PD-97506 IR3856WMPbF SupIRBuck HIGHLY EFFICIENT TM INTEGRATED 6A, SYNCHRONOUS BUCK REGULATOR Features • • • • • • • • • • • • • • • • • • • Description Greater than 95% Maximum Efficiency Wide Input Voltage Range 1.5V to 16V Wide Output Voltage Range 0.7V to 0.9*Vin Continuous 6A Load Capability Integrated Bootstrap-diode High Bandwidth E/A for excellent transient performance Programmable Switching Frequency up to 1.5MHz Programmable Over Current Protection PGood output Hiccup Current Limit Precision Reference Voltage (0.7V, +/-1%) Programmable Soft-Start Enable Input with Voltage Monitoring Capability Enhanced Pre-Bias Start-up Seq input for Tracking applications -40oC to 125oC operating junction temperature Thermal Protection 4mm x 5mm Power QFN Package Halogen Free, Lead Free and RoHS compliant The IR3856W SupIRBuckTM is an easy-to-use, fully integrated and highly efficient DC/DC synchronous Buck regulator. The MOSFETs copackaged with the on-chip PWM controller make IR3856W a space-efficient solution, providing accurate power delivery for low output voltage applications. IR3856W is a versatile regulator which offers programmability of start up time, switching frequency and current limit while operating in wide input and output voltage range. The switching frequency is programmable from 250kHz to 1.5MHz for an optimum solution. It also features important protection functions, such as Pre-Bias startup, hiccup current limit and thermal shutdown to give required system level security in the event of fault conditions. Applications • • • • Server Applications Storage Applications Embedded Telecom Systems Distributed Point of Load Power Architectures • • • Netcom Applications Computing Peripheral Voltage Regulators General DC-DC Converters Fig. 1. Typical application diagram Rev 9.0 1 PD-97506 IR3856WMPbF ABSOLUTE MAXIMUM RATINGS (Voltages referenced to GND unless otherwise specified) • Vin ……………………………………….……………. -0.3V to 25V • PVcc, Vcc ……………….……..….……..……….…… -0.3V to 8V (Note2) • Boot ……………………………………..……….…. -0.3V to 33V • SW …………………………………………..……… -0.3V to 25V(DC), -4V to 25V(AC, 100ns) • Boot to SW • OCSet • Input / output Pins • PGND to GND ……………...………………………….. -0.3V to +0.3V • Storage Temperature Range ................................... -55°C To 150°C • Junction Temperature Range ................................... -40°C To 150°C (Note2) • ESD Classification …………………………… ……… JEDEC Class 1C • Moisture sensitivity level………………...………………JEDEC Level 3@260 °C (Note5) ……..…………………………….…..….. -0.3V to Vcc+0.3V (Note1) ………………………………………….……. -0.3V to 30V (Max 30mA) ……………………………….. ... -0.3V to Vcc+0.3V (Note1) Note1: Must not exceed 8V Note2: Vcc must not exceed 7.5V for Junction Temperature between -10oC and -40oC Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications are not implied. PACKAGE INFORMATION 4mm x 5mm POWER QFN 13 12 VIN SW θ JA( Sync _ FET ) = 45 o C / W * θ JA( Ctrl _ FET ) = 45 o C / W * 11 θ J -PCB = 2 o C / W PGnd Exposed pads on underside are connected to copper pads of 4-layer (2 oz.) PCB board design * Boot 14 Enable 15 Seq 16 1 Fb 17 Gnd 2 3 4 5 6 10 PVcc 9 VCC 8 PGood 7 NC COMP Gnd Rt SS/SD OCSet ORDERING INFORMATION Rev 9.0 PACKAGE DESIGNATOR PACKAGE DESCRIPTION PIN COUNT PARTS PER REEL M IR3856WMTRPbF 17 4000 M IR3856WMTR1PbF 17 750 2 PD-97506 IR3856WMPbF Block Diagram Fig. 2. Simplified block diagram of the IR3856W Rev 9.0 3 PD-97506 IR3856WMPbF Pin Description Pin Name Description 1 Fb 2 NC Inverting input to the error amplifier. This pin is connected directly to the output of the regulator via resistor divider to set the output voltage and provide feedback to the error amplifier. No connect 3 Comp 4 Gnd 5 Rt Set the switching frequency. Connect an external resistor from this pin to Gnd to set the switching frequency. 6 SS/SD 7 OCSet Soft start / shutdown. This pin provides user programmable soft-start function. Connect an external capacitor from this pin to Gnd to set the start up time of the output voltage. The converter can be shutdown by pulling this pin below 0.3V. Current limit set point. A resistor from this pin to SW pin will set the current limit threshold. 8 PGood 9 VCC 10 PVcc This pin powers the drivers. A minimum of 1uF high frequency capacitor must be connected from this pin to the power ground (PGnd). 11 PGnd Power Ground. This pin serves as a separated ground for the MOSFET drivers and should be connected to the system’s power ground plane. 12 SW Switch node. This pin is connected to the output inductor. 13 VIN Input voltage connection pin. 14 Boot 15 Enable 16 Seq 17 Gnd Rev 9.0 Output of error amplifier. An external resistor and capacitor network is typically connected from this pin to Fb pin to provide loop compensation. Signal ground for internal reference and control circuitry. Power Good status pin. Output is open drain. Connect a pull up resistor from this pin to Vcc. This pin powers the internal IC. A minimum of 1uF high frequency capacitor must be connected from this pin to Analog ground (AGnd). Supply voltage for high side driver. A 0.1uF capacitor must be connected from this pin to SW. Enable pin to turn on and off the device. Use two external resistors to set the turn on threshold (see Enable section). Connect this pin to Vcc if it is not used. Sequence pin. Use two external resistors to set Simultaneous Power up sequencing. If this pin is not used connect to Vcc. Signal ground for internal reference and control circuitry. 