ILI9325

ILI9325
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
Datasheet
Preliminary
Version: V0.28
Document No.: ILI9325DS_V0.28.pdf
ILI TECHNOLOGY CORP.
4F, No. 2, Tech. 5th Rd., Hsinchu Science Park,
Taiwan 300, R.O.C.
Tel.886-3-5670095; Fax.886-3-5670096
http://www.ilitek.com
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
Table of Contents
Section
Page
1. Introduction.................................................................................................................................................... 7
2. Features ........................................................................................................................................................ 7
3. Block Diagram ............................................................................................................................................... 9
4. Pin Descriptions .......................................................................................................................................... 10
5. Pad Arrangement and Coordination............................................................................................................ 14
6. Block Description ........................................................................................................................................ 21
7. System Interface ......................................................................................................................................... 24
7.1.
Interface Specifications .................................................................................................................. 24
7.2.
Input Interfaces .............................................................................................................................. 25
7.2.1.
i80/18-bit System Interface.................................................................................................. 26
7.2.2.
i80/16-bit System Interface.................................................................................................. 27
7.2.3.
i80/9-bit System Interface.................................................................................................... 28
7.2.4.
i80/8-bit System Interface.................................................................................................... 28
7.3.
Serial Peripheral Interface (SPI) .................................................................................................... 29
7.4.
VSYNC Interface............................................................................................................................ 34
7.5.
RGB Input Interface ....................................................................................................................... 38
7.6.
7.5.1.
RGB Interface...................................................................................................................... 39
7.5.2.
RGB Interface Timing .......................................................................................................... 40
7.5.3.
Moving Picture Mode........................................................................................................... 42
7.5.4.
6-bit RGB Interface.............................................................................................................. 43
7.5.5.
16-bit RGB Interface............................................................................................................ 44
7.5.6.
18-bit RGB Interface............................................................................................................ 44
Interface Timing.............................................................................................................................. 47
8. Register Descriptions .................................................................................................................................. 48
8.1.
Registers Access............................................................................................................................ 48
8.2.
Instruction Descriptions.................................................................................................................. 51
8.2.1.
Index (IR)............................................................................................................................. 53
8.2.2.
Status Read (RS)................................................................................................................. 53
8.2.3.
Start Oscillation (R00h)........................................................................................................ 53
8.2.4.
Driver Output Control (R01h) .............................................................................................. 53
8.2.5.
LCD Driving Wave Control (R02h) ...................................................................................... 55
8.2.6.
Entry Mode (R03h) .............................................................................................................. 55
8.2.7.
Resizing Control Register (R04h)........................................................................................ 57
8.2.8.
Display Control 1 (R07h) ..................................................................................................... 58
8.2.9.
Display Control 2 (R08h) ..................................................................................................... 59
8.2.10. Display Control 3 (R09h) ..................................................................................................... 60
8.2.11. Display Control 4 (R0Ah)..................................................................................................... 61
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 2 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
8.2.12. RGB Display Interface Control 1 (R0Ch)............................................................................. 62
8.2.13. Frame Marker Position (R0Dh) ........................................................................................... 63
8.2.14. RGB Display Interface Control 2 (R0Fh) ............................................................................. 63
8.2.15. Power Control 1 (R10h)....................................................................................................... 64
8.2.16. Power Control 2 (R11h) ....................................................................................................... 65
8.2.17. Power Control 3 (R12h)....................................................................................................... 66
8.2.18. Power Control 4 (R13h)....................................................................................................... 66
8.2.19. GRAM Horizontal/Vertical Address Set (R20h, R21h) ........................................................ 67
8.2.20. Write Data to GRAM (R22h)................................................................................................ 67
8.2.21. Read Data from GRAM (R22h) ........................................................................................... 68
8.2.22. Power Control 7 (R29h)....................................................................................................... 69
8.2.23. Frame Rate and Color Control (R2Bh)................................................................................ 70
8.2.24. Gamma Control (R30h ~ R3Dh).......................................................................................... 71
8.2.25. Horizontal and Vertical RAM Address Position (R50h, R51h, R52h, R53h) ....................... 71
8.2.26. Gate Scan Control (R60h, R61h, R6Ah) ............................................................................. 72
8.2.27. Partial Image 1 Display Position (R80h).............................................................................. 75
8.2.28. Partial Image 1 RAM Start/End Address (R81h, R82h)....................................................... 75
8.2.29. Partial Image 2 Display Position (R83h).............................................................................. 75
8.2.30. Partial Image 2 RAM Start/End Address (R84h, R85h)....................................................... 75
8.2.31. Panel Interface Control 1 (R90h)......................................................................................... 75
8.2.32. Panel Interface Control 2 (R92h)......................................................................................... 76
8.2.33. Panel Interface Control 4 (R95h)......................................................................................... 76
8.2.34. OTP VCM Programming Control (RA1h) ............................................................................ 77
8.2.35. OTP VCM Status and Enable (RA2h) ................................................................................. 77
8.2.36. OTP Programming ID Key (RA5h) ...................................................................................... 78
9. OTP Programming Flow.............................................................................................................................. 79
10. GRAM Address Map & Read/Write ............................................................................................................. 82
11. Window Address Function........................................................................................................................... 88
12. Gamma Correction...................................................................................................................................... 90
13. Application................................................................................................................................................... 95
13.1. Configuration of Power Supply Circuit ........................................................................................... 95
13.2. Display ON/OFF Sequence ........................................................................................................... 97
13.3. Standby and Sleep Mode ............................................................................................................... 99
13.4. Power Supply Configuration ........................................................................................................ 100
13.5. Voltage Generation ...................................................................................................................... 101
13.6. Applied Voltage to the TFT panel................................................................................................. 102
13.7. Partial Display Function ............................................................................................................... 102
13.8. Resizing Function......................................................................................................................... 103
14. Electrical Characteristics........................................................................................................................... 106
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 3 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
14.1. Absolute Maximum Ratings ......................................................................................................... 106
14.2. DC Characteristics ....................................................................................................................... 107
14.3. Reset Timing Characteristics ....................................................................................................... 107
14.4. LCD Driver Output Characteristics............................................................................................... 107
14.5. AC Characteristics ....................................................................................................................... 108
14.5.1. i80-System Interface Timing Characteristics ..................................................................... 108
14.5.2. Serial Data Transfer Interface Timing Characteristics....................................................... 108
14.5.3. RGB Interface Timing Characteristics ............................................................................... 109
15. Revision History .........................................................................................................................................111
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 4 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
Figures
FIGURE1 SYSTEM INTERFACE AND RGB INTERFACE CONNECTION .................................................................................... 25
FIGURE2 18-BIT SYSTEM INTERFACE DATA FORMAT ......................................................................................................... 26
FIGURE3 16-BIT SYSTEM INTERFACE DATA FORMAT ......................................................................................................... 27
FIGURE4 9-BIT SYSTEM INTERFACE DATA FORMAT ........................................................................................................... 28
FIGURE5 8-BIT SYSTEM INTERFACE DATA FORMAT ........................................................................................................... 29
FIGURE6 DATA TRANSFER SYNCHRONIZATION IN 8/9-BIT SYSTEM INTERFACE.................................................................. 29
FIGURE 7 DATA FORMAT OF SPI INTERFACE ..................................................................................................................... 31
FIGURE8 DATA TRANSMISSION THROUGH SERIAL PERIPHERAL INTERFACE (SPI) ............................................................... 32
FIGURE9 DATA TRANSMISSION THROUGH SERIAL PERIPHERAL INTERFACE (SPI), TRI=”1” AND DFM=”10”).................... 33
FIGURE10 DATA TRANSMISSION THROUGH VSYNC INTERFACE)....................................................................................... 34
FIGURE11 MOVING PICTURE DATA TRANSMISSION THROUGH VSYNC INTERFACE ............................................................ 34
FIGURE12 OPERATION THROUGH VSYNC INTERFACE ...................................................................................................... 35
FIGURE13 TRANSITION FLOW BETWEEN VSYNC AND INTERNAL CLOCK OPERATION MODES ............................................ 37
FIGURE14 RGB INTERFACE DATA FORMAT ...................................................................................................................... 38
FIGURE15 GRAM ACCESS AREA BY RGB INTERFACE ..................................................................................................... 39
FIGURE16 TIMING CHART OF SIGNALS IN 18-/16-BIT RGB INTERFACE MODE .................................................................. 40
FIGURE17 TIMING CHART OF SIGNALS IN 6-BIT RGB INTERFACE MODE ............................................................................ 41
FIGURE18 EXAMPLE OF UPDATE THE STILL AND MOVING PICTURE .................................................................................... 42
FIGURE19 INTERNAL CLOCK OPERATION/RGB INTERFACE MODE SWITCHING ................................................................... 45
FIGURE20 GRAM ACCESS BETWEEN SYSTEM INTERFACE AND RGB INTERFACE .............................................................. 46
FIGURE21 RELATIONSHIP BETWEEN RGB I/F SIGNALS AND LCD DRIVING SIGNALS FOR PANEL ..................................... 47
FIGURE22 REGISTER SETTING WITH SERIAL PERIPHERAL INTERFACE (SPI)...................................................................... 48
FIGURE23 REGISTER SETTING WITH I80 SYSTEM INTERFACE ............................................................................................ 49
FIGURE 24 REGISTER READ/WRITE TIMING OF I80 SYSTEM INTERFACE ........................................................................... 50
FIGURE25 GRAM ACCESS DIRECTION SETTING ............................................................................................................... 56
FIGURE26 16-BIT MPU SYSTEM INTERFACE DATA FORMAT............................................................................................. 57
FIGURE27 8-BIT MPU SYSTEM INTERFACE DATA FORMAT............................................................................................... 57
FIGURE 28 DATA READ FROM GRAM THROUGH READ DATA REGISTER IN 18-/16-/9-/8-BIT INTERFACE MODE .............. 68
FIGURE 29 GRAM DATA READ BACK FLOW CHART ........................................................................................................ 69
FIGURE 30 GRAM ACCESS RANGE CONFIGURATION ........................................................................................................ 72
FIGURE31 GRAM READ/WRITE TIMING OF I80-SYSTEM INTERFACE ............................................................................... 82
FIGURE32 I80-SYSTEM INTERFACE WITH 18-/16-/9-BIT DATA BUS (SS=”0”, BGR=”0”) ................................................. 84
FIGURE33 I80-SYSTEM INTERFACE WITH 8-BIT DATA BUS (SS=”0”, BGR=”0”) .............................................................. 85
FIGURE 34 I80-SYSTEM INTERFACE WITH 18-/9-BIT DATA BUS (SS=”1”, BGR=”1”) ....................................................... 87
FIGURE 35 GRAM ACCESS WINDOW MAP ....................................................................................................................... 88
FIGURE 36 GRAYSCALE VOLTAGE GENERATION ............................................................................................................... 90
FIGURE 37 GRAYSCALE VOLTAGE ADJUSTMENT .............................................................................................................. 91
FIGURE 38 GAMMA CURVE ADJUSTMENT ......................................................................................................................... 92
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 5 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
FIGURE 39 RELATIONSHIP BETWEEN SOURCE OUTPUT AND VCOM ................................................................................. 94
FIGURE 40 RELATIONSHIP BETWEEN GRAM DATA AND OUTPUT LEVEL.......................................................................... 94
FIGURE 41 POWER SUPPLY CIRCUIT BLOCK ...................................................................................................................... 95
FIGURE 42 DISPLAY ON/OFF REGISTER SETTING SEQUENCE ............................................................................................ 99
FIGURE 43 STANDBY/SLEEP MODE REGISTER SETTING SEQUENCE................................................................................... 99
FIGURE 44 POWER SUPPLY ON/OFF SEQUENCE ............................................................................................................. 100
FIGURE 45 VOLTAGE CONFIGURATION DIAGRAM ........................................................................................................... 101
FIGURE 46 VOLTAGE OUTPUT TO TFT LCD PANEL ........................................................................................................ 102
FIGURE 47 PARTIAL DISPLAY EXAMPLE .......................................................................................................................... 103
FIGURE 48 DATA TRANSFER IN RESIZING ......................................................................................................................... 104
FIGURE 49 RESIZING EXAMPLE ....................................................................................................................................... 104
FIGURE 50 I80-SYSTEM BUS TIMING ............................................................................................................................... 108
FIGURE 51 SPI SYSTEM BUS TIMING ............................................................................................................................... 109
FIGURE52 RGB INTERFACE TIMING ................................................................................................................................ 110
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 6 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
1. Introduction
ILI9325 is a 262,144-color one-chip SoC driver for a-TFT liquid crystal display with resolution of 240RGBx320
dots, comprising a 720-channel source driver, a 320-channel gate driver, 172,800 bytes RAM for graphic data
of 240RGBx320 dots, and power supply circuit.
ILI9325 has four kinds of system interfaces which are i80-system MPU interface (8-/9-/16-/18-bit bus width),
VSYNC interface (system interface + VSYNC, internal clock, DB[17:0]), serial data transfer interface (SPI)
and RGB 6-/16-/18-bit interface (DOTCLK, VSYNC, HSYNC, ENABLE, DB[17:0]).
In RGB interface and VSYNC interface mode, the combined use of high-speed RAM write function and widow
address function enables to display a moving picture at a position specified by a user and still pictures in other
areas on the screen simultaneously, which makes it possible to transfer display the refresh data only to
minimize data transfers and power consumption.
ILI9325 can operate with 1.65V I/O interface voltage, and an incorporated voltage follower circuit to generate
voltage levels for driving an LCD. The ILI9325 also supports a function to display in 8 colors and a sleep mode,
allowing for precise power control by software and these features make the ILI9325 an ideal LCD driver for
medium or small size portable products such as digital cellular phones, smart phone, PDA and PMP where
long battery life is a major concern.
2. Features
‹ Single chip solution for a liquid crystal QVGA TFT LCD display
‹ 240RGBx320-dot resolution capable with real 262,144 display color
‹ Support MVA (Multi-domain Vertical Alignment) wide view display
‹ Incorporate 720-channel source driver and 320-channel gate driver
‹ Internal 172,800 bytes graphic RAM
‹ High-speed RAM burst write function
‹ System interfaces
¾ i80 system interface with 8-/ 9-/16-/18-bit bus width
¾ Serial Peripheral Interface (SPI)
¾ RGB interface with 6-/16-/18-bit bus width (VSYNC, HSYNC, DOTCLK, ENABLE, DB[17:0])
¾ VSYNC interface (System interface + VSYNC)
‹ Internal oscillator and hardware reset
‹ Resizing function (×1/2, ×1/4)
‹ Reversible source/gate driver shift direction
‹ Window address function to specify a rectangular area for internal GRAM access
‹ Bit operation function for facilitating graphics data processing
¾ Bit-unit write data mask function
¾ Pixel-unit logical/conditional write function
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 7 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
‹ Abundant functions for color display control
¾ γ-correction function enabling display in 262,144 colors
¾ Line-unit vertical scrolling function
‹ Partial drive function, enabling partially driving an LCD panel at positions specified by user
‹ Incorporate step-up circuits for stepping up a liquid crystal drive voltage level up to 6 times (x6)
‹ Power saving functions
¾ 8-color mode
¾ standby mode
¾ sleep mode
‹ Low -power consumption architecture
¾ Low operating power supplies:
ƒ IOVcc = 1.65V ~ 3.3 V (interface I/O)
ƒ Vcc = 2.4V ~ 3.3 V (internal logic)
ƒ Vci = 2.5V ~ 3.3 V (analog)
‹ LCD Voltage drive:
¾ Source/VCOM power supply voltage
ƒ DVDH - GND = 4.5V ~ 6.0
ƒ VCL – GND = -2.0V ~ -3.0V
ƒ VCI – VCL ≦ 6.0V
¾ Gate driver output voltage
ƒ VGH - GND = 10V ~ 20V
ƒ VGL – GND = -5V ~ -15V
ƒ VGH – VGL ≦ 32V
¾ VCOM driver output voltage
ƒ VCOMH = 3.0V ~ (DDVDH-0.5)V
ƒ VCOML = (VCL+0.5)V ~ 0V
ƒ VCOMH-VCOML ≦ 6.0V
‹ a-TFT LCD storage capacitor: Cst only
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 8 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
3. Block Diagram
IOVCC
Index
Register
(IR)
IM[3:0]
nRESET
nCS
nWR/SCL
nRD
RS
SDI
SDO
DB[17:0]
HSYNC
VSYNC
DOTCLK
ENABLE
TEST1
MPU I/F
18-bit
16-bit
9-bit
8-bit
7
Control
Register
(CR)
18
LCD
Source
Driver
SPI I/F
RGB I/F
18-bit
16-bit
6-bit
Graphics
Operation
18
S[720:1]
18
V63 ~ 0
VSYNC I/F
Read
Latch
18
TEST2
TEST3
TS[8:0]
Write
Latch
72
Grayscale
Reference
Voltage
72
Graphics RAM
(GRAM)
VCC
VDDD
Address
Counter
(AC)
Regulator
VREG1OUT
VGS
DUMMY20~27
GND
DUMMY1~15
LCD
Gate
Driver
Timing
Controller
RC-OSC.
G[320:1]
VCI
C22-
VGH
VGL
C21-
C22+
C21+
VCL
C13-
C12-
C13+
C12+
C11-
DDVDH
C11+
GND
VCOM
VCOML
VCOM
Generator
Charge-pump Power Circuit
VCOMH
VCI1
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 9 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
4. Pin Descriptions
Pin Name
IM3,
IM2,
IM1,
IM0/ID
I/O
I
Type
IOVcc
nCS
I
MPU
IOVcc
RS
I
MPU
IOVcc
nWR/SCL
I
MPU
IOVcc
nRD
I
MPU
IOVcc
nRESET
I
MPU
IOVcc
SDI
I
MPU
IOVcc
SDO
O
MPU
IOVcc
DB[17:0]
I/O
MPU
IOVcc
Descriptions
Input Interface
Select the MPU system interface mode
IM3
IM2
IM1
IM0
MPU-Interface Mode
0
0
0
0
Setting invalid
0
0
0
1
Setting invalid
0
0
1
0
i80-system 16-bit interface
DB Pin in use
DB[17:10], DB[8:1]
0
0
1
1
i80-system 8-bit interface
DB[17:10]
0
1
0
ID
Serial Peripheral Interface (SPI)
SDI, SDO
0
1
1
*
Setting invalid
1
0
0
0
Setting invalid
1
0
0
1
Setting invalid
1
0
1
0
i80-system 18-bit interface
DB[17:0]
1
0
1
1
i80-system 9-bit interface
DB[17:9]
1
1
*
*
Setting invalid
When the serial peripheral interface is selected, IM0 pin is used for
the device code ID setting.
A chip select signal.
Low: the ILI9325 is selected and accessible
High: the ILI9325 is not selected and not accessible
Fix to the DGND level when not in use.
A register select signal.
Low: select an index or status register
High: select a control register
Fix to either IOVcc or DGND level when not in use.
A write strobe signal and enables an operation to write data when the
signal is low.
Fix to either IOVcc or DGND level when not in use.
SPI Mode:
Synchronizing clock signal in SPI mode.
A read strobe signal and enables an operation to read out data when
the signal is low.
Fix to either IOVcc or DGND level when not in use.
A reset pin.
Initializes the ILI9325 with a low input. Be sure to execute a power-on
reset after supplying power.
SPI interface input pin.
The data is latched on the rising edge of the SCL signal.
SPI interface output pin.
The data is outputted on the falling edge of the SCL signal.
Let SDO as floating when not used.
An 18-bit parallel bi-directional data bus for MPU system interface
mode
8-bit I/F: DB[17:10] is used.
9-bit I/F: DB[17:9] is used.
16-bit I/F: DB[17:10] and DB[8:1] is used.
18-bit I/F: DB[17:0] is used.
18-bit parallel bi-directional data bus for RGB interface operation
6-bit RGB I/F: DB[17:12] are used.
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 10 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
Pin Name
ENABLE
I/O
I
Type
MPU
IOVcc
DOTCLK
I
MPU
IOVcc
VSYNC
I
MPU
IOVcc
HSYNC
I
MPU
IOVcc
FMARK
O
MPU
IOVcc
S720~S1
O
LCD
G320~G1
O
LCD
VCOM
O
VCOMH
O
VCOML
O
VGS
I
Vci
I
GND
I
Vci1
O
DDVDH
O
ILI9325
Descriptions
16-bit RGB I/F: DB[17:13] and DB[11:1] are used.
18-bit RGB I/F: DB[17:0] are used.
Unused pins must be fixed to DGND level.
Data ENEABLE signal for RGB interface operation.
Low: Select (access enabled)
High: Not select (access inhibited)
The EPL bit inverts the polarity of the ENABLE signal.
Fix to either IOVcc or DGND level when not in use.
Dot clock signal for RGB interface operation.
DPL = “0”: Input data on the rising edge of DOTCLK
DPL = “1”: Input data on the falling edge of DOTCLK
Fix to the DGND level when not in use
Frame synchronizing signal for RGB interface operation.
VSPL = “0”: Active low.
VSPL = “1”: Active high.
Fix to the DGND level when not in use.
Line synchronizing signal for RGB interface operation.
HSPL = “0”: Active low.
HSPL = “1”: Active high.
Fix to the DGND level when not in use
Output a frame head pulse signal.
The FMARK signal is used when writing RAM data in synchronization
with frame. Leave the pin open when not in use.
LCD Driving signals
Source output voltage signals applied to liquid crystal.
To change the shift direction of signal outputs, use the SS bit.
SS = “0”, the data in the RAM address “h00000” is output from S1.
SS = “1”, the data in the RAM address “h00000” is output from S720.
S1, S4, S7, … display red (R), S2, S5, S8, ... display green (G), and
S3, S6, S9, ... display blue (B) (SS = 0).
Gate line output signals.
VGH: the level selecting gate lines
VGL: the level not selecting gate lines
A supply voltage to the common electrode of TFT panel.
VCOM is AC voltage alternating signal between the VCOMH and
VCOML levels.
The high level of VCOM AC voltage. Connect to a stabilizing
capacitor.
The low level of VCOM AC voltage. Adjust the VCOML level with the
VDV bits. Connect to a stabilizing capacitor.
TFT
common
electrode
Stabilizing
capacitor
Stabilizing
capacitor
GND or
Reference level for the grayscale voltage generating circuit. The VGS
external
level can be changed by connecting to an external resistor.
resistor
Charge-pump and Regulator Circuit
Power
A supply voltage to the analog circuit. Connect to an external power
supply
supply of 2.5 ~ 3.3V.
Power
GND for the analog side: GND = 0V. In case of COG, connect to
supply
GND on the FPC to prevent noise.
An internal reference voltage for the step-up circuit1.
