r461jk-480823 sw, sp6t, latching self cut-off, 16 pin idc - Dow-Key

REVISIONS
REV.
DESCRIPTION
A
Part Number
24 Vdc
R461JK-480823
A
A
A
A
A
A
SHEET NO.
1
2
3
4
5
6
APPROVALS
07/22/13
ENGINEERING
T. JOHNSON
7/14/2014
S. LYNCH
7/16/2014
QUALITY
MANUFACTURING
J. LEE
7/16/2014
APPROVED
K.R.
4822 McGrath Street
Ventura, CA. 93003-5641
PH: (805) 650-0260
FAX: (805) 650-1734
DATE
DRAWN
SARA LEE
PRODUCTION RELEASE
Nominal
Coil Voltage
REVISIONS
DATE
7/17/14
TECHNOLOGIES COMPANY
SW, SP6T, LATCHING SELF CUT-OFF, 16 PIN IDC CONN.
SMA-FEMALE CONNECTORS, INDICATORS
50 OHM [1W] INT TERMINATIONS, 5 MIL CYCLE, 26.5GHz
CODE IDENT. NO.
00471
SCALE
NONE
DWG. NO.
R461JK-480823
FINAL ASSY: R461JK-480823
SHEET
1
OF
6
04-0004 REV. C 5/27/10
OUTLINE DRAWING:
.585
14.9
16 PIN IDC CONNECTOR
PIN 1
2.234
56.7
2.570
65.3
.086
2.2
.331
8.4
7X SMA-FEMALE CONNECTORS
6X EQ. SPACED ON 1.062 [27.0] B.C.
2.250
57.2
1.800
45.7
4X
UNLESS OTHERWISE
SPECIFIED TOLERANCES
ARE:
[ ] MILLIMETERS
.XXX ±.010
.XX
±.030
CODE IDENT. NO.
00471
.172 [4.4] THRU
DWG. NO.
REV.
R461JK-480823
A
ANGLES: ±3°
SCALE
NONE
FINAL ASSY: XXX
SHEET 2 OF 6
04-0005 REV. B 9/21/06
SPECIFICATION:
1.0
2.0
RF CHARACTERISTICS:
1.1
FREQUENCY (GHz):
DC - 4
4 - 12.4
12.4 - 18
18 - 26.5
1.2
VSWR (RATIO MAX):
1.20:1
1.35:1
1.45:1
1.70:1
1.3
INSERTION LOSS (dB MAX):
1.4
ISOLATION (dB MAX):
100
80
70
65
1.5
IMPEDANCE (NOMINAL):
50
50
50
50
1.6
THIRD ORDER INTER MODULATION:
1.7
REPEATABILITY (MAX):
4.0
-120 dBc typical (2 carriers 20W)
0.03 dB @ 25o C
ACTUATION DATA:
2.1
OPERATING MODE:
LATCHING
2.2
OPERATING VOLTAGE:
20 - 32 Vdc (24Vdc NOMINAL)
2.3
COIL RESISTANCE:
132 OHMS
2.4
OPERATING CURRENT:
195 mA @ 25o C TYPICAL
2.5
STAND-BY CURRRENT:
50 mA
2.6
INDICATOR SPECIFICATIONS:
2.7
3.0
0.3 + 0.015 x frequency (GHz)
2.7.1 MAXIMUM WITHSTANDING VOLTAGE:
60V
2.7.2 MAXIMUM CURRENT CAPACITY:
150 mA
2.7.3 MAXIMUM <<ON>> RESISTANCE:
2.5 Ω
2.7.4 MAXIMUM <<OFF>> RESISTANCE:
10 G Ω
SWITCHING TIME:
15 mS MAX
MECHANICAL:
3.1
DESIGN LIFE:
5 MILLION CYCLES MIN
3.2
ACTUATOR TERMINAL:
16 PIN, IDC CONNECTOR (.1" SPACING)
3.3
WEIGHT:
250 g MAX
ENVIRONMENTAL:
4.1
OPERATING TEMPERATURE:
-25o C TO +75o C
4.2
STORAGE TEMPERATURE:
-55o C TO +85o C
4.3
TEMPERATURE CYCLING:
-55o C TO +85o C (10 CYCLES)
4.4
VIBRATION: OPERATING
7g: 5-2000 Hz @ 0.25 IN P-P
4.4.1 SURVIVAL
20g: 20-2000 Hz @ 0.06 IN P-P 4 MIN/CYCLE, 4 CYCLES/AXIS
4.4.2 RANDOM
2.41g (rms ) 10 MIN/ AXIS
4.5
SHOCK:
HALF-SINE: 500g @ 0.5ms, 3 DROPS/DIRECTION, 18 TOTAL
4.5.1 OPERATING
50g @ 6ms, 6 DIRECTIONS
4.6
MOISTURE RESISTANCE:
65o C, 95% RH, 10 DAYS
4.7
ALTITUDE STORAGE:
50,000 FEET (15,240 METERS)
4.8
RFI:
55 dB at 20 GHz
4.9
MAGNETIC FIELD:
< 6 GAUSS 1/4" FROM SURFACE
CODE IDENT. NO.