4 PD-97506 IR3856WMPbF Recommended Operating Conditions Symbol Vin P Vcc, Vcc Boot to SW Vo Io Fs Tj Definition Input Voltage Supply Voltage Supply Voltage Output Voltage Output Current Switching Frequency Junction Temperature Min Max 1.5 4.5 4.5 0.7 0 225 -40 16 5.5 5.5 0.9*Vin 6 1650 125 Units V A kHz o C Electrical Specifications Unless otherwise specified, these specification apply over 4.5V< PVcc=Vcc<5.5V, Vin=12V 0oC<Tj< 125oC. Typical values are specified at Ta = 25oC. Parameter Symbol Test Condition Min TYP MAX Units Power Loss Power Loss P loss Vcc=5V, Vin=12V, V o=1.8V, I o=6A, Fs=600kHz, L=0.82uH, Note4 1.3 W MOSFET Rds(on) Top Switch R ds(on)_Top Bottom Switch Rds(on)_Bot o V Boot -Vsw =5V, ID =6A, Tj= 25 C o V cc =5V, ID =6A, Tj= 25 C 22.6 29.0 14.3 19 mΩ Reference Voltage Feedback Voltage VFB 0.7 o Accuracy o 0 C<Tj<125 C V -1.0 +1.0 +2.0 +2.0 % o o -40 C<Tj<125 C, Note3 Supply Current VCC Supply Current (Standby) Vcc Supply Current (Dyn) PVCC Supply Current (Standby) I CC(Standby) SS=0V, No Switching, Enable low ICC(Dyn) SS=3V, Vcc=5V, Fs=500kHz Enable high SS=0V, No Switching, Enable low 3 SS=3V, PVcc=5V, Fs=500kHz Enable high 7 IPCC(Standby) PVcc Supply Current (Dyn) I PCC(Dyn) 500 μA mA 6 μA mA Under Voltage Lockout VCC-Start-Threshold VCC_UVLO_Start Vcc Rising Trip Level 3.95 4.15 4.35 VCC-Stop-Threshold VCC_UVLO_Stop Vcc Falling Trip Level 3.65 3.85 4.05 Enable-Start-Threshold Enable_UVLO_Start Supply ramping up 1.14 1.2 1.36 Enable-Stop-Threshold Enable_UVLO_Stop Supply ramping down 0.9 1.0 1.06 Enable leakage current Ien Enable=3.3V Rev 9.0 15 V μA 5 PD-97506 IR3856WMPbF Electrical Specifications (continued) Unless otherwise specified, these specifications apply over 4.5V< PVcc=Vcc<5.5V, Vin=12V 0oC<Tj< 125oC. Typical values are specified at Ta = 25oC. Parameter Symbol Test Condition Min TYP MAX Units 0.665 0.7 0.735 V Rt=59K 225 250 275 Rt=28.7K 450 500 550 Rt=9.31K, Note4 1350 1500 1650 Oscillator Rt Voltage Frequency FS kHz Vramp Note4 1.8 Vp-p Ramp Offset Ramp (os) Note4 0.6 V Min Pulse Width Dmin(ctrl) Note4 50 Note4 130 Ramp Amplitude Fixed Off Time Max Duty Cycle Dmax Fs=250kHz 92 Vos Vfb-Vseq, Vseq=0.8V -10 200 ns % Error Amplifier Input Offset Voltage 0 +10 Input Bias Current IFb(E/A) -1 +1 Input Bias Current IVp(E/A) -1 +1 Isink(E/A) 0.40 0.85 1.2 Isource(E/A) 8 10 13 Sink Current Source Current Slew Rate Gain-Bandwidth Product DC Gain mV μA mA SR Note4 7 12 20 V/μs GBWP Note4 20 30 40 MHz Gain Note4 100 110 120 dB Vcc=4.5V 3.4 3.5 3.75 V 120 220 mV 1 V μA Maximum Voltage Vmax(E/A) Minimum Voltage Vmin(E/A) Note4 Common Mode Voltage 0 Soft Start/SD Soft Start Current Soft Start Clamp Voltage Shutdown Output Threshold ISS Source Vss(clamp) 14 20 26 2.7 3.0 3.3 SD 0.3 V Over Current Protection OCSET Current OC Comp Offset Voltage SS off time IOCSET VOFFSET Fs=250kHz 20.8 23.6 26.4 Fs=500kHz 43 48.8 54.6 Fs=1500kHz 136 154 172 Note4 -10 0 +10 SS_Hiccup 4096 μA mV Cycles Bootstrap Diode Forward Voltage I(Boot)=30mA Deadband time Note4 Rev 9.0 180 260 470 mV 5 10 30 ns 6 PD-97506 IR3856WMPbF Electrical Specifications Unless otherwise specified, these specifications apply over 4.5V< PVcc=Vcc<5.5V, Vin=12V 0oC<Tj< 125oC. Typical values are specified at Ta = 25oC. Parameter SYM Test Condition Min TYP MAX Units Thermal Shutdown Thermal Shutdown Note4 140 Hysteresis Note4 20 o C Power Good Power Good upper Threshold Upper Threshold Delay Power Good lower Threshold Lower Threshold Delay Delay Comparator Threshold Delay Comparator Hysteresis PGood Voltage Low Leakage Current VPG(upper) Fb Rising VPG(upper)_Dly Fb Rising VPG(lower) Fb Falling VPG(lower)_Dly Fb Falling PG(Delay) Relative to charge voltage, SS rising Delay(hys) Note4 PG(voltage) IPGood=-5mA Ileakage 0.770 0.810 0.840 256/Fs 0.560 0.6 V s 0.630 256/Fs V s 2 2.1 2.3 V 260 300 340 mV 0 0.5 V 10 μA Switch Node SW Bias Current SW=0V, Enable=0V Isw SW=0V,Enable=high,SS=3V,Vseq=0V , Note4 6 μA Note3: Cold temperature performance is guaranteed via correlation using statistical quality control. Not tested in production. Note4: Guaranteed by Design but not tested in production. Note5: Upgrade to industrial/MSL2 level applies from date codes 1227 (marking explained on application note AN1132 page 2). Products with prior date code of 1227 are qualified with MSL3 for Consumer market. Rev 9.0 7 PD-97506 IR3856WMPbF TYPICAL OPERATING CHARACTERISTICS (-40oC - 125oC) Fs=500 kHz Icc(Dyn) Icc(Standby) 290 5 270 4 250 [mA] [uA] 230 210 3 190 2 170 150 -40 -20 0 20 40 Temp[oC] 60 80 100 1 120 -40 -20 0 80 100 120 80 100 120 80 100 120 80 100 120 80 100 120 53 530 52 51 510 50 [uA] 520 500 490 49 48 47 480 46 470 45 460 44 450 43 -40 -20 0 20 40 60 80 100 120 -40 -20 0 20 o 40 60 o Temp[ C] Temp[ C] Vcc(UVLO) Start 4.35 4.05 4.30 4.00 4.25 3.95 4.20 3.90 [V] [V] 60 54 540 4.15 Vcc(UVLO) Stop 3.85 4.10 3.80 4.05 3.75 4.00 3.70 3.95 3.65 -40 -20 0 20 40 60 Temp[oC] 80 100 120 -40 -20 0 20 40 60 Temp[oC] Enable(UVLO) Start 1.36 Enable(UVLO) Stop 1.06 1.34 1.04 1.32 1.30 1.02 1.28 1.00 1.26 [V] [V] 40 Temp[oC] IOCSET(500kHz) FREQUENCY 550 [kHz] 20 1.24 0.98 1.22 0.96 1.20 0.94 1.18 0.92 1.16 1.14 0.90 -40 -20 0 20 40 o 60 80 100 120 -40 Temp[ C] -20 0 20 40 60 Temp[oC] Vfb ISS 26.0 711 24.0 706 [mV] [uA] 22.0 20.0 701 18.0 696 16.0 691 14.0 -40 -20 0 20 40 60 o Temp [ C] Rev 9.0 80 100 120 686 -40 -20 0 20 40 60 Temp[oC] 8 PD-97506 IR3856WMPbF TYPICAL OPERATING CHARACTERISTICS (-40oC - 125oC) Fs=500 kHz Ipcc(Standby) Ipcc(Dyn) 2.0 8.0 1.8 7.5 1.6 1.4 7.0 [mA] [uA] 1.2 1.0 0.8 6.5 6.0 0.6 0.4 5.5 0.2 0.0 5.0 -40 -20 0 20 40 60 80 100 120 -40 -20 0 o 20 40 60 80 100 120 o Temp[ C] Temp[ C] Rdson of MOSFETs Over Temperature at Vcc=5V 30 28 Resistance [mΩ] 26 24 22 20 18 16 14 12 -40 -20 0 20 40 60 80 100 120 140 Temperature [°C] Sync-FET Rev 9.0 Ctrl-FET 9 PD-97506 IR3856WMPbF Typical Efficiency and Power Loss Curves Vin=12V, Vcc=5V, Io=1A-6A, Fs=600kHz, Room Temperature, No Air Flow The table below