The amplitude between Vci and DGND is determined by the VC[2:0]
Stabilizing
bits.
capacitor
Make sure to set the Vci1 voltage so that the DDVDH, VGH and VGL
voltages are set within the respective specification.
Stabilizing Power supply for the source driver and Vcom drive.
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 11 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
Pin Name
I/O
Type
capacitor
Stabilizing
capacitor
Stabilizing
capacitor
Descriptions
VGH
I
VGL
I
VCL
O
Stabilizing
capacitor
I/O
Step-up
capacitor
Capacitor connection pins for the step-up circuit 1.
I/O
Step-up
capacitor
Capacitor connection pins for the step-up circuit 2.
C11+, C11C12+, C12C13+, C13C21+, C21C22+, C22-
ILI9325
Power supply for the gate driver.
Power supply for the gate driver.
VcomL driver power supply.
VCL = 0.5 ~ –VCI . Place a stabilizing capacitor between GND
Output voltage generated from the reference voltage.
VREG1OUT
Vcc
I/O
Stabilizing
capacitor
I
Power
supply
IOVcc
I
Power
supply
VDDD
O
Power
GND
I
Power
supply
The voltage level is set with the VRH bits.
VREG1OUT is (1) a source driver grayscale reference voltage, (2)
VcomH level reference voltage, and (3) Vcom amplitude reference
voltage. Connect to a stabilizing capacitor. VREG1OUT = 3.0 ~
(DDVDH – 0.5)V.
Power Pads
A supply voltage to the internal logic: Vcc = 2.4~3.3V
A supply voltage to the interface pins:
IM[3:0], nRESET, nCS, nWR, nRD, RS, DB[17:0], VSYNC, HSYNC,
DOTCLK, ENABLE, SCL, SDI, SDO.
IOVcc = 1.65 ~ 3.3V and Vcc ≧IOVcc. In case of COG, connect to
Vcc on the FPC if IOVcc=Vcc, to prevent noise.
Digital circuit power pad.
Connect these pins with the 1uF capacitor.
GND for the analog side: DGND = 0V.
Test Pads
Dummy pad.
Leave these pins as open.
DUMMY1~ 15
DUMMY20 ~ 27
-
-
IOGNDDUM
O
GND
GND pin.
TESTO1~16
O
Open
TEST1, 2, 3
I
IOGND
TS0~8
I
OPEN
Test pins. Leave them open.
Test pins (internal pull low).
Connect to GND or leave these pins as open.
Test pins (internal pull low). Leave them open.
Liquid crystal power supply specifications Table 1
No.
1
2
3
4
Item
TFT Source Driver
TFT Gate Driver
TFT Display’s Capacitor Structure
S1 ~ S720
Liquid
Crystal
Drive
G1 ~ G320
Output
VCOM
Description
720 pins (240 x RGB)
320 pins
Cst structure only (Common VCOM)
V0 ~ V63 grayscales
VGH - VGL
VCOMH - VCOML: Amplitude = electronic volumes
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 12 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
5
Input Voltage
6
Liquid
Crystal
Voltages
7
Internal Step-up Circuits
Drive
IOVcc
Vcc
Vci
DDVDH
VGH
VGL
VCL
VGH - VGL
Vci - VCL
DDVDH
VGH
VGL
VCL
ILI9325
1.65 ~ 3.30V
2.40 ~ 3.30V
2.50 ~ 3.30V
4.5V ~ 6.0V
10V ~ 20V
-5V ~ -15V
-1.9V ~ -3.0V
Max. 32V
Max. 6.0V
Vci1 x2
Vci1 x4, x5, x6
Vci1 x-3, x-4, x-5
Vci1 x-1
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 13 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
5. Pad Arrangement and Coordination
Chip Size: 17820um x 870um
VCOM
VCOM
VCOM
VCOM
VCOMH
VCOMH
VCOMH
VCOMH
VCOMH
VCOMH
1
2
0
VCI
VCI
VCI
VCI
VCI
VCI
VCI
VCI
VCI
VCI
1
6
0
VCI
VCI
DUMMY10
DUMMY11
C12C12C12C12C12C12+
1
7
0
C12+
C12+
C12+
C12+
C11C11C11C11C11C11+
1
8
0
…………………….
DUMMY23
S361
S362
S363
S364
S365
S366
S367
S368
S369
…………………….
1
5
0
1
9
0
2
0
0
S712
S713
S714
S715
S716
S717
S718
S719
S720
DUMMY22
VGH
VGH
VGH
DUMMY12
DUMMY13
C13C13C13C13C13+
2
1
0
C13+
C13+
C13+
C21C21C21C21C21C21C21-
2
2
0
C21+
C21+
C21+
C21+
C21+
C21+
C21+
C22C22C22-
2
3
0
C22C22C22C22C22+
C22+
C22+
C22+
C22+
C22+
2
4
0
C22+
DUMMY14
DUMMY15
DUMMY21
G2
G4
G6
G8
G10
G12
G14
G16
G18
…………
15
2
4
3
Bump View
y
DDVDH
VCI1
VCI1
VCI1
VCI
VCI
VCI
VCI
VCI
VCI
VGL
VGL
VGL
VGL
GND
GND
GND
VGH
VGH
VGH
Alignment Mark: A2
S353
S354
S355
S356
S357
S358
S359
S360
DUMMY24
x
VCL
VCL
VCL
VCL
VCL
DDVDH
DDVDH
DDVDH
DDVDH
DDVDH
1
4
0
20
1
3
0
15
5
VCOML
VCOML
VCOML
VCOML
VREG1OUT
VREG1OUT
VREG1OUT
DUMMY7
DUMMY8
DUMMY9
C11+
C11+
C11+
C11+
VGL
VGL
VGL
VGL
VGL
VGL
…………
GND
GND
GND
GND
DUMMY4
DUMMY5
DUMMY6
VCOM
VCOM
VCOM
1
1
0
15
10
1
0
0
20
15
DUMMY25
S1
S2
S3
S4
S5
S6
S7
S8
S9
Face Up
(Bump View)
9
0
15
5
Alignment Mark: A1
20
VDDD
VDDD
VDDD
DUMMY3
GND
GND
GND
GND
GND
GND
GND
GND
VGS
VGS
GND
GND
GND
GND
GND
GND
15
10
15
IOVCC
IOVCC
VDDD
VDDD
VDDD
VDDD
VDDD
VDDD
VDDD
VDDD
8
0
20
TS4
TS3
TS2
TS1
TS0
DUMMY2
IOVCC
IOVCC
IOVCC
IOVCC
7
0
Alignment Marks
G17
G15
G13
G11
G9
G7
G5
G3
G1
DUMMY26
6
0
RS
nCS
TESTO14
TESTO15
FMARK
TESTO16
TS8
TS7
TS6
TS5
2. 50um x 80um
Input Pads
Pad 1 to 243.
15
DB4
DB3
DB2
DB1
DB0
TESTO13
SDO
SDI
nRD
nWR/SCL
5
0
1. 16um x 98um
Gate: G1 ~ G320
Source: S1 ~ S720
DB12
DB11
DB10
DB9
DB8
TEST3
TESTO12
DB7
DB6
DB5
4
0
Au Bump Size:
VSYNC
HSYNC
DOTCLK
ENABLE
DB17
DB16
DB15
DB14
DB13
TESTO11
3
0
Au bump height: 15um (typ.)
TEST2
TESTO4
TESTO5
TESTO6
TESTO7
TESTO8
TESTO9
TESTO10
nRESET
nRESET
2
0
Coordinate Origin: Chip center
DUMMY1
TEST1
IOGNDDUM
TESTO1
TESTO2
TESTO3
IM0/ID
IM1
IM2
IM3
1
0
Pad Location: Pad Center.
DUMMY27
G319
G317
G315
G313
G311
G309
G307
G305
G303
1
Chip thickness : 400um or 280um (typ.)
G304
G306
G308
G310
G312
G314
G316
G318
G320
DUMMY20
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 14 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
X
Y
X
ILI9325
No.
Name
X
Y
No.
Name
No.
Name
X
Y
No.
Name
No.
Name
X
Y
1
DUMMY1
-8610
-307.5
61
TS4
-4130 -307.5
121
VCOML
70
-307.5
181
C11+
4270 -307.5
Y
241
C22+
8470
-307.5
2
TEST1
-8540
-307.5
62
TS3
-4060 -307.5
122
VCOML
140
-307.5
182
C11+
4340 -307.5
242 DUMMY14
8540
-307.5
3
IOGNDDUM
-8470
-307.5
63
TS2
-3990 -307.5
123
VCOML
210
-307.5
183
C11+
4410 -307.5
243 DUMMY15
8610
-307.5
4
TESTO1
-8400
-307.5
64
TS1
-3920 -307.5
124
VCOML
280
-307.5
184
C11+
4480 -307.5
244 DUMMY20
8659
202.5
5
TESTO2
-8330
-307.5
65
TS0
-3850 -307.5
125 VREG1OUT
350
-307.5
185
VGL
4550 -307.5
245
G320
8643
319.5
6
TESTO3
-8260
-307.5
66
DUMMY2
-3780 -307.5
126 VREG1OUT
420
-307.5
186
VGL
4620 -307.5
246
G318
8627
202.5
7
IM0/ID
-8190
-307.5
67
IOVCC
-3710 -307.5
127 VREG1OUT
490
-307.5
187
VGL
4690 -307.5
247
G316
8611
319.5
8
IM1
-8120
-307.5
68
IOVCC
-3640 -307.5
128
DUMMY7
560
-307.5
188
VGL
4760 -307.5
248
G314
8595
202.5
9
IM2
-8050
-307.5
69
IOVCC
-3570 -307.5
129
DUMMY8
630
-307.5
189
VGL
4830 -307.5
249
G312
8579
319.5
10
IM3
-7980
-307.5
70
IOVCC
-3500 -307.5
130
DUMMY9
700
-307.5
190
VGL
4900 -307.5
250
G310
8563
202.5
11
TEST2
-7910
-307.5
71
IOVCC
-3430 -307.5
131
VCL
770
-307.5
191
VGL
4970 -307.5
251
G308
8547
319.5
12
TESTO4
-7840
-307.5
72
IOVCC
-3360 -307.5
132
VCL
840
-307.5
192
VGL
5040 -307.5
252
G306
8531
202.5
13
TESTO5
-7770
-307.5
73
VDDD
-3290 -307.5
133
VCL
910
-307.5
193
VGL
5110 -307.5
253
G304
8515
319.5
14
TESTO6
-7700
-307.5
74
VDDD
-3220 -307.5
134
VCL
980
-307.5
194
VGL
5180 -307.5
254
G302
8499
202.5
15
TESTO7
-7630
-307.5
75
VDDD
-3150 -307.5
135
VCL
1050
-307.5
195
GND
5250 -307.5
255
G300
8483
319.5
16
TESTO8
-7560
-307.5
76
VDDD
-3080 -307.5
136
DDVDH
1120
-307.5
196
GND
5320 -307.5
256
G298
8467
202.5
17
TESTO9
-7490
-307.5
77
VDDD
-3010 -307.5
137
DDVDH
1190
-307.5
197
GND
5390 -307.5
257
G296
8451
319.5
18
TESTO10
-7420
-307.5
78
VDDD
-2940 -307.5
138
DDVDH
1260
-307.5
198
VGH
5460 -307.5
258
G294
8435
202.5
19
nRESET
-7350
-307.5
79
VDDD
-2870 -307.5
139
DDVDH
1330
-307.5
199
VGH
5530 -307.5
259
G292
8419
319.5
20
nRESET
-7280
-307.5
80
VDDD
-2800 -307.5
140
DDVDH
1400
-307.5
200
VGH
5600 -307.5
260
G290
8403
202.5
21
VSYNC
-7210
-307.5
81
VDDD
-2730 -307.5
141
DDVDH
1470
-307.5
201
VGH
5670 -307.5
261
G288
8387
319.5
22
HSYNC
-7140
-307.5
82
VDDD
-2660 -307.5
142
VCI1
1540
-307.5
202
VGH
5740 -307.5
262
G286
8371
202.5
23
DOTCLK
-7070
-307.5
83
VDDD
-2590 -307.5
143
VCI1
1610
-307.5
203
VGH
5810 -307.5
263
G284
8355
319.5
24
ENABLE
-7000
-307.5
84
DUMMY3
-2520 -307.5
144
VCI1
1680
-307.5
204 DUMMY12
5880 -307.5
264
G282
8339
202.5
25
DB17
-6905
-307.5
85
GND
-2450 -307.5
145
VCI
1750
-307.5
205 DUMMY13
5950 -307.5
265
G280
8323
319.5
26
DB16
-6825
-307.5
86
GND
-2380 -307.5
146
VCI
1820
-307.5
206
C13-
6020 -307.5
266
G278
8307
202.5
27
DB15
-6745
-307.5
87
GND
-2310 -307.5
147
VCI
1890
-307.5
207
C13-
6090 -307.5
267
G276
8291
319.5
28
DB14
-6665
-307.5
88
GND
-2240 -307.5
148
VCI
1960
-307.5
208
C13-
6160 -307.5
268
G274
8275
202.5
29
DB13
-6585
-307.5
89
GND
-2170 -307.5
149
VCI
2030
-307.5
209
C13-
6230 -307.5
269
G272
8259
319.5
30
TESTO11
-6495
-307.5
90
GND
-2100 -307.5
150
VCI
2100
-307.5
210
C13+
6300 -307.5
270
G270
8243
202.5
31
DB12
-6405
-307.5
91
GND
-2030 -307.5
151
VCI
2170
-307.5
211
C13+
6370 -307.5
271
G268
8227
319.5
32
DB11
-6325
-307.5
92
GND
-1960 -307.5
152
VCI
2240
-307.5
212
C13+
6440 -307.5
272
G266
8211
202.5
33
DB10
-6245
-307.5
93
VGS
-1890 -307.5
153
VCI
2310
-307.5
213
C13+
6510 -307.5
273
G264
8195
319.5
34
DB9
-6165
-307.5
94
VGS
-1820 -307.5
154
VCI
2380
-307.5
214
C21-
6580 -307.5
274
G262
8179
202.5
35
DB8
-6085
-307.5
95
GND
-1750 -307.5
155
VCI
2450
-307.5
215
C21-
6650 -307.5
275
G260
8163
319.5
36
TEST3
-5990
-307.5
96
GND
-1680 -307.5
156
VCI
2520
-307.5
216
C21-
6720 -307.5
276
G258
8147
202.5
37
TESTO12
-5920
-307.5
97
GND
-1610 -307.5
157
VCI
2590
-307.5
217
C21-
6790 -307.5
277
G256
8131
319.5
38
DB7
-5825
-307.5
98
GND
-1540 -307.5
158
VCI
2660
-307.5
218
C21-
6860 -307.5
278
G254
8115
202.5
39
DB6
-5745
-307.5
99
GND
-1470 -307.5
159
VCI
2730
-307.5
219
C21-
6930 -307.5
279
G252
8099
319.5
40
DB5
-5665
-307.5
100
GND
-1400 -307.5
160
VCI
2800
-307.5
220
C21-
7000 -307.5
280
G250
8083
202.5
41
DB4
-5585
-307.5
101
GND
-1330 -307.5
161
VCI
2870
-307.5
221
C21+
7070 -307.5
281
G248
8067
319.5
42
DB3
-5505
-307.5
102
GND
-1260 -307.5
162
VCI
2940
-307.5
222
C21+
7140 -307.5
282
G246
8051
202.5
43
DB2
-5425
-307.5
103
GND
-1190 -307.5
163 DUMMY10
3010
-307.5
223
C21+
7210 -307.5
283
G244
8035
319.5
44
DB1
-5345
-307.5
104
GND
-1120 -307.5
164 DUMMY11
3080
-307.5
224
C21+
7280 -307.5
284
G242
8019
202.5
45
DB0
-5265
-307.5
105
DUMMY4
-1050 -307.5
165
C12-
3150
-307.5
225
C21+
7350 -307.5
285
G240
8003
319.5
46
TESTO13
-5180
-307.5
106
DUMMY5
-980
-307.5
166
C12-
3220
-307.5
226
C21+
7420 -307.5
286
G238
7987
202.5
47
SDO
-5110
-307.5
107
DUMMY6
-910
-307.5
167
C12-
3290
-307.5
227
C21+
7490 -307.5
287
G236
7971
319.5
48
SDI
-5040
-307.5
108
VCOM
-840
-307.5
168
C12-
3360
-307.5
228
C22-
7560 -307.5
288
G234
7955
202.5
49
nRD
-4970
-307.5
109
VCOM
-770
-307.5
169
C12-
3430
-307.5
229
C22-
7630 -307.5
289
G232
7939
319.5
50
nWR/SCL
-4900
-307.5
110
VCOM
-700
-307.5
170
C12+
3500
-307.5
230
C22-
7700 -307.5
290
G230
7923
202.5
51
RS
-4830
-307.5
111
VCOM
-630
-307.5
171
C12+
3570
-307.5
231
C22-
7770 -307.5
291
G228
7907
319.5
52
nCS
-4760
-307.5
112
VCOM
-560
-307.5
172
C12+
3640
-307.5
232
C22-
7840 -307.5
292
G226
7891
202.5
53
TESTO14
-4690
-307.5
113
VCOM
-490
-307.5
173
C12+
3710
-307.5
233
C22-
7910 -307.5
293
G224
7875
319.5
54
TESTO15
-4620
-307.5
114
VCOM
-420
-307.5
174
C12+
3780
-307.5
234
C22-
7980 -307.5
294
G222
7859
202.5
55
FMARK
-4550
-307.5
115
VCOMH
-350
-307.5
175
C11-
3850
-307.5
235
C22+
8050 -307.5
295
G220
7843
319.5
56
TESTO16
-4480
-307.5
116
VCOMH
-280
-307.5
176
C11-
3920
-307.5
236
C22+
8120 -307.5
296
G218
7827
202.5
57
TS8
-4410
-307.5
117
VCOMH
-210
-307.5
177
C11-
3990
-307.5
237
C22+
8190 -307.5
297
G216
7811
319.5
58
TS7
-4340
-307.5
118
VCOMH
-140
-307.5
178
C11-
4060
-307.5
238
C22+
8260 -307.5
298
G214
7795
202.5
59
TS6
-4270
-307.5
119
VCOMH
-70
-307.5
179
C11-
4130
-307.5
239
C22+
8330 -307.5
299
G212
7779
319.5
60
TS5
-4200
-307.5
120
VCOMH
0
-307.5
180
C11+
4200
-307.5
240
C22+
8400 -307.5
300
G210
7763
202.5
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 15 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
No.
Name
X
Y
No.
Name
X
Y
No.
Name
X
Y
No.
Name
X
Y
No.
