0 20 40 60 80 100 1 10 Temperature (ºC) 22 100 Frequency (kHz) 1605 East Rodney French Blvd. New Bedford, MA 02744 (508) 996-8564, Fax(508) 996-3830 http://www.cornell-dubilier.com E-mail: [email protected] 1,000 10,000 Type FCA Surface Mount Film Capacitors Typical Applications Coupling Capacitor for Audio: + _ FCA + _ Sound Signal ESR vs. Frequency Comparison Total Harmonic Distortion 100 0.06 Aluminum Electrolytic 0.1µF @ 16 Vdc 10 E.S.R. (Ohms) Distortion (%) 0.08 0.04 0.02 Tantalum 0.1µF @ 16 Vdc 1 FCA 0.1µF @ 16 Vdc 0.1 0 FCA 0.47µF MCLL 0.47µF Tantalum 0.47µF 0.01 1 10 100 1000 10000 Frequency (kHz) Using FCA capacitors in audio circuits can result in lower sound distortion. The low e.s.r., the absence of piezoelectric effects, and the non polar nature of the capacitor will eliminate sources of distortion in your audio circuits. PLL Circuit: Cellular phone, Blue Tooth, Data Communication Card Lock-up time Phase Lock Loop Filter Charge Pump (.33 µF) VCO MLCC X7R Tantalum FCA FCA FCA 0 1 2 3 4 5 6 Time (ms) FCA surface mount film capacitors have advantages over tantalum and ceramic capacitors in PLL circuits. There are no piezoelectric effects to create noise, they are not polarized, and they result in faster signal lock-up time. 1605 East Rodney French Blvd. New Bedford, MA 02744 (508) 996-8564, Fax(508) 996-3830 http://www.cornell-dubilier.com E-mail: [email protected] 23 Type FCA Surface Mount Film Capacitors Typical Applications Filtering Performance: 10 Vdc FCA Switching Power Supply 200 kHz Oscilloscope In the above circuit, one 1 µF FCA capacitor results in the same ripple reduction performance as a 10 µF tantalum capacitor at 200 kHz. With a 1 µF tantalum capacitor in the circuit the measured ripple voltage was 70 mVpp, and with a 10 µF tantalum or a 1 µF FCA capacitor the ripple voltage was 8 mVpp. Impedance vs. Frequency Comparison Capacitance Change vs. Temperature Capacitance Change (%) Impedance (Ohms ) 1000 100 10 Tantalum 1.0µF 1 MLCC 1.0µF 0.1 FCA 1.0µF 0.01 1 10 100 1000 10000 30 20 10 Tantalum 1.0µF 0 -10 MLCC X7R 1.0 µF FCA Acrylic Film 1.0 µF -20 -30 -60 -40 -20 0 20 40 60 Temperature (°C) Frequency (kHz) Type FCA capacitors have very low e.s.r. and stable capacitance vs. temperature. Design Kits Information on design kits for many CDE products is available at the CDE Web site. Kits containing various ratings of FCA, FCN, and FCP surface mount film products are offered. Also available are kits for aluminum electrolytic, polymer aluminum, and mica surface mount capacitors. Visit us at www.cornell-dubilier.com 24 1605 East Rodney French Blvd. New Bedford, MA 02744 (508) 996-8564, Fax(508) 996-3830 http://www.cornell-dubilier.com E-mail: [email protected] 80 100 Types FCN, FCP, FCA Surface Mount Film Capacitors Reel Quantity and Dimensions Packaging Code K1 J1, J2 H1, H2 H3 G1, G2, G3 E1, E2 E3, E4 D1, D2 D3, D4, D5 B, Z U, V, X, Y S, T Tape Width [mm] 8 8 8 8 8 12 12 12 12 12 16 24 Reel Diameter [in.