shows the inductors used for each of the output voltages in the efficiency measurement. Vo (V) 0.9 1.0 1.1 1.2 1.5 1.8 2.5 3.3 5.0 L (uH) 0.68 0.68 0.82 0.82 1.0 1.0 1.5 1.5 2.2 P/N PCMB065T-R68MS PCMB065T-R68MS IHLP2525EZERR82M IHLP2525EZERR82M SPM6550T-1R0M100A SPM6550T-1R0M100A PCMB065T-1R5MS PCMB065T-1R5MS PCMB065T-2R2MS DCR (mOhm) 3.9 3.9 4.6 4.6 4.7 4.7 6.7 6.7 11.2 96 Efficiency (%) 94 92 90 88 86 84 82 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 Load Current (A) 0.9V 1.0V 1.1V 1.2V 2.0 2.5 3.0 1.5V 1.8V 2.5V 3.3V 5.0V 1.9 1.7 Power Loss (W) 1.5 1.3 1.1 0.9 0.7 0.5 0.3 0.1 1.0 1.5 3.5 4.0 4.5 5.0 5.5 6.0 Load Current (A) 0.9V Rev 9.0 1.0V 1.1V 1.2V 1.5V 1.8V 2.5V 3.3V 5.0V 10 PD-97506 IR3856WMPbF Typical Efficiency and Power Loss Curves Vin=5V, Vcc=5V, Io=1A-6A, Fs=600kHz, Room Temperature, No Air Flow The table below shows the inductors used for each of the output voltages in the efficiency measurement. Vo (V) 0.7 0.75 0.9 1.0 1.1 1.2 1.5 1.8 2.5 3.3 L (uH) 0.56 0.56 0.56 0.56 0.68 0.68 0.68 0.82 0.82 0.82 P/N IHLP2525EZERR56M IHLP2525EZERR56M IHLP2525EZERR56M IHLP2525EZERR56M PCMB065T-R68MS PCMB065T-R68MS PCMB065T-R68MS IHLP2525EZERR82M IHLP2525EZERR82M IHLP2525EZERR82M DCR (mOhm) 3.4 3.4 3.4 3.4 3.9 3.9 3.9 4.6 4.6 4.6 96 Efficiency (%) 94 92 90 88 86 84 82 80 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 Load Current (A) 0.7V 0.75V 0.9V 1.0V 1.1V 1.2V 1.5V 1.8V 2.5V 3.3V 1.3 Power Loss (W) 1.1 0.9 0.7 0.5 0.3 0.1 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 Load Current (A) 0.7Vout 1.2Vout Rev 9.0 0.75Vout 1.5Vout 0.9Vout 1.8Vout 1.0Vout 2.5Vout 1.1Vout 3.3Vout 11 PD-97506 IR3856WMPbF Circuit Description THEORY OF OPERATION Introduction The IR3856W uses a PWM voltage mode control scheme with external compensation to provide good noise immunity and maximum flexibility in selecting inductor values and capacitor types. The switching frequency is programmable from 250kHz to 1.2MHz and provides the capability of optimizing the design in terms of size and performance. IR3856W provides precisely regulated output voltage programmed via two external resistors from 0.7V to 0.9*Vin. If the input to the Enable pin is derived from the bus voltage by a suitably programmed resistive divider, it can be ensured that the IR3856W does not turn on until the bus voltage reaches the desired level. Only after the bus voltage reaches or exceeds this level will the voltage at Enable pin exceed its threshold, thus enabling the IR3856W. Therefore, in addition to being a logic input pin to enable the IR3856W, the Enable feature, with its precise threshold, also allows the user to implement an Under-Voltage Lockout for the bus voltage Vin. This is desirable particularly for high output voltage applications, where we might want the IR3856W to be disabled at least until Vin exceeds the desired output voltage level. The IR3856W operates with an external bias supply from 4.5V to 5.5V, allowing an extended operating input voltage range from 1.5V to 21V. The device utilizes the on-resistance of the low side MOSFET as current sense element, this method enhances the converter’s efficiency and reduces cost by eliminating the need for external current sense resistor. IR3856W includes two low Rds(on) MOSFETs using IR’s HEXFET technology. These are specifically designed for high efficiency applications. Under-Voltage Lockout and POR The under-voltage lockout circuit monitors the input supply Vcc and the Enable input. It assures that the MOSFET driver outputs remain in the off state whenever either of these two signals drop below the set thresholds. Normal operation resumes once Vcc and Enable rise above their thresholds. Fig. 3a. Normal Start up, Device turns on when the Bus voltage reaches 10.2V Figure 3b. shows the recommended start-up sequence for the non-sequenced operation of IR3856W. The POR (Power On Ready) signal is generated when all these signals reach the valid logic level (see system block diagram). When the POR is asserted the soft start sequence starts (see soft start section). Enable The Enable features another level of flexibility for start up. The Enable has precise threshold which is internally monitored by Under-Voltage Lockout (UVLO) circuit. Therefore, the IR3856W will turn on only when the voltage at the Enable pin exceeds this threshold, typically, 1.2V. Rev 9.0 Fig. 3b. Recommended startup sequence, Non-Sequenced operation Figure 3c. shows the recommended startup sequence for sequenced operation of IR3856W 12 PD-97506 IR3856WMPbF Fig. 5. Pre-Bias startup pulses Soft-Start Fig. 3c. Recommended startup sequence, Sequenced operation Pre-Bias Startup IR3856W is able to start up into pre-charged output, which prevents oscillation and disturbances of the output voltage. The IR3856W has a programmable soft-start to control the output voltage rise and to limit the current surge at the start-up. To ensure correct start-up, the soft-start sequence initiates when the Enable and Vcc rise above their UVLO thresholds and generate the Power On Ready (POR) signal. The internal current source (typically 20uA) charges the external capacitor Css linearly from 0V to 3V. Figure 6 shows the waveforms during the soft start. The output starts in asynchronous fashion and keeps the synchronous MOSFET off until the first gate signal for control MOSFET is generated. Figure 4 shows a typical Pre-Bias condition at start up. The start up time can be estimated by: The synchronous MOSFET always starts with a narrow pulse width and gradually increases its duty cycle with a step of 25%, 50%, 75% and 100% until it reaches the steady state value. The number of these startup pulses for the synchronous MOSFET is internally