00471
SCALE
NONE
DWG. NO.
REV.
R461JK-480823
FINAL ASSY: R461JK-480823
A
SHEET 3 OF 6
04-0005 REV. B 9/21/06
SUPPLEMENTAL SPECIFICATIONS:
MAX incident CW Power (cold switching) vs. Frequency
Power Handling at 25 C is 30 W at 4 GHz
Reference conditions:
•
Cold switching only (NO hot switching)
•
Ambient temperature of 75 C or less
•
Sea level (0.88 derating @ 15,000 ft)
•
Load VSWR < 1.2 (see graph for derating above 1.2 VSWR)
Power Derating Factor vs. VSWR
CODE IDENT. NO.
00471
SCALE
NONE
DWG. NO.
REV.
R461JK-480823
FINAL ASSY: R461JK-480823
A
SHEET 4 OF 6
04-0005 REV. C 5/27/10
DRIVING THE SWITCH:
DRIVE
+24 Vdc
INDICATOR
1
2
Ind Common
Path 1
Ind. 1
Path 2
Ind. 2
Path 3
Ind. 3
Path 4
Ind. 4
Path 5
Ind. 5
Path 6
Ind. 6
Common Gnd
15
16
Open All Paths
Each RF path can be closed by applying Ground to the corresponding "drive" pin. Any non-driven path
will be simultaneously opened by internal logic.
Standard drive:
•
Connect pin 15 to ground.
•
Connect pin 1 to supply (+20Vdc to +32Vdc)
•
Select (close) desired RF path by applying Ground to the corresponding "drive" pin
(Ex: apply Ground to pin 3 to close RF path 1).
•
To select another path, ensure that all unwanted RF path "drive" pins are disconnected
from Ground (to prevent multiple RF path engagement). Apply Ground to the "drive" pin
which corresponds to the desired RF path.
•
To open all RF paths, ensure that all RF path "drive" pins are disconnected from Ground.
Complete the operation by applying Ground to pin 16.
Break-Before-Make
Open the undesired RF path. After 15 mS (minimum), close the new RF path.
Make-Before-Break
Ensure that the previously selected RF path "drive" is connected to Ground, then close the new
RF path. The previously selected path can then be de-selected.
CODE IDENT. NO.
00471
SCALE
NONE
DWG. NO.
REV.
R461JK-480823
FINAL ASSY: R461JK-480823
A
SHEET 5 OF 6
04-0005 REV. B 9/21/06
ELECTRONIC POSITION INDICATORS:
The electronic position indicators consist of optically isolated, solid state relays which are driven by, photoelectric sensors coupled to the mechanical position of the RF paths moving elements. The circuitry consists
of a common which can be connected to an output corresponding to the selected RF path. If one or more
RF paths are closed, the corresponding indicators will be connected to the common. The solid state relays
are configured for AC and/or DC operation. The electronic position indicators require the supply (20 to
32 Vdc) to be connected to pin 1 and Ground connected to pin 15.
Pin Number
Function
2
Indicator Common
4
Indicator RF Path 1
6
Indicator RF Path 2
8
Indicator RF Path 3
10
Indicator RF Path 4
12
Indicator RF Path 5
14
Indicator RF Path 6
CODE IDENT. NO.
00471
SCALE
NONE
DWG. NO.
REV.
R461JK-480823
FINAL ASSY: R461JK-480823
A
SHEET 6 OF 6
04-0005 REV. B 9/21/06