NCP1080 Integrated PoE-PD & DC-DC Converter Controller Introduction The NCP1080 is a member of ON Semiconductor’s Power over Ethernet Powered Device (PoE−PD) product family and represents a robust, flexible and highly integrated solution targeting demanding Ethernet applications. It combines in a single unit an enhanced PoE−PD interface fully supporting the IEEE802.3af specification and a flexible and configurable DC−DC converter controller. The NCP1080’s exceptional capabilities offer new opportunities for the design of products powered directly over Ethernet lines, eliminating the need for local power adaptors or power supplies and drastically reducing the overall installation and maintenance cost. ON Semiconductor’s unique manufacturing process and design enhancements allow the NCP1080 to deliver up to 13 W of regulated power to support PoE applications according to the IEEE802.3af standard. This device leverages the significant cost advantages of PoE−enabled systems to a broad spectrum of products in markets such as VoIP phones, wireless LAN access point, security cameras, point of sales terminals, RFID readers, industrial ethernet devices, etc. The integrated current mode DC−DC controller facilitates isolated and non−isolated fly−back, forward and buck converter topologies. It has all the features necessary for a flexible, robust and highly efficient design including programmable switching frequency, duty cycle up to 80 percent, slope compensation, and soft start−up. The NCP1080 is fabricated in a robust high voltage process and integrates a rugged vertical N−channel DMOS with a low loss current sense technique suitable for the most demanding environments and capable of withstanding harsh environments such as hot swap and cable ESD events. The NCP1080 complements ON Semiconductor’s ASSP portfolio in communications and industrial devices and can be combined with other high−voltage interfacing devices to offer complete solutions to the communication, industrial and security markets. Features • These are Pb−Free Devices • May, 2013 − Rev. 7 NCP1080 = Specific Device Code XXXX = Date Code Y = Assembly Location ZZ = Traceability Code ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 2 of this data sheet. Robustness of Discrete MOSFETs with Integrated Temperature Control Fully Supports IEEE802.3af Standard Regulated Power Output up to 13 W Programmable Classification Current Adjustable Under Voltage Lock Out Programmable Inrush Current Limit Programmable Operational Current Limit up to 500 mA Over−temperature Protection Industrial Temperature Range −40°C to 85°C with Full Operation up to 150°C Junction Temperature 0.6 W Hot−swap Pass−switch with Low Loss Current Sense Technique © Semiconductor Components Industries, LLC, 2013 1 TSSOP−20 EP DE SUFFIX CASE 948AB • Vertical N−channel DMOS Pass−switch Offers the Powered Device Interface • • • • • • • • http://onsemi.com DC−DC Converter Controller • Current Mode Control • Supports Isolated and Non−isolated DC−DC Converter Applications • Internal Voltage Regulators • Wide Duty Cycle Range with Internal Slope Compensation Circuitry • Programmable Oscillator Frequency • Programmable Soft−start Time 1 Publication Order Number: NCP1080/D NCP1080 PIN DIAGRAM VPORTP CLASS UVLO INRUSH ILIM1 VPORTN1 RTN VPORTN2 TEST1 TEST2 SS FB COMP VDDL VDDH GATE ARTN NC CS OSC 1 Exposed Pad (Top View) ORDERING INFORMATION Package Shipping Configuration† Temperature Range NCP1080DEG TSSOP−20 EP (Pb−Free) 74 units / Tube −40°C to 85°C NCP1080DER2G TSSOP−20 EP (Pb−Free) 2500 / Tape & Reel −40°C to 85°C