programmed. Figure 5 shows a series of 32, 16, 8 startup pulses. During the soft start the OCP is enabled to protect the device for any short circuit and over current condition. Fig. 4. Pre-Bias startup Rev 9.0 Tstart = (1.4 - 0.7) * CSS 20μA - - - - - - - - - - - - - - - - - - - - (1) Fig. 6. Theoretical operation waveforms during soft-start 13 PD-97506 IR3856WMPbF Operating Frequency The switching frequency can be programmed between 250kHz – 1200kHz by connecting an external resistor from Rt pin to Gnd. Table 1 tabulates the oscillator frequency versus Rt. Table 1. Switching Frequency and IOCSet vs. External Resistor (Rt) Rt (kΩ) Fs (kHz) Iocset (μA) 47.5 300 29.4 35.7 400 39.2 28.7 500 48.7 23.7 600 59.07 20.5 700 68.2 17.8 800 78.6 15.8 900 88.6 14.3 1000 97.9 12.7 1100 110.2 11.5 1200 121.7 Shutdown The IR3856W can be shutdown by pulling the Enable pin below its 1 V threshold. This will tristate both, the high side driver as well as the low side driver. Alternatively, the output can be shutdown by pulling the soft-start pin below 0.3V. Normal operation is resumed by cycling the voltage at the Soft Start pin. Over-Current Protection The over current protection is performed by sensing current through the RDS(on) of low side MOSFET. This method enhances the converter’s efficiency and reduces cost by eliminating a current sense resistor. As shown in figure 7, an external resistor (ROCSet) is connected between OCSet pin and the switch node (SW) which sets the current limit set point. An internal current source sources current (IOCSet ) out of the OCSet pin. This current is a function of the switching frequency and hence, of Rt. Rev 9.0 I OCSet (μA ) = 1400 .......... .......... ...............( 2) R t (kΩ) Table 1. shows IOCSet at different switching frequencies. The internal current source develops a voltage across ROCSet. When the low side MOSFET is turned on, the inductor current flows through the Q2 and results in a voltage at OCSet which is given by: VOCSet = ( IOCSet ∗ ROCSet ) − ( RDS(on) ∗ I L ) ...........(3) Fig. 7. Connection of over current sensing resistor An over current is detected if the OCSet pin goes below ground. Hence, at the current limit threshold, VOCset=0. Then, for a current limit setting ILimit, ROCSet is calculated as follows: ROCSet = R DS (on) * I Limit IOCSet ........................ (4) An overcurrent detection trips the OCP comparator, latches OCP signal and cycles the soft start function in hiccup mode. The hiccup is performed by shorting the soft-start capacitor to ground and counting the number of switching cycles. The Soft Start pin is held low until 4096 cycles have been completed. The OCP signal resets and the converter recovers. After every soft start cycle, the converter stays in this mode until the overload or short circuit is removed. The OCP circuit starts sampling current typically 160 ns after the low gate drive rises to about 3V. This delay functions to filter out switching noise. 14 PD-97506 IR3856WMPbF Thermal Shutdown Temperature sensing is provided inside IR3856W. The trip threshold is typically set to 140oC. When trip threshold is exceeded, thermal shutdown turns off both MOSFETs and discharges the soft start capacitor. 1.5V <Vin<16V 4.5V <Vcc<5.5V PVcc Enable Vin Boot Vo(master) Vcc SW PGood PGood Automatic restart is initiated when the sensed temperature drops within the operating range. There is a 20oC hysteresis in the thermal shutdown threshold. OCSet Seq RA Fb Rt RB SS/ SD Output Voltage Sequencing The IR3856W can accommodate user programmable sequencing using Seq, Enable and Power Good pins. Gnd PGnd Comp 1.5V <Vin<16V 4.5V <Vcc<5.5V PVcc Vcc Vo(master) Enable Vin Boot Vo(slave) SW PGood Vo1 RE PGood OCSet Seq Vo2 RF Fb Rt SS/ SD RC RD Gnd PGnd Comp Simultaneous Powerup Fig. 8a. Simultaneous Power-up of the slave with respect to the master. Through these pins, voltage sequencing such as simultaneous and sequential can be implemented. Figure 8. shows simultaneous sequencing configurations. In simultaneous power-up, the voltage at the Seq pin of the slave reaches 0.7V before the Fb pin of the master. For RE/RF =RC/RD, therefore, the output voltage of the slave follows that of the master until the voltage at the Seq pin of the slave reaches 0.7 V. After the voltage at the Seq pin of the slave exceeds 0.85V, the internal 0.7V reference of the slave dictates its output voltage. It is recommended that irrespective of the sequencing configuration used, the input voltage should be allowed to come up to its nominal value first, followed by Vcc and Enable, before the sequencing signal is applied. For non-sequenced operation, the Seq pin should be tied to a voltage greater than 0.85V, such as 3.3V or Vcc. Again, the input voltage should be allowed to come up before Vcc and Enable. Rev 9.0 Fig. 8b. Application Circuit for Simultaneous Sequencing Power Good Output The IC continually monitors the output voltage via Feedback (Fb pin). The feedback voltage forms an input to a window comparator whose upper and lower thresholds are 0.805V and 0.595V respectively. Hence, the Power Good signal is flagged when the Fb pin voltage is within the PGood window, i. e. between 0.595V to 0.805V, as shown in Fig .9. The PGood pin is open drain and it needs to be externally pulled high. High state indicates that output is in regulation. Fig. 9a shows the PGood timing diagram for nontracking operation. In this case, during startup, PGood goes high after the SS voltage reaches 2.1V if the Fb voltage is within the PGood comparator window. Fig. 9a. and Fig 9.b. also show a 256 cycle delay between the Fb voltage entering within the thresholds defined by the PGood window and PGood going high. 15 PD-97506 