Name
X
Y
301
G208
7747
319.5
361
G88
6787
319.5
421
S706
5807
202.5
481
S646
4847
202.5
541
S586
3887
202.5
302
G206
7731
202.5
362
G86
6771
202.5
422
S705
5791
319.5
482
S645
4831
319.5
542
S585
3871
319.5
303
G204
7715
319.5
363
G84
6755
319.5
423
S704
5775
202.5
483
S644
4815
202.5
543
S584
3855
202.5
304
G202
7699
202.5
364
G82
6739
202.5
424
S703
5759
319.5
484
S643
4799
319.5
544
S583
3839
319.5
305
G200
7683
319.5
365
G80
6723
319.5
425
S702
5743
202.5
485
S642
4783
202.5
545
S582
3823
202.5
306
G198
7667
202.5
366
G78
6707
202.5
426
S701
5727
319.5
486
S641
4767
319.5
546
S581
3807
319.5
307
G196
7651
319.5
367
G76
6691
319.5
427
S700
5711
202.5
487
S640
4751
202.5
547
S580
3791
202.5
308
G194
7635
202.5
368
G74
6675
202.5
428
S699
5695
319.5
488
S639
4735
319.5
548
S579
3775
319.5
309
G192
7619
319.5
369
G72
6659
319.5
429
S698
5679
202.5
489
S638
4719
202.5
549
S578
3759
202.5
310
G190
7603
202.5
370
G70
6643
202.5
430
S697
5663
319.5
490
S637
4703
319.5
550
S577
3743
319.5
311
G188
7587
319.5
371
G68
6627
319.5
431
S696
5647
202.5
491
S636
4687
202.5
551
S576
3727
202.5
312
G186
7571
202.5
372
G66
6611
202.5
432
S695
5631
319.5
492
S635
4671
319.5
552
S575
3711
319.5
313
G184
7555
319.5
373
G64
6595
319.5
433
S694
5615
202.5
493
S634
4655
202.5
553
S574
3695
202.5
314
G182
7539
202.5
374
G62
6579
202.5
434
S693
5599
319.5
494
S633
4639
319.5
554
S573
3679
319.5
315
G180
7523
319.5
375
G60
6563
319.5
435
S692
5583
202.5
495
S632
4623
202.5
555
S572
3663
202.5
316
G178
7507
202.5
376
G58
6547
202.5
436
S691
5567
319.5
496
S631
4607
319.5
556
S571
3647
319.5
317
G176
7491
319.5
377
G56
6531
319.5
437
S690
5551
202.5
497
S630
4591
202.5
557
S570
3631
202.5
318
G174
7475
202.5
378
G54
6515
202.5
438
S689
5535
319.5
498
S629
4575
319.5
558
S569
3615
319.5
319
G172
7459
319.5
379
G52
6499
319.5
439
S688
5519
202.5
499
S628
4559
202.5
559
S568
3599
202.5
320
G170
7443
202.5
380
G50
6483
202.5
440
S687
5503
319.5
500
S627
4543
319.5
560
S567
3583
319.5
321
G168
7427
319.5
381
G48
6467
319.5
441
S686
5487
202.5
501
S626
4527
202.5
561
S566
3567
202.5
322
G166
7411
202.5
382
G46
6451
202.5
442
S685
5471
319.5
502
S625
4511
319.5
562
S565
3551
319.5
323
G164
7395
319.5
383
G44
6435
319.5
443
S684
5455
202.5
503
S624
4495
202.5
563
S564
3535
202.5
324
G162
7379
202.5
384
G42
6419
202.5
444
S683
5439
319.5
504
S623
4479
319.5
564
S563
3519
319.5
325
G160
7363
319.5
385
G40
6403
319.5
445
S682
5423
202.5
505
S622
4463
202.5
565
S562
3503
202.5
326
G158
7347
202.5
386
G38
6387
202.5
446
S681
5407
319.5
506
S621
4447
319.5
566
S561
3487
319.5
327
G156
7331
319.5
387
G36
6371
319.5
447
S680
5391
202.5
507
S620
4431
202.5
567
S560
3471
202.5
328
G154
7315
202.5
388
G34
6355
202.5
448
S679
5375
319.5
508
S619
4415
319.5
568
S559
3455
319.5
329
G152
7299
319.5
389
G32
6339
319.5
449
S678
5359
202.5
509
S618
4399
202.5
569
S558
3439
202.5
330
G150
7283
202.5
390
G30
6323
202.5
450
S677
5343
319.5
510
S617
4383
319.5
570
S557
3423
319.5
331
G148
7267
319.5
391
G28
6307
319.5
451
S676
5327
202.5
511
S616
4367
202.5
571
S556
3407
202.5
332
G146
7251
202.5
392
G26
6291
202.5
452
S675
5311
319.5
512
S615
4351
319.5
572
S555
3391
319.5
333
G144
7235
319.5
393
G24
6275
319.5
453
S674
5295
202.5
513
S614
4335
202.5
573
S554
3375
202.5
334
G142
7219
202.5
394
G22
6259
202.5
454
S673
5279
319.5
514
S613
4319
319.5
574
S553
3359
319.5
335
G140
7203
319.5
395
G20
6243
319.5
455
S672
5263
202.5
515
S612
4303
202.5
575
S552
3343
202.5
336
G138
7187
202.5
396
G18
6227
202.5
456
S671
5247
319.5
516
S611
4287
319.5
576
S551
3327
319.5
337
G136
7171
319.5
397
G16
6211
319.5
457
S670
5231
202.5
517
S610
4271
202.5
577
S550
3311
202.5
338
G134
7155
202.5
398
G14
6195
202.5
458
S669
5215
319.5
518
S609
4255
319.5
578
S549
3295
319.5
339
G132
7139
319.5
399
G12
6179
319.5
459
S668
5199
202.5
519
S608
4239
202.5
579
S548
3279
202.5
340
G130
7123
202.5
400
G10
6163
202.5
460
S667
5183
319.5
520
S607
4223
319.5
580
S547
3263
319.5
341
G128
7107
319.5
401
G8
6147
319.5
461
S666
5167
202.5
521
S606
4207
202.5
581
S546
3247
202.5
342
G126
7091
202.5
402
G6
6131
202.5
462
S665
5151
319.5
522
S605
4191
319.5
582
S545
3231
319.5
343
G124
7075
319.5
403
G4
6115
319.5
463
S664
5135
202.5
523
S604
4175
202.5
583
S544
3215
202.5
344
G122
7059
202.5
404
G2
6099
202.5
464
S663
5119
319.5
524
S603
4159
319.5
584
S543
3199
319.5
345
G120
7043
319.5
405
DUMMY21
6083
319.5
465
S662
5103
202.5
525
S602
4143
202.5
585
S542
3183
202.5
346
G118
7027
202.5
406
DUMMY22
6047
319.5
466
S661
5087
319.5
526
S601
4127
319.5
586
S541
3167
319.5
347
G116
7011
319.5
407
S720
6031
202.5
467
S660
5071
202.5
527
S600
4111
202.5
587
S540
3151
202.5
348
G114
6995
202.5
408
S719
6015
319.5
468
S659
5055
319.5
528
S599
4095
319.5
588
S539
3135
319.5
349
G112
6979
319.5
409
S718
5999
202.5
469
S658
5039
202.5
529
S598
4079
202.5
589
S538
3119
202.5
350
G110
6963
202.5
410
S717
5983
319.5
470
S657
5023
319.5
530
S597
4063
319.5
590
S537
3103
319.5
351
G108
6947
319.5
411
S716
5967
202.5
471
S656
5007
202.5
531
S596
4047
202.5
591
S536
3087
202.5
352
G106
6931
202.5
412
S715
5951
319.5
472
S655
4991
319.5
532
S595
4031
319.5
592
S535
3071
319.5
353
G104
6915
319.5
413
S714
5935
202.5
473
S654
4975
202.5
533
S594
4015
202.5
593
S534
3055
202.5
354
G102
6899
202.5
414
S713
5919
319.5
474
S653
4959
319.5
534
S593
3999
319.5
594
S533
3039
319.5
355
G100
6883
319.5
415
S712
5903
202.5
475
S652
4943
202.5
535
S592
3983
202.5
595
S532
3023
202.5
356
G98
6867
202.5
416
S711
5887
319.5
476
S651
4927
319.5
536
S591
3967
319.5
596
S531
3007
319.5
357
G96
6851
319.5
417
S710
5871
202.5
477
S650
4911
202.5
537
S590
3951
202.5
597
S530
2991
202.5
358
G94
6835
202.5
418
S709
5855
319.5
478
S649
4895
319.5
538
S589
3935
319.5
598
S529
2975
319.5
359
G92
6819
319.5
419
S708
5839
202.5
479
S648
4879
202.5
539
S588
3919
202.5
599
S528
2959
202.5
360
G90
6803
202.5
420
S707
5823
319.5
480
S647
4863
319.5
540
S587
3903
319.5
600
S527
2943
319.5
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 16 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
No.
Name
X
Y
No.
Name
X
Y
No.
Name
X
Y
No.
Name
X
Y
No.
Name
X
Y
601
S526
2927
202.5
661
S466
1967
202.5
721
S406
1007
202.5
781
S348
-479
319.5
841
S288
-1439
319.5
602
S525
2911
319.5
662
S465
1951
319.5
722
S405
991
319.5
782
S347
-495
202.5
842
S287
-1455
202.5
603
S524
2895
202.5
663
S464
1935
202.5
723
S404
975
202.5
783
S346
-511
319.5
843
S286
-1471
319.5
604
S523
2879
319.5
664
S463
1919
319.5
724
S403
959
319.5
784
S345
-527
202.5
844
S285
-1487
202.5
605
S522
2863
202.5
665
S462
1903
202.5
725
S402
943
202.5
785
S344
-543
319.5
845
S284
-1503
319.5
606
S521
2847
319.5
666
S461
1887
319.5
726
S401
927
319.5
786
S343
-559
202.5
846
S283
-1519
202.5
607
S520
2831
202.5
667
S460
1871
202.5
727
S400
911
202.5
787
S342
-575
319.5
847
S282
-1535
319.5
608
S519
2815
319.5
668
S459
1855
319.5
728
S399
895
319.5
788
S341
-591
202.5
848
S281
-1551
202.5
609
S518
2799
202.5
669
S458
1839
202.5
729
S398
879
202.5
789
S340
-607
319.5
849
S280
-1567
319.5
610
S517
2783
319.5
670
S457
1823
319.5
730
S397
863
319.5
790
S339
-623
202.5
850
S279
-1583
202.5
611
S516
2767
202.5
671
S456
1807
202.5
731
S396
847
202.5
791
S338
-639
319.5
851
S278
-1599
319.5
612
S515
2751
319.5
672
S455
1791
319.5
732
S395
831
319.5
792
S337
-655
202.5
852
S277
-1615
202.5
613
S514
2735
202.5
673
S454
1775
202.5
733
S394
815
202.5
793
S336
-671
319.5
853
S276
-1631
319.5
614
S513
2719
319.5
674
S453
1759
319.5
734
S393
799
319.5
794
S335
-687
202.5
854
S275
-1647
202.5
615
S512
2703
202.5
675
S452
1743
202.5
735
S392
783
202.5
795
S334
-703
319.5
855
S274
-1663
319.5
616
S511
2687
319.5
676
S451
1727
319.5
736
S391
767
319.5
796
S333
-719
202.5
856
S273
-1679
202.5
617
S510
2671
202.5
677
S450
1711
202.5
737
S390
751
202.5
797
S332
-735
319.5
857
S272
-1695
319.5
618
S509
2655
319.5
678
S449
1695
319.5
738
S389
735
319.5
798
S331
-751
202.5
858
S271
-1711
202.5
619
S508
2639
202.5
679
S448
1679
202.5
739
S388
719
202.5
799
S330
-767
319.5
859
S270
-1727
319.5
620
S507
2623
319.5
680
S447
1663
319.5
740
S387
703
319.5
800
S329
-783
202.5
860
S269
-1743
202.5
621
S506
2607
202.5
681
S446
1647
202.5
741
S386
687
202.5
801
S328
-799
319.5
861
S268
-1759
319.5
622
S505
2591
319.5
682
S445
1631
319.5
742
S385
671
319.5
802
S327
-815
202.5
862
S267
-1775
202.5
623
S504
2575
202.5
683
S444
1615
202.5
743
S384
655
202.5
803
S326
-831
319.5
863
S266
-1791
319.5
624
S503
2559
319.5
684
S443
1599
319.5
744
S383
639
319.5
804
S325
-847
202.5
864
S265
-1807
202.5
625
S502
2543
202.5
685
S442
1583
202.5
745
S382
623
202.5
805
S324
-863
319.5
865
S264
-1823
319.5
626
S501
2527
319.5
686
S441
1567
319.5
746
S381
607
319.5
806
S323
-879
202.5
866
S263
-1839
202.5
627
S500
2511
202.5
687
S440
1551
202.5
747
S380
591
202.5
807
S322
-895
319.5
867
S262
-1855
319.5
628
S499
2495
319.5
688
S439
1535
319.5
748
S379
575
319.5
808
S321
-911
202.5
868
S261
-1871
202.5
629
S498
2479
202.5
689
S438
1519
202.5
749
S378
559
202.5
809
S320
-927
319.5
869
S260
-1887
319.5
630
S497
2463
319.5
690
S437
1503
319.5
750
S377
543
319.5
810
S319
-943
202.5
870
S259
-1903
202.5
631
S496
2447
202.5
691
S436
1487
202.5
751
S376
527
202.5
811
S318
-959
319.5
871
S258
-1919
319.5
632
S495
2431
319.5
692
S435
1471
319.5
752
S375
511
319.5
812
S317
-975
202.5
872
S257
-1935
202.5
633
S494
2415
202.5
693
S434
1455
202.5
753
S374
495
202.5
813
S316
-991
319.5
873
S256
-1951
319.5
634
S493
2399
319.5
694
S433
1439
319.5
754
S373
479
319.5
814
S315
-1007
202.5
874
S255
-1967
202.5
635
S492
2383
202.5
695
S432
1423
202.5
755
S372
463
202.5
815
S314
-1023
319.5
875
S254
-1983
319.5
636
S491
2367
319.5
696
S431
1407
319.5
756
S371
447
319.5
816
S313
-1039
202.5
876
S253
-1999
202.5
637
S490
2351
202.5
697
S430
1391
202.5
757
S370
431
202.5
817
S312
-1055
319.5
877
S252
-2015
319.5
638
S489
2335
319.5
698
S429
1375
319.5
758
S369
415
319.5
818
S311
-1071
202.5
878
S251
-2031
202.5
639
S488
2319
202.5
699
S428
1359
202.5
759
S368
399
202.5
819
S310
-1087
319.5
879
S250
-2047
319.5
640
S487
2303
319.5
700
S427
1343
319.5
760
S367
383
319.5
820
S309
-1103
202.5
880
S249
-2063
202.5
641
S486
2287
202.5
701
S426
1327
202.5
761
S366
367
202.5
821
S308
-1119
319.5
881
S248
-2079
319.5
642
S485
2271
319.5
702
S425
1311
319.5
762
S365
351
319.5
822
S307
-1135
202.5
882
S247
-2095
202.5
643
S484
2255
202.5
703
S424
1295
202.5
763
S364
335
202.5
823
S306
-1151
319.5
883
S246
-2111
319.5
644
S483
2239
319.5
704
S423
1279
319.5
764
S363
319
319.5
824
S305
-1167
202.5
884
S245
-2127
202.5
645
S482
2223
202.5
705
S422
1263
202.5
765
S362
303
202.5
825
S304
-1183
319.5
885
S244
-2143
319.5
646
S481
2207
319.5
706
S421
1247
319.5
766
S361
287
319.5
826
S303
-1199
202.5
886
S243
-2159
202.5
647
S480
2191
202.5
707
S420
1231
202.5
767 DUMMY23
271
202.5
827
S302
-1215
319.5
887
S242
-2175
319.5
648
S479
2175
319.5
708
S419
1215
319.5
768 DUMMY24
-271
202.5
828
S301
-1231
202.5
888
S241
-2191
202.5
649
S478
2159
202.5
709
S418
1199
202.5
769
S360
-287
319.5
829
S300
-1247
319.5
889
S240
-2207
319.5
650
S477
2143
319.5
710
S417
1183
319.5
770
S359
-303
202.5
830
S299
-1263
202.5
890
S239
-2223
202.5
651
S476
2127
202.5
711
S416
1167
202.5
771
S358
-319
319.5
831
S298
-1279
319.5
891
S238
-2239
319.5
652
S475
2111
319.5
712
S415
1151
319.5
772
S357
-335
202.5
832
S297
-1295
202.5
892
S237
-2255
202.5
653
S474
2095
202.5
713
S414
1135
202.5
773
S356
-351
319.5
833
S296
-1311
319.5
893
S236
-2271
319.5
654
S473
2079
319.5
714
S413
1119
319.5
774
S355
-367
202.5
834
S295
-1327
202.5
894
S235
-2287
202.5
655
S472
2063
202.5
715
S412
1103
202.5
775
S354
-383
319.5
835
S294
-1343
319.5
895
S234
-2303
319.5
656
S471
2047
319.5
716
S411
1087
319.5
776
S353
-399
202.5
836
S293
-1359
202.5
896
S233
-2319
202.5
657
S470
2031
202.5
717
S410
1071
202.5
777
S352
-415
319.5
837
S292
-1375
319.5
897
S232
-2335
319.5
658
S469
2015
319.5
718
S409
1055
319.5
778
S351
-431
202.5
838
S291
-1391
202.5
898
S231
-2351
202.5
659
S468
1999
202.5
719
S408
1039
202.5
779
S350
-447
319.5
839
S290
-1407
319.5
899
S230
-2367
319.5
660
S467
1983
319.5
720
S407
1023
319.5
780
S349
-463
202.5
840
S289
-1423
202.5
900
S229
-2383
202.5
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 17 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
No. Name
ILI9325
X
Y
No.
Name
X
Y
No.
Name
X
Y
No.
Name
X
Y
No.
Name
X
Y
901
S228
-2399
319.5
961
S168
-3359
319.5
1021
S108
-4319
319.5
1081
S48
-5279
319.5
1141
G21
-6259
202.5
902
S227
-2415
202.5
962
S167
-3375
202.5
1022
S107
-4335
202.5
1082
S47
-5295
202.5
1142
G23
-6275
319.5
903
S226
-2431
319.5
963
S166
-3391
319.5
1023
S106
-4351
319.5
1083
S46
-5311
319.5
1143
G25
-6291
202.5
904
S225
-2447
202.5
964
S165
-3407
202.5
1024
S105
-4367
202.5
1084
S45
-5327
202.5
1144
G27
-6307
319.5
905
S224
-2463
319.5
965
S164
-3423
319.5
1025
S104
-4383
319.5
1085
S44
-5343
319.5
1145
G29
-6323
202.5
906
S223
-2479
202.5
966
S163
-3439
202.5
1026
S103
-4399
202.5
1086
S43
-5359
202.5
1146
G31
-6339
319.5
907
S222
-2495
319.5
967
S162
-3455
319.5
1027
S102
-4415
319.5
1087
S42
-5375
319.5
1147
G33
-6355
202.5
908
S221
-2511
202.5
968
S161
-3471
202.5
1028
S101
-4431
202.5
1088
S41
-5391
202.5
1148
G35
-6371
319.5
909
S220
-2527
319.5
969
S160
-3487
319.5
1029
S100
-4447
319.5
1089
S40
-5407
319.5
1149
G37
-6387
202.5
910
S219
-2543
202.5
970
S159
-3503
202.5
1030
S99
-4463
202.5
1090
S39
-5423
202.5
1150
G39
-6403
319.5
911
S218
-2559
319.5
971
S158
-3519
319.5
1031
S98
-4479
319.5
1091
S38
-5439
319.5
1151
G41
-6419
202.5
912
S217
-2575
202.5
972
S157
-3535
202.5
1032
S97
-4495
202.5
1092
S37
-5455
202.5
1152
G43
-6435
319.5
913
S216
-2591
319.5
973
S156
-3551
319.5
1033
S96
-4511
319.5
1093
S36
-5471
319.5
1153
G45
-6451
202.5
914
S215
-2607
202.5
974
S155
-3567
202.5
1034
S95
-4527
202.5
1094
S35
-5487
202.5
1154
G47
-6467
319.5
915
S214
-2623
319.5
975
S154
-3583
319.5
1035
S94
-4543
319.5
1095
S34
-5503
319.5
1155
G49
-6483
202.5
916
S213
-2639
202.5
976
S153
-3599
202.5
1036
S93
-4559
202.5
1096
S33
-5519
202.5
1156
G51
-6499
319.5
917
S212
-2655
319.5
977
S152
-3615
319.5
1037
S92
-4575
319.5
1097
S32
-5535
319.5
1157
G53
-6515
202.5
918
S211
-2671
202.5
978
S151
-3631
202.5
1038
S91
-4591
202.5
1098
S31
-5551
202.5
1158
G55
-6531
319.5
919
S210
-2687
319.5
979
S150
-3647
319.5
1039
S90
-4607
319.5
1099
S30
-5567
319.5
1159
G57
-6547
202.5
920
S209
-2703
202.5
980
S149
-3663
202.5
1040
S89
-4623
202.5
1100
S29
-5583
202.5
1160
G59
-6563
319.5
921
S208
-2719
319.5
981
S148
-3679
319.5
1041
S88
-4639
319.5
1101
S28
-5599
319.5
1161
G61
-6579
202.5
922
S207
-2735
202.5
982
S147
-3695
202.5
1042
S87
-4655
202.5
1102
S27
-5615
202.5
1162
G63
-6595
319.5
923
S206
-2751
319.5
983
S146
-3711
319.5
1043
S86
-4671
319.5
1103
S26
-5631
319.5
1163
G65
-6611
202.5
924
S205
-2767
202.5
984
S145
-3727
202.5
1044
S85
-4687
202.5
1104
S25
-5647
202.5
1164
G67
-6627
319.5
925
S204
-2783
319.5
985
S144
-3743
319.5
1045
S84
-4703
319.5
1105
S24
-5663
319.5
1165
G69
-6643
202.5
926
S203
-2799
202.5
986
S143
-3759
202.5
1046
S83
-4719
202.5
1106
S23
-5679
202.5
1166
G71
-6659
319.5
927
S202
-2815
319.5
987
S142
-3775
319.5
1047
S82
-4735
319.5
1107
S22
-5695
319.5
1167
G73
-6675
202.5
928
S201
-2831
202.5
988
S141
-3791
202.5
1048
S81
-4751
202.5
1108
S21
-5711
202.5
1168
G75
-6691
319.5
929
S200
-2847
319.5
989
S140
-3807
319.5
1049
S80
-4767
319.5
1109
S20
-5727
319.5
1169
G77
-6707
202.5
930
S199
-2863
202.5
990
S139
-3823
202.5
1050
S79
-4783
202.5
1110
S19
-5743
202.5
1170
G79
-6723
319.5
931
S198
-2879
319.5
991
S138
-3839
319.5
1051
S78
-4799
319.5
1111
S18
-5759
319.5
1171
G81
-6739
202.5
932
S197
-2895
202.5
992
S137
-3855
202.5
1052
S77
-4815
202.5
1112
S17
-5775
202.5
1172
G83
-6755
319.5
933
S196
-2911
319.5
993
S136
-3871
319.5
1053
S76
-4831
319.5
1113
S16
-5791
319.5
1173
G85
-6771
202.5
934
S195
-2927
202.5
994
S135
-3887
202.5
1054
S75
-4847
202.5
1114
S15
-5807
202.5
1174
G87
-6787
319.5
935
S194
-2943
319.5
995
S134
-3903
319.5
1055
S74
-4863
319.5
1115
S14
-5823
319.5
1175
G89
-6803
202.5
936
S193
-2959
202.5
996
S133
-3919
202.5
1056
S73
-4879
202.5
1116
S13
-5839
202.5
1176
G91
-6819
319.5
937
S192
-2975
319.5
997
S132
-3935
319.5
1057
S72
-4895
319.5
1117
S12
-5855
319.5
1177
G93
-6835
202.5
938
S191
-2991
202.5
998
S131
-3951
202.5
1058
S71
-4911
202.5
1118
S11
-5871
202.5
1178
G95
-6851
319.5
939
S190
-3007
319.5
999
S130
-3967
319.5
1059
S70
-4927
319.5
1119
S10
-5887
319.5
1179
G97
-6867
202.5
940
S189
-3023
202.5
1000
S129
-3983
202.5
1060
S69
-4943
202.5
1120
S9
-5903
202.5
1180
G99
-6883
319.5
941
S188
-3039
319.5
1001
S128
-3999
319.5
1061
S68
-4959
319.5
1121
S8
-5919
319.5
1181
G101
-6899
202.5
942
S187
-3055
202.5
1002
S127
-4015
202.5
1062
S67
-4975
202.5
1122
S7
-5935
202.5
1182
G103
-6915
319.5
943
S186
-3071
319.5
1003
S126
-4031
319.5
1063
S66
-4991
319.5
1123
S6
-5951
319.5
1183
G105
-6931
202.5
944
S185
-3087
202.5
1004
S125
-4047
202.5
1064
S65
-5007
202.5
1124
S5
-5967
202.5
1184
G107
-6947
319.5
945
S184
-3103
319.5
1005
S124
-4063
319.5
1065
S64
-5023
319.5
1125
S4
-5983
319.5
1185
G109
-6963
202.5
946
S183
-3119
202.5
1006
S123
-4079
202.5
1066
S63
-5039
202.5
1126
S3
-5999
202.5
1186
G111
-6979
319.5
947
S182
-3135
319.5
1007
S122
-4095
319.5
1067
S62
-5055
319.5
1127
S2
-6015
319.5
1187
G113
-6995
202.5
948
S181
-3151
202.5
1008
S121
-4111
202.5
1068
S61
-5071
202.5
1128
S1
-6031
202.5
1188
G115
-7011
319.5
949
S180
-3167
319.5
1009
S120
-4127
319.5
1069
S60
-5087
319.5
1129 DUMMY25
-6047
319.5
1189
G117
-7027
202.5
950
S179
-3183
202.5
1010
S119
-4143
202.5
1070
S59
-5103
202.5
1130 DUMMY26
-6083
319.5
1190
G119
-7043
319.5
951
S178
-3199
319.5
1011
S118
-4159
319.5
1071
S58
-5119
319.5
1131
G1
-6099
202.5
1191
G121
-7059
202.5
952
S177
-3215
202.5
1012
S117
-4175
202.5
1072
S57
-5135
202.5
1132
G3
-6115
319.5
1192
G123
-7075
319.5
953
S176
-3231
319.5
1013
S116
-4191
319.5
1073
S56
-5151
319.5
1133
G5
-6131
202.5
1193
G125
-7091
202.5
954
S175
-3247
202.5
1014
S115
-4207
202.5
1074
S55
-5167
202.5
1134
G7
-6147
319.5
1194
G127
-7107
319.5
955
S174
-3263
319.5
1015
S114
-4223
319.5
1075
S54
-5183
319.5
1135
G9
-6163
202.5
1195
G129
-7123
202.5
956
S173
-3279
202.5
1016
S113
-4239
202.5
1076
S53
-5199
202.5
1136
G11
-6179
319.5
1196
G131
-7139
319.5
957
S172
-3295
319.5
1017
S112
-4255
319.5
1077
S52
-5215
319.5
1137
G13
-6195
202.5
1197
G133
-7155
202.5
958
S171
-3311
202.5
1018
S111
-4271
202.5
1078
S51
-5231
202.5
1138
G15
-6211
319.5
1198
G135
-7171
319.5
959
S170
-3327
319.5
1019
S110
-4287
319.5
1079
S50
-5247
319.5
1139
G17
-6227
202.5
1199
G137
-7187
202.5
960
S169
-3343
202.5
1020
S109
-4303
202.5
1080
S49
-5263
202.5
1140
G19
-6243
319.5
1200
G139
-7203
319.5
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 18 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
No.