(mm)] 7 (178) 7 (178) 7 (178) 7 (178) 7 (178) 13 (330) 13 (330) 13 (330) 13 (330) 13 (330) 13 (330) 13 (330) Quantity/Reel 4000 3000 3000 2000 2000 3000 2000 3000 2000 1500 1000 750 Symbol A C D E N r W1 W2 8 mm Tape 178 13 21 2 60 1 9.5 1.2 Reel Dimensions (mm) 12 mm Tape 16 mm Tape 330 330 13 13 21 21 2 80 80 1 14 17.5 2 - 24 mm Tape 330 13 21 80 25.5 - Tape Dimensions (mm) Tape Dimensions (mm) Symbol W F E P1 P2 P0 D0 D1 K1 8 3.5 1.75 2 4 1.5 - J1,J2, H1,H2,H3,G1,G2,G3 8 3.5 1.75 4 2 4 1.5 1 E1, E2 E3, E4 12 5.5 1.75 8 2 4 1.5 1.5 D1, D2, D3, D4, D5, B, Z 12 5.5 1.75 8 2 4 1.5 - U, V X, Y 16 7.5 1.75 12 2 4 1.5 1.5 1605 East Rodney French Blvd. New Bedford, MA 02744 (508) 996-8564, Fax(508) 996-3830 http://www.cornell-dubilier.com E-mail: [email protected] S, T 24 11.5 1.75 16 2 4 1.5 1.5 Type A ±0.1 B ±0.1 T ±0.05 T2 ±0.2 K ±0.1 K1 J1 J2 H1, H2 H3 G1, G2 G3 E1 E2 E3, E4 D1 D3, D4 D5 B Z X, Y U, V S, T 1.0 1.55 1.55 1.9 1.9 2.8 2.8 3.8 3.8 3.8 4.6 4.6 4.6 5.5 5.5 6.91 8.94 10.8 1.85 2.3 2.3 3.5 3.5 3.5 3.5 5.1 5.1 5.1 6.3 6.3 6.3 6.3 7.5 8.43 10.54 16.0 0.2 0.25 0.25 0.25 0.25 0.25 0.25 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.34±.02 0.34±.02 0.36±.02 1.1 1.3 1.5 1.5 1.9 1.9 2.5 2.0 2.6 3.4 2.7 3.5 4.6 5.1 4.7 5.69 5.8 5.82 1.0 1.2 1.4 1.4 1.8 1.8 2.4 1.9 2.5 3.5 2.6 3.4 4.5 5.0 4.6 5.64 5.75 5.77 25 Types FCN, FCP, FCA Surface Mount Film Capacitors Recommended Land Patterns Capacitor Outline Land Dimensions [in.(mm)] Case Size Code Land 0603 0805 1206 1210 1913 2416 2420 2820 2825 3022 3925 3931 6031 6040 Land C A B A 0.024 0.03 0.07 0.07 0.10 0.15 0.15 0.18 0.18 0.20 0.28 0.28 0.50 0.50 B (0.6) (0.8) (1.8) (1.8) (2.6) (3.8) (3.8) (4.5) (4.5) (5.1) (7.2) (7.2) (12.6) (12.6) 0.08 0.09 0.14 0.14 0.26 0.31 0.31 0.35 0.35 0.38 0.47 0.47 0.68 0.68 C (2.0) (2.4) (3.6) (3.6) (6.6) (7.8) (7.8) (9.0) (9.0) (9.7) (11.9) (11.9) (17.3) (17.3) 0.028 0.04 0.06 0.09 0.12 0.15 0.18 0.18 0.22 0.20 0.22 0.28 0.28 0.35 (0.7) (1.1) (1.4) (2.3) (3.0) (3.8) (4.6) (4.6) (5.7) (5.0) (5.7) (7.2) (7.2) (9.0) Soldering Information Recommended Reflow Soldering Conditions Soldering Reflow method only, not to exceed two reflow processings. Halogen content of flux, solder paste and cleaner should be less than 0.1% for each. Peak Temperature Cleaning Solvent Isopropyl alcohol Cleaning Method Temperature Immersion 25°C Vapor <50°C Ultrasonic <50°C Time <5min. <5min. <5min. Capacitor Type FCN 16 V, 50 V, 100 V (.001 - .01 µF) FCN 100 V (.012 - 1.0 µF), 250 V, 400 V FCP FCA Dry the circuit board completely after cleaning. Maximum Capacitor Surface Temperature (°C) 240 230 260 240 Recommended Peak Reflow Temperature (°C) Maximum 30 Seconds at or above (°C) 230 220 230 230 210 210 230 210 Ordering Information Type Case Size Voltage Code Capacitance Code Tolerance Code FCN 1913 C 124 J C = 16 Vdc H = 50 Vdc A = 100 Vdc E = 250 Vdc G = 400 Vdc 124 = 120000 pF = .12 µF J= 5% K = 10 % FCP 1206 C C = 16 Vdc H = 50 Vdc FCA 1206 A A = 10 Vdc C = 16 Vdc 393 J 393 = 39000 pF = .039 µF J= 5% G= 2% 105 M 105 = 1000000 pF = 1.0 µF M = 20 % 1605 East Rodney French Blvd. New Bedford, MA 02744 (508) 996-8564, Fax(508) 996-3830 http://www.cornell-dubilier.com E-mail: [email protected] - Packaging Code E1 H3 H3 (See Reel Quantity Table for an explanation of the Packaging Code) 7015 Rev. 2