IR3856WMPbF TIMING DIAGRAM OF PGOOD FUNCTION Fig.9a IR3856W Non-Tracking Operation (Seq=Vcc) Fig.9b IR3856W Tracking Operation Rev 9.0 16 PD-97506 IR3856WMPbF Minimum on time Considerations Maximum Duty Ratio Considerations The minimum ON time is the shortest amount of time for which the Control FET may be reliably turned on, and this depends on the internal timing delays. For the IR3856W, the typical minimum on-time is specified as 50 ns. Any design or application using the IR3856W must ensure operation with a pulse width that is higher than this minimum on-time and preferably higher than 100 ns. This is necessary for the circuit to operate without jitter and pulseskipping, which can cause high inductor current ripple and high output voltage ripple. A fixed off-time of 200 ns maximum is specified for the IR3856W. This provides an upper limit on the operating duty ratio at any given switching frequency. It is clear that, higher the switching frequency, the lower is the maximum duty ratio at which the IR3856W can operate. To allow a margin of 50 ns, the maximum operating duty ratio in any application using the IR3856W should still accommodate about 250 ns off-time. Fig 10. shows a plot of the maximum duty ratio v/s the switching frequency, with 250 ns off-time. 95 D Fs Vout = Vin × Fs In any application that uses the IR3856W, the following condition must be satisfied: t on (min) ≤ t on ∴ t on (min) ≤ Vout t on(min) The minimum output voltage is limited by the reference voltage and hence Vout(min) = 0.7 V. Therefore, for Vout(min) = 0.7 V, ∴ Vin × Fs ≤ 85 80 75 Vout Vin × Fs ∴ Vin × Fs ≤ 90 Max Duty Cycle (%) t on = 70 300 400 500 600 700 800 900 1000 1100 1200 Switching Frequency (kHz) Fig. 10. Maximum duty cycle v/s switching frequency. Vout (min) ∴ Vin × Fs ≤ t on(min) 0.7 V = 7 × 10 6 V/s 100 ns Therefore, at the maximum recommended input voltage 21V and minimum output voltage, the converter should be designed at a switching frequency that does not exceed 330 kHz. Conversely, for operation at the maximum recommended operating frequency 1.2 MHz and minimum output voltage, any voltage above 5.83V may not be stepped down reliably without pulse-skipping. Rev 9.0 17 PD-97506 IR3856WMPbF when an external resistor divider is connected to the output as shown in figure 11. Equation (7) can be rewritten as: Application Information Design Example: The following example is a typical application for IR3856W. The application circuit is shown on page 24. Vin = 12 V ( 13.2V max) ⎛ V R9 = R8 ∗ ⎜⎜ ref ⎝ V o−Vref ⎞ ⎟ ..................................(8) ⎟ ⎠ For the calculated values of R8 feedback compensation section. Vo = 1.8 V Io = 6 A VOUT ΔVo ≤ 54mV IR3856W IR3624 Fs = 600 kHz R9 As explained earlier, the precise threshold of the Enable lends itself well to implementation of a UVLO for the Bus Voltage. V in IR3856W Enable R1 R2 For a typical Enable threshold of VEN = 1.2 V R2 = VEN = 1.2 .......... (5) R1 + R 2 VEN R 2 = R1 .......... (6) Vin( min ) − VEN For a Vin (min)=10.2V, R1=49.9K and R2=7.5K is a good choice. Programming the frequency For Fs = 600 kHz, select Rt = 23.7 kΩ, using Table. 1. Output Voltage Programming Output voltage is programmed by reference voltage and external voltage divider. The Fb pin is the inverting input of the error amplifier, which is internally referenced to 0.7V. The divider is ratioed to provide 0.7V at the Fb pin when the output is at its desired value. The output voltage is defined by using the following equation: ⎛ R ⎞ Vo = Vref ∗ ⎜⎜1 + 8 ⎟⎟ ...................................(7) ⎝ R9 ⎠ Rev 9.0 R8 Fb Enabling the IR3856W Vin(min) * and R9 see Fig. 11. Typical application of the IR3856W for programming the output voltage Soft-Start Programming The soft-start timing can be programmed by selecting the soft-start capacitance value. From (1), for a desired start-up time of the converter, the soft start capacitor can be calculated by using: C SS (μF) = Tstart ( ms ) × 0.02857 .......... (9) Where Tstart is the desired start-up time (ms). For a start-up time of 3.5ms, the soft-start capacitor will be 0.099μF. Choose a 0.1μF ceramic capacitor. Bootstrap Capacitor Selection To drive the Control FET, it is necessary to supply a gate voltage at least 4V greater than the voltage at the SW pin, which is connected the source of the Control FET . This is achieved by using a bootstrap configuration, which comprises the internal bootstrap diode and an external bootstrap capacitor (C6), as shown in Fig. 12. The operation of the circuit is as follows: When the lower MOSFET is turned on, the capacitor node connected to SW is pulled down to ground. The capacitor charges towards Vcc through the internal bootstrap diode, which has a forward voltage drop VD. The voltage Vc across the bootstrap capacitor C6 is approximately given as Vc ≅ Vcc − VD .......... .......... ...... (10) When the upper MOSFET turns on in the next cycle, the capacitor node connected to SW rises to the bus voltage Vin. However, if the value of C6 is appropriately chosen, 18 PD-97506 IR3856WMPbF the voltage Vc across C6 remains approximately unchanged and the voltage at the Boot pin becomes VBoot ≅ Vin + Vcc − VD ........................................ (11) Fig. 12. Bootstrap circuit to generate Vc voltage A bootstrap capacitor of value 0.1uF is suitable for most applications. For applications with 21V input voltage, the switch node may ring above the 25V absolute maximum voltage rating. To prevent this, in addition to using best layout practices, it may be necessary to provide a 10ohm resistor in series with the boot capacitor. advisable to have 2x10uF 25V ceramic capacitors C3216X5R1E106M from TDK. In addition to these, although not mandatory, a 1X330uF, 25V SMD capacitor EEV-FK1E331P may also be used as a bulk capacitor and is recommended if the input power supply is not located close to the converter. Inductor Selection The inductor is selected based on output power, operating frequency and efficiency requirements. A low inductor value causes large ripple current, resulting in the smaller size, faster response to a load transient but poor efficiency and high output noise. Generally, the selection of the inductor value can be reduced to the desired maximum ripple current in the inductor (Δi ). The optimum point is usually found between 20% and 50% ripple of the output current. For the buck converter, the inductor value for the desired operating ripple current can be determined using the following relation: Δi 1 ; Δt = D ∗ Δt Fs .......... .......... .......... . (14) Vo L = (Vin − Vo ) ∗ Vin ∗ Δi * Fs Vin − Vo = L ∗ Where: Input Capacitor Selection The ripple current generated during the on time of the upper MOSFET should be provided by the input capacitor. The RMS value of this ripple is expressed by: Vin = Maximum input voltage Vo = Output Voltage Δi = Inductor ripple current F s = Switching frequency Δt = Turn on time D = Duty cycle IRMS = Io ∗ D ∗ (1 − D) ........................(12) D= Vo ................................ (13) Vin If Δi ≈ 42%(Io), then the output inductor is calculated to be 1.01μH. Select L=1 μH. The SPM6550T-1R0M from TDK provides a compact inductor suitable for this application Where: D is the Duty Cycle IRMS is the RMS value of the input capacitor current. Io is the output current. For Io=6A and D = 0.15, the IRMS = 2.14 A. Ceramic capacitors are recommended due to their peak current capabilities. They also feature low ESR and ESL at higher frequency which enables better efficiency. For this application, it is Rev 9.0 19 PD-97506 IR3856WMPbF Output Capacitor Selection The voltage ripple and transient requirements determine the output capacitors type and values. The criteria is normally based on the value of the Effective Series Resistance (ESR). However the actual capacitance value and the Equivalent Series Inductance (ESL) are other contributing components. These components can be described as ΔVo = ΔVo( ESR ) + ΔVo( ESL ) + ΔVo(C ) ΔVo(C ) = ⎞ ⎟⎟ * ESL ⎠ voltage ΔI L = Inductor ripple 2 ∗ π Lo ∗ Co ................................ (16) Phase Gain 0 dB 00 -40dB/decade ripple current Since the output capacitor has a major role in the overall performance of the converter and determines the result of transient response, selection of the capacitor is critical. The IR3856W can perform well with all types of capacitors. As a rule, the capacitor must have low enough ESR to meet output ripple and load transient requirements. The goal for this design is to meet the voltage ripple requirement in the smallest possible capacitor size. Therefore it is advisable to select ceramic capacitors due to their low ESR and ESL and small size. Four of the Panasonic ECJ2FB0J226ML (22uF, 6.3V, 3mOhm) capacitors is a good choice. Feedback Compensation The IR3856W is a voltage mode controller. The control loop is a single voltage feedback path including error amplifier and error comparator. To achieve fast transient response and accurate output regulation, a compensation circuit is necessary. The goal of the compensation network is to provide a closed-loop transfer function with the highest 0 dB crossing frequency and adequate phase margin (greater than 45o). Rev 9.0 1 .......... .......... ..... (15) ΔI L 8 * C o * Fs ΔVo = Output FLC = Figure 13 shows gain and phase of the LC filter. Since we already have 180o phase shift from the output filter alone, the system runs the risk of being unstable. ΔVo( ESR ) = ΔI L * ESR ⎛ V − Vo ΔVo( ESL ) = ⎜⎜ in L ⎝ The output LC filter introduces a double pole, –40dB/decade gain slope above its corner resonant frequency, and a total phase lag of 180o (see figure 13). The resonant frequency of the LC filter is expressed as follows: -1800 FLC Frequency FLC Frequency Fig. 13. Gain and Phase of LC filter The IR3856W uses a voltage-type error amplifier with high-gain (110dB) and wide-bandwidth. The output of the amplifier is available for DC gain control and AC phase compensation. The error amplifier can be compensated either in type II or type III compensation. Local feedback with Type II compensation is shown in Fig. 14. This method requires that the output capacitor should have enough ESR to satisfy stability requirements. In general the output capacitor’s ESR generates a zero typically at 5kHz to 50kHz which is essential for an acceptable phase margin. The ESR zero of the output capacitor is expressed as follows: FESR = 1 .......... .......... ....... (17) 2 ∗ π*ESR*C o 20 PD-97506 IR3856WMPbF VOUT Z IN C POLE R3 C4 R8 Zf Fb R9 Gain(dB) E/A Comp Ve Fz = 0.75* FZ F POLE Frequency Fig. 14. Type II compensation network and its asymptotic gain plot The transfer function (Ve/Vo) is given by: Ve 1 + sR3C4 Z = H(s) = − f = − .....(18) ZIN sR8C4 Vo The (s) indicates that the transfer function varies as a function of frequency. This configuration introduces a gain and zero, expressed by: Fz = To cancel one of the LC filter poles, place the zero before the LC filter resonant frequency pole: Fz = 75%FLC VREF H(s) dB H(s) = Where: Vin = Maximum Input Voltage Vosc = Oscillator Ramp Voltage Fo = Crossover Frequency FESR = Zero Frequency of the Output Capacitor FLC = Resonant Frequency of the Output Filter R8 = Feedback Resistor R3 ......................................(19) R8 1 ............................(20) 2π * R3 * C4 First select the desired zero-crossover frequency (Fo): Fo > FESR and Fo ≤ (1/5 ~ 1/10) * Fs Vosc * Fo * FESR * R8 2 Vin * FLC ...........................