Name
X
Y
No.
Name
X
Y
1201
G141
-7219
202.5
1261
G261
-8179
202.5
1202
G143
-7235
319.5
1262
G263
-8195
319.5
1203
G145
-7251
202.5
1263
G265
-8211
202.5
1204
G147
-7267
319.5
1264
G267
-8227
319.5
1205
G149
-7283
202.5
1265
G269
-8243
202.5
1206
G151
-7299
319.5
1266
G271
-8259
319.5
1207
G153
-7315
202.5
1267
G273
-8275
202.5
1208
G155
-7331
319.5
1268
G275
-8291
319.5
1209
G157
-7347
202.5
1269
G277
-8307
202.5
1210
G159
-7363
319.5
1270
G279
-8323
319.5
1211
G161
-7379
202.5
1271
G281
-8339
202.5
1212
G163
-7395
319.5
1272
G283
-8355
319.5
1213
G165
-7411
202.5
1273
G285
-8371
202.5
1214
G167
-7427
319.5
1274
G287
-8387
319.5
1215
G169
-7443
202.5
1275
G289
-8403
202.5
1216
G171
-7459
319.5
1276
G291
-8419
319.5
1217
G173
-7475
202.5
1277
G293
-8435
202.5
1218
G175
-7491
319.5
1278
G295
-8451
319.5
1219
G177
-7507
202.5
1279
G297
-8467
202.5
1220
G179
-7523
319.5
1280
G299
-8483
319.5
1221
G181
-7539
202.5
1281
G301
-8499
202.5
1222
G183
-7555
319.5
1282
G303
-8515
319.5
1223
G185
-7571
202.5
1283
G305
-8531
202.5
1224
G187
-7587
319.5
1284
G307
-8547
319.5
1225
G189
-7603
202.5
1285
G309
-8563
202.5
1226
G191
-7619
319.5
1286
G311
-8579
319.5
1227
G193
-7635
202.5
1287
G313
-8595
202.5
1228
G195
-7651
319.5
1288
G315
-8611
319.5
1229
G197
-7667
202.5
1289
G317
-8627
202.5
1230
G199
-7683
319.5
1290
G319
-8643
319.5
1231
G201
-7699
202.5
1291
DUMMY27
-8659
202.5
1232
G203
-7715
319.5
X
Y
1233
G205
-7731
202.5
1-a
-8751
269
1234
G207
-7747
319.5
1-b
8751
269
1235
G209
-7763
202.5
1236
G211
-7779
319.5
1237
G213
-7795
202.5
1238
G215
-7811
319.5
1239
G217
-7827
202.5
1240
G219
-7843
319.5
1241
G221
-7859
202.5
1242
G223
-7875
319.5
1243
G225
-7891
202.5
1244
G227
-7907
319.5
1245
G229
-7923
202.5
1246
G231
-7939
319.5
1247
G233
-7955
202.5
1248
G235
-7971
319.5
1249
G237
-7987
202.5
1250
G239
-8003
319.5
1251
G241
-8019
202.5
1252
G243
-8035
319.5
1253
G245
-8051
202.5
1254
G247
-8067
319.5
1255
G249
-8083
202.5
1256
G251
-8099
319.5
1257
G253
-8115
202.5
1258
G255
-8131
319.5
1259
G257
-8147
202.5
1260
G259
-8163
319.5
Alignment mark
ILI9325
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 19 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
16
16
ILI9325
16
98
S1 ~ S720
G1 ~ G320
19
DUMMY20~27
(No. 244 ~ 1291)
98
Unit: um
80
I/O Pads
50
Pad Pump
x
Pad Pump
50
(No. 1 ~ 243)
y
X=20, 30, 35
Y=70, 80, 85
Unit: um
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 20 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
6. Block Description
MPU System Interface
ILI9325 supports three system high-speed interfaces: i80-system high-speed interfaces to 8-, 9-, 16-, 18-bit
parallel ports and serial peripheral interface (SPI). The interface mode is selected by setting the IM[3:0] pins.
ILI9325 has a 16-bit index register (IR), an 18-bit write-data register (WDR), and an 18-bit read-data register
(RDR). The IR is the register to store index information from control registers and the internal GRAM. The
WDR is the register to temporarily store data to be written to control registers and the internal GRAM. The
RDR is the register to temporarily store data read from the GRAM. Data from the MPU to be written to the
internal GRAM are first written to the WDR and then automatically written to the internal GRAM in internal
operation. Data are read via the RDR from the internal GRAM. Therefore, invalid data are read out to the data
bus when the ILI9325 read the first data from the internal GRAM. Valid data are read out after the ILI9325
performs the second read operation.
Registers are written consecutively as the register execution time except starting oscillator takes 0 clock
cycle.
Registers selection by system interface (8-/9-/16-/18-bit bus width)
Function
Write an index to IR register
Read an internal status
Write to control registers or the internal GRAM by WDR register.
Read from the internal GRAM by RDR register.
Registers selection by the SPI system interface
Function
Write an index to IR register
Read an internal status
Write to control registers or the internal GRAM by WDR register.
Read from the internal GRAM by RDR register.
RS
0
0
1
1
I80
nWR nRD
0
1
1
0
0
1
1
0
R/W
0
1
0
1
RS
0
0
1
1
Parallel RGB Interface
ILI9325 supports the RGB interface and the VSYNC interface as the external interface for displaying a moving
picture. When the RGB interface is selected, display operations are synchronized with externally supplied
signals, VSYNC, HSYNC, and DOTCLK. In RGB interface mode, data (DB17-0) are written in synchronization
with these signals according to the polarity of enable signal (ENABLE) to prevent flicker on display while
updating display data.
In VSYNC interface mode, the display operation is synchronized with the internal clock except frame
synchronization, where the operation is synchronized with the VSYNC signal. Display data are written to the
internal GRAM via the system interface. In this case, there are constraints in speed and method in writing data
to the internal RAM. For details, see the “External Display Interface” section. The ILI9325 allows for switching
between the external display interface and the system interface by instruction so that the optimum interface is
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 21 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
selected for the kind of picture to be displayed on the screen (still and/or moving picture(s)). The RGB
interface, by writing all display data to the internal RAM, allows for transferring data only when updating the
frames of a moving picture, contributing to low power requirement for moving picture display.
Bit Operation
The ILI9325 supports a write data mask function for selectively writing data to the internal RAM in units of bits
and a logical/compare operation to write data to the GRAM only when a condition is met as a result of
comparing the data and the compare register bits. For details, see “Graphics Operation Functions”.
Address Counter (AC)
The address counter (AC) gives an address to the internal GRAM. When the index of the register for setting a
RAM address in the AC is written to the IR, the address information is sent from the IR to the AC. As writing
data to the internal GRAM, the address in the AC is automatically updated plus or minus 1. The window
address function enables writing data only in the rectangular area arbitrarily set by users on the GRAM.
Graphics RAM (GRAM)
GRAM is graphics RAM storing bit-pattern data of 172,820 (240 x 320x 18/8) bytes with 18 bits per pixel.
Grayscale Voltage Generating Circuit
The grayscale voltage generating circuit generates a liquid crystal drive voltage according to grayscale data
set in the γ-correction register to display in 262,144 colors. For details, see the “γ-Correction Register”
section.
Timing Controller
The timing generator generates a timing signal for operation of internal circuits such as the internal GRAM.
The timing for the display operation such as RAM read operation and the timing for the internal operation such
as access from the MPU are generated in the way not to interfere each other.
Oscillator (OSC)
ILI9325 generates RC oscillation with an internal oscillation resistor. The frame rate is adjusted by the register
setting.
LCD Driver Circuit
The LCD driver circuit of ILI9325 consists of a 720-output source driver (S1 ~ S720) and a 320-output gate
driver (G1~G320). Display pattern data are latched when the 720th bit data are input. The latched data control
the source driver and generate a drive waveform. The gate driver for scanning gate lines outputs either VGH
or VGL level. The shift direction of 720 source outputs from the source driver is set with the SS bit and the
shift direction of gate outputs from the gate driver is set with the GS bit. The scan mode by the gate driver is
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 22 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
set with the SM bit. These bits allow setting an appropriate scan method for an LCD module.
LCD Driver Power Supply Circuit
The LCD drive power supply circuit generates the voltage levels VREG1OUT, VGH, VGL and Vcom for
driving an LCD.
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 23 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
7. System Interface
7.1. Interface Specifications
ILI9325 has the system interface to read/write the control registers and display graphics memory (GRAM),
and the RGB Input Interface for displaying a moving picture. User can select an optimum interface to display
the moving or still picture with efficient data transfer. All display data are stored in the GRAM to reduce the
data transfer efforts and only the updating data is necessary to be transferred. User can only update a
sub-range of GRAM by using the window address function.
ILI9325 also has the RGB interface and VSYNC interface to transfer the display data without flicker the
moving picture on the screen. In RGB interface mode, the display data is written into the GRAM through the
control signals of ENABLE, VSYNC, HSYNC, DOTCLK and data bus DB[17:0].
In VSYNC interface mode, the internal display timing is synchronized with the frame synchronization signal
(VSYNC). The VSYNC interface mode enables to display the moving picture display through the system
interface. In this case, there are some constraints of speed and method to write data to the internal RAM.
ILI9325 operates in one of the following 4 modes. The display mode can be switched by the control register.
When switching from one mode to another, refer to the sequences mentioned in the sections of RGB and
VSYNC interfaces.
Operation Mode
RAM Access Setting
(RM)
Display Operation Mode
(DM[1:0])
Internal operating clock only
(Displaying still pictures)
System interface
(RM = 0)
Internal operating clock
(DM[1:0] = 00)
RGB interface (1)
(Displaying moving pictures)
RGB interface
(RM = 1)
RGB interface
(DM[1:0] = 01)
RGB interface (2)
(Rewriting still pictures while
displaying moving pictures)
System interface
(RM = 0)
RGB interface
(DM[1:0] = 01)
VSYNC interface
(Displaying moving pictures)
System interface
(RM = 0)
VSYNC interface
(DM[1:0] = 01)
Note 1) Registers are set only via the system interface.
Note 2) The RGB-I/F and the VSYNC-I/F are not available simultaneously.
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 24 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
System
Interface
18/16/6
ILI9325
nCS
RS
nWR
nRD
DB[17:0]
System
ILI9325
ENABLE
VSYNC
HSYNC
DOTCLK
RGB
Interface
Figure1 System Interface and RGB Interface connection
7.2. Input Interfaces
The following are the system interfaces available with the ILI9325. The interface is selected by setting the
IM[3:0] pins. The system interface is used for setting registers and GRAM access.
IM3
IM2
IM1
IM0/ID
0
0
0
0
0
0
1
1
1
1
1
0
0
0
0
1
1
0
0
0
0
1
0
0
1
1
0
1
0
0
1
1
*
0
1
0
1
ID
*
0
1
0
1
*
Interface Mode
Setting invalid
Setting invalid
i80-system 16-bit interface
i80-system 8-bit interface
Serial Peripheral Interface (SPI)
Setting invalid
Setting invalid
Setting invalid
i80-system18-bit interface
i80-system 9-bit interface
Setting invalid
DB Pin
DB[17:10], DB[8:1]
DB[17:10]
SDI, SDO (DB[1:0])
DB[17:0]
DB[17:9]
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 25 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
7.2.1. i80/18-bit System Interface
The i80/18-bit system interface is selected by setting the IM[3:0] as “1010” levels.
System
nCS
A2
nWR
nRD
D[31:0]
nCS
RS
nWR
nRD
DB[17:0]
18
18-bit System Interface (262K colors) TRI=0, DFM[1:0]=00
Input Data
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
DB
11
DB
10
DB
9
DB
8
DB
7
DB
6
DB
5
DB
4
DB
3
DB
2
DB
1
DB
0
Write Data
Register
WD
17
WD
16
WD
15
WD
14
WD
13
WD
12
WD
11
WD
10
WD
9
WD
8
WD
7
WD
6
WD
5
WD
4
WD
3
WD
2
WD
1
WD
0
GRAM Data &
RGB Mapping
R5
R4
R3
R2
R1
R0
G5
G4
G3
G2
G1
G0
B5
B4
B3
B2
B1
B0
Figure2 18-bit System Interface Data Format
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 26 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
7.2.2. i80/16-bit System Interface
The i80/16-bit system interface is selected by setting the IM[3:0] as “0010” levels. The 262K or 65K color can
be display through the 16-bit MPU interface. When the 262K color is displayed, two transfers (1st transfer: 2
bits, 2nd transfer: 16 bits or 1st transfer: 16 bits, 2nd transfer: 2 bits) are necessary for the 16-bit CPU interface.
TRI
DFM
16-bit MPU System Interface Data Format
system 16-bit interface (1 transfers/pixel) 65,536 colors
0
*
1st Transfer
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
DB
11
DB
10
R5
R4
R3
R2
R1
R0
G5
G4
G3
DB
8
DB
7
DB
6
DB
5
DB
4
DB
3
DB
2
DB
1
G2
G1
G0
B5
B4
B3
B2
B1
B0
80-system 16-bit interface (2 transfers/pixel) 262,144 colors
1
0
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
DB
11
R5
R4
R3
R2
R1
R0
G5
1st Transfer
2nd Transfer
DB
DB
17
16
DB
10
DB
8
DB
7
DB
6
DB
5
DB
4
DB
3
DB
2
DB
1
G4
G3
G2
G1
G0
B5
B4
B3
B2
B1
B0
80-system 16-bit interface (2 transfers/pixel) 262,144 colors
1
1
1st Transfer
DB
DB
2
1
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
DB
11
R5
R3
R2
R1
R0
G5
G4
G3
R4
2nd Transfer
DB
10
DB
8
DB
7
DB
6
DB
5
DB
4
DB
3
DB
2
DB
1
G2
G1
G0
B5
B4
B3
B2
B1
B0
Figure3 16-bit System Interface Data Format
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 27 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
7.2.3. i80/9-bit System Interface
The i80/9-bit system interface is selected by setting the IM[3:0] as “1011” and the DB17~DB9 pins are used to
transfer the data. When writing the 16-bit register, the data is divided into upper byte (8 bits and LSB is not
used) lower byte and the upper byte is transferred first. The display data is also divided in upper byte (9 bits)
and lower byte, and the upper byte is transferred first. The unused DB[8:0] pins must be tied to either Vcc or
GND.
nCS
A1
nWR
nRD
D[8:0]
System
nCS
RS
nWR
nRD
DB[17:9]
9
9-bit System Interface (262K colors) TRI=0, DFM[1:0]=00
1st Transfer (Upper bits)
2nd Transfer (Lower bits)
Input Data
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
DB
11
DB
10
DB
9
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
DB
11
DB
10
DB
9
Write Data
Register
WD
17
WD
16
WD
15
WD
14
WD
13
WD
12
WD
11
WD
10
WD
9
WD
8
WD
7
WD
6
WD
5
WD
4
WD
3
WD
2
WD
1
WD
0
GRAM Data &
RGB Mapping
R5
R4
R3
R2
R1
R0
G5
G4
G3
G2
G1
G0
B5
B4
B3
B2
B1
B0
Figure4 9-bit System Interface Data Format
7.2.4. i80/8-bit System Interface
The i80/8-bit system interface is selected by setting the IM[3:0] as “0011” and the DB17~DB10 pins are used
to transfer the data. When writing the 16-bit register, the data is divided into upper byte (8 bits and LSB is not
used) lower byte and the upper byte is transferred first. The display data is also divided in upper byte (8 bits)
and lower byte, and the upper byte is transferred first. The written data is expanded into 18 bits internally (see
the figure below) and then written into GRAM. The unused DB[9:0] pins must be tied to either Vcc or GND.
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 28 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
TRI
DFM
ILI9325
8-bit MPU System Interface Data Format
system 8-bit interface (2 transfers/pixel) 65,536 colors
0
*
DB
17
DB
16
DB
15
R5
R4
R3
1st Transfer
DB
14
DB
13
DB
12
DB
11
DB
10
R2
R1
R0
G5
G4
G3
DB
17
DB
16
DB
15
G2
G1
2nd Transfer
DB
14
DB
13
DB
12
DB
11
DB
10
G0
B5
B4
B3
B2
B1
B0
80-system 8-bit interface (3 transfers/pixel) 262,144 colors
1
0
1st Transfer
DB
DB
11
10
DB
17
DB
16
DB
15
R5
R3
R2
R1
R4
2nd Transfer
DB
14
DB
13
DB
12
DB
11
DB
10
DB
17
DB
16
DB
15
R0
G5
G4
G3
G2
G1
G0
3rd Transfer
DB
14
DB
13
DB
12
DB
11
DB
10
B5
B4
B3
B2
B1
B0
80-system 8-bit interface (3 transfers/pixel) 262,144 colors
1
1
DB
17
DB
16
R5
R4
1st Transfer
DB
15
DB
14
DB
13
DB
12
DB
17
DB
16
R3
R2
R1
R0
G5
G4
2nd Transfer
DB
15
DB
14
DB
13
DB
12
DB
17
DB
16
G3
G2
G1
G0
B5
B4
3rd Transfer
DB
15
DB
14
DB
13
DB
12
B3
B2
B1
B0
Figure5 8-bit System Interface Data Format
Data transfer synchronization in 8/9-bit bus interface mode
ILI9325 supports a data transfer synchronization function to reset upper and lower counters which count the
transfers numbers of upper and lower byte in 8/9-bit interface mode. If a mismatch arises in the numbers of
transfers between the upper and lower byte counters due to noise and so on, the “00”h register is written 4
times consecutively to reset the upper and lower counters so that data transfer will restart with a transfer of
upper byte. This synchronization function can effectively prevent display error if the upper/lower counters are
periodically reset.
RS
RD
nWR
DB[17:9]
Upper/
Lower
“00”h
“00”h
“00”h
“00”h
Upper
Lower
8-/9-bit transfer
synchronization
Figure6 Data Transfer Synchronization in 8/9-bit System Interface
7.3. Serial Peripheral Interface (SPI)
The Serial Peripheral Interface (SPI) is selected by setting the IM[3:0] pins as “010x” level. The chip select pin
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 29 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
(nCS), the serial transfer clock pin (SCL), the serial data input pin (SDI) and the serial data output pin (SDO)
are used in SPI mode. The ID pin sets the least significant bit of the identification code. The DB[17:0] pins,
which are not used, must be tied to either IOVcc or DGND.
The SPI interface operation enables from the falling edge of nCS and ends of data transfer on the rising edge
of nCS. The start byte is transferred to start the SPI interface and the read/write operation and RS information
are also included in the start byte. When the start byte is matched, the subsequent data is received by
ILI9325.
The seventh bit of start byte is RS bit. When RS = “0”, either index write operation or status read operation is
executed. When RS = “1”, either register write operation or RAM read/write operation is executed. The eighth
bit of the start byte is used to select either read or write operation (R/W bit). Data is written when the R/W bit is
“0” and read back when the R/W bit is “1”.
After receiving the start byte, ILI9325 starts to transfer or receive the data in unit of byte and the data transfer
starts from the MSB bit. All the registers of the ILI9325 are 16-bit format and receive the first and the second
byte datat as the upper and the lower eight bits of the 16-bit register respectively. In SPI mode, 5 bytes
dummy read is necessary and the valid data starts from 6th byte of read back data.
Start Byte Format
Transferred bits
Start byte format
S
Transfer start
1
2
0
1
3
4
Device ID code
1
1
5
6
0
ID
7
RS
1/0
8
R/W
1/0
Note: ID bit is selected by setting the IM0/ID pin.
RS and R/W Bit Function
RS
0
0
1
1
R/W
0
1
0
1
Function
Set an index register
Read a status
Write a register or GRAM data
Read a register or GRAM data
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 30 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
Serial Peripheral Interface for register access
SPI Input Data
D
15
D
14
D
13
D
12
D
11
D
10
D
9
D
8
D
7
D
6
D
5
D
4
D
3
D
2
D
1
D
0
Register Data
IB
15
IB
14
IB
13
IB
12
IB
11
IB
10
IB
9
IB
8
IB
7
IB
6
IB
5
IB
4
IB
3
IB
2
IB
1
IB
0
D
7
D
6
D
5
D
4
D
3
D
2
D
1
D
0
Serial Peripheral Interface 65K colors
Input Data
D
15
D
14
D
13
D
12
D
11
D
10
D
9
D
8
Write Data Register
WD
17
WD
16
WD
15
WD
14
WD
13
WD
12
WD
11
WD
10
WD
9
WD
8
WD
7
WD
6
WD
5
WD
4
WD
3
WD
2
WD
1
WD
0
GRAM Data
RGB mapping
R5
R4
R3
R2
R1
R0
G5
G4
G3
G2
G1
G0
B5
B4
B3
B2
B1
B0
Figure 7 Data Format of SPI Interface
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 31 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
(a) Basic data transmission through SPI
End
Start
nCS
(Input)
1
2
3
4
5
6
0
1
1
1
0
ID
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
RS RW D15 D14 D13 D12 D11 D10 D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
D2
D1
D0
SCL
(Input)
SDI
(Input)
Start Byte
Index register, registers setting, and GRAM write
SDO
(Output)
D15 D14 D13 D12 D11 D10 D9
D8
D7
D6
D5
D4
D3
Status, registers read and GRAM read
(b) Consecutive data transmission through SPI
Start
nCS
(Input)
1
8
9
16
24
17
25
32
SCL
(Input)
SDI
(Input)
Register 1
upper eight bits
Start Byte
Register 1
lower eight bits
Note: The first byte after the start byte is always the upper eight bits .