Part Number †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specification Brochure, BRD8011/D. VPORTP DETECTION CLASS THERMAL SHUT DOWN INTERNAL SUPPLY & BANDGAP VDDH VDDH VDDL VDDL CLASSIFICATION VDDL VDDL 5 mA SS UVLO UVLO VPORT MONITOR VDDL 5K DC−DC CONVERTER CONTROL 1.2 V FB COMP CS INRUSH ILIM1 INRUSH ILIM1 OSC HOT SWAP SWITCH CONTROL & CURRENT OSC VDDH GATE LIMIT BLOCKS NC ARTN RTN VPORTN1,2 Figure 1. NCP1080 Block Diagram http://onsemi.com 2 NCP1080 SIMPLIFIED APPLICATION DIAGRAMS RJ−45 CLASS Cline DB1 Z_line Rinrush Data Pairs Rilim1 Cpd VPORTP Rclass VDDH INRUSH ILIM1 VDDL Cvddl NCP1080 UVLO FB OSC COMP DB2 R5 OC1 Rcs C2 ARTN SS VPORTN2 Cload Rslope CS TEST1 Spare Pairs LD1 M1 GATE TEST2 VPORTN1 R3 RTN Optocoupler Rosc Css Voutput Rd1 R1 R2 D1 T1 Cvddh Z1 C1 R4 Figure 2. Isolated Fly−back Converter Figure 2 shows the integrated PoE−PD switch and DC−DC controller configured to work in a fully isolated application. The output voltage regulation is accomplished with an external opto−coupler and a shunt regulator (Z1). RJ−45 Rclass Cline DB1 Z_line Rinrush Data Pairs Rilim1 Cpd VPORTP CLASS INRUSH ILIM1 Cvddh VDDL Cvddl NCP1080 R2 TEST2 CS TEST1 FB Css OSC VPORTN1 VPORTN2 COMP DB2 R3 Cload M1 GATE SS Spare Pairs LD1 Rd1 R1 UVLO Voutput T1 VDDH Rslope R4 Rcs ARTN RTN Rosc C1comp Rcomp C2comp Figure 3. Non−Isolated Fly−back Converter Figure 3 shows the integrated PoE−PD and DC−DC controller configured in a non−isolated fly−back configuration. A compensation network is inserted between the FB and the COMP pin for overall stability of the feedback loop. http://onsemi.com 3 NCP1080 SIMPLIFIED APPLICATION DIAGRAMS D2 VPORTP RJ−45 Rclass Cline Z_line DB1 R5 CLASS Rinrush Data Pairs VDDH ILIM1 D1 VDDL LD1 Cvddl Cload NCP1080 UVLO Rslope CS TEST2 FB COMP OSC SS VPORTN1 VPORTN2 DB2 M1 GATE TEST1 Spare Pairs R3 Rd1 R1 R2 Voutput Cpd Cvddh INRUSH Rilim1 T1 Css Rosc R4 Rcs ARTN RTN C1comp Rcomp C2comp Figure 4. Non−Isolated Fly−back with Extra Winding Figure 4 shows the same non−isolated fly−back configuration as Figure 3, but adds a 12 V auxiliary bias winding on the transformer to provide power to the NCP1080 DC−DC controller via its VDDH pin. This topology shuts off the current flowing from VPORTP to VDDH and therefore reduces the internal power dissipation of the PD, resulting in higher overall power efficiency. D3 T1 Cpd RJ−45 DB1 Cline Rinrush Z_line Data Pairs Rclass Rilim1 VPORTP D1 CLASS VDDH INRUSH Cvddl Voutput D2 Cvddh VDDL L1 R3 LD1 Cload ILIM1 NCP1080 Rd1 R1 UVLO R2 TEST2 CS TEST1 FB OSC Css Rosc COMP VPORTN1 VPORTN2 SS Spare Pairs DB2 M1 GATE Rslope R4 Rcs ARTN RTN C1comp Rcomp C2comp Figure 5. Non−Isolated Forward Converter Figure 5 shows the NCP1080 used in a non−isolated forward topology. http://onsemi.com 4 NCP1080 Table 1. PIN DESCRIPTIONS Name Pin No. Type 1 Supply Positive input power. Voltage with respect to VPORTN1,2 6,8 Ground Negative input power. Connected to the source of the internal pass−switch. RTN 7 Ground DC−DC controller power return. Connected to the drain of the internal pass−switch. It must be connected to ARTN. This pin is also the drain of the internal pass−switch. ARTN 14 Ground DC−DC controller ground pin. Must be connected to RTN as a single point ground connection for improved noise immunity. VDDH 16 Supply Output of the 9 V LDO internal regulator. Voltage with respect to ARTN. Supplies the internal gate driver. VDDH must be bypassed to ARTN with a 1 mF or 2.2 mF ceramic capacitor with low ESR. VDDL 17 Supply Output of the 3.3 V LDO internal regulator. Voltage with respect to ARTN. This