(21) FP = .....................................(22) 1 .................................(23) C *C 2π * R3 * 4 POLE C4 + CPOLE The pole sets to one half of the switching frequency which results in the capacitor CPOLE: CPOLE = 1 π*R3*Fs − 1 C4 ≅ 1 ......................(24) π*R3*Fs For a general solution for unconditional stability for any type of output capacitors, and a wide range of ESR values, we should implement local feedback with a type III compensation network. The typically used compensation network for voltage-mode controller is shown in figure 15. Again, the transfer function is given by: Ve Z = H(s) = − f Vo ZIN By replacing Zin and Zf according to figure 15, the transfer function can be expressed as: H(s) = − Rev 9.0 2π Lo * Co Use equations (20), (21) and (22) to calculate C4. One more capacitor is sometimes added in parallel with C4 and R3. This introduces one more pole which is mainly used to suppress the switching noise. The additional pole is given by: Use the following equation to calculate R3: R3 = 1 (1 + sR3C4 )[1 + sC7 (R8 + R10 )] ⎡ ⎛ C * C3 ⎞⎤ ⎟⎥(1 + sR10C7 ) sR8 (C4 + C3 )⎢1 + sR3 ⎜⎜ 4 ⎟ ⎢⎣ ⎝ C4 + C3 ⎠⎥⎦ 21 ....(25) PD-97506 IR3856WMPbF VOUT ZIN C3 C7 R3 R10 C4 R8 Zf Fb R9 Gain(dB) E/A Comp Ve FZ2 FP2 FP3 Frequency Fig.15. Type III Compensation network and its asymptotic gain plot The compensation network has three poles and two zeros and they are expressed as follows: FP1 = 0 ..................................................................(26) FP 2 = 1 ...............................................(27) 2π * R10 * C7 1 FP3 = FZ1 ≅ 1 ...............(28) 2π * R3 * C3 ⎛ C * C3 ⎞ ⎟ 2π * R3 ⎜⎜ 4 ⎟ ⎝ C4 + C3 ⎠ 1 = .............................................(29) 2π * R3 * C4 FZ 2 = 1 1 ≅ ..........(30) 2π * C7 * (R8 + R10 ) 2π * C7 * R8 Cross over frequency is expressed as: Fo = R3 * C7 * Vin 1 * ................................(31) Vosc 2π * Lo * Co Based on the frequency of the zero generated by the output capacitor and its ESR, relative to crossover frequency, the compensation type can be different. The table below shows the compensation types and location of the crossover frequency. Rev 9.0 FESR vs Fo Output Capacitor Type II FLC<FESR<Fo<Fs/2 Electrolytic Tantalum Type III FLC<Fo<FESR Tantalum Ceramic VREF H(s) dB FZ1 Compensator Type The higher the crossover frequency, the potentially faster the load transient response. However, the crossover frequency should be low enough to allow attenuation of switching noise. Typically, the control loop bandwidth or crossover frequency is selected such that Fo ≤ (1/5 ~ 1/10) * Fs The DC gain should be large enough to provide high DC-regulation accuracy. The phase margin should be greater than 45o for overall stability. For this design we have: Vin=12V Vo=1.8V Vosc=1.8V Vref=0.7V Lo=1 uH Co=4x22uF, ESR=3mOhm each It must be noted here that the value of the capacitance used in the compensator design must be the small signal value. For instance, the small signal capacitance of the 22uF capacitor used in this design is 12uF at 1.8 V DC bias and 600 kHz frequency. It is this value that must be used for all computations related to the compensation. The small signal value may be obtained from the manufacturer’s datasheets, design tools or SPICE models. Alternatively, they may also be inferred from measuring the power stage transfer function of the converter and measuring the double pole frequency FLC and using equation (16) to compute the small signal Co. These result to: FLC=22.97 kHz FESR=4.4 MHz Fs/2=300 kHz Select crossover frequency: Fo=100 kHz Since FLC<Fo<Fs/2<FESR, TypeIII is selected to place the pole and zeros. 22 PD-97506 IR3856WMPbF Detailed calculation of compensation Type-III o Desired Phase Margin Θ = 70 1− sin Θ = 17.63 kHz FZ2 = Fo 1+ sin Θ FP2 = Fo 1+ sin Θ = 567.1 kHz 1− sin Θ Select: FZ1 = 0.5* FZ2 = 8.82 kHz and FP3 = 0.5* Fs = 300 kHz Select: C7 = 2.2nF Calculate R3, C3 and C4 : R3 = 2π * Fo * Lo * Co * Vosc ; R3 = 2.56 kΩ C7 * Vin Select: R3 = 2.55 kΩ 1 C4 = ;C4 = 8.84 nF, Select: C4 = 10 nF 2π * FZ1* R3 C3 = 1 ; C3 = 258.79pF, Select:C3 = 220 pF 2π * FP3 * R3 Calculate R10, R8 and R9 : R10 = R8 = 1 ; R10 = 128 Ω, Select: R10 = 130 Ω 2π * C7 * FP2 1 - R10; R8 = 3.97 kΩ, 2π * C7 * FZ2 Programming the Current-Limit The Current-Limit threshold can be set by connecting a resistor (ROCSET) from the SW pin to the OCSet pin. The resistor can be calculated by using equation (4). This resistor ROCSET must be placed close to the IC. The RDS(on) has a positive temperature coefficient and it should be considered for the worst case operation. ISET = IL (critical) = ROCSet∗ IOCSet .......................(32) RDS(on) RDS(on) = 14.3 mΩ * 1.25 = 17.875 mΩ ISET ≅ I o(LIM) = 6 A *1.5 = 9 A (50% over nominal output current ) IOCSet = 59.07 μA (at Fs = 600kHz) ROCSet = 2.694 kΩ Select R7 = 2.67 kΩ Setting the Power Good Threshold Power Good threshold is internally set at 88% of Vref. When the voltage at the FB pin exceeds the threshold, PGood is asserted. The PGood is an open drain output. Hence, it is necessary to use a pull up resistor RPG from PGood pin to Vcc. The value of the pull-up resistor must be chosen such as to limit the current flowing into the PGood pin, when the output voltage is not in regulation, to less than 5mA. A typical value used is 10kΩ. Select: R8 = 4.02 kΩ R9 = Vref * R8 ; R9 = 2.57 kΩ Select: R9 = 2.55 kΩ Vo -Vref Rev 9.0 23 PD-97506 IR3856WMPbF Application Diagram: Fig. 16. Application circuit diagram for a 12V to 1.8 V, 6 A Point Of Load Converter Suggested Bill of Materials for the application circuit: Part Reference Cin Lo Co R1 R2 Rt Rocset RPG Css C6 R3 C3 C4 R8 R9 R10 