Register 2
upper eight bits
Register 2
lower eight bits
Register 1
execution time
(c) GRAM data read transmission
End
Start
nCS
(Input)
SCL
(Input)
SDI
(Input)
Start Byte
RS=1, RW=1
SDO
(Output)
Dummy
read 1
Dummy
read 2
Dummy
read 3
Dummy
read 4
Dummy
read 5
RAM read
upper byte
RAM read
lower byte
Note: Five bytes of invalid dummy data read after the start byte .
(d) Status/registers read transmission
End
Start
nCS
(Input)
1
8
9
16
24
17
SCL
(Input)
SDI
(Input)
SDO
(Output)
Start Byte
Register 1
upper eight bits
Register 1
lower eight bits
Note: One byte of invalid dummy data read after the start byte .
Figure8 Data transmission through serial peripheral interface (SPI)
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 32 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
(e) Basic data transmission through SPI
Start
End
nCS
(Input)
1
2
3
4
5
6
0
1
1
1
0
ID
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
RS RW D23 D22 D21 D120 D19 D18 D17 D16 D15 D14 D13 D12 D11 D10 D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
D8
D7
D6
D5
D4
D3
D2
D1
D0
SCL
(Input)
SDI
(Input)
Start Byte
GRAM data write
SDO
(Output)
D23 D22 D21 D120 D19 D18 D17 D16 D15 D14 D13 D12 D11 D10 D9
GRAM data read
(f) GRAM data write transmission
End
Start
nCS
(Input)
SCL
(Input)
SDI
(Input)
RAM data 1
1st transfer
Start Byte
RAM data 1
2nd transfer
RAM data 1
3rd transfer
SDO
(Output)
RAM data 2
1st transfer
RAM data 2
2nd transfer
GRAM Data (1)
execution time
Note: Five bytes of invalid dummy data read after the start byte.
RAM data 2
3rd transfer
GRAM Data (2)
execution time
(g) GRAM data read transmission
End
Start
nCS
(Input)
SCL
(Input)
SDI
(Input)
SDO
(Output)
Start Byte
RS=1, RW=1
Dummy
read 1
Dummy
read 2
Dummy
read 3
Dummy
read 4
Dummy
read 5
RAM read
1st byte
RAM read
2nd byte
RAM read
3rd byte
Note: Five bytes of invalid dummy data read after the start byte.
RAM data transfer in SPI mode when TRI=1 and DFM[1:0]=10.
Figure9 Data transmission through serial peripheral interface (SPI), TRI=”1” and DFM=”10”)
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 33 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
7.4. VSYNC Interface
ILI9325 supports the VSYNC interface in synchronization with the frame-synchronizing signal VSYNC to
display the moving picture with the i80 system interface. When the VSYNC interface is selected to display a
moving picture, the minimum GRAM update speed is limited and the VSYNC interface is enabled by setting
DM[1:0] = “10” and RM = “0”.
VSYNC
MPU
nCS
RS
nWR
DB[17:0]
Figure10 Data transmission through VSYNC interface)
In the VSYNC mode, the display operation is synchronized with the internal clock and VSYNC input and the
frame rate is determined by the pulse rate of VSYNC signal. All display data are stored in GRAM to minimize
total data transfer required for moving picture display.
VSYNC
Write data to RAM
through system
interface
Rewriting
screen data
Rewriting
screen data
Display operation
synchronized with
internal clocks
Figure11 Moving picture data transmission through VSYNC interface
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 34 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
RAM
Write
VSYNC
Back porch (14 lines)
Display
operation
Display
(320 lines)
Front porch (2 lines)
Black period
Figure12 Operation through VSYNC Interface
The VSYNC interface has the minimum speed limitation of writing data to the internal GRAM via the system
interface, which are calculated from the following formula.
Internal clock frequency (fosc.) [Hz] = FrameFrequency x (DisplayLine (NL) + FrontPorch (FP) + BackPorch
(BP)) x ClockCyclePerLines (RTN) x FrequencyFluctuation.
Minimum RAM write speed (HZ)
320 x DisplayLines (NL)
[(BackPorch(BP)+DisplayLines(NL) - margins] x 16 (clocks) x 1/fosc
Note: When the RAM write operation does not start from the falling edge of VSYNC, the time from the falling
edge of VSYNC until the start of RAM write operation must also be taken into account.
An example of minimum GRAM writing speed and internal clock frequency in VSYNC interface mode is as
below.
[Example]
Display size: 240 RGB × 320 lines
Lines: 320 lines (NL = 1000111)
Back porch: 14 lines (BP = 1110)
Front porch: 2 lines (FP = 0010)
Frame frequency: 60 Hz
Frequency fluctuation: 10%
Internal oscillator clock (fosc.) [Hz] = 60 x [320+ 2 + 14] x 16 clocks x (1.1/0.9) ≒ 394KHz
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 35 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
When calculate the internal clock frequency, the oscillator variation is needed to be taken into consideration.
In the above example, the calculated internal clock frequency with ±10% margin variation is considered and
ensures to complete the display operation within one VSYNC cycle. The causes of frequency variation come
from fabrication process of LSI, room temperature, external resistors and VCI voltage variation.
Minimum speed for RAM writing [Hz] > 240 x 320 x 394K / [ (14 + 320 – 2)lines x 16clocks] ≒ 5.7 MHz
The above theoretical value is calculated based on the premise that the ILI9325 starts to write data into the
internal GRAM on the falling edge of VSYNC. There must at least be a margin of 2 lines between the physical
display line and the GRAM line address where data writing operation is performed. The GRAM write speed of
5.7MHz or more will guarantee the completion of GRAM write operation before the ILI9325 starts to display
the GRAM data on the screen and enable to rewrite the entire screen without flicker.
Notes in using the VSYNC interface
1. The minimum GRAM write speed must be satisfied and the frequency variation must be taken into
consideration.
2. The display frame rate is determined by the VSYNC signal and the period of VSYNC must be longer than
the scan period of an entire display.
3. When switching from the internal clock operation mode (DM[1:0] = “00”) to the VSYNC interface mode or
inversely, the switching starts from the next VSYNC cycle, i.e. after completing the display of the frame.
4. The partial display, vertical scroll, and interlaced scan functions are not available in VSYNC interface mode
and set the AM bit to “0” to transfer display data.
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 36 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
System Interface Mode to VSYNC interface mode
VSYNC interface mode to System Interface Mode
Opeartion through
VSYNC interface
System Interface
Set DM[1:0]=00, RM=0
for system interface mode
Set HWM=1, AM=0
Set GRAM Address
Display operation in
synchronization with
internal clocks
Wait more than 1 frame
Set DM[1:0]=10, RM=0
for VSYNC interface mode
Set index register to R22h
DM[1:0], RM become
enable after completion
of displaying 1 frame
System Interface
Display operation in
synchronization with
VSYNC
DM[1:0], RM become
enable after completion
of displaying 1 frame
Display operation in
synchronization with
internal clocks
Note: input VSYNC for more than 1 frame
period after setting the DM, RM register.
Wait more than 1 frame
Write data to GRAM
through VSYNC interface
ILI9325
Display operation in
synchronization with
VSYNC
Opeartion through
VSYNC interface
Figure13 Transition flow between VSYNC and internal clock operation modes
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 37 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
7.5. RGB Input Interface
The RGB Interface mode is available for ILI9325 and the interface is selected by setting the RIM[1:0] bits as
following table.
RIM1
0
0
1
1
RIM0
0
1
0
1
RGB Interface
18-bit RGB Interface
16-bit RGB Interface
6-bit RGB Interface
Setting prohibited
DB pins
DB[17:0]
DB[17:13], DB[11:1]
DB[17:12]
18-bit RGB Interface (262K colors)
Input Data
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
DB
11
DB
10
DB
9
DB
8
DB
7
DB
6
DB
5
DB
4
DB
3
DB
2
DB
1
DB
0
Write Data
Register
WD
17
WD
16
WD
15
WD
14
WD
13
WD
12
WD
11
WD
10
WD
9
WD
8
WD
7
WD
6
WD
5
WD
4
WD
3
WD
2
WD
1
WD
0
GRAM Data &
RGB Mapping
R5
R4
R3
R2
R1
R0
G5
G4
G3
G2
G1
G0
B5
B4
B3
B2
B1
B0
16-bit RGB Interface (65K colors)
Input Data
DB
17
DB
16
DB
15
DB
14
DB
13
DB
11
DB
10
DB
9
DB
8
DB
7
DB
6
DB
5
DB
4
DB
3
DB
2
DB
1
Write Data
Register
WD
17
WD
16
WD
15
WD
14
WD
13
WD
11
WD
10
WD
9
WD
8
WD
7
WD
6
WD
5
WD
4
WD
3
WD
2
WD
1
GRAM Data &
RGB Mapping
R5
R4
R3
R2
R1
R0
G5
G4
G3
G2
G1
G0
B5
B4
B3
B2
B1
B0
6-bit RGB Interface (262K colors)
1st Transfer
2nd Transfer
3rd Transfer
Input Data
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
Write Data
Register
WD
17
WD
16
WD
15
WD
14
WD
13
WD
12
WD
11
WD
10
WD
9
WD
8
WD
7
WD
6
WD
5
WD
4
WD
3
WD
2
WD
1
WD
0
GRAM Data &
RGB Mapping
R5
R4
R3
R2
R1
R0
G5
G4
G3
G2
G1
G0
B5
B4
B3
B2
B1
B0
Figure14 RGB Interface Data Format
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 38 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
7.5.1. RGB Interface
The display operation via the RGB interface is synchronized with the VSYNC, HSYNC, and DOTCLK signals.
The RGB interface transfers the updated data to GRAM with the high-speed write function and the update
area is defined by the window address function. The back porch and front porch are used to set the RGB
interface timing.
VSYNC
Back porch
period (BP[3:0])
RAM data display area
Moving picture
display area
Display period
(NL[4:0]
Front porch
period (FP[3:0])
HSYNC
Note 1: Front porch period continues until
the next input of VSYNC.
DOTCLK
Note 2: Input DOTCLK throughout the
operation.
ENABLE
Note 3: Supply the VSYNC, HSYNC and
DOTCLK with frequency that can meet the
resolution requirement of panel.
DB[17:0]
Figure15 GRAM Access Area by RGB Interface
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 39 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
7.5.2. RGB Interface Timing
The timing chart of 18-/16-bit RGB interface mode is shown as follows.
1 frame
Back porch
VSYNC
Front porch
VLW >= 1H
HSYNC
DOTCLK
ENABLE
DB[17:0]
HLW >= 3 DOTCLK
//
HSYNC
1H
//
DOTCLK
DTST >= HLW
ENABLE
//
DB[17:0]
Valid data
VLW: VSYNC low period
HLW: HSYNC low period
DTST: data transfer startup time
Note 1: Use the high speed write mode (HWM=1) to write data through the RGB interface.
Figure16 Timing Chart of Signals in 18-/16-bit RGB Interface Mode
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 40 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
The timing chart of 6-bit RGB interface mode is shown as follows.
1 frame
Back porch
VSYNC
Front porch
VLW >= 1H
HSYNC
DOTCLK
ENABLE
DB[17:12]
HLW >= 3 DOTCLK
//
HSYNC
1H
//
DOTCLK
DTST >= HLW
ENABLE
//
R G B R G B
//
B R G B
DB[17:12]
Valid data
VLW: VSYNC low period
HLW: HSYNC low period
DTST: data transfer startup time
Note 1: Use the high speed write mode (HWM=1) to write data through the RGB interface.
Note 2) In 6-bit RGB interface mode, each dot of one pixel (R, G and B) is transferred in synchronization with
DOTCLKs.
Note 3) In 6-bit RGB interface mode, set the cycles of VSYNC, HSYNC and ENABLE to 3 multiples of DOTCLKs.
Figure17 Timing chart of signals in 6-bit RGB interface mode
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 41 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
7.5.3. Moving Picture Mode
ILI9325 has the RGB interface to display moving picture and incorporates GRAM to store display data, which
has following merits in displaying a moving picture.
• The window address function defined the update area of GRAM.
• Only the moving picture area of GRAM is updated.
• When display the moving picture in RGB interface mode, the DB[17:0] can be switched as system
interface to update still picture area and registers, such as icons.
RAM access via a system interface in RGB-I/F mode
ILI9325 allows GRAM access via the system interface in RGB interface mode. In RGB interface mode, data
are written to the internal GRAM in synchronization with DOTCLK and ENABLE signals. When write data to
the internal GRAM by the system interface, set ENABLE to terminate the RGB interface and switch to the
system interface to update the registers (RM = “0”) and the still picture of GRAM. When restart RAM access in
RGB interface mode, wait one read/write cycle and then set RM = “1” and the index register to R22h to start
accessing RAM via the RGB interface. If RAM accesses via two interfaces conflicts, there is no guarantee that
data are written to the internal GRAM.
The following figure illustrates the operation of the ILI9325 when displaying a moving picture via the RGB
interface and rewriting the still picture RAM area via the system interface.
Still Picture Area
Moving
Picture Area
Update
a frame
Update a
frame
VSYNC
ENABLE
DOTCLK
DB[17:0]
Set
IR to
R22h
Update
moving
picture
area
Set
RM=0
Set
AD[15:0]
Set
IR to
R22h
Update display data in
other than the moving
picture area
Set
AD[15:0]
Set
RM=1
Set
IR to
R22h
Update
moving
picture
area
Figure18 Example of update the still and moving picture
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 42 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
7.5.4. 6-bit RGB Interface
The 6-bit RGB interface is selected by setting the RIM[1:0] bits to “10”. The display operation is synchronized
with VSYNC, HSYNC, and DOTCLK signals. Display data are transferred to the internal GRAM in
synchronization with the display operation via 6-bit RGB data bus (DB[17:12]) according to the data enable
signal (ENABLE). Unused pins (DB[11:0]) must be fixed at either IOVcc or DGND level. Registers can be set
by the system interface (i80/SPI).
RGB interface with 6-bit data bus
1st Transfer
2nd Transfer
3rd Transfer
Input Data
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
RGB Assignment
R5
R4
R3
R2
R1
R0
G5
G4
G3
G2
G1
G0
B5
B4
B3
B2
B1
B0
Data transfer synchronization in 6-bit RGB interface mode
ILI9325 has data transfer counters to count the first, second, third data transfers in 6-bit RGB interface mode.
The transfer counter is always reset to the state of first data transfer on the falling edge of VSYNC. If a
mismatch arises in the number of each data transfer, the counter is reset to the state of first data transfer at
the start of the frame (i.e. on the falling edge of VSYNC) to restart data transfer in the correct order from the
next frame. This function is expedient for moving picture display, which requires consecutive data transfer in
light of minimizing effects from failed data transfer and enabling the system to return to a normal state.
Note that internal display operation is performed in units of pixels (RGB: taking 3 inputs of DOTCLK).
Accordingly, the number of DOTCLK inputs in one frame period must be a multiple of 3 to complete data
transfer correctly. Otherwise it will affect the display of that frame as well as the next frame.
HSYNC
ENABLE
DOTCLK
DB[17:12]
st
nd
rd
1st 2nd 3rd 1st 2nd 3rd 1 2 3 1st 2nd 3rd
Transfer synchronization
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 43 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
7.5.5. 16-bit RGB Interface
The 16-bit RGB interface is selected by setting the RIM[1:0] bits to “01”. The display operation is synchronized
with VSYNC, HSYNC, and DOTCLK signals. Display data are transferred to the internal RAM in
synchronization with the display operation via 16-bit RGB data bus (DB17-13, DB11-1) according to the data
enable signal (ENABLE). Registers are set only via the system interface.
16-bit RGB Interface (65K colors)
Input Data
DB
17
DB
16
DB
15
DB
14
DB
13
DB
11
DB
10
DB
9
DB
8
DB
7
DB
6
DB
5
DB
4
DB
3
DB
2
DB
1
Write Data
Register
WD
17
WD
16
WD
15
WD
14
WD
13
WD
11
WD
10
WD
9
WD
8
WD
7
WD
6
WD
5
WD
4
WD
3
WD
2
WD
1
GRAM Data &
RGB Mapping
R5
R4
R3
R2
R1
G5
G4
G3
G2
G1
G0
B5
B4
B3
B2
B1
R0
B0
7.5.6. 18-bit RGB Interface
The 18-bit RGB interface is selected by setting the RIM[1:0] bits to “00”. The display operation is synchronized
with VSYNC, HSYNC, and DOTCLK signals. Display data are transferred to the internal RAM in
synchronization with the display operation via 18-bit RGB data bus (DB[17:0]) according to the data enable
signal (ENABLE). Registers are set only via the system interface.
RGB interface with 18-bit data bus
Input Data
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
DB
11
DB
10
DB
9
DB
8
DB
7
DB
6
DB
5
DB
4
DB
3
DB
2
DB
1
DB
0
RGB Assignment
R5
R4
R3
R2
R1
R0
G5
G4
G3
G2
G1
G0
B5
B4
B3
B2
B1
B0
Notes in using the RGB Input Interface
1. The following are the functions not available in RGB Input Interface mode.
Function
Partial display
Scroll function
Interlaced scan
Graphics operation function
RGB interface
Not available
Not available
Not available
Not available
I80 system interface
Available
Available
Available
Available
2. VSYNC, HSYNC, and DOTCLK signals must be supplied throughout a display operation period.
3. The periods set with the NO[1:0] bits (gate output non-overlap period), STD[1:0] bits (source output delay
period) and EQ[1:0] bits (equalization period) are not based on the internal clock but based on DOTCLK in
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 44 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
RGB interface mode.
4. In 6-bit RGB interface mode, each of RGB dots is transferred in synchronization with a DOTCLK input. In
other words, it takes 3 DOTCLK inputs to transfer one pixel. Be sure to complete data transfer in units of 3
DOTCLK inputs in 6-bit RGB interface mode.
5. In 6-bit RGB interface mode, data of one pixel, which consists of RGB dots, are transferred in units of
3 DOTCLK. Accordingly, set the cycle of each signal in 6-bit interface mode (VSYNC, HSYNC, ENABLE,
DB[17:0]) to contain DOTCLK inputs of a multiple of 3 to complete data transfer in units of pixels.
6. When switching from the internal operation mode to the RGB Input Interface mode, or the other way around,
follow the sequence below.
7. In RGB interface mode, the front porch period continues until the next VSYNC input is detected after
drawing one frame.
8. In RGB interface mode, a RAM address (AD[15:0]) is set in the address counter every frame on the falling
edge of VSYNC.
Internal clock operation
to RGB I/F
RGB I/F to Internal clock
operation
Internal clock operation
RGB Interface Operation
Internal clock
operation
HWM = 1, AM=0
* SPI interface can
be used to set the
registers and data
Set AD[15:0]
Set RGB Interface mode
DM[1:0]=01 and RM=1
Note
Set IR to R22h
(GRAM data write)
* DM[1:0] and
RM become
enable after
completion of
display 1 frame
Set Internal Clock
Operation mode
DM[1:0]=00 and RM=0
RGB Interface
(Display operation in
synchronization with
VSYNC, HSYNC,
DOTCLK)
Wait for more than 1 frame
* DM[1:0] and RM
become enable after
completion of
display 1 frame
Internal clock operation
Display operation in
synchronization with
internal clock
Wait for more than 1 frame
Write data
through RGB I/F
RGB Interface
(Display operation in
synchronization with VSYNC,
HSYNC, DOTCLK)
RGB Interface Operation
Note: Input RGB Interface signals (VSYNC, HSYNC, DOTCLK)
before setting DM[1;0] and RM to the RGB interface mode
Figure19 Internal clock operation/RGB interface mode switching
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 45 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
Write data through RGB
interface to write data
through system interface
ILI9325
Write data through system
interface to write data
through RGB interface
System Interface operation
RGB Interface operation
Write data to GRAM
through system interface
Set DM[1:0]=01, RM=0
with RGB interface mode
HWM=1/0
HWM=1/0
Set AD[15;0]
Set AD[15;0]
Set DM[1:0]=01, RM=1
with RGB interface mode
Set IR to R22h
(GRAM data write)
Set IR to R22h
(GRAM data write)
Write data to GRAM
through system interface
RGB Interface operation
System Interface operation
Figure20 GRAM access between system interface and RGB interface
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 46 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
7.6. Interface Timing
The following are diagrams of interfacing timing with LCD panel control signals in internal operation and RGB
interface modes.
//
VSYNC
//
HSYNC
DOTCLK
//
ENABLE
//
//
DB[17:0]
1
2
3
4
5
318 319
320
1
2
3
4
FLM
G1
…..
G2
G320
S[720:1]
//
1
2
3
4
5
318 319
320
VCOM
Figure21 Relationship between RGB I/F signals and LCD Driving Signals for Panel
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 47 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
8. Register Descriptions
8.1. Registers Access
ILI9325 adopts 18-bit bus interface architecture for high-performance microprocessor. All the functional
blocks of ILI9325 starts to work after receiving the correct instruction from the external microprocessor by the
18-, 16-, 9-, 8-bit interface. The index register (IR) stores the register address to which the instructions and
display data will be written. The register selection signal (RS), the read/write signals (nRD/nWR) and data
bus D17-0 are used to read/write the instructions and data of ILI9325. The registers of the ILI9325 are
categorized into the following groups.
1. Specify the index of register (IR)
2. Read a status
3. Display control
4. Power management Control
5. Graphics data processing
6. Set internal GRAM address (AC)
7. Transfer data to/from the internal GRAM (R22)
8. Internal grayscale γ-correction (R30 ~ R39)
Normally, the display data (GRAM) is most often updated, and in order since the ILI9325 can update internal
GRAM address automatically as it writes data to the internal GRAM and minimize data transfer by using the
window address function, there are fewer loads on the program in the microprocessor. As the following figure
shows, the way of assigning data to the 16 register bits (D[15:0]) varies for each interface. Send registers in
accordance with the following data transfer format.
