BR3505 THRU BR3510 HIGH CURRENT 35AMPS.SINGLE PHASE BRIDGE RECTIFIER BR-25 FEATURE 1.142(29.0) 1.102(28.0) .673(17.1) .633(16.1) .UL Recognized File # E-96005 .Metal case with an electrically isolated epoxy .Rating to 1,000V PRV. .Low forward voltage drop .High temperature soldering guaranteed: 260℃/10seconds at5 lbs.,(2.3Kg) tension. .Mounting:thru hole for #8 screw Isolated voltage from case to lead over 2000 volts. HOLE FOR NO. 8 SCREW .732(18.6) .692(17.6) .673(17.1) 1.142(29.0) .633(16.1) 1.102(28.0) .582(14.8) .543(13.8) MECHANICAL DATA .Case: Molded plastic .Epoxy: UL 94V-0 rate flame retardant .Lead: MIL-STD- 202E, Method 208 guaranteed .Polarity: As marked .Mounting position: Any .Weight: 30grams .500 (12.7) .033X.250 (0.8X6.4) TYP. METAL HEAT SINK .452 MAX (11.5) .480(12.2) .425(10.8) Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS (single-phase, half-wave, 60HZ, resistive or inductive load rating at 25°C, unless otherwise stated) Type Number Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC blocking Voltage Maximum Average Forward rectified Output Current at TA=55°C Peak Forward Surge Current 8.3ms single half sinewave superimposed on rate load (JEDEC method) Maximum Forward Voltage Drop per element at 17.5A DC Maximum DC Reverse Current at @Ta =25°C rated DC blocking voltage per element @Ta =100°C 2 I t Rating for Fusing (t﹤8.3ms) Typical Junction Capacitance(Note 1) Typical Thermal Resistance(Note 2) Storage Temperature Operating Junction Temperature SYM BOL BR 3505 BR 351 BR 352 BR 354 BR 356 BR 358 BR 3510 units VRRM VRMS VDC 50 100 200 400 600 800 1000 V 35 70 140 280 420 560 700 V 50 100 200 400 600 800 1000 V IF(AV) 35.0 A IFSM 400 A VF 1.1 V 10.0 uA 500 664 uA A Sec 300 pF 2.2 °C /W -55 to +150 °C -55 to +125 °C IR 2 It CJ R(JA) TSTG TJ Note: 1. Measured at 1.0 MHz and applied reverse voltage of 4.0Vdc 2.Thermal Resistance from Junction to lead mounted on on P.C.B. with 0.5×0.5”(13×13mm) copper pads. - 19 - 2 RATING AND CHARACTERISTIC CURVES (BR3505 THRU BR3510) FIG.1-TYPICAL FORWARD CURRENT DERATING CURVE FIG.2-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS INSTANEOUS FORWARD CURRENT,(A) AVERGE FORWARD RECTIFIED CURRENT,(A) 100 35 17.5 Single Phase Half Wave 60Hz Resistive or inductive Load 0 0 50 100 150 10 1.0 .1 200 TJ=25℃ Pulse Width=300μs 1% Duty Cycle AMBIENT TEMPERTURE,(℃) 1.0 .8 .6 1.2 1.4 INSTANEOUS FORWARD VOLTAGE,(V) FIG.4-TYPICAL REVERSE CHARACTERISTICS FIG.3-MAXIMUN NON-REPETITIVE FORWARD SURGE CURRENT 10 8.3ms Single Half Sine-Wave (JEDEC Method) 300 INSTANEOUS REVERSE CURRENT,(μA) PEAK FORWARD SURGE CURRENT,(A) 400 200 100 0 0 10 100 1.0 TJ=25℃ .1 .01 0 20 40 60 80 100 120 PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) NUMBER OF CYCLES AT 60Hz - 20 - 140