pin can be used to bias an external low−power LED (1 mA max.) connected to ARTN, and can also be used to add extra biasing current in the external opto−coupler. VDDL must be bypassed to ARTN with a 330 nF or 470 nF ceramic capacitor with low ESR. CLASS 2 Input Classification current programming pin. Connect a resistor between CLASS and VPORTN1,2. INRUSH 4 Input Inrush current limit programming pin. Connect a resistor between INRUSH and VPORTN1,2. ILIM1 5 Input Operational current limit programming pin. Connect a resistor between ILIM1 and VPORTN1,2. UVLO 3 Input DC−DC controller under−voltage lockout input. Voltage with respect to VPORTN1,2. Connect a resistor−divider from VPORTP to UVLO to VPORTN1,2 to set an external UVLO threshold. GATE 15 Output OSC 11 Input NC 13 COMP 18 I/O Output of the internal error amplifier of the DC−DC controller. COMP is pulled−up internally to VDDL with a 5 kW resistor. In isolated applications, COMP is connected to the collector of the opto−coupler. Voltage with respect to ARTN. FB 19 Input DC−DC controller inverting input of the internal error amplifier. In isolated applications, the pin should be strapped to ARTN to disable the internal error amplifier. CS 12 Input Current−sense input for the DC−DC controller. Voltage with respect to ARTN. SS 20 Input Soft−start input for the DC−DC controller. A capacitor between SS and ARTN determines the soft−start timing. TEST1 9 Input Digital test pin must always be connected to VPORTN1,2. TEST2 10 Input Digital test pin must always be connected to VPORTN1,2. VPORTP VPORTN1 VPORTN2 EP Description DC−DC controller gate driver output pin. Internal oscillator frequency programming pin. Connect a resistor between OSC and ARTN. No connect pin, must not be connected. Exposed pad. Connected to VPORTN1,2 ground. http://onsemi.com 5 NCP1080 Table 2. ABSOLUTE MAXIMUM RATINGS Symbol Min. Max. Units Input power supply −0.3 72 V Voltage with respect to VPORTN1,2 RTN ARTN Analog ground supply 2 −0.3 72 V Pass−switch in off−state (Voltage with respect to VPORTN1,2) VDDH Internal regulator output −0.3 17 V Voltage with respect to ARTN VDDL Internal regulator output −0.3 3.6 V Voltage with respect to ARTN CLASS Analog output −0.3 3.6 V Voltage with respect to VPORTN1,2 INRUSH Analog output −0.3 3.6 V Voltage with respect to VPORTN1,2 ILIM1 Analog output −0.3 3.6 V Voltage with respect to VPORTN1,2 UVLO Analog input −0.3 3.6 V Voltage with respect to VPORTN1,2 OSC Analog output −0.3 3.6 V Voltage with respect to ARTN Analog input / output −0.3 3.6 V Voltage with respect to ARTN FB Analog input −0.3 3.6 V Voltage with respect to ARTN CS Analog input −0.3 3.6 V Voltage with respect to ARTN SS Analog input −0.3 3.6 V Voltage with respect to ARTN NC Open pin Digital inputs −0.3 3.6 V Voltage with respect to VPORTN1,2 TA Ambient temperature −40 85 °C TJ Junction temperature − 150 °C Junction temperature (Note 1) − 175 °C −55 150 °C 37.6 °C/W 4 − kV 750 − V Machine Model 300 − V Latch−up ±200 − mA System ESD (contact/air) (Note 3) 8/15 − kV VPORTP COMP TEST1 TEST2 TJ−TSD Parameter Tstg Storage Temperature TθJA Thermal Resistance, Junction to Air (Note 2) ESD−HBM Human Body Model ESD−CDM Charged Device Model ESD−MM LU ESD−SYS Conditions Thermal shutdown condition Exposed pad connected to VPORTN1,2 ground per JEDEC Standard JESD22 per JEDEC Standard JESD78 Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. TJ−TSD allowed during error conditions only. It is assumed that this maximum temperature condition does not occur more than 1 hour cumulative during the useful life for reliability reasons. 