Serial Peripheral Interface for register access
SPI Input Data
D
15
D
14
D
13
D
12
D
11
D
10
D
9
D
8
D
7
D
6
D
5
D
4
D
3
D
2
D
1
D
0
Register Data
D
15
D
14
D
13
D
12
D
11
D
10
D
9
D
8
D
7
D
6
D
5
D
4
D
3
D
2
D
1
D
0
Figure22 Register Setting with Serial Peripheral Interface (SPI)
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 48 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
i80/M68 system 18-bit data bus interface
Data Bus
(DB[17:0])
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
DB
11
DB
10
Register Bit
(D[15:0])
D15
D14
D13
D12
D11
D10
D9
DB
9
DB
8
DB
7
DB
6
DB
5
DB
4
DB
3
DB
2
DB
1
D8
D7
D6
D5
D4
D3
D2
D1
D0
DB
0
i80/M68 system 16-bit data bus interface
Data Bus
(DB[17:10]),
(DB[8:1])
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
DB
11
DB
10
DB
8
DB
7
DB
6
DB
5
DB
4
DB
3
DB
2
DB
1
Register Bit
(D[15:0])
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
DB
17
DB
16
DB
15
2nd Transfer
DB
DB
DB
14
13
12
DB
11
DB
10
D7
D6
D5
D4
D1
D0
DB
12
DB
11
DB
10
D2
D1
D0
i80/M68 system 9-bit data bus interface
Data Bus
(DB[17:9])
DB
17
DB
16
DB
15
1st Transfer
DB
DB
DB
14
13
12
DB
11
DB
10
Register Bit
(D[15:0])
D15
D14
D13
D12
D9
D8
D11
D10
DB
9
D3
D2
DB
9
i80/M68 system 8-bit data bus interface/Serial peripheral interface (2/3 transmission)
Data Bus
(DB[17:10])
DB
17
DB
16
DB
15
1st Transfer
DB
DB
14
13
DB
12
DB
11
DB
10
DB
17
DB
16
DB
15
Register Bit
(D[15:0])
D15
D14
D13
D12
D10
D9
D8
D7
D6
D5
D11
2nd Transfer
DB
DB
14
13
D4
D3
Figure23 Register setting with i80 System Interface
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 49 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
i80 18-/16-bit System Bus Interface Timing
(a) Write to register
nCS
RS
nRD
nWR
DB[17:0]
Write register “index”
Write register “data”
(b) Read from register
nCS
RS
nRD
nWR
DB[17:0]
Write register “index”
Read register “data”
i80 9-/8-bit System Bus Interface Timing
(a) Write to register
nCS
RS
nRD
nWR
DB[17:10]
“00h”
Write register “index”
Write register
“high byte data”
Write register
“low byte data”
(b) Read from register
nCS
RS
nRD
nWR
DB[17:10]
“00h”
Write register “index”
Read register
“high byte data”
Read register
“low byte data”
Figure 24 Register Read/Write Timing of i80 System Interface
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 50 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
8.2. Instruction Descriptions
No.
Registers Name
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
IR
Index Register
R/W RS
W
0
-
-
-
-
-
-
-
-
ID7
ID6
ID5
ID4
ID3
ID2
ID1
ID0
SR
Status Read
R
0
L7
L6
L5
L4
L3
L2
L1
L0
0
0
0
0
0
0
0
0
00h Driver Code Read
R
1
1
0
0
1
0
0
1
0
0
0
1
0
0
0
1
0
01h Driver Output Control 1
W
1
0
0
0
0
0
SM
0
SS
0
0
0
0
0
0
0
0
02h LCD Driving Control
W
1
0
0
0
0
0
0
BC0
EOR
0
0
0
0
0
0
0
0
03h Entry Mode
W
1
TRI
DFM
0
BGR
0
DACKE
HWM
0
0
0
I/D1
I/D0
AM
0
0
0
04h Resize Control
W
1
0
0
0
0
0
0
RCV1
RCV0
0
0
RCH1
RCH0
0
0
RSZ1
RSZ0
07h Display Control 1
W
1
0
0
PTDE1
PTDE0
0
0
0
BASEE
0
0
GON
DTE
CL
0
D1
D0
08h Display Control 2
W
1
0
0
0
0
FP3
FP2
FP1
FP0
0
0
0
0
BP3
BP2
BP1
BP0
09h Display Control 3
W
1
0
0
0
0
0
PTS2
PTS1
PTS0
0
0
PTG1
PTG0
ISC3
ISC2
ISC1
ISC0
0Ah Display Control 4
W
1
0
0
0
0
0
0
0
0
0
0
0
0
FMARKOE
FMI2
FMI1
FMI0
0Ch RGB Display Interface Control 1
W
1
0
ENC2
ENC1
ENC0
0
0
0
RM
0
0
DM1
DM0
0
0
RIM1
RIM0
0Dh Frame Maker Position
W
1
0
0
0
0
0
0
0
FMP8
FMP7
FMP6
FMP5
FMP4
FMP3
FMP2
FMP1
FMP0
0Fh RGB Display Interface Control 2
W
1
0
0
0
0
0
0
0
0
0
0
0
VSPL
HSPL
0
DPL
EPL
10h Power Control 1
W
1
0
0
0
SAP
0
BT2
BT1
BT0
APE
AP2
AP1
AP0
0
DSTB
SLP
STB
11h Power Control 2
W
1
0
0
0
0
0
DC12
DC11
DC10
0
DC02
DC01
DC00
0
VC2
VC1
VC0
12h Power Control 3
W
1
0
0
0
0
0
0
0
0
VCIRE
0
0
PON
VRH3
VRH2
VRH1
VRH0
13h Power Control 4
W
1
0
0
0
VDV4
VDV3
VDV2
VDV1
VDV0
0
0
0
0
0
0
0
0
20h Horizontal GRAM Address Set
W
1
0
0
0
0
0
0
0
0
AD7
AD6
AD5
AD4
AD3
AD2
AD1
AD0
21h Vertical
W
1
0
0
0
0
0
0
0
AD16
AD15
AD14
AD13
AD12
AD11
AD10
AD9
AD8
W
1
GRAM Address Set
22h Write Data to GRAM
RAM write data (WD17-0) / read data (RD17-0) bits are transferred via different data bus lines according to the selected interfaces.
29h Power Control 7
W
1
0
0
0
0
0
0
0
0
0
0
VCM5
VCM4
VCM3
VCM2
VCM1
VCM0
2Bh Frame Rate and Color Control
W
1
0
0
0
0
0
0
0
0
0
0
0
0
FRS[3]
FRS[2]
FRS[1]
FRS[0]
30h Gamma Control 1
W
1
0
0
0
0
0
KP1[2]
KP1[1]
KP1[0]
0
0
0
0
0
KP0[2]
KP0[1]
KP0[0]
31h Gamma Control 2
W
1
0
0
0
0
0
KP3[2]
KP3[1]
KP3[0]
0
0
0
0
0
KP2[2]
KP2[1]
KP2[0]
32h Gamma Control 3
W
1
0
0
0
0
0
KP5[2]
KP5[1]
KP5[0]
0
0
0
0
0
KP4[2]
KP4[1]
KP4[0]
35h Gamma Control 4
W
1
0
0
0
0
0
RP1[2]
RP1[1]
RP1[0]
0
0
0
0
0
RP0[2]
RP0[1]
RP0[0]
36h Gamma Control 5
W
1
0
0
0
VRP1[4]
VRP1[3]
0
0
0
0
VRP0[3]
37h Gamma Control 6
W
1
0
0
0
0
0
VRP1[2] VRP1[1] VRP1[0]
KN1[2]
KN1[1]
KN1[0]
0
0
0
0
0
VRP0[2] VRP0[1] VRP0[0]
KN0[2]
KN0[1]
KN0[0]
38h Gamma Control 7
W
1
0
0
0
0
0
KN3[2]
KN3[1]
KN3[0]
0
0
0
0
0
KN2[2]
KN2[1]
KN2[0]
39h Gamma Control 8
W
1
0
0
0
0
0
KN5[2]
KN5[1]
KN5[0]
0
0
0
0
0
KN4[2]
KN4[1]
KN4[0]
3Ch Gamma Control 9
W
1
0
0
0
0
0
RN1[2]
RN1[1]
RN1[0]
0
0
0
0
0
RN0[2]
RN0[1]
RN0[0]
3Dh Gamma Control 10
W
1
0
0
0
VRN1[4]
VRN1[3]
0
0
0
0
VRN0[3]
VRN1[2] VRN1[1] VRN1[0]
VRN0[2] VRN0[1] VRN0[0]
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written
permission of ILI Technology Corp.
Page 51 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
No.
50h
Registers Name
Horizontal Address Start
R/W RS
ILI9325
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
0
HSA7
HSA6
HSA5
HSA4
HSA3
HSA2
HSA1
HSA0
HEA0
W
1
0
0
0
0
0
0
0
51h Horizontal Address End Position
W
1
0
0
0
0
0
0
0
0
HEA7
HEA6
HEA5
HEA4
HEA3
HEA2
HEA1
52h Vertical Address Start Position
W
1
0
0
0
0
0
0
0
VSA8
VSA7
VSA6
VSA5
VSA4
VSA3
VSA2
VSA1
VSA0
53h Vertical Address End Position
W
1
0
0
0
0
0
0
0
VEA8
VEA7
VEA6
VEA5
VEA4
VEA3
VEA2
VEA1
VEA0
60h Driver Output Control 2
W
1
GS
0
NL5
NL4
NL3
NL2
NL1
NL0
0
0
SCN5
SCN4
SCN3
SCN2
SCN1
SCN0
Position
61h Base Image Display Control
W
1
0
0
0
0
0
0
0
0
0
0
0
0
0
NDL
VLE
REV
6Ah Vertical Scroll Control
W
1
0
0
0
0
0
0
0
VL8
VL7
VL6
VL5
VL4
VL3
VL2
VL1
VL0
80h Partial Image 1 Display Position
W
1
0
0
0
0
0
0
0
PTDP08 PTDP07 PTDP06 PTDP05
PTDP04
PTDP03
PTDP02 PTDP01 PTDP00
81h Partial Image 1 Area (Start Line)
W
1
0
0
0
0
0
0
0
PTSA08 PTSA07 PTSA06 PTSA05
PTSA04
PTSA03
PTSA02 PTSA01 PTSA00
82h Partial Image 1 Area (End Line)
W
1
0
0
0
0
0
0
0
PTEA08 PTEA07 PTEA06 PTEA05
PTEA04
PTEA03
PTEA02 PTEA01 PTEA00
83h Partial Image 2 Display Position
W
1
0
0
0
0
0
0
0
PTDP18 PTDP17 PTDP16 PTDP15
PTDP14
PTDP13
PTDP12 PTDP11 PTDP10
84h Partial Image 2 Area (Start Line)
W
1
0
0
0
0
0
0
0
PTSA18 PTSA17 PTSA16 PTSA15
PTSA14
PTSA13
PTSA12 PTSA11 PTSA10
85h Partial Image 2 Area (End Line)
W
1
0
0
0
0
0
0
0
PTEA18 PTEA17 PTEA16 PTEA15
PTEA14
PTEA13
PTEA12 PTEA11 PTEA10
90h Panel Interface Control 1
W
1
0
0
0
0
0
0
DIVI1
DIVI00
0
0
0
0
RTNI3
RTNI2
RTNI1
92h Panel Interface Control 2
W
1
0
0
0
0
0
NOWI2
NOWI1
NOWI0
0
0
0
0
0
0
0
RTNI0
0
95h Panel Interface Control 4
W
1
0
0
0
0
0
DIVE1
DIVE0
0
0
A1h OTP VCM Programming Control
W
1
0
0
0
0
0
0
0
0
0
RTNE5
VCM_
OTP5
RTNE4
VCM_
OTP4
RTNE3
VCM_
OTP3
RTNE2
VCM_
OTP2
RTNE1
VCM_
OTP1
A2h OTP VCM Status and Enable
W
1
VCM_
D4
KEY
12
VCM_
D2
KEY
10
VCM_
D1
KEY
9
VCM_
D0
KEY
8
0
0
0
0
0
1
VCM_
D5
KEY
13
0
W
PGM_
CNT0
KEY
14
0
A5h OTP Programming ID Key
PGM_
CNT1
KEY
15
0
OTP_
PGM_EN
VCM_
D3
KEY
11
KEY
7
KEY
6
KEY
5
KEY
4
KEY
3
KEY
2
KEY
1
RTNE0
VCM_
OTP0
VCM_
EN
KEY
0
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written
permission of ILI Technology Corp.
Page 52 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
8.2.1. Index (IR)
R/W
RS
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
W
0
-
-
-
-
-
-
-
-
ID7
ID6
ID5
ID4
ID3
ID2
ID1
ID0
The index register specifies the address of register (R00h ~ RFFh) or RAM which will be accessed.
8.2.2. Status Read (RS)
R/W
RS
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
R
0
L7
L6
L5
L4
L3
L2
L1
L0
0
0
0
0
0
0
0
0
The SR bits represent the internal status of the ILI9325.
L[7:0] Indicates the position of driving line which is driving the TFT panel currently.
8.2.3. Start Oscillation (R00h)
R/W
RS
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
W
1
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
1
R
1
1
0
0
1
0
0
1
1
0
0
1
0
0
1
0
1
D4
D3
D2
D1
D0
0
0
0
0
0
The device code “9325”h is read out when read this register.
8.2.4. Driver Output Control (R01h)
R/W
RS
D15
W
1
0
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
0
0
0
0
SM
0
SS
0
0
0
SS: Select the shift direction of outputs from the source driver.
When SS = 0, the shift direction of outputs is from S1 to S720
When SS = 1, the shift direction of outputs is from S720 to S1.
In addition to the shift direction, the settings for both SS and BGR bits are required to change the
assignment of R, G, B dots to the source driver pins.
To assign R, G, B dots to the source driver pins from S1 to S720, set SS = 0.
To assign R, G, B dots to the source driver pins from S720 to S1, set SS = 1.
When changing SS or BGR bits, RAM data must be rewritten.
SM: Sets the gate driver pin arrangement in combination with the GS bit (R60h) to select the optimal scan
mode for the module.
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 53 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
SM
GS
Scan Direction
G319
G318
G317
TFT Panel
Odd-number
G1, G2, G3, G4, …,G316
G4
G3
G2
G1
G1 to G319
0
G2 to G320
0
Gate Output Sequence
G320
Even-number
ILI9325
G317, G318, G319, G320
ILI9325
G320
G319
G318
G317
Even-number
Odd-number
G320, G319, G318, …,
G4
G3
G2
G1
G1 to G319
1
G2 to G320
0
TFT Panel
G6, G5, G4, G3, G2, G1
ILI9325
Even-number
G320
TFT Panel
G1, G3, G5, G7, …,G311
G2
0
G313, G315, G317, G319
Odd-number
G1
ILI9325
G1 to G319
G2 to G320
1
G319
G2, G4, G6, G8, …,G312
G314, G316, G318, G320
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 54 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
Even-number
ILI9325
G320
TFT Panel
G320, G318, G316, …,
G10, G8, G6, G4, G2
G2
G319
1
Odd-number
G319, G317, G315, …,
G1 to G319
G2 to G320
1
G1
ILI9325
G9, G78, G5, G3, G1
8.2.5. LCD Driving Wave Control (R02h)
R/W
RS
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
W
1
0
0
0
0
0
1
B/C
EOR
0
0
0
0
0
0
0
0
.B/C 0 : Frame/Field inversion
1 : Line inversion
EOR: EOR = 1 and B/C=1 to set the line inversion.
8.2.6. Entry Mode (R03h)
R/W
RS
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
W
1
TRI
DFM
0
BGR
0
0
HWM
0
ORG
0
I/D1
I/D0
AM
0
0
0
AM Control the GRAM update direction.
When AM = “0”, the address is updated in horizontal writing direction.
When AM = “1”, the address is updated in vertical writing direction.
When a window area is set by registers R50h ~R53h, only the addressed GRAM area is updated based
on I/D[1:0] and AM bits setting.
I/D[1:0] Control the address counter (AC) to automatically increase or decrease by 1 when update one pixel
display data. Refer to the following figure for the details.
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 55 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
I/D[1:0] = 00
Horizontal : decrement
Vertical : decrement
I/D[1:0] = 01
Horizontal : increment
Vertical : decrement
E
AM = 0
Horizontal
E
B
B
E
AM = 1
Vertical
I/D[1:0] = 10
Horizontal : decrement
Vertical : increment
B
I/D[1:0] = 11
Horizontal : increment
Vertical : increment
B
E
E
B
ILI9325
B
E
B
B
E
E
Figure25 GRAM Access Direction Setting
ORG Moves the origin address according to the ID setting when a window address area is made. This
function is enabled when writing data with the window address area using high-speed RAM write.
ORG = “0”: The origin address is not moved. In this case, specify the address to start write operation
according to the GRAM address map within the window address area.
ORG = “1”: The original address “00000h” moves according to the I/D[1:0] setting.
Notes: 1. When ORG=1, only the origin address address”00000h” can be set in the RAM address set
registers R20h, and R21h.
2. In RAM read operation, make sure to set ORG=0.
BGR Swap the R and B order of written data.
BGR=”0”: Follow the RGB order to write the pixel data.
BGR=”1”: Swap the RGB data to BGR in writing into GRAM.
TRI When TRI = “1”, data are transferred to the internal RAM in 8-bit x 3 transfers mode via the 8-bit interface.
It is also possible to send data via the 16-bit interface or SPI in the transfer mode that realizes display in 262k
colors in combination with DFM bits. When not using these interface modes, be sure to set TRI = “0”.
DFM Set the mode of transferring data to the internal RAM when TRI = “1”. See the following figures for
details.
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 56 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
TRI
DFM
ILI9325
16-bit MPU System Interface Data Format
system 16-bit interface (1 transfers/pixel) 65,536 colors
0
*
1st Transfer
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
DB
11
DB
10
R5
R4
R3
R2
R1
R0
G5
G4
G3
DB
8
DB
7
DB
6
DB
5
DB
4
DB
3
DB
2
DB
1
G2
G1
G0
B5
B4
B3
B2
B1
B0
80-system 16-bit interface (2 transfers/pixel) 262,144 colors
1
0
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
DB
11
R5
R4
R3
R2
R1
R0
G5
1st Transfer
2nd Transfer
DB
DB
17
16
DB
10
DB
8
DB
7
DB
6
DB
5
DB
4
DB
3
DB
2
DB
1
G4
G3
G2
G1
G0
B5
B4
B3
B2
B1
B0
80-system 16-bit interface (2 transfers/pixel) 262,144 colors
1
1
1st Transfer
DB
DB
2
1
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
DB
11
R5
R3
R2
R1
R0
G5
G4
G3
R4
2nd Transfer
DB
10
DB
8
DB
7
DB
6
DB
5
DB
4
DB
3
DB
2
DB
1
G2
G1
G0
B5
B4
B3
B2
B1
B0
Figure26 16-bit MPU System Interface Data Format
TRI
DFM
8-bit MPU System Interface Data Format
system 8-bit interface (2 transfers/pixel) 65,536 colors
0
*
DB
17
DB
16
DB
15
R5
R4
R3
1st Transfer
DB
14
DB
13
DB
12
DB
11
DB
10
R2
R1
R0
G5
G4
G3
DB
17
DB
16
DB
15
G2
G1
2nd Transfer
DB
14
DB
13
DB
12
DB
11
DB
10
G0
B5
B4
B3
B2
B1
B0
80-system 8-bit interface (3 transfers/pixel) 262,144 colors
1
0
1st Transfer
DB
DB
11
10
DB
17
DB
16
DB
15
R5
R3
R2
R1
R4
2nd Transfer
DB
14
DB
13
DB
12
DB
11
DB
10
DB
17
DB
16
DB
15
R0
G5
G4
G3
G2
G1
G0
3rd Transfer
DB
14
DB
13
DB
12
DB
11
DB
10
B5
B4
B3
B2
B1
B0
80-system 8-bit interface (3 transfers/pixel) 262,144 colors
1
1
DB
17
DB
16
R5
R4
1st Transfer
DB
15
DB
14
DB
13
DB
12
DB
17
DB
16
R3
R2
R1
R0
G5
G4
2nd Transfer
DB
15
DB
14
DB
13
DB
12
DB
17
DB
16
G3
G2
G1
G0
B5
B4
3rd Transfer
DB
15
DB
14
DB
13
DB
12
B3
B2
B1
B0
Figure27 8-bit MPU System Interface Data Format
8.2.7. Resizing Control Register (R04h)
R/W
RS
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
W
1
0
0
0
0
0
0
RCV1
RCV0
0
0
RCH1
RCH0
0
0
RSZ1
RSZ0
RSZ[1:0] Sets the resizing factor.
When the RSZ bits are set for resizing, the ILI9325 writes the data according to the resizing factor
so that the original image is displayed in horizontal and vertical dimensions, which are contracted
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 57 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
according to the factor respectively. See “Resizing function”.
RCH[1:0] Sets the number of remainder pixels in horizontal direction when resizing a picture.
By specifying the number of remainder pixels by RCH bits, the data can be transferred without
taking the reminder pixels into consideration. Make sure that RCH = 2’h0 when not using the
resizing function (RSZ = 2’h0) or there are no remainder pixels.
RCV[1:0] Sets the number of remainder pixels in vertical direction when resizing a picture.
By specifying the number of remainder pixels by RCV bits, the data can be transferred without
taking the reminder pixels into consideration. Make sure that RCV = 2’h0 when not using the
resizing function (RSZ = 2’h0) or there are no remainder pixels.
RSZ[1:0]
00
01
10
11
Resizing factor
No resizing (x1)
x 1/2
Setting prohibited
x 1/4
RCH[1:0]
00
01
10
11
Number of remainder Pixels in Horizontal Direction
0 pixel*
1 pixel
2 pixel
3 pixel
RCV[1:0]
00
01
10
11
Number of remainder Pixels in Vertical Direction
0 pixel*
1 pixel
2 pixel
3 pixel
*1 pixel = 1RGB
8.2.8. Display Control 1 (R07h)
R/W
RS
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
W
1
0
0
PTDE1
PTDE0
0
0
0
BASEE
0
0
GON
DTE
CL
0
D1
D0
D[1:0] Set D[1:0]=”11” to turn on the display panel, and D[1:0]=”00” to turn off the display panel.
A graphics display is turned on the panel when writing D1 = “1”, and is turned off when writing
D1 = “0”.
When writing D1 = “0”, the graphics display data is retained in the internal GRAM and the
ILI9325 displays the data when writing D1 = “1”. When D1 = “0”, i.e. while no display is shown on the
panel, all source outputs becomes the GND level to reduce charging/discharging current, which is
generated within the LCD while driving liquid crystal with AC voltage.
When the display is turned off by setting D[1:0] = “01”, the ILI9325 continues internal display
operation. When the display is turned off by setting D[1:0] = “00”, the ILI9325 internal display
operation is halted completely. In combination with the GON, DTE setting, the D[1:0] setting controls
display ON/OFF.
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 58 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
D1
0
0
1
1
1
D0
0
1
0
1
1
BASEE
0
1
0
0
1
Source, VCOM Output
GND
GND
Non-lit display
Non-lit display
Base image display
ILI9325
ILI9325 internal operation
Halt
Operate
Operate
Operate
Operate
Note: 1. data write operation from the microcontroller is performed irrespective of the setting of D[1:0] bits.
2. The D[1:0] setting is valid on both 1st and 2nd displays.
3. The non-lit display level from the source output pins is determined by instruction (PTS).
CL When CL = “1”, the 8-color display mode is selected.
CL
0
1
Colors
262,144
8
GON and DTE Set the output level of gate driver G1 ~ G320 as follows
GON
0
0
1
1
DTE
0
1
0
1
G1 ~G320 Gate Output
VGH
VGH
VGL
Normal Display
BASEE
Base image display enable bit. When BASEE = “0”, no base image is displayed. The ILI9325 drives
liquid crystal at non-lit display level or displays only partial images. When BASEE = “1”, the base
image is displayed. The D[1:0] setting has higher priority over the BASEE setting.
