Model PD0922J5050D2HF Rev A Ultra Low Profile 0805 Power Divider 50Ω to 50Ω Description The PD0922J5050D2HF is a low profile, sub-miniature Wilkinson power divider in an easy to use surface mount package and is ideal for high volume manufacturing while delivering higher performances than traditional printed and lumped element solutions. It has been designed for the following markets: DVB-S, GSM, DCS, PCS, CDMA and GPS. The PD0922J5050D2HF is matched to 50 Ω and has a height profile of 0.8 mm which is ideal for high level integrations. A 2 section Wilkinson design results in increased isolation performance. Two external resistors are required for operation. Components are available on tape and reel for high volume manufacturing pick and place. Detailed Electrical Specifications: Specifications subject to change without notice. Features: • • • • • • • • • • • • 950 – 2150 MHz 12dB Isolation (output ports) Good Return Loss 0.8mm Height Profile 50Ω Outputs/Inputs External resistors required Low Insertion Loss Surface Mountable Tape & Reel Non-conductive Surface RoHS Compliant Halogen Free ROOM (25°°C) Parameter Min. Frequency Input Port Impedance Output Port Impedance Return Loss Insertion Loss* Amplitude Balance Phase Balance Isolation (Output Ports) Power Handling Operating Temperature 950 Typ. 50 50 11 0.7 0.1 1 12 9.3 10.5 Max Unit 2150 MHz Ω Ω dB dB dB Degrees dB Watts ºC 0.8 0.5 3 2 +85 -55 * Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 ºC) Outline Drawing TOP VIEW (Near Side) SIDE VIEW BOTTOM VIEW (Far Side) 4x 0.37 2.04±0.10 0.85±0.08 1 3 2 2x 0.15 1.29±0.10 6x 0.98 Orientation Marker Denotes Pin Location Orientation Marker Denotes Pin Location Mechanical Outline -Dimensions are in Millimeters Pin 1 2 3 4 5 6 6x 0.22 6 5 4 4x 0.65 6x 0.30 Designation Output 1 Input Mid 2 Mid 1 GND Output 2 Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model PD0922J5050D2HF Rev A Typical Broadband Performance: 500 MHz. to 8.0 GHz. Insertion Loss -3 -0.3 -6 -0.6 -9 -0.9 -12 -1.2 -15 -1.5 Amplitude Balance 1.5 15 1 10 0.5 5 Frequency [MHz] Frequency [MHz] Isolation 0 -3 -6 -9 -12 -15 -18 -21 -24 -27 -30 -33 8000 7500 7000 6500 6000 5500 5000 4500 4000 3500 3000 2500 2000 1500 1000 -36 500 [dB] 8000 7500 6500 6000 5500 5000 7000 Frequency [MHz] Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 8000 7500 7000 6500 6000 5500 5000 4500 4000 3500 3000 2500 2000 8000 7500 7000 6500 6000 5500 5000 -20 4500 -2 4000 -15 3500 -1.5 3000 -10 2500 -1 2000 -5 1500 -0.5 1500 0 1000 0 500 deg 20 1000 4500 Phase Balance 2 500 4000 Frequency [MHz] Frequency [MHz] [dB] 3500 3000 2500 500 8000 7500 7000 6500 6000 5500 5000 4500 4000 -3.6 3500 -36 3000 -3.3 2500 -3.0 -33 2000 -2.7 -30 1500 -2.4 -27 1000 -2.1 -24 2000 -1.8 -21 1500 -18 1000 [dB] 0.0 500 [dB] Return Loss - Input 0 Model PD0922J5050D2HF Rev A Typical Performance: 600 MHz. to 2600 MHz. Return Loss - Input Insertion Loss 0.0 -3 -0.3 -6 -0.6 -9 -0.9 -12 -1.2 -15 -1.5 [dB] -18 -1.8 -21 -2.1 -24 -2.4 -27 -2.7 -30 -3.0 -3.3 -33 2600 2500 2400 2300 2200 2100 2000 1900 1800 1700 1600 1500 1400 1300 1200 1100 900 1000 600 2600 2500 2400 2300 2200 2100 2000 1900 1800 1700 1600 1500 1400 1300 1200 1100 900 1000 800 700 600 800 -3.6 -36 700 [dB] 0 Frequency [MHz] Frequency [MHz] Phase Balance 1.5 15 1 10 0.5 5 deg 20 2600 2500 2400 2300 2200 2100 2000 1900 1800 1700 1600 1500 2600 2600 1400 2500 2500 1300 2400 2400 1200 2300 2300 1100 2200 2200 1000 2100 2100 900 2000 2000 Frequency [MHz] 800 1900 1900 1800 1700 1600 1500 1400 1300 1200 -20 1100 -2 1000 -15 900 -1.5 800 -10 700 -1 700 0 -5 600 0 -0.5 600 [dB] Amplitude Balance 2 Frequency [MHz] Isolation 0 -3 -6 -9 -12 -18 -21 -24 -27 -30 -33 1800 1700 1600 1500 1400 1300 1200 1100 1000 900 800 700 -36 600 [dB] -15 Frequency [MHz] Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model PD0922J5050D2HF Rev A Mounting Configuration: In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet published specifications. All of the Xinger components are constructed from organic PTFE based composites which possess excellent electrical and mechanical stability. Xinger components are compliant to a variety of ROHS and Green standards and ready for Pb-free soldering processes. Pads are Gold plated with a Nickel barrier. An example of the PCB footprint used in the testing of these parts is shown below. In specific designs, the transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances. In addition, since the PD0922J5050D2HF is a Wilkinson power divider, external 0402 100Ω and 200Ω resistors must be mounted in locations R1 and R2 respectively, as shown in the Figure below. Pad Footprint w/ Wilkinson 0402 Resistor Locations Circuit Pattern Dimensions are in Millimeters Mounting Footprint Footprint Pad (s) Solder Resist 3x Transmission lines .04 R1 4x .25 .66 R2 6x .41 6x .33 Plated thru holes to ground Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model PD0922J5050D2HF Rev A Packaging and Ordering Information Parts are available in reel and are packaged per EIA 481-2. Parts are oriented in tape and reel as shown below. Minimum order quantities are 4000 per reel. See Model Numbers below for further ordering information. 1.00 2.00 4.00 1.75 3.50 8.00 1.60 4.00 2.41 .25 Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282