2. Mounted on a 1S2P (3 layer) test board with copper coverage of 25 percent for the signal layers and 90 percent copper coverage for the inner planes at an ambient temperature of 85°C in still air. Refer to JEDEC JESD51−7 for details. 3. Surges per EN61000−4−2, 1999 applied between RJ−45 and output ground and between adapter input and output ground of the evaluation board. The specified values are the test levels and not the failure levels. http://onsemi.com 6 NCP1080 Recommended Operating Conditions Operating conditions define the limits for functional operation and parametric characteristics of the device. Note that the functionality of the device outside the operating conditions described in this section is not warranted. Operating outside the recommended operating conditions for extended periods of time may affect device reliability. All values concerning the DC−DC controller, VDDH and VDDL blocks are with respect to ARTN. All others are with respect to VPORTN1,2 (unless otherwise noted). Table 3. OPERATING CONDITIONS Symbol Parameter Min. Typ. Max. Units 0 57 V 1.4 9.5 V 23.75 26.25 kW Conditions INPUT SUPPLY VPORT Input supply voltage VPORT = VPORTP − VPORTN1,2 SIGNATURE DETECTION Vsignature Input supply voltage signature detection range Rsignature Signature resistance (Note 4) Offset_current I_VportP + I_Rtn − 1.8 5 mA VPORTP = RTN = 1.4 V Sleep_current I_VportP + I_Rtn − 15 25 mA VPORTP = RTN = 9.5 V 20.5 V CLASSIFICATION Vcl Input supply voltage classification range 13 Iclass0 Class 0: Rclass 10 kW (Note 5) 0 − 4 mA Iclass0 = I_VportP + I_Rdet Iclass1 Class 1: Rclass 130 W (Note 5) 9 − 12 mA Iclass1 = I_VportP + I_Rdet Iclass2 Class 2: Rclass 69.8 W (Note 5) 17 − 20 mA Iclass2 = I_VportP + I_Rdet Iclass3 Class 3: Rclass 44.2 W (Note 5) 26 − 30 mA Iclass3 = I_VportP + I_Rdet Iclass4 Class 4: Rclass 30.9 W (Note 5) 36 − 44 mA Iclass4 = I_VportP + I_Rdet IDCclass Internal current consumption during classification (Note 6) − 600 − mA For information only 38 40 V UVLO pin tied to VPORTN1,2 29.5 32 − V UVLO pin tied to VPORTN1,2 UVLO Vuvlo_on Default turn on voltage (VportP rising) Vuvlo_off Default turn off voltage (VportP falling) Vhyst_int UVLO internal hysteresis − 6 − V UVLO pin tied to VPORTN1,2 Vuvlo_pr UVLO external programming range 25 − 50 V UVLO pin connected to the resistor divider (R1 & R2). For information only Vhyst_ext UVLO external hysteresis − 15 − % UVLO pin connected to the resistor divider (R1 & R2) Uvlo_Filter UVLO on/off filter time − 90 − mS 4. Test done according to the IEEE802.3af 2 Point Measurement. The minimum probe voltages measured at the PoE−PD are 1.4 V and 2.4 V, and the maximum probe voltages are 8.5 V and 9.5 V. 5. Measured with an external Rdet of 25.5 kW between VPORTP and VPORTN1,2, and for 13 V < VPORT < 20.5 V (with VPORT = VPORTP – VPORTN1,2). Resistors are assumed to have 1% accuracy. 6. This typical current excludes the current in the Rclass and Rdet external resistors. http://onsemi.com 7 NCP1080 Table 3. OPERATING CONDITIONS Symbol Parameter Min. Typ. Max. Units Conditions PASS−SWITCH AND CURRENT LIMITS Ron Pass−switch Rds−on − 0.6 1.2 W Max Ron specified at Tj = 130°C I_Rinrush1 Rinrush = 150 kW (Note 7) 95 125 155 mA Measured at RTN− VPORTN1,2 = 3 V I_Rinrush2 Rinrush = 57.6 kW (Note 7) 260 310 360 mA Measured at RTN− VPORTN1,2 = 3 V I_Rilim1 Rilim1 = 84.5 kW (Note 7) 450 510 570 mA Current limit threshold 0.8 1 1.2 V RTN−VPORTN1,2 falling; voltage with respect to VPORTN1,2 Voltage with respect to VPORTN1,2 INRUSH AND ILIM1 CURRENT LIMIT TRANSITION Vds_pgood