Model PD1722J5050D2HF Rev A Ultra Low Profile 0805 Power Divider 50Ω to 50Ω Description The PD1722J5050D2HF is a low profile, sub-miniature Wilkinson power divider in an easy to use surface mount package. The PD1722J5050D2HF is ideal for high volume manufacturing and delivers higher performances than traditional printed and lumped element solutions. The PD1722J5050D2HF is matched to 50 Ω and has a height profile of 0.5 mm which is ideal for high level integrations in the following markets: WCDMA, and GSM, The PD1722J5050D2HF does not include the resistive element and therefore, requires an external resistor for operation. The PD1722J5050D2HF is available on tape and reel for high volume manufacturing pick and place. Detailed Electrical Specifications: Specifications subject to change without notice. ROOM (25°°C) Features: • • • • • • • • • • • 1700-2200 MHz 19 dB Isolation (output ports) 0.5mm Height Profile 50Ω Input / 50Ω Outputs Low Insertion Loss Surface Mountable Tape & Reel Non-conductive Surface RoHS Compliant External resistors required Halogen Free Parameter Min. Frequency Input Port Impedance Output Port Impedance Return Loss Insertion Loss* Amplitude Balance Phase Balance Isolation (Output Ports) Power Handling Operating Temperature 1700 Typ. 50 50 14 0.5 0.1 1 19 11 17 Max Unit 2200 MHz Ω Ω dB dB dB Degrees dB Watts ºC 0.7 0.3 3 2 +85 -55 * Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 ºC) Outline Drawing TOP VIEW (Near Side) SIDE VIEW BOTTOM VIEW (Far Side) 4x 0.37 2.04±0.10 0.85±0.08 1 3 2 2x 0.15 1.29±0.10 6x 0.98 Orientation Marker Denotes Pin Location Orientation Marker Denotes Pin Location Mechanical Outline -Dimensions are in Millimeters Pin 1 2 3 4 5 6 6x 0.22 6 5 4 4x 0.65 6x 0.30 Designation Output 1 Input Mid 2 Mid 1 GND Output 2 Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model PD1722J5050D2HF Rev A Typical Broadband Performance: 500 MHz. to 6.0 GHz. Insertion Loss 0 -3 -3 -6 -6 -9 -12 -12 -15 -15 1.5 15 1 10 0.5 5 Frequency [MHz] Isolation 0 -3 -6 -9 -12 -15 -18 -21 -24 -27 -30 -33 8000 7500 7000 6500 6000 5500 5000 4500 4000 3500 3000 2500 2000 1500 1000 -36 500 [dB] 8000 7500 7000 6500 6000 5500 5000 Frequency [MHz] Frequency [MHz] Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 8000 7500 7000 6500 6000 5500 5000 4500 4000 3500 3000 2500 2000 8000 7500 7000 6500 6000 5500 5000 4500 -20 4000 -2 3500 -15 3000 -1.5 2500 -10 2000 -5 -1 1500 -0.5 1500 0 1000 0 500 deg 20 1000 4500 Phase Balance Amplitude Balance 2 500 4000 Frequency [MHz] Frequency [MHz] [dB] 3500 3000 2500 500 8000 7500 7000 6500 6000 5500 5000 4500 4000 3500 -36 3000 -33 -36 2500 -30 -33 2000 -27 -30 1500 -24 -27 1000 -21 -24 2000 -18 -21 1500 -18 1000 [dB] -9 500 [dB] Return Loss - Input 0 Model PD1722J5050D2HF Rev A Typical Performance: 1600 MHz. to 2300 MHz. Insertion Loss -3 -0.3 -6 -0.6 -9 -0.9 -12 -1.2 -15 -1.5 Amplitude Balance 1.5 15 1 10 0.5 5 2300 2300 2200 2100 2000 1900 -20 2300 -2 2200 -15 2100 -1.5 2000 -10 1900 -5 -1 1800 -0.5 1800 0 1700 0 1600 deg 20 1700 2200 Phase Balance 2 1600 2100 Frequency [MHz] Frequency [MHz] [dB] 2000 1600 2300 2200 -3.6 2100 -3.3 -36 2000 -3.0 -33 1900 -2.7 -30 1800 -2.4 -27 1700 -2.1 -24 1900 -1.8 -21 1800 -18 1700 [dB] 0.0 1600 [dB] Return Loss - Input 0 Frequency [MHz] Frequency [MHz] Isolation 0 -3 -6 -9 -12 -18 -21 -24 -27 -30 -33 2300 2200 2100 2000 1900 1800 1700 -36 1600 [dB] -15 Frequency [MHz] Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model PD1722J5050D2HF Rev A Mounting Configuration: In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet published specifications. All of the Xinger components are constructed from organic PTFE based composites which possess excellent electrical and mechanical stability. Xinger components are compliant to a variety of ROHS and Green standards and ready for Pb-free soldering processes. Pads are Gold plated with a Nickel barrier. An example of the PCB footprint used in the testing of these parts is shown below. In specific designs, the transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances. In addition, since the PD1722J5050D2HF is a Wilkinson power divider, external 0402 100Ω and 200Ω resistors must be mounted in locations R1 and R2 respectively, as shown in the Figure below. Pad Footprint w/ 0402 Resistor Locations 3X Transmission Line 6X .014 [0.35] 6X .013 [0.33] R1 4X .012 [0.30] .026 [0.66] R2 Plated thru hole to ground Circuit Pattern Footprint Pad (s) Solder Resist Dimensions are in Inches [Millimeters] Mounting Footprint Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model PD1722J5050D2HF Rev A Packaging and Ordering Information Parts are available in reel and are packaged per EIA 481-2. Parts are oriented in tape and reel as shown below. Minimum order quantities are 4000 per reel. See Model Numbers below for further ordering information. 1.00 2.00 4.00 1.75 3.50 8.00 1.60 4.00 2.41 .25 Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282