PTDE[1:0]
Partial image 2 and Partial image 1 enable bits
PTDE1/0 = 0: turns off partial image. Only base image is displayed.
PTDE1/0 = 1: turns on partial image. Set the base image display enable bit to 0 (BASEE = 0).
8.2.9. Display Control 2 (R08h)
R/W
RS
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
W
1
0
0
0
0
FP3
FP2
FP1
FP0
0
0
0
0
BP3
BP2
BP1
BP0
FP[3:0]/BP[3:0]
The FP[3:0] and BP[3:0] bits specify the line number of front and back porch periods respectively.
When setting the FP[3:0] and BP[3:0] value, the following conditions shall be met:
BP + FP ≤ 16 lines
FP ≥ 2 lines
BP ≥ 2 lines
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 59 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
Set the BP[3:0] and FP[3:0] bits as below for each operation modes
Operation Mode
I80 System Interface Operation Mode
RGB interface Operation
VSYNC interface Operation
Number of lines for Front Porch
Number of lines for Back Porch
Setting Prohibited
Setting Prohibited
2 lines
3 lines
4 lines
5 lines
6 lines
7 lines
8 lines
9 lines
10 lines
11 lines
12 lines
13 lines
14 lines
Setting Prohibited
FP
BP+FP
BP ≥ 2 lines
BP ≥ 2 lines
BP ≥ 2 lines
FP ≥ 2 lines
FP ≥ 2 lines
FP ≥ 2 lines
FP +BP ≤ 16 lines
FP +BP ≤ 16 lines
FP +BP = 16 lines
Back Porch
Display
Area
VSYNC
FP[3:0]
BP[3:0]
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
BP
Front Porch
Note: The output timing to the LCD is delayed by 2
lines period from the input of synchronizing signal.
8.2.10. Display Control 3 (R09h)
R/W
RS
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
W
1
0
0
0
0
0
PTS2
PTS1
PTS0
0
0
PTG1
PTG0
ISC3
ISC2
ISC1
ISC0
ISC[3:0]: Specify the scan cycle interval of gate driver in non-display area when PTG[1:0]=”10” to select
interval scan. Then scan cycle is set as odd number from 0~29 frame periods. The polarity is
inverted every scan cycle.
ISC3
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
ISC3
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
ISC3
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
ISC3
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Scan Cycle
0 frame
1 frame
3 frame
5 frame
7 frame
9 frame
11 frame
13 frame
15 frame
17 frame
19 frame
21 frame
23 frame
25 frame
27 frame
29 frame
fFLM=60 Hz
17ms
50ms
84ms
117ms
150ms
184ms
217ms
251ms
284ms
317ms
351ms
384ms
418ms
451ms
484ms
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 60 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
PTG[1:0] Set the scan mode in non-display area.
PTG1
PTG0
Gate outputs in non-display area
Source outputs in non-display area
Vcom output
0
0
Normal scan
Set with the PTS[2:0] bits
VcomH/VcomL
0
1
Setting Prohibited
-
-
1
1
0
1
Interval scan
Set with the PTS[2:0] bits
-
VcomH/VcomL
-
Setting Prohibited
PTS[2:0]
Set the source output level in non-display area drive period (front/back porch period and blank area
between partial displays).
When PTS[2] = 1, the operation of amplifiers which generates the grayscales other than V0 and V63
are halted and the step-up clock frequency becomes half the normal frequency in non-display drive
period in order to reduce power consumption.
Source output level
Positive polarity
Negative polarity
V63
V0
Setting Prohibited Setting Prohibited
GND
GND
Hi-Z
Hi-Z
V63
V0
Setting Prohibited Setting Prohibited
GND
GND
Hi-Z
Hi-Z
PTS[2:0]
000
001
010
011
100
101
110
111
Grayscale amplifier
in operation
V63 to V0
V63 to V0
V63 to V0
V63 and V0
V63 and V0
V63 and V0
Step-up clock frequency
Register Setting (DC1, DC0)
Register Setting (DC1, DC0)
Register Setting (DC1, DC0)
frequency setting by DC1, DC0
frequency setting by DC1, DC0
frequency setting by DC1, DC0
Notes: 1. The power efficiency can be improved by halting grayscale amplifiers and slowing down the step-up clock frequency only in
non-display drive period.
2. The gate output level in non-lit display area drive period is determined by PTG[1:0].
8.2.11. Display Control 4 (R0Ah)
R/W
RS
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
W
1
0
0
0
0
0
0
0
0
0
0
0
0
FMARKOE
FMI2
FMI1
FMI0
FMI[2:0] Set the output interval of FMARK signal according to the display data rewrite cycle and data transfer
rate.
FMARKOE When FMARKOE=1, ILI9325 starts to output FMARK signal in the output interval set by FMI[2:0]
bits.
FMI[2:0]
000
001
011
101
Others
Output Interval
1 frame
2 frame
4 frame
6 frame
Setting disabled
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 61 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
8.2.12. RGB Display Interface Control 1 (R0Ch)
R/W
RS
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
W
1
0
ENC2
ENC1
ENC0
0
0
0
RM
0
0
DM1
DM0
0
0
RIM1
RIM0
RIM[1:0] Select the RGB interface data width.
RIM1
RIM0
0
0
0
1
18-bit RGB interface (1 transfer/pixel), DB[17:0]
16-bit RGB interface (1 transfer/pixel), DB[17:13] and DB[11:1]
1
1
0
1
6-bit RGB interface (3 transfers/pixel), DB[17:12]
Setting disabled
RGB Interface Mode
Note1: Registers are set only by the system interface.
Note2: Be sure that one pixel (3 dots) data transfer finished when interface switch.
DM[1:0] Select the display operation mode.
DM1
DM0
0
0
Display Interface
0
1
RGB interface
1
1
0
1
VSYNC interface
Setting disabled
Internal system clock
The DM[1:0] setting allows switching between internal clock operation mode and external display
interface operation mode. However, switching between the RGB interface operation mode and the
VSYNC interface operation mode is prohibited.
RM Select the interface to access the GRAM.
Set RM to “1” when writing display data by the RGB interface.
RM
Display State
Still pictures
Moving pictures
Interface for RAM Access
0
System interface/VSYNC interface
1
RGB interface
Operation Mode
Internal clock operation
RGB interface (1)
Rewrite still picture area while RGB interface
Displaying moving pictures.
Moving pictures
VSYNC interface
RAM Access (RM)
Display Operation Mode (DM[1:0]
System interface
(RM = 0)
RGB interface
(RM = 1)
System interface
(RM = 0)
System interface
(RM = 0)
Internal clock operation
(DM[1:0] = 00)
RGB interface
(DM[1:0] = 01)
RGB interface
(DM[1:0] = 01)
VSYNC interface
(DM[1:0] = 10)
Note 1: Registers are set only via the system interface or SPI interface.
Note 2: Refer to the flowcharts of “RGB Input Interface” section for the mode switch.
ENC[2:0] Set the GRAM write cycle through the RGB interface
ENC[2:0]
GRAM Write Cycle (Frame periods)
000
001
010
011
1 Frame
2 Frames
3 Frames
4 Frames
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 62 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
100
101
110
111
ILI9325
5 Frames
6 Frames
7 Frames
8 Frames
8.2.13. Frame Marker Position (R0Dh)
R/W
RS
D15
D14
D13
D12
D11
D10
D9
W
1
0
0
0
0
0
0
0
D8
D7
D6
D5
D4
D3
D2
D1
D0
FMP8 FMP7 FMP6 FMP5 FMP4 FMP3 FMP2 FMP1 FMP0
EMP[8:0] Sets the output position of frame cycle (frame marker).
When FMP[8:0]=0, a high-active pulse FMARK is output at the start of back porch period for one display line
period (1H).
Make sure the 9’h000 ≦ FMP ≦ BP+NL+FP
FMP[8:0]
9’h000
9’h001
9’h002
9’h003
.
.
.
9’h175
9’h176
9’h177
FMARK Output Position
0th line
1st line
2nd line
3rd line
.
.
.
373rd line
374th line
375th line
8.2.14. RGB Display Interface Control 2 (R0Fh)
R/W
RS
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
W
1
0
0
0
0
0
0
0
0
0
0
0
VSPL
HSPL
0
EPL
DPL
DPL: Sets the signal polarity of the DOTCLK pin.
DPL = “0” The data is input on the rising edge of DOTCLK
DPL = “1” The data is input on the falling edge of DOTCLK
EPL: Sets the signal polarity of the ENABLE pin.
EPL = “0” The data DB17-0 is written when ENABLE = “0”. Disable data write operation when
ENABLE = “1”.
EPL = “1” The data DB17-0 is written when ENABLE = “1”. Disable data write operation when
ENABLE = “0”.
HSPL: Sets the signal polarity of the HSYNC pin.
HSPL = “0” Low active
HSPL = “1” High active
VSPL: Sets the signal polarity of the VSYNC pin.
VSPL = “0” Low active
VSPL = “1” High active
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 63 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
8.2.15. Power Control 1 (R10h)
R/W
RS
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
W
1
0
0
0
SAP
0
BT2
BT1
BT0
APE
AP2
AP1
AP0
0
DSTB
SLP
STB
SLP: When SLP = 1, ILI9325 enters the sleep mode and the display operation stops except the RC oscillator
to reduce the power consumption. In the sleep mode, the GRAM data and instructions cannot be
updated except the following two instructions.
a. Exit sleep mode (SLP = “0”)
b. Start oscillation
STB: When STB = 1, ILI9325 enters the standby mode and the display operation stops except the GRAM
power supply to reduce the power consumption. In the sleep mode, the GRAM data and instructions
cannot be updated except the following two instructions.
a. Exit standby mode (STB = “0”)
b. Start oscillation
DSTB: When DSTB = 1, the ILI9325 enters the deep standby mode. In deep standby mode, the internal logic
power supply is turned off to reduce power consumption. The GRAM data and instruction setting are not
maintained when the ILI9325 enters the deep standby mode, and they must be reset after exiting deep
standby mode.
AP[2:0]: Adjusts the constant current in the operational amplifier circuit in the LCD power supply circuit. The
larger constant current enhances the drivability of the LCD, but it also increases the current
consumption. Adjust the constant current taking the trade-off into account between the display quality
and the current consumption. In no-display period, set AP[2:0] = “000” to halt the operational amplifier
circuits and the step-up circuits to reduce current consumption.
AP[2:0]
Gamma driver amplifiers
Source driver amplifiers
000
Halt
Halt
001
1.00
1.00
010
1.00
0.75
011
1.00
0.50
100
0.75
1.00
101
0.75
0.75
110
0.75
0.50
111
0.50
0.50
SAP: Source Driver output control
SAP=0, Source driver is disabled.
SAP=1, Source driver is enabled.
When starting the charge-pump of LCD in the Power ON stage, make sure that SAP=0, and set the
SAP=1, after starting up the LCD power supply circuit.
APE: Power supply enable bit.
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 64 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
Set APE = “1” to start the generation of power supply according to the power supply startup sequence.
BT[3:0]: Sets the factor used in the step-up circuits.
Select the optimal step-up factor for the operating voltage. To reduce power consumption, set a smaller
factor.
BT[2:0]
DDVDH
VCL
3’h0
Vci1 x 2
- Vci1
3’h1
3’h2
Vci1 x 2
VGH
VGL
- Vci1 x 5
Vci1 x 6
- Vci1
- Vci1 x 4
- Vci1 x 3
3’h3
3’h4
- Vci1 x 5
Vci1 x 2
- Vci1
Vci1 x 5
- Vci1 x 4
3’h5
- Vci1 x 3
3’h6
- Vci1 x 4
3’h7
Vci1 x 2
- Vci1
Vci1 x 4
- Vci1 x 3
Notes: 1. Connect capacitors to the capacitor connection pins when generating DDVDH, VGH, VGL and VCL levels.
2. Make sure DDVDH = 6.0V (max.), VGH = 15.0V (max.), VGL = – 12.5V (max) and VCL= -3.0V (max.)
8.2.16. Power Control 2 (R11h)
R/W
RS
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
W
1
0
0
0
0
0
DC12
DC11
DC10
0
DC02
DC01
DC00
0
VC2
VC1
VC0
VC[2:0] Sets the ratio factor of Vci to generate the reference voltages Vci1.
VC2
VC1
VC0
Vci1 voltage
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0.95 x Vci
0.90 x Vci
0.85 x Vci
0.80 x Vci
0.75 x Vci
0.70 x Vci
Disabled
1.0 x Vci
DC0[2:0]: Selects the operating frequency of the step-up circuit 1. The higher step-up operating frequency
enhances the drivability of the step-up circuit and the quality of display but increases the current
consumption. Adjust the frequency taking the trade-off between the display quality and the current
consumption into account.
DC1[2:0]: Selects the operating frequency of the step-up circuit 2. The higher step-up operating frequency
enhances the drivability of the step-up circuit and the quality of display but increases the current
consumption. Adjust the frequency taking the trade-off between the display quality and the current
consumption into account.
DC02
DC01
DC00
Step-up circuit1
step-up frequency (fDCDC1)
DC12
DC11
DC10
Step-up circuit2
step-up frequency (fDCDC2)
0
0
0
Fosc
0
0
0
Fosc / 4
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 65 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
0
0
0
1
1
1
1
0
1
1
0
0
1
1
1
0
1
0
1
0
1
Fosc / 2
Fosc / 4
Fosc / 8
Fosc / 16
Fosc / 32
Fosc / 64
Halt step-up circuit 1
0
0
0
1
1
1
1
0
1
1
0
0
1
1
ILI9325
1
0
1
0
1
0
1
Fosc / 8
Fosc / 16
Fosc / 32
Fosc / 64
Fosc / 128
Fosc / 256
Halt step-up circuit 2
Note: Be sure fDCDC1≥fDCDC2 when setting DC0[2:0] and DC1[2:0].
8.2.17. Power Control 3 (R12h)
R/W
RS
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
W
1
0
0
0
0
0
0
0
0
VCIRE
0
0
PON
VRH3
VRH2
VRH1
VRH0
VRH[3:0] Set the amplifying rate (1.6 ~ 1.9) of Vci applied to output the VREG1OUT level, which is a
reference level for the VCOM level and the grayscale voltage level.
VCIRE: Select the external reference voltage Vci or internal reference voltage VCIR.
VCIRE=0
VCIRE =1
External reference voltage Vci (default)
Internal reference voltage 2.5V
VCIRE =0
VCIRE =1
VRH3
VRH2
VRH1
VRH0
VREG1OUT
VRH3
VRH2
VRH1
VRH0
VREG1OUT
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Halt
Vci x 2.00
Vci x 2.05
Vci x 2.10
Vci x 2.20
Vci x 2.30
Vci x 2.40
Vci x 2.40
Vci x 1.60
Vci x 1.65
Vci x 1.70
Vci x 1.75
Vci x 1.80
Vci x 1.85
Vci x 1.90
Vci x 1.95
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Halt
2.5V x 2.00 = 5.000V
2.5V x 2.05 = 5.125V
2.5V x 2.10 = 5.250V
2.5V x 2.20 = 5.500V
2.5V x 2.30 = 5.750V
2.5V x 2.40 = 6.000V
2.5V x 2.40 = 6.000V
2.5V x 1.60 = 4.000V
2.5V x 1.65 = 4.125V
2.5V x 1.70 = 4.250V
2.5V x 1.75 = 4.375V
2.5V x 1.80 = 4.500V
2.5V x 1.85 = 4.625V
2.5V x 1.90 = 4.750V
2.5V x 1.95 = 4.875V
When VCI<2.5V, Internal reference voltage will be same as VCI.
Make sure that VC and VRH setting restriction: VREG1OUT ≦ (DDVDH - 0.5)V.
PON: Control ON/OFF of circuit3 (VGL) output.
PON=0
PON=1
VGL output is disable
VGL output is enable
8.2.18. Power Control 4 (R13h)
R/W
RS
D15
D14
D13
W
1
0
0
0
D12
D11
VDV4 VDV3
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
VDV2
VDV1
VDV0
0
0
0
0
0
0
0
0
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 66 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
VDV[4:0] Select the factor of VREG1OUT to set the amplitude of Vcom alternating voltage from 0.70 to 1.24 x
VREG1OUT .
VDV4 VDV3 VDV2 VDV1 VDV0
VCOM amplitude
0
0
0
0
0
VREG1OUT x 0.70
0
0
0
0
1
VREG1OUT x 0.72
0
0
0
1
0
VREG1OUT x 0.74
0
0
0
1
1
VREG1OUT x 0.76
0
0
1
0
0
VREG1OUT x 0.78
0
0
1
0
1
VREG1OUT x 0.80
0
0
1
1
0
VREG1OUT x 0.82
0
0
1
1
1
VREG1OUT x 0.84
0
1
0
0
0
VREG1OUT x 0.86
0
1
0
0
1
VREG1OUT x 0.88
0
1
0
1
0
VREG1OUT x 0.90
0
1
0
1
1
VREG1OUT x 0.92
0
1
1
0
0
VREG1OUT x 0.94
0
1
1
0
1
VREG1OUT x 0.96
0
1
1
1
0
VREG1OUT x 0.98
0
1
1
1
1
VREG1OUT x 1.00
VDV4 VDV3 VDV2 VDV1 VDV0
VCOM amplitude
1
0
0
0
0
VREG1OUT x 0.94
1
0
0
0
1
VREG1OUT x 0.96
1
0
0
1
0
VREG1OUT x 0.98
1
0
0
1
1
VREG1OUT x 1.00
1
0
1
0
0
VREG1OUT x 1.02
1
0
1
0
1
VREG1OUT x 1.04
1
0
1
1
0
VREG1OUT x 1.06
1
0
1
1
1
VREG1OUT x 1.08
1
1
0
0
0
VREG1OUT x 1.10
1
1
0
0
1
VREG1OUT x 1.12
1
1
0
1
0
VREG1OUT x 1.14
1
1
0
1
1
VREG1OUT x 1.16
1
1
1
0
0
VREG1OUT x 1.18
1
1
1
0
1
VREG1OUT x 1.20
1
1
1
1
0
VREG1OUT x 1.22
1
1
1
1
1
VREG1OUT x 1.24
Set VDV[4:0] to let Vcom amplitude less than 6V.
8.2.19. GRAM Horizontal/Vertical Address Set (R20h, R21h)
R/W
RS
D15
D14
D13
D12
D11
D10
D9
D8
W
1
0
0
0
0
0
0
0
0
W
1
0
0
0
0
0
0
0
AD16
D7
D6
D5
D4
D3
D2
D1
D0
AD7
AD6
AD5
AD4
AD3
AD2
AD1
AD0
AD15
AD14
AD13
AD12
AD11
AD10
AD9
AD8
AD[16:0] Set the initial value of address counter (AC).
The address counter (AC) is automatically updated in accordance to the setting of the AM, I/D bits
as data is written to the internal GRAM. The address counter is not automatically updated when
read data from the internal GRAM.
AD[16:0]
17’h00000 ~ 17’h000EF
17’h00100 ~ 17’h001EF
17’h00200 ~ 17’h002EF
17’h00300 ~ 17’h003EF
GRAM Data Map
1st line GRAM Data
2nd line GRAM Data
3rd line GRAM Data
4th line GRAM Data
17’h13D00 ~ 17’ h13DEF
17’h13E00 ~ 17’ h13EEF
17’h13F00 ~ 17’h13FEF
318th line GRAM Data
319th line GRAM Data
320th line GRAM Data
Note1: When the RGB interface is selected (RM = “1”), the address AD[16:0] is set to the address counter
every frame on the falling edge of VSYNC.
Note2: When the internal clock operation or the VSYNC interface mode is selected (RM = “0”), the address
AD[16:0] is set to address counter when update register R21.
8.2.20. Write Data to GRAM (R22h)
R/W
RS
W
1
D17
D16
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
RAM write data (WD[17:0], the DB[17:0] pin assignment differs for each interface.
This register is the GRAM access port. When update the display data through this register, the address
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 67 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
counter (AC) is increased/decreased automatically.
8.2.21. Read Data from GRAM (R22h)
R/W
RS
R
1
D17
D16
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
RAM Read Data (RD[17:0], the DB[17:0] pin assignment differs for each interface.
RD[17:0] Read 18-bit data from GRAM through the read data register (RDR).
18-bit System Interface
GRAM Data &
RGB Mapping
R5
R4
R3
R2
R1
R0
G5
G4
G3
G2
G1
G0
B5
B4
B3
B2
B1
B0
Write Data
Register
RD
17
RD
16
RD
15
RD
14
RD
13
RD
12
RD
11
RD
10
RD
9
RD
8
RD
7
RD
6
RD
5
RD
4
RD
3
RD
2
RD
1
RD
0
Output Data
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
DB
11
DB
10
DB
9
DB
8
DB
7
DB
6
DB
5
DB
4
DB
3
DB
2
DB
1
DB
0
16-bit System Interface
GRAM Data &
RGB Mapping
R5
R4
R3
R2
R1
R0
G5
G4
G3
G2
G1
G0
B5
B4
B3
B2
B1
B0
Write Data
Register
RD
17
RD
16
RD
15
RD
14
RD
13
RD
12
RD
11
RD
10
RD
9
RD
8
RD
7
RD
6
RD
5
RD
4
RD
3
RD
2
RD
1
RD
0
Output Data
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
DB
11
DB
10
DB
8
DB
7
DB
6
DB
5
DB
4
DB
3
DB
2
DB
1
9-bit System Interface
GRAM Data &
RGB Mapping
R5
R4
R3
R2
R1
R0
G5
G4
G3
G2
G1
G0
B5
B4
B3
B2
B1
B0
Write Data
Register
RD
17
RD
16
RD
15
RD
14
RD
13
RD
12
RD
11
RD
10
RD
9
RD
8
RD
7
RD
6
RD
5
RD
4
RD
3
RD
2
RD
1
RD
0
Output Data
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
DB
11
DB
10
DB
9
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
DB
11
DB
10
DB
9
1st Transfer
2nd Transfer
8-bit System Interface / Serial Data Transfer Interface
GRAM Data &
RGB Mapping
R5
R4
R3
R2
R1
R0
G5
G4
G3
G2
G1
G0
B5
B4
B3
B2
B1
B0
Write Data
Register
RD
17
RD
16
RD
15
RD
14
RD
13
RD
12
RD
11
RD
10
RD
9
RD
8
RD
7
RD
6
RD
5
RD
4
RD
3
RD
2
RD
1
RD
0
Output Data
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
DB
11
DB
10
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
DB
11
DB
10
1st Transfer
2nd Transfer
Figure 28 Data Read from GRAM through Read Data Register in 18-/16-/9-/8-bit Interface Mode
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 68 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
Set I/D AM, HAS/HEA, VSA/VEA
Set address M
Dummy read (invalid data)
GRAM -> Read data latch
Read Output (data of address M)
Read datalatch -> DB[17:0]
Read Output (data of address M+1)
Read datalatch -> DB[17:0]
Set address N
Dummy read (invalid data)
GRAM -> Read data latch
Read Output (data of address N)
Read datalatch -> DB[17:0]
Figure 29 GRAM Data Read Back Flow Chart
8.2.22. Power Control 7 (R29h)
R/W
RS
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
W
1
0
0
0
0
0
0
0
0
0
0
D5
D4
D3
D2
D1
D0
VCM5 VCM4 VCM3 VCM2 VCM1 VCM0
VCM[5:0] Set the internal VcomH voltage.