VDS required for power good status Vds_pgood_hyst VDS hysteresis required for power good status − 8.2 − V VDDH_reg Regulator output voltage (Notes 8 and 9) Ivddh_load + Ivddl_load < 10 mA with 0 < Ivddl_load < 2.25 mA 8.4 9 9.6 V VDDH_Off Regulator turn−off voltage − VDDH_reg + 0.5 V − V VDDH_lim VDDH regulator current limit (Notes 8 and 9) 13 − 26 mA VDDH_Por_R VDDH POR level (rising) 7.3 − 8.3 V VDDH_Por_F VDDH POR level (falling) 6 − 7 V VDDH_ovlo VDDH over−voltage level (rising) 16 − 18.5 V 3.05 3.3 3.55 V VDDH REGULATOR For information only VDDL REGULATOR VDDL_reg Regulator output voltage (Notes 8 and 9) 0 < Ivddl_load < 2.25 mA with Ivddh_load + Ivddl_load < 10 mA VDDL_Por_R VDDL POR level (rising) VDDL – 0.2 − VDDL – 0.02 V VDDL_Por_F VDDL POR level (falling) 2.5 − 2.9 V Gate_Tr GATE rise time (10−90%) − − 50 ns Cload = 2 nF, VDDHreg = 9 V Gate_Tf GATE fall time (90−10%) − − 50 ns Cload = 2 nF, VDDHreg = 9 V 1.3 − 3 V For information only GATE DRIVER PWM COMPARATOR VCOMP COMP control voltage range 7. The current value corresponds to the PoE−PD input current (the current flowing in the external Rdet and the quiescent current of the device are included). Resistors are assumed to have 1% accuracy. 8. Power dissipation must be considered. Load on VDDH and VDDL must be limited especially if VDDH is not powered by an auxiliary winding. 9. Ivddl_load = current flowing out of the VDDL pin. Ivddh_load = current flowing out of the VDDH pin + current delivered to the Gate Driver (function of the frequency, VDDH voltage & MOSFET gate capacitance). http://onsemi.com 8 NCP1080 Table 3. OPERATING CONDITIONS Symbol Parameter Min. Typ. Max. Units Conditions ERROR AMPLIFIER Vbg_fb Reference voltage 1.15 1.2 1.25 V Voltage with respect to ARTN Av_ol DC open loop gain − 80 − dB For information only GBW Error amplifier GBW 1 − − MHz For information only Vss Soft−start voltage range − 1.15 − V Vss_r Soft−start low threshold (rising edge) 0.35 0.45 0.55 V Iss Soft−start source current 3 5 7 mA SOFT−START CURRENT LIMIT COMPARATOR CSth CS threshold voltage 324 360 396 mV Tblank Blanking time − 100 − ns DutyC Maximum duty cycle − 80% − Frange Oscillator frequency range 100 − 500 F_acc Oscillator frequency accuracy For information only OSCILLATOR Fixed internally kHz % ±25 CURRENT CONSUMPTION IvportP1 VPORTP internal current consumption (Note 10) − 2.5 3.5 mA DC−DC controller off IvportP2 VPORTP internal current consumption (Note 11) − 4.7 6.5 mA DC−DC controller on 150 − − °C Tj TJ = junction temperature − 15 − °C Tj TJ = junction temperature THERMAL SHUTDOWN TSD Thermal shutdown threshold Thyst Thermal hysteresis THERMAL RATINGS TA Ambient temperature −40 − 85 °C TJ Junction temperature − − 125 150 °C °C 10. Conditions a. No current through the pass−switch b. DC−DC controller inactive (SS shorted to RTN) c. No external load on VDDH and VDDL d. VPORTP = 57 V 11. Conditions a. No current through the pass−switch b. Oscillator frequency = 100 kHz c. No external load on VDDH and VDDL d. Aux winding not used e. 2 nF on GATE, DC−DC controller enabled f. VPORTP = 57 V http://onsemi.com 9 Parametric values guaranteed Max 1000 hours NCP1080 DESCRIPTION OF OPERATION Powered Device Interface Power Mode The PD interface portion of the NCP1080 supports the IEEE802.3af defined operating modes: detection signature, current source classification, inrush and operating current limits. In order to give more flexibility to the user and also to keep control of the power dissipation in the NCP1080, both current limits are configurable. The device enters operation