C7 CVcc CPVcc U1 Rev 9.0 Quantity 1 2 1 1 4 1 1 1 1 1 2 1 1 1 1 1 1 1 2 1 Value 330uF 10uF 0.1uF 1.0uH 22uF 49.9k 7.5k 23.7k 2.67k 10k 0.1uF 2.05k 220pF 10nF 4.02k 2.55k 130 2200pF 1.0uF IR3856W Description SMD Elecrolytic, Fsize, 25V, 20% 1206, 16V, X5R, 20% 0603, 25V, X7R, 10% 6.9x6.5x5mm, 20%, 4.7mOhm 0805, 6.3V, X5R, 20% Thick Film, 0603,1/10 W,1% Thick Film, 0603,1/10W,1% Thick Film, 0603,1/10W,1% Thick Film, 0603,1/10W,1% Thick Film, 0603,1/10W,1% 0603, 25V, X7R, 10% Thick Film, 0603,1/10W,1% 50V, 0603, NPO, 5% 0603, 50V, X7R, 10% Thick Film, 0603,1/10W,1% Thick Film, 0603,1/10W,1% Thick Film, 0603,1/10W,1% 0603, 50V, X7R, 10% 0603, 16V, X5R, 20% SupIRBuck, 6A, PQFN 4x5mm Manufacturer Panasonic TDK Panasonic TDK Panasonic Rohm Rohm Rohm Rohm Rohm Panasonic Rohm Panasonic Panasonic Rohm Rohm Rohm Panasonic Panasonic International Rectifier Part Number EEV-FK1E331P C3216X5R1E106M ECJ-1VB1E104K SPM6550T-1R0M100A ECJ-2FB0J226ML MCR03EZPFX4992 MCR03EZPFX7501 MCR03EZPFX2372 MCR03EZPFX2671 MCR03EZPFX1002 ECJ-1VB1E104K MCR03EZPFX2051 ECJ-1VC1H221J ECJ-1VB1H103K MCR03EZPFX4021 MCR03EZPFX2551 ERJ-3EKF1300V ECJ-1VB1H222K ECJ-BVB1C105M IR3856WMPbF 24 PD-97506 IR3856WMPbF TYPICAL OPERATING WAVEFORMS Vin=12.0V, Vcc=5V, Vo=1.8V, Io=0-6A, Room Temperature, No Air Flow Fig. 17. Start up at 6A Load Ch1:Vin, Ch2:Vo, Ch3:Vss, Ch4:Enable Fig. 18. Start up at 6A Load, Ch1:Vin, Ch2:Vo, Ch3:Vss, Ch4:VPGood Fig. 19. Start up with 1.62V Pre Bias, 0A Load, Ch2:Vo, Ch3:VSS Fig. 20. Output Voltage Ripple, 6A load Ch3: Vo Fig. 21. Inductor node at 6A load Ch3:LX Fig. 22. Short (Hiccup) Recovery Ch2:Vo , Ch3:VSS Rev 9.0 25 PD-97506 IR3856WMPbF TYPICAL OPERATING WAVEFORMS Vin=12V, Vcc=5V, Vo=1.8V, Io=3A-6A, Room Temperature, No Air Flow Fig. 23. Transient Response, 3A to 6A step 2.5A/μs Ch3:Vo, Ch4:Io Rev 9.0 26 PD-97506 IR3856WMPbF TYPICAL OPERATING WAVEFORMS Vin=12V, Vcc=5V, Vo=1.8V, Io=6A, Room Temperature, No Air Flow Fig. 24. Bode Plot at 6A load shows a bandwidth of 104kHz and phase margin of 54 degrees Rev 9.0 27 PD-97506 IR3856WMPbF Simultaneous Tracking at Power Up and Power Down Vin=12V, Vo=1.8V, Io=6A, Room Temperature, No Air Flow VOUT 3.3V 4.02K R s1 2..55K Rs2 IR3856W IR3624 Seq R8 4.02K Fb R9 2.55K Fig. 25: Simultaneous Tracking a 3.3V input at power-up and shut-down with 6A load. Ch2: Vo2 (1.8Vout) Ch3:SS(1.8V) Ch4: Vo1 (3.3V) Rev 9.0 28 PD-97506 IR3856WMPbF Layout Considerations The layout is very important when designing high frequency switching converters. Layout will affect noise pickup and can cause a good design to perform with less than expected results. Make all the connections for the power components in the top layer with wide, copper filled areas or polygons. In general, it is desirable to make proper use of power planes and polygons for power distribution and heat dissipation. The inductor, output capacitors and the IR3856W should be as close to each other as possible. This helps to reduce the EMI radiated by the power traces due to the high switching currents through them. Place the input capacitor directly at the Vin pin of IR3856W. The feedback part of the system should be kept away from the inductor and other noise sources. The critical bypass components such as capacitors for Vcc should be close to their respective pins. It is important to place the feedback components including feedback resistors and compensation components close to Fb and Comp pins. The connection between the OCSet resistor and the Sw pin should not share any trace with the connection between the bootstrap capacitor and the Sw pin. Instead, it is recommended to use a Kelvin connection of the trace from the OCSet resistor and the trace from the bootstrap Vin capacitor at the Sw pin. PGnd In a multilayer PCB use one layer as a power ground plane and have a control circuit ground (analog ground), to which all signals are referenced. The goal is to localize the high current path to a separate loop that does not Vout interfere with the more sensitive analog control AGnd function. These two grounds must be connected together on the PC board layout at a single point. The Power QFN is a thermally enhanced package. Based on thermal performance it is recommended to use at least a 4-layers PCB. To effectively remove heat from the device the exposed pad should be connected to the ground plane using vias. Figure 26 illustrates the implementation of the layout guidelines outlined above, on the IRDC3856W 4 layer demoboard. Vin PGnd Vout AGnd Compensation parts should be placed as close as possible to the Comp pin. Vout Vin All bypass caps should be placed as close as possible to their connecting pins. AGnd Vin Resistors Rt, Rocset, and SS capacitor should be placed as close as possible to their pins. PGnd Fig. 26a. IRDC3856W demo-board layout considerations – Top Layer Rev 9.0 29 PD-97506 IR3856WMPbF PGnd Fig. 26b. IRDC3856 demoboard layout considerations – Bottom Layer Analog Ground plane Vin Single point connection between AGND & PGND, should be close to the SupIRBuck, kept away from noise sources. Power Ground Plane AGnd Fig. 26c. IRDC3856 demoboard layout considerations – Mid Layer 1 Feedback trace should be kept away form noise sources Fig. 26d. IRDC3856 demoboard layout considerations – Mid Layer 2 Rev 9.0 30 PD-97506 IR3856WMPbF PCB Metal and Components Placement Rev 9.0 31 PD-97506 IR3856WMPbF Solder Resist Rev 9.0 32 PD-97506 IR3856WMPbF Stencil Design Rev 9.0 33 PD-97506 IR3856WMPbF IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7903 This product has been designed and qualified for the Industrial market (Note5) Visit us at www.irf.com for sales contact information Data and specifications subject to change without notice. 08/12 Rev 9.0 34