Model PD0922J5050S2HF

Model PD0922J5050S2HF
Rev A
Ultra Low Profile 0805 Power Divider
50Ω to 50Ω
Description
The PD0922J5050S2HF is a low profile, sub-miniature Wilkinson power divider in
an easy to use surface mount package. The PD0922J5050S2HF is ideal for high
volume manufacturing and delivers higher performances than traditional printed and
lumped element solutions. The PD0922J5050S2HF is matched to 50 Ω and has a
height profile of 0.5 mm which is ideal for high level integrations in the following
markets: DVB-S, DVB-H (USA), GSM, DCS, PCS, CDMA, 3G and GPS. The
PD0922J5050S2HF does not include the resistive element and therefore, requires
an external resistor for operation. The PD0922J5050S2HF is available on tape and
reel for high volume manufacturing pick and place.
Detailed Electrical Specifications: Specifications subject to change without notice.
ROOM (25°°C)
Features:
•
•
•
•
•
•
•
•
•
•
•
•
950-2150 MHz
10dB Isolation (output ports)
High Return Loss
0.5mm Height Profile
50Ω Input / 50Ω Outputs
Low Insertion Loss
Surface Mountable
Tape & Reel
Non-conductive Surface
RoHS Compliant
External resistor required
Halogen Free
Parameter
Min.
Frequency
Input Port Impedance
Output Port Impedance
Return Loss
Insertion Loss*
Amplitude Balance
Phase Balance
Isolation (Output Ports)
Power Handling
950
Typ.
50
50
12
0.5
0.1
1
10
10.4
9
Operating Temperature
Max
Unit
2150
2
MHz
Ω
Ω
dB
dB
dB
Degrees
dB
Watts
+85
ºC
0.7
0.3
3
-55
* Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 ºC) Outline Drawing
TOP VIEW (Near Side)
SIDE VIEW
BOTTOM VIEW (Far Side)
4x 0.37
2.04±0.10
0.54±0.05
1
3
2
2x 0.15
1.29±0.10
6x 0.98
Orientation Marker
Denotes Pin Location
Orientation Marker
Denotes Pin Location
Mechanical Outline
-Dimensions are in Millimeters
Pin
1
2
3
4
5
6
6x
0.22
6
5
4
4x 0.65
6x
0.30
Designation
GND
Input
GND
Output 1
GND
Output 2
Visit us at
www.anaren.com
USA/Canada:
Toll Free:
Europe:
Asia:
(315) 432-8909
(800) 411-6596
+44 2392-232392
+86 512-62749282
Model PD0922J5050S2HF
Rev A
Typical Broadband Performance: 500 MHz. to 6.0 GHz.
Insertion Loss
0
-3
-3
-6
-6
-9
-12
-12
-15
-15
Amplitude Balance
1.5
15
1
10
0.5
5
Frequency [MHz]
Isolation
-3
-6
-9
-12
-15
-18
-21
-24
-27
-30
-33
6000
5500
5000
4500
4000
3500
3000
2500
2000
1500
1000
500
-36
Frequency [MHz]
Visit us at
www.anaren.com
USA/Canada:
Toll Free:
Europe:
Asia:
(315) 432-8909
(800) 411-6596
+44 2392-232392
+86 512-62749282
6000
5500
5000
Frequency [MHz]
0
[dB]
6000
5500
5000
4500
4500
4000
3500
3000
2500
2000
6000
5500
5000
4500
4000
-20
3500
-2
3000
-15
2500
-1.5
2000
-10
1500
-1
1500
0
-5
1000
0
-0.5
500
deg
20
1000
4000
Phase Balance
2
500
3500
Frequency [MHz]
Frequency [MHz]
[dB]
3000
2500
500
6000
5500
5000
4500
4000
3500
-36
3000
-33
-36
2500
-30
-33
2000
-27
-30
1500
-24
-27
1000
-21
-24
2000
-18
-21
1500
-18
1000
[dB]
-9
500
[dB]
Return Loss - Input
0
Model PD0922J5050S2HF
Rev A
Typical Performance: 600 MHz. to 2600 MHz.
Insertion Loss
-3
-0.3
-6
-0.6
-9
-0.9
-12
-1.2
-15
-1.5
Frequency [MHz]
2200
2300
2400
2500
2600
2400
2500
2600
1900
1700
1800
1900
1800
1700
1600
1500
1400
1300
1200
1100
1000
900
800
2600
2500
2400
2300
2200
2100
2000
-20
1900
-2
1800
-15
1700
-1.5
1600
-10
1500
-1
1400
-0.5
700
0
-5
600
0
1300
2300
5
1200
2100
0.5
1100
2200
10
1000
2000
1
900
2100
15
deg
1.5
800
1600
Phase Balance
20
700
2000
Amplitude Balance
2
600
1500
Frequency [MHz]
Frequency [MHz]
[dB]
1400
1300
1200
1100
900
600
2600
2500
2400
2300
2200
2100
2000
1900
1800
1700
1600
1500
1400
1300
1200
-3.6
1100
-3.3
-36
900
-3.0
-33
1000
-2.7
-30
800
-2.4
-27
700
-2.1
-24
1000
-1.8
-21
800
-18
700
[dB]
0.0
600
[dB]
Return Loss - Input
0
Frequency [MHz]
Isolation
0
-3
-6
-9
-12
-18
-21
-24
-27
-30
-33
2600
2500
2400
2300
2200
2100
2000
1900
1800
1700
1600
1500
1400
1300
1200
1100
1000
900
800
700
-36
600
[dB]
-15
Frequency [MHz]
Visit us at
www.anaren.com
USA/Canada:
Toll Free:
Europe:
Asia:
(315) 432-8909
(800) 411-6596
+44 2392-232392
+86 512-62749282
Model PD0922J5050S2HF
Rev A
Mounting Configuration:
In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be
used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet
published specifications.
An example of the PCB footprint used in the testing of these parts is shown below. In specific designs, the
transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying
pick and place equipment tolerances. In addition, since the PD0922J5050S2HF is a Wilkinson power divider, an
external 0603 100Ω resistor must be mounted in locations R1 as shown in the Figure below.
All of the Xinger components are constructed from ceramic filled PTFE composites which possess excellent electrical
o
and mechanical stability having X and Y thermal coefficient of expansion (CTE) of 17 ppm/ C.
Pad Footprint w/ 0603 Resistor Locations
Circuit Pattern
Dimensions are in Millimeters
Mounting Footprint
Footprint Pad (s)
3x Transmission
lines
Solder Resist
3x Plated thru
holes to ground
6x .33
.04
6x .41
4x .25
.66
R1
Visit us at
www.anaren.com
USA/Canada:
Toll Free:
Europe:
Asia:
(315) 432-8909
(800) 411-6596
+44 2392-232392
+86 512-62749282
Model PD0922J5050S2HF
Rev A
Packaging and Ordering Information
Parts are available in reels and are packaged per EIA 481-2. Parts are oriented in tape and reel as shown below. Minimum order
quantities are 4000 per reel. See Model Numbers below for further ordering information.
2.00
.81
4.00
1.75
3.50
8.00
1.60
4.00
2.41
.25
Visit us at
www.anaren.com
USA/Canada:
Toll Free:
Europe:
Asia:
(315) 432-8909
(800) 411-6596
+44 2392-232392
+86 512-62749282