once its programmable Vuvlo_on threshold is reached, and operation ceases when the supplied voltage falls below the Vuvlo_off threshold. Sufficient hysteresis and Uvlo filter time are provided to avoid false power on/off cycles due to transient voltage drops on the cable. When the classification hand−shake is completed, the PSE and PD devices move into the operating mode. Under Voltage Lock Out (UVLO) The NCP1080 incorporates an under voltage lock out (UVLO) circuit which monitors the input voltage and determines when to apply power to the DC−DC controller. To use the default settings for UVLO (see Table 3), the pin UVLO must be connected to VPORTN1,2. In this case the signature resistor has to be placed directly between VPORTP and VPORTN1,2, as shown in Figure 7. Detection VPORTP During the detection phase, the incremental equivalent resistance seen by the PSE through the cable must be in the IEEE802.3af standard specification range (23.75 kW to 26.25 kW) for a PSE voltage from 2.7 V to 10.1 V. In order to compensate for the non−linear effect of the diode bridge and satisfy the specification at low PSE voltage, the NCP1080 presents a suitable impedance in parallel with the 25.5 kW Rdet external resistor connected between VPORTP and VPORTN. For some types of diodes (especially Schottky diodes), it may be necessary to adjust this external resistor. When the Detection_Off level is detected (typically 11.5 V) on VPORTP, the NCP1080 turns on its internal 3.3 V regulator and biasing circuitry in anticipation of the classification phase as the next step. VPORT VPORTN1,2 NCP1080 Figure 7. Default UVLO Settings To define the UVLO threshold externally, the UVLO pin must be connected to the center of an external resistor divider between VPORTP and VPORTN1,2 as shown in Figure 8. The series resistance value of the external resistors must add to 25.5 kW and replaces the internal signature resistor. Classification Once the PSE device has detected the PD device, the classification process begins. In classification, the PD regulates a constant current source that is set by the external resistor RCLASS value on the CLASS pin. Figure 6 shows the schematic overview of the classification block. The current source is defined as: I class + VPORTP V bg R class UVLO Rdet VPORTP R1 VPORT , (where V bg is 1.2 V) UVLO R2 VDDA1 1.2 V VPORTN1,2 NCP1080 Figure 8. External UVLO Configuration CLASS For a Vuvlo_on desired turn−on voltage threshold, R1 and R2 can be calculated using the following equations: Rclass R1 ) R2 + R det R2 + VPORTN1,2 NCP1080 Figure 6. Classification Block Diagram http://onsemi.com 10 1.2 V ulvo_on R det NCP1080 When using the external resistor divider, the NCP1080 has an external reference voltage hysteresis of 15% typical. Inrush and Operational Current Limitations The inrush current limit and the operational current limit are programmed individually by an external Rinrush and Rilim1 resistors respectively connected between INRUSH and VPORTN1,2, and between ILIM1 and VPORTN1,2 as shown in Figure 9. VDDA1 VDDA1 Vbg1 ILIM1 / INRUSH Ilim_ref NCP1080 VPORTNx Figure 9. Current Limitation Configuration (Inrush & Ilim1 Pins) Inrush 0 Ilim1 1 I_pass_switch & VDS_PGOOD Vds_pgood threshold Current_limit_ON detector VDDA1 VDDA1 VDDA1 2V 1 V / 9.2 V VPORTNx RTN Pass Switch NCP1080 Figure 10. Inrush and Ilim1 Selection Mechanism enabled once the pass−switch is not limiting the current anymore, meaning that the Cpd capacitor is fully charged. When VPORT reaches the UVLO_on level, the Cpd capacitor is charged with the INRUSH current (in order to limit the internal power dissipation of the pass−switch). Once the Cpd capacitor is fully charged, the current limit switches from the inrush current to the current limit level (ilim1) as shown in Figure 10. This transition occurs when both following conditions are satisfied: 1. The VDS of the pass−switch is below the Vds_pgood low level (1 V typical). 