KBPC8005 THRU KBPC810 SINGLE-PHASE 8.0AMPS. SILICON BRIDGE RECTIFIER KBPC FEATURE .Surge overload ratings 130 Amperes .Low forward voltage drop .296(7.5) .255(6.5) MECHANICAL DATA .052(1.3) DIA. .048(1.2) TYP. .Case: Molded plastic .Epoxy: UL 94V-0 rate flame retardant .Lead: MIL-STD- 202E, Method 208 guaranteed .Polarity: As marked .Mounting position: Any .Weight: 6.9grams .750 (19.1) .770(19.6) .730(18.5) .520(13.2) .480(12.2) MIN. HOLE FOR NO. 6 SCREW .770(19.6) .730(18.5) .520(13.2) .480(12.2) + ~~ - Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS (single-phase, half-wave, 60HZ, resistive or inductive load rating at 25°C, unless otherwise stated) SYM BOL Type Number Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC blocking Voltage Maximum Average Forward rectified Output Current at TA=50°C KBPC KBPC KBPC KBPC KBPC KBPC 8005 801 802 804 806 808 VRRM VRMS VDC KBPC 810 units 50 100 200 400 600 800 1000 V 35 70 140 280 420 560 700 V 50 100 200 400 600 800 1000 V IF(AV) 8.0 A IFSM 130 A VF 1.0 V 10.0 uA Peak Forward Surge Current 8.3ms single half sine-wave superimposed on rate load (JEDEC method) Maximum Forward Voltage Drop per element at 4.0A DC Maximum DC Reverse Current Ta =25°C at rated DC blocking voltage Ta =100°C 2 I t Rating for Fusing (t﹤8.3ms) Typical Junction Capacitance (Note 1) Typical Thermal Resistance (Note 2) Storage Temperature Operating Junction Temperature IR I2 t CJ R(JA) TSTG TJ 500.0 166 A Sec 200 pF 36 °C /W -55 to +150 °C -55 to +125 °C Note: 1. Measured at 1.0 MHz and applied reverse voltage of 4.0Vdc 2.Thermal Resistance from Junction to lead mounted on on P.C.B. with 0.5×0.5”(13×13mm) copper pads. - 73 - uA 2 RATING AND CHARACTERISTIC CURVES (KBPC8005 THRU KBPC810) FIG.1-TYPICAL FORWARD CURRENT DERATING CURVE FIG.2-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 8.0 INSTANEOUS FORWARD CURRENT,(A) AVERGE FORWARD RECTIFIED CURRENT,(A) 100 4.0 Single Phase Half Wave 60Hz Resistive or inductive Load 0 0 50 100 150 10 1.0 .1 200 TJ=25℃ Pulse Width=300μs 1% Duty Cycle 1.0 .8 .6 AMBIENT TEMPERTURE,(℃) 1.2 1.4 INSTANEOUS FORWARD VOLTAGE,(V) FIG.4-TYPICAL REVERSE CHARACTERISTICS FIG.3-MAXIMUN NON-REPETITIVE FORWARD SURGE CURRENT 10 8.3ms Single Half Sine-Wave (JEDEC Method) 150 INSTANEOUS REVERSE CURRENT,(μA) PEAK FORWARD SURGE CURRENT,(A) 200 100 50 0 0 10 100 1.0 TJ=25℃ .1 .01 0 20 40 60 80 100 120 PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) NUMBER OF CYCLES AT 60Hz - 74 - 140