Model B0310J50100AHF

Model B0310J50100AHF
Rev A
Ultra Low Profile 0805 Balun
50Ω to 100Ω Balanced
Description
The B0310J50100AHF is a low cost, low profile sub-miniature unbalanced to
balanced transformer designed for differential inputs and output locations on modern
chipsets in an easy to use surface mount. The B0310J50100AHF is ideal for high
volume manufacturing and delivers higher performance than traditional wire wound
baluns. The B0310J50100AHF has an unbalanced port impedance of 50Ω and a
100Ω balanced port impedance*. This transformation enables single ended signals
to be applied to differential ports on modern integrated chipsets. The output ports
have equal amplitude (-3dB) with 180 degree phase differential. The
B0310J50100AHF is available on tape and reel for pick and place high volume
manufacturing.
Detailed Electrical Specifications: Specifications subject to change without notice.
ROOM (25°°C)
Features:
•
•
•
•
•
•
•
•
300 – 1000 MHz
0.7mm Height Profile
50 Ohm to 2 x 50 Ohm
Surface Mountable
Tape & Reel
Non-conductive Surface
RoHS Compliant
Halogen Free
Parameter
Min.
Frequency
Unbalanced Port Impedance
Balanced Port Impedance
Return Loss
Insertion Loss*
Amplitude Balance
Phase Balance
CMRR
Power Handling
Operating Temperature
300
Typ.
50
100
9.4
0.8
2.5
34
9
8.1
Max
Unit
1000
MHz
Ω
Ω
dB
dB
dB
Degrees
dB
Watts
ºC
1.0
2.8
36
2
+85
-55
* Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 ºC)
Outline Drawing
TOP VIEW (Near Side)
SIDE VIEW
BOTTOM VIEW (Far Side)
4x 0.37
0.70±0.05
2.04±0.10
3
2
1
2x 0.15
1.29±0.10
6x 0.98
Orientation Marker
Denotes Pin Location
Orientation Marker
Denotes Pin Location
Mechanical Outline
-Dimensions are in Millimeters
-Tolerences are Non-Cumulative
Pin
1
2
3
4
5
6
6x
0.22
6
5
4
4x 0.65
6x
0.30
Designation
Unbalanced Port
GND
Balanced Port
Balanced Port
Do not connect
NC
Visit us at
www.Anaren.com
USA/Canada:
Toll Free:
Europe:
Asia:
(315) 432-8909
(800) 411-6596
+44 2392-232392
+86 512-62749282
Model B0310J50100A0HF
RevA
Typical Performance: 200 MHz. to 1100 MHz.
Insertion Loss
-3
-0.3
-6
-0.6
-9
-0.9
-12
-1.2
-15
-1.5
800
900
1000
1100
900
1000
1100
200
1100
1000
900
800
700
600
-3.6
500
-36
400
-3.3
300
-3
-33
800
-2.7
-30
700
-2.4
-27
600
-2.1
-24
500
-1.8
-21
400
-18
300
[dB]
0
200
[dB]
Return Loss - Input
0
Frequency [MHz]
Frequency [MHz]
Amplitude Balance
Phase Balance
50
4
40
3
30
2
20
10
deg
[dB]
1
0
0
-10
-1
-20
-2
700
600
500
400
300
1100
1000
900
800
700
600
500
400
300
-50
200
-40
-4
200
-30
-3
Frequency [MHz]
Frequency [MHz]
CM RR
0
-3
-6
-9
-12
-18
-21
-24
-27
-30
-33
1100
1000
900
800
700
600
500
400
300
-36
200
[dB]
-15
Frequency [MHz]
Visit us at
www.Anaren.com
USA/Canada:
Toll Free:
Europe:
Asia:
(315) 432-8909
(800) 411-6596
+44 2392-232392
+86 512-62749282
Model B0310J50100AHF
Rev A
Wide Band Performance: 0 MHz. to 8000 MHz.
Insertion Loss
-3
-0.3
-6
-0.6
-9
-0.9
-12
-1.2
-15
-1.5
5000
5500
6000
6500
7000
7500
8000
5500
6000
6500
7000
7500
8000
4500
4000
5000
Frequency [MHz]
3500
0
8000
7500
7000
6500
6000
5500
5000
4500
4000
3500
3000
2500
2000
-3.6
1500
-36
500
-3.3
1000
-3
-33
3000
-2.7
-30
2500
-2.4
-27
2000
-2.1
-24
1500
-1.8
-21
1000
-18
500
[dB]
0
0
[dB]
Re turn Loss - Input
0
Frequency [MHz]
Phase Balance
Amplitude Balance
50
4
40
3
30
2
20
10
deg
[dB]
1
0
0
-10
-1
-20
-2
-30
-3
-40
-4
Frequency [MHz]
4500
4000
3500
3000
2500
2000
1500
1000
500
0
8000
7500
7000
6500
6000
5500
5000
4500
4000
3500
3000
2500
2000
1500
1000
0
500
-50
Frequency [MHz]
CMRR
0
-3
-6
-9
-12
-18
-21
-24
-27
-30
-33
8000
7500
7000
6500
6000
5500
5000
4500
4000
3500
3000
2500
2000
1500
500
1000
-36
0
[dB]
-15
Frequency [MHz]
Visit us at
www.Anaren.com
USA/Canada:
Toll Free:
Europe:
Asia:
(315) 432-8909
(800) 411-6596
+44 2392-232392
+86 512-62749282
Model B0310J50100A0HF
RevA
Mounting Configuration:
In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be
used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet
published specifications.
All of the Xinger components are constructed from organic PTFE based composites which possess excellent
electrical and mechanical stability. Xinger components are compliant to a variety of ROHS and Green standards and
ready for Pb-free soldering processes. Pads are Gold plated with a Nickel barrier.
An example of the PCB footprint used in the testing of these parts is shown below. In specific designs, the
transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying
pick and place equipment tolerances.
Circuit Pattern
Dimensions are in Millimeters
Mounting Footprint
Footprint Pad (s)
Solder Resist
6x .41
4x .25
Plated thru holes to ground
3x Transmission
lines
.04
6x .33
.66
Visit us at
www.Anaren.com
USA/Canada:
Toll Free:
Europe:
Asia:
(315) 432-8909
(800) 411-6596
+44 2392-232392
+86 512-62749282
Model B0310J50100AHF
Rev A
Packaging and Ordering Information
Parts are available in reel and are packaged per EIA 481-2. Parts are oriented in tape and reel as shown below. Minimum order
quantities are 4000 per reel. See Model Numbers below for further ordering information.
2.00
.81
4.00
1.75
3.50
8.00
1.60
4.00
2.41
.25
Visit us at
www.Anaren.com
USA/Canada:
Toll Free:
Europe:
Asia:
(315) 432-8909
(800) 411-6596
+44 2392-232392
+86 512-62749282