2. The pass−switch is no longer in current limit mode, meaning the gate of the pass−switch is “high” (above 2 V typical). The operational current limit will stay selected as long as Vds_pgood is true (meaning that RTN−VPORTN1,2 is below the high level of Vds_pgood). This mechanism allows a current level transition without any current spike in the pass−switch because the operational current limit (ilim1) is Thermal Shutdown The NCP1080 includes thermal protection which shuts down the device in case of high power dissipation. Once the thermal shutdown (TSD) threshold is exceeded, following blocks are turned off: • DC−DC controller • Pass−switch • VDDH and VDDL regulators • CLASS regulator When the TSD error disappears and if the input line voltage is still above the UVLO level, the NCP1080 automatically restarts with the current limit set in the inrush state, the DC−DC controller is disabled and the Css http://onsemi.com 11 NCP1080 DC−DC Converter Controller (soft−start capacitor) discharged. The DC−DC controller becomes operational as soon as RTN−VPORTN1,2 is below the Vds_pgood threshold. The NCP1080 implements a current mode DC−DC converter controller which is illustrated in Figure 11. VPORTP OSC VDDL 5 kW 1.2 V Oscillator Reset CLK FB Set CLK VDDL 3.3 V LDO COMP 9 V LDO Current Slope Compensation 10 mA 0 VDDH PWM comp CS Blanking time S Q 1.45 V 11 kW Gate Driver GATE R 2 ARTN Current limit comp VDDL 360 mV 5 mA SS Soft−start Figure 11. DC−DC Controller Block Diagram Internal VDDH and VDDL Regulators and Gate Driver In isolated topologies the error amplifier is not used because it is already implemented externally with the shunt regulator on the secondary side of the DC−DC controller (see Figure 2). Therefore the FB pin must be strapped to ARTN and the output transistor of the opto−coupler has to be connected on the COMP pin where an internal 5 kW pull−up resistor is tied to the VDDL supply (see Figure 11). An internal linear regulator steps down the VPORTP voltage to a 9 V output on the VDDH pin. VDDH supplies the internal gate driver circuit which drives the GATE pin and the gate of the external power MOSFET. The NCP1080 gate driver supports an external MOSFET with high Vth and high input gate capacitance. A second LDO regulator steps down the VDDH voltage to a 3.3 V output on VDDL. VDDL powers the analog circuitry of the DC−DC controller. In order to prevent uncontrolled operations, both regulators include power−on−reset (POR) detectors which prevent the DC−DC controller from operating when either VDDH or VDDL is too low. In addition, an over−voltage lockout (OVLO) on the VDDH supply disables the gate driver in case of an open−loop converter with a configuration using the bias winding of the transformer (see Figure 4). Both VDDH and VDDL regulators turn on as soon as VPORT reaches the Vuvlo_on threshold. Soft−Start The soft−start function provided by the NCP1080 allows the output voltage to ramp up in a controlled fashion, eliminating output voltage overshoot. This function is programmed by connecting a capacitor CSS between the SS and ARTN pins. While the DC−DC controller is in POR, the capacitor CSS is fully discharged. After coming out of POR, an internal current source