Model B0922J7575AHF Rev A Ultra Low Profile 0805 Balun 75Ω to 75Ω Balanced Description The B0922J7575AHF is a low cost, low profile sub-miniature unbalanced to balanced transformer designed for differential inputs and output locations on modern chipsets in an easy to use surface mount package covering dual polarized commercial Satellite bands 950 MHz –1450 MHz & 1650 MHz – 2150 MHz. The B0922J7575AHF is ideal for high volume manufacturing and delivers higher performance than traditional wire wound baluns. The B0922J7575AHF has an unbalanced port impedance of 75Ω and a 75Ω balanced port impedance*. This transformation enables single ended signals to be applied to differential ports on modern integrated chipsets. The output ports have equal amplitude (-3dB) with 180 degree phase differential. The B0922J7575AHF is available on tape and reel for pick and place high volume manufacturing. Detailed Electrical Specifications: Specifications subject to change without notice. ROOM (25°°C) Features: • • • • • • • • • • • 950 – 2150 MHz 0.7mm Height Profile 75 Ohm to 2 x 37.5 Ohm Low Insertion Loss Sat LNB Chipset Compliant Input to Output DC Isolation Surface Mountable Tape & Reel Non-conductive Surface RoHS Compliant Halogen Free Parameter Min. Frequency Unbalanced Port Impedance Balanced Port Impedance Return Loss Insertion Loss* Amplitude Balance Phase Balance CMRR Power Handling 950 Operating Temperature -55 Typ. 75 75 9.6 0.8 0.4 3 26 7.9 Max Unit 2150 2 MHz Ω Ω dB dB dB Degrees dB Watts +85 ºC 1.2 1.4 9 * Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 ºC) Outline Drawing TOP VIEW (Near Side) SIDE VIEW BOTTOM VIEW (Far Side) 0.71±0.07 2.04±0.10 1 4x 0.37 2 3 2x 0.15 1.29±0.10 6x 0.98 6x 0.22 6 Orientation Marker Denotes Pin Location Orientation Marker Denotes Pin Location Mechanical Outline -Dimensions are in Millimeters -Tolerences are Non-Cumulative Pin 1 2 3 4 5 6 5 4 4x 0.65 6x 0.30 Designation GND Unbalanced Port GND Balanced Port NC Balanced Port Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model B0922J7575AHF Rev A Typical Performance: 800 MHz. to 2400 MHz. Amplitude Balance Return Loss - Input 2 0 -3 1.5 -6 1 -9 -12 0.5 [dB] -18 -21 0 -0.5 -24 -27 -1 -30 -1.5 -33 -36 1800 1900 2000 2100 2200 2300 2400 1900 2000 2100 2200 2300 2400 1700 1600 1800 Frequency [MHz] 1500 1400 1300 1200 1100 1000 800 2400 2300 2200 2100 2000 1900 1800 1700 1600 1500 1400 1300 1200 1100 1000 900 800 -2 900 [dB] -15 Frequency [MHz] Phase Balance Insertion Loss 20 0 -0.3 15 -0.6 10 -0.9 -1.2 5 deg -1.8 -2.1 0 -5 -2.4 -2.7 -10 -3 -15 -3.3 -3.6 Frequency [MHz] 1700 1600 1500 1400 1300 1200 1100 1000 900 2400 2300 2200 2100 2000 1900 1800 1700 1600 1500 1400 1300 1200 1100 1000 900 800 -20 800 [dB] -1.5 Frequency [MHz] CMRR 0 -3 -6 -9 -12 -18 -21 -24 -27 -30 -33 2600 2500 2400 2300 2200 2100 2000 1900 1800 1700 1600 1500 1400 1300 1200 1100 1000 900 -36 800 [dB] -15 Frequency [MHz] Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model B0922J7575AHF Rev A Mounting Configuration: In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet published specifications. All of the Xinger components are constructed from organic PTFE based composites which possess excellent electrical and mechanical stability. Xinger components are compliant to a variety of ROHS and Green standards and ready for Pb-free soldering processes. Pads are Gold plated with a Nickel barrier. An example of the PCB footprint used in the testing of these parts is shown below. An example of a DC-biased footprint is also shown below. In specific designs, the transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances. Mounting Footprint 6x .41 4x .25 6x .33 .66 .04 3x Transmission lines 2x Plated thru holes to ground Circuit Pattern Footprint Pad (s) Solder Resist Dimensions are in Millimeters Mounting Footprint Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model B0922J7575AHF Rev A Packaging and Ordering Information Parts are available in reel and are packaged per EIA 481-2. Parts are oriented in tape and reel as shown below. Minimum order quantities are 4000 per reel. See Model Numbers below for further ordering information. 2.00 .81 4.00 1.75 3.50 8.00 1.60 4.00 2.41 .25 Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282