of 5 mA typically starts charging the capacitor CSS to initiate soft−start. When the voltage on SS pin has reached 0.45 V (typical), the gate driver is enabled and DC−DC operation starts with a duty cycle limit which increases with the SS pin voltage. The soft−start function is finished when the SS pin voltage goes above 1.6 V for which the duty cycle limit reaches its maximum value of 80%. Soft−start can be programmed by using the following equation: Error Amplifier In non−isolated converter topologies, the high gain internal error amplifier of the NCP1080 and the internal 1.2 V reference voltage regulate the DC−DC output voltage. In this configuration, the feedback loop compensation network should be inserted between the FB and COMP pins as shown in Figures 3, 4 and 5. t SS(ms) + 0.23 http://onsemi.com 12 C SS(nF) NCP1080 Current Limit Comparator conduction mode (CCM) and when the duty cycle is close or above 50%, the NCP1080 integrates a current slope compensation circuit. The amplitude of the added slope compensation is typically 110 mV over one cycle. As an example, for an operating switching frequency of 250 kHz, the internal slope provided by the NCP1080 is 27.5 mV/ mA typically. The NCP1080 current limit block behind the CS pin senses the current flowing in the external MOSFET for current mode control and cycle−by−cycle current limit. This is performed by the current limit comparator which, on the CS pin, senses the voltage across the external Rcs resistor located between the source of the MOSFET and the ARTN pin. The NCP1080 also provides a blanking time function on CS pin which ensures that the current limit and PWM comparators are not prematurely trigged by the current spike that occurs when the switching MOSFET turns on. DC−DC Controller Oscillator The frequency is configured with the Rosc resistor inserted between OSC and ARTN, and is defined by the following equation: R OSC(kW) + Slope Compensation Circuitry To overcome sub−harmonic oscillations and instability problems that exist with converters running in continuous 38600 F OSC(kHz) The duty cycle limit is fixed internally at 80%. http://onsemi.com 13 NCP1080 PACKAGE DIMENSIONS TSSOP−20 EP CASE 948AB−01 ISSUE O D B B DETAIL B 20 e/2 0.20 C A-B D 11 2X 10 TIPS E1 DETAIL B ÉÉÉ ÉÉÉ PIN 1 REFERENCE 1 E b b1 D 10 e 20X A SECTION B−B b 0.10 TOP VIEW M C A-B D M A2 B 0.05 C B A DETAIL A END VIEW 0.08 C 20X ÍÍÍÍ ÍÍÍÍ ÍÍÍÍ c c1 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.07 IN EXCESS OF THE LEAD WIDTH AT MMC. DAMBAR CANNOT BE LOACTED ON THE LOWER RADIUS OR THE FOOT OF THE LEAD. 4. DIMENSIONS b, b1, c, c1 TO BE MEASURED BETWEEN 0.10 AND 0.25 FROM LEAD TIP. 5. DATUMS A AND B ARE ARE DETERMINED AT DATUM H. DATUM H IS LOACTED AT THE MOLD PARTING LINE AND COINCIDENT WITH LEAD WHERE THE LEAD EXITS THE PLASTIC BODY. 6. DIMENSION D DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.15 PER SIDE. DIMENSION E1 DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.15 PER SIDE. D AND E1 ARE DETERMINED AT DATUM H. SIDE VIEW A1 C SEATING PLANE H L2 P SEATING PLANE GAUGE PLANE L C DETAIL A P1 DIM A A1 A2 b b1 c c1 D E E1 e L L2 M P P1 MILLIMETERS MAX MIN --1.10 0.05 0.15 0.85 0.95 0.19 0.30 0.19 0.25 0.09 0.20 0.09 0.16 6.40 6.60 6.40 BSC 4.30 4.50 0.65 BSC 0.50 0.70 0.25 BSC 0_ 8_ --4.20 --3.00 SOLDERING FOOTPRINT* 4.30 BOTTOM VIEW 6.76 20X 0.98 3.10 0.65 PITCH 20X 0.35 DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 14 NCP1080 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 http://onsemi.com 15 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NCP1080/D