VCM5 VCM4 VCM3 VCM2 VCM1 VCM0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
1
0
0
0
0
0
1
1
0
0
0
1
0
0
VCOMH
VREG1OUT
0.685
VREG1OUT
0.690
VREG1OUT
0.695
VREG1OUT
0.700
VREG1OUT
VCM5 VCM4 VCM3 VCM2 VCM1 VCM0
x
x
x
x
x
1
0
0
0
0
0
1
0
0
0
0
1
1
0
0
0
1
0
1
0
0
0
1
1
1
0
0
1
0
0
VCOMH
VREG1OUT
0.845
VREG1OUT
0.850
VREG1OUT
0.855
VREG1OUT
0.860
VREG1OUT
x
x
x
x
x
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 69 of 111
Version: 0.28
0
0
0
1
0
1
0
0
0
1
1
0
0
0
0
1
1
1
0
0
1
0
0
0
0
0
1
0
0
1
0
0
1
0
1
0
0
0
1
0
1
1
0
0
1
1
0
0
0
0
1
1
0
1
0
0
1
1
1
0
0
0
1
1
1
1
0
1
0
0
0
0
0
1
0
0
0
1
0
1
0
0
1
0
0
1
0
0
1
1
0
1
0
1
0
0
0
1
0
1
0
1
0
1
0
1
1
0
0
1
0
1
1
1
0
1
1
0
0
0
0
1
1
0
0
1
0
1
1
0
1
0
0
1
1
0
1
1
0
1
1
1
0
0
0
1
1
1
0
1
0
1
1
1
1
0
0
1
1
1
1
1
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
0.705
VREG1OUT
0.710
VREG1OUT
0.715
VREG1OUT
0.720
VREG1OUT
0.725
VREG1OUT
0.730
VREG1OUT
0.735
VREG1OUT
0.740
VREG1OUT
0.745
VREG1OUT
0.750
VREG1OUT
0.755
VREG1OUT
0.760
VREG1OUT
0.765
VREG1OUT
0.770
VREG1OUT
0.775
VREG1OUT
0.780
VREG1OUT
0.785
VREG1OUT
0.790
VREG1OUT
0.795
VREG1OUT
0.800
VREG1OUT
0.805
VREG1OUT
0.810
VREG1OUT
0.815
VREG1OUT
0.820
VREG1OUT
0.825
VREG1OUT
0.830
VREG1OUT
0.835
VREG1OUT
0.840
0.865
VREG1OUT
0.870
VREG1OUT
0.875
VREG1OUT
0.880
VREG1OUT
0.885
VREG1OUT
0.890
VREG1OUT
0.895
VREG1OUT
0.900
VREG1OUT
0.905
VREG1OUT
0.910
VREG1OUT
0.915
VREG1OUT
0.920
VREG1OUT
0.925
VREG1OUT
0.930
VREG1OUT
0.935
VREG1OUT
0.940
VREG1OUT
0.945
VREG1OUT
0.950
VREG1OUT
0.955
VREG1OUT
0.960
VREG1OUT
0.965
VREG1OUT
0.970
VREG1OUT
0.975
VREG1OUT
0.980
VREG1OUT
0.985
VREG1OUT
0.990
VREG1OUT
0.995
VREG1OUT
1.000
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
1
0
0
1
0
1
1
0
0
1
1
0
1
0
0
1
1
1
1
0
1
0
0
0
1
0
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
1
1
0
1
1
0
0
1
0
1
1
0
1
1
0
1
1
1
0
1
0
1
1
1
1
1
1
0
0
0
0
1
1
0
0
0
1
1
1
0
0
1
0
1
1
0
0
1
1
1
1
0
1
0
0
1
1
0
1
0
1
1
1
0
1
1
0
1
1
0
1
1
1
1
1
1
0
0
0
1
1
1
0
0
1
1
1
1
0
1
0
1
1
1
0
1
1
1
1
1
1
0
0
1
1
1
1
0
1
1
1
1
1
1
0
1
1
1
1
1
1
D3
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
8.2.23. Frame Rate and Color Control (R2Bh)
R/W
RS
D15
D14
D13
W
1
0
0
0
D12 D11
0
0
D10
D9
D8
D7
D6
D5
D4
0
0
0
0
0
0
0
D2
D1
D0
FRS3 FRS2 FRS1 FRS0
FRS[4:0] Set the frame rate when the internal resistor is used for oscillator circuit.
FRS[3:0]
0000
Frame Rate
40
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 70 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
Others
ILI9325
43
45
48
51
55
59
64
70
77
85
96 (default)
110
128
Setting Prohibited
8.2.24. Gamma Control (R30h ~ R3Dh)
R/W
RS
D12
D11
D10
D9
D8
D3
D2
D1
D0
R30h
W
1
D15 D14 D13
0
0
0
0
0
KP1[2]
KP1[1]
KP1[0]
D7 D6 D5 D4
0
0
0
0
0
KP0[2]
KP0[1]
KP0[0]
R31h
W
1
0
0
0
0
0
KP3[2]
KP3[1]
KP3[0]
0
0
0
0
0
KP2[2]
KP2[1]
KP2[0]
R32h
W
1
0
0
0
0
0
KP5[2]
KP5[1]
KP5[0]
0
0
0
0
0
KP4[2]
KP4[1]
KP4[0]
R35h
W
1
0
0
0
0
0
RP1[2]
RP1[1]
RP1[0]
0
0
0
0
0
RP0[2]
RP0[1]
RP0[0]
R36h
W
1
0
0
0
VRP1[4] VRP1[3] VRP1[2] VRP1[1] VRP1[0] 0
0
0
0
R37h
W
1
0
0
0
0
0
KN1[2]
KN1[1]
KN1[0]
0
0
0
0
0
KN0[2]
KN0[1]
KN0[0]
R38h
W
1
0
0
0
0
0
KN3[2]
KN3[1]
KN3[0]
0
0
0
0
0
KN2[2]
KN2[1]
KN2[0]
R39h
W
1
0
0
0
0
0
KN5[2]
KN5[1]
KN5[0]
0
0
0
0
0
KN4[2]
KN4[1]
KN4[0]
R3Ch
W
1
0
0
0
0
0
RN1[2]
RN1[1]
RN1[0]
0
0
0
0
0
RN0[2]
RN0[1]
RN0[0]
R3Dh
W
1
0
0
0
VRN1[4] VRN1[3] VRN1[2] VRN1[1] VRN1[0] 0
0
0
0
VRP0[3] VRP0[2] VRP0[1] VRP0[0]
VRN0[3] VRN0[2] VRN0[1] VRN0[0]
KP5-0[2:0] : γfine adjustment register for positive polarity
RP1-0[2:0] : γgradient adjustment register for positive polarity
VRP1-0[4:0] : γamplitude adjustment register for positive polarity
KN5-0[2:0] : γfine adjustment register for negative polarity
RN1-0[2:0] : γgradient adjustment register for negative polarity
VRN1-0[4:0] : γamplitude adjustment register for negative polarity
For details “γ-Correction Function” section.
8.2.25. Horizontal and Vertical RAM Address Position (R50h, R51h, R52h, R53h)
R/W
RS
R50h
W
1
D15 D14 D13 D12 D11 D10 D9
0
0
0
0
0
0
0
D8
0
HSA7 HSA6 HSA5 HSA4 HSA3 HSA2 HSA1 HSA0
D7
D6
D5
D4
D3
D2
D1
D0
R51h
W
1
0
0
0
0
0
0
0
0
HEA7 HEA6 HEA5 HEA4 HEA3 HEA2 HEA1 HEA0
R52h
W
1
0
0
0
0
0
0
0 VSA8 VSA7 VSA6 VSA5 VSA4 VSA3 VSA2 VSA1 VSA0
R53h
W
1
0
0
0
0
0
0
0
VEA8 VEA7 VEA6 VEA5 VEA4 VEA3 VEA2 VEA1 VEA0
HSA[7:0]/HEA[7:0] HSA[7:0] and HEA[7:0] represent the respective addresses at the start and end of the
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 71 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
window address area in horizontal direction. By setting HSA and HEA bits, it is possible to limit the
area on the GRAM horizontally for writing data. The HSA and HEA bits must be set before starting
RAM write operation. In setting these bits, be sure “00”h ≤ HSA[7:0]< HEA[7:0] ≤ “EF”h. and
“04”h≦HEA-HAS.
VSA[8:0]/VEA[8:0] VSA[8:0] and VEA[8:0] represent the respective addresses at the start and end of the
window address area in vertical direction. By setting VSA and VEA bits, it is possible to limit the
area on the GRAM vertically for writing data. The VSA and VEA bits must be set before starting
RAM write operation. In setting, be sure “000”h ≤ VSA[8:0]< VEA[8:0] ≤ “13F”h.
HSA
HEA
0000h
VSA
Window Address
Area
VEA
GRAM Address Area
13FEFh
Figure 30 GRAM Access Range Configuration
“00”h ≤HAS[7:0] ≤HEA[7:0] ≤”EF”h
“00”h ≤VSA[7:0] ≤VEA[7:0] ≤”13F”h
Note1. The window address range must be within the GRAM address space.
Note2. Data are written to GRAM in four-words when operating in high speed mode, the dummy write
operations should be inserted depending on the window address area. For details, see the High-Speed RAM
Write Function section.
8.2.26. Gate Scan Control (R60h, R61h, R6Ah)
R/W
RS
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
R60h
W
1
GS
0
NL5
NL4
NL3
NL2
NL1
NL0
0
0
D5
D4
D3
D2
D1
D0
R61h
W
1
0
0
0
0
0
0
0
0
0
0
0
0
0
NDL
VLE
REV
R6Ah
W
1
0
0
0
0
0
0
0
VL8
VL7
VL6
VL5
VL4
VL3
VL2
VL1
VL0
SCN5 SCN4 SCN3 SCN2 SCN1 SCN0
SCN[5:0] The ILI9325 allows to specify the gate line from which the gate driver starts to scan by setting the
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 72 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
SCN[5:0] bits.
Scanning Start Position
SCN[5:0]
00h
01h
02h
03h
04h
05h
06h
07h
08h
09h
0Ah
0Bh
0Ch
0Dh
0Eh
0Fh
10h
11h
12h
13h
14h
15h
16h
17h
18h
19h
1Ah
1Bh
1Ch
1Dh
1Eh
1Fh
20h
21h
22h
23h
24h
25h
26h
27h
28h ~ 3Fh
SM=0
GS=0
G1
G9
G17
G25
G33
G41
G49
G57
G65
G73
G81
G89
G97
G105
G113
G121
G129
G137
G145
G153
G161
G169
G177
G185
G193
G201
G209
G217
G225
G233
G241
G249
G257
G265
G273
G281
G289
G297
G305
G313
Setting disabled
SM=1
GS=1
G320
G312
G304
G296
G288
G280
G272
G264
G256
G248
G240
G232
G224
G216
G208
G200
G192
G184
G176
G168
G160
G152
G144
G136
G128
G120
G112
G104
G96
G88
G80
G72
G64
G56
G48
G40
G32
G24
G16
G8
Setting disabled
GS=0
G1
G17
G33
G49
G65
G81
G97
G113
G129
G145
G161
G177
G193
G209
G2
G18
G34
G50
G66
G82
G98
G114
G130
G146
G162
G178
G194
G114
G130
G146
G162
G178
G194
G210
G226
G242
G258
G274
G290
G306
Setting disabled
GS=1
G320
G304
G288
G272
G256
G240
G224
G208
G192
G176
G160
G144
G128
G112
G96
G80
G64
G48
G32
G16
G319
G303
G287
G271
G255
G239
G223
G207
G191
G175
G159
G143
G127
G111
G95
G79
G63
G47
G31
G15
Setting disabled
NL[5:0]: Sets the number of lines to drive the LCD at an interval of 8 lines. The GRAM address mapping is
not affected by the number of lines set by NL[5:0]. The number of lines must be the same or more
than the number of lines necessary for the size of the liquid crystal panel.
NL[5:0]
LCD Drive Line
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 73 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
6’h1D
6’h1E
6’h1F
6’h20
6’h21
6’h22
6’h23
6’h24
6’h25
6’h26
6’h27
Others
ILI9325
240 lines
248 lines
256 lines
264 lines
272 lines
280 lines
288 lines
296 lines
304 lines
312 line
320 line
Setting inhibited
NDL: Sets the source driver output level in the non-display area.
Non-Display Area
Positive Polarity
Negative Polarity
V63
V0
V0
V63
NDL
0
1
GS: Sets the direction of scan by the gate driver in the range determined by SCN[4:0] and NL[4:0]. The scan
direction determined by GS = 0 can be reversed by setting GS = 1.
When GS = 0, the scan direction is from G1 to G320.
When GS = 1, the scan direction is from G320 to G1
REV: Enables the grayscale inversion of the image by setting REV=1.
REV
0
1
GRAM Data
18’h00000
.
.
.
18’h3FFFF
18’h00000
.
.
.
18’h3FFFF
Source Output in Display Area
Positive polarity negative polarity
V63
V0
.
.
.
.
.
.
V0
V63
V0
V63
.
.
.
.
.
.
V63
V0
VLE: Vertical scroll display enable bit. When VLE = 1, the ILI9325 starts displaying the base image from the
line (of the physical display) determined by VL[8:0] bits. VL[8:0] sets the amount of scrolling, which is the
number of lines to shift the start line of the display from the first line of the physical display. Note that the
partial image display position is not affected by the base image scrolling.
The vertical scrolling is not available in external display interface operation. In this case, make sure to
set VLE = “0”.
VLE
0
Base Image Display
Fixed
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 74 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
1
ILI9325
Enable Scrolling
VL[8:0]: Sets the scrolling amount of base image. The base image is scrolled in vertical direction and
displayed from the line determined by VL[8:0]. Make sure that VL[8:0] ≦320.
8.2.27. Partial Image 1 Display Position (R80h)
R/W
W
RS
D15
1
0
D14
D13
0
0
D12
0
D11
0
D10
0
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
PTD
PTD
PTD
PTD
PTD
PTD
PTD
PTD
PTD
P0[8]
P0[7]
P0[6]
P0[5]
P0[4]
P0[3]
P0[2]
P0[1]
P0[0]
0
PTDP0[8:0]: Sets the display position of partial image 1. The display areas of the partial images 1 and 2 must
not overlap each another.
8.2.28. Partial Image 1 RAM Start/End Address (R81h, R82h)
R/W
RS
D15
D14
D13
D12
D11
D10
D9
W
1
0
0
0
0
0
0
0
W
1
0
0
0
0
0
0
0
D8
D7
D6
D5
D4
D3
D2
D1
D0
PTS
PTS
PTS
PTS
PTS
PTS
PTS
PTS
PTS
A0[8]
A0[7]
A0[6]
A0[5]
A0[4]
A0[3]
A0[2]
A0[1]
A0[0]
PTE
PTE
PTE
PTE
PTE
PTE
PTE
PTE
PTE
A0[8]
A0[7]
A0[6]
A0[5]
A0[4]
A0[3]
A0[2]
A0[1]
A0[0]
PTSA0[8:0] PTEA0[8:0]: Sets the start line address and the end line address of the RAM area storing the
data of partial image 1. Make sure PTSA0[8:0] ≤ PTEA0[8:0].
8.2.29. Partial Image 2 Display Position (R83h)
R/W
RS
D15
D14
D13
D12
D11
D10
D9
W
1
0
0
0
0
0
0
0
D8
D7
D6
D5
D4
D3
D2
D1
D0
PTS PTD
PTD
PTD
PTD
PTD
PTD
PTD
PTD
A1[8] P1[7]
P1[6]
P1[5]
P1[4]
P1[3]
P1[2]
P1[1]
P1[0]
PTDP1[8:0]: Sets the display position of partial image 2 The display areas of the partial images 1 and 2 must
not overlap each another.
8.2.30. Partial Image 2 RAM Start/End Address (R84h, R85h)
R/W
W
W
RS
D15
1
0
1
0
D14
0
0
D13
0
0
D12
0
0
D11
0
0
D10
0
0
D9
D7
D6
D5
D4
D3
D2
D1
D0
PTS PTS
D8
PTS
PTS
PTS
PTS
PTS
PTS
PTS
A1[8] A1[7]
A1[6]
A1[5]
A1[4]
A1[3]
A1[2]
A1[1]
A1[0]
PTE PTE
PTE
PTE
PTE
PTE
PTE
PTE
PTE
A1[8] A1[7]
A1[6]
A1[5]
A1[4]
A1[3]
A1[2]
A1[1]
A1[0]
0
0
PTSA1[8:0] PTEA1[8:0]: Sets the start line address and the end line address of the RAM area storing the
data of partial image 2 Make sure PTSA1[8:0] ≤ PTEA1[8:0].
8.2.31. Panel Interface Control 1 (R90h)
R/W
RS
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 75 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
W
1
0
0
0
0
0
0
DIVI1
DIVI0
0
0
0
RTNI4
ILI9325
RTNI3
RTNI2
RTNI1
RTNI0
RTNI[4:0]: Sets 1H (line) clock number of internal clock operating mode. In this mode, ILI9325 display
operation is synchronized with internal clock signal.
RTNI[4:0]
00000~01111
10000
10001
10010
10011
10100
10101
10110
10111
Clocks/Line
Setting Disabled
16 clocks
17 clocks
18 clocks
19 clocks
20 clocks
21 clocks
22 clocks
23 clocks
RTNI[4:0]
11000
11001
11010
11011
11100
11101
11110
11111
Clocks/Line
24 clocks
25 clocks
26 clocks
27 clocks
28 clocks
29 clocks
30 clocks
31 clocks
DIVI[1:0]: Sets the division ratio of internal clock frequency.
DIVI1
0
DIVI0
0
Division Ratio
1
Internal Operation Clock Frequency
fosc / 1
0
1
2
fosc / 2
1
0
4
fosc / 4
1
1
8
fosc / 8
8.2.32. Panel Interface Control 2 (R92h)
R/W
RS
D15
D14
D13
D12
D11
W
1
0
0
0
0
0
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
0
0
0
0
0
0
0
0
NOWI[2] NOWI[1] NOWI[0]
NOWI[2:0]: Sets the gate output non-overlap period when ILI9325 display operation is synchronized with
internal clock signal.
NOWI[2:0]
000
001
010
011
100
101
110
111
Gate Non-overlap Period
0 clocks
1 clocks
2 clocks
3 clocks
4 clocks
5 clocks
6 clocks
7 clocks
Note: The gate output non-overlap period is defined by the number of frequency-divided internal clocks, the
frequency of which is determined by instruction (DIVI), from the reference point.
8.2.33. Panel Interface Control 4 (R95h)
R/W
RS
D15
D14
D13
D12
D11
D10
W
1
0
0
0
0
0
0
D9
D8
DIVE1 DIVE0
D7
D6
0
0
D5
D4
D3
D2
D1
D0
RTNE5 RTNE4 RTNE3 RTNE2 RTNE1 RTNE0
RTNE[5:0]: Sets 1H (line) clock number of RGB interface mode. In this mode, ILI9325 display operation is
synchronized with RGB interface signals.
DIVE (division ratio) x RTNE (DOTCLKs) ≤ DOTCLKs in 1H period.
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 76 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
RTNE[5:0]
00h
01h
02h
03h
04h
05h
06h
07h
08h
09h
0ah
0bh
0ch
0dh
0eh
0fh
Clocks per line period
RTNE[5:0]
(1H)
Setting Prohibited
Setting Prohibited
Setting Prohibited
Setting Prohibited
Setting Prohibited
Setting Prohibited
Setting Prohibited
Setting Prohibited
Setting Prohibited
Setting Prohibited
Setting Prohibited
Setting Prohibited
Setting Prohibited
Setting Prohibited
Setting Prohibited
Setting Prohibited
Clocks per line period
10h
11h
12h
13h
14h
15h
16h
17h
18h
19h
1ah
1bh
1ch
1dh
1eh
1fh
Clocks per line period
RTNE[5:0]
(1H)
16 clocks
17 clocks
18 clocks
19 clocks
20 clocks
21 clocks
22 clocks
23 clocks
24 clocks
25 clocks
26 clocks
27 clocks
28 clocks
29 clocks
30 clocks
31 clocks
ILI9325
RTNE[5:0]
(1H)
20h
21h
22h
23h
24h
25h
26h
27h
28h
29h
2ah
2bh
2ch
2dh
2eh
2fh
32 clocks
33 clocks
34 clocks
35 clocks
36 clocks
37 clocks
38 clocks
39 clocks
40 clocks
41 clocks
42 clocks
43 clocks
44 clocks
45 clocks
46 clocks
47 clocks
Clocks per line period
(1H)
30h
31h
32h
33h
34h
35h
36h
37h
38h
39h
3ah
3bh
3ch
3dh
3eh
3fh
48 clocks
49 clocks
50 clocks
51 clocks
52 clocks
53 clocks
54 clocks
55 clocks
56 clocks
57 clocks
58 clocks
59 clocks
60 clocks
61 clocks
62 clocks
63 clocks
DIVE[1:0]: Sets the division ratio of DOTCLK when ILI9325 display operation is synchronized with RGB
interface signals.
DIVE[1:0]
Division Ratio
18/16-bit RGB Interface
DOTCLK=5MHz
6-bit x 3 Transfers RGB Interface
DOTCLK=5MHz
00
Setting Prohibited
Setting Prohibited
-
Setting Prohibited
01
1/4
4
DOTCLKS
0.8 μs
12
DOTCLKS
0.8 μs
10
1/8
8
DOTCLKS
1.6 μs
24
DOTCLKS
1.6 μs
DOTCLKS
3.2 μs
48
DOTCLKS
3.2 μs
11
1/16
16
8.2.34. OTP VCM Programming Control (RA1h)
R/W
RS
D15
D14
D13
D12
W
1
0
0
0
0
D11
OTP_
PGM_EN
D10
D9
D8
D7
D6
0
0
0
0
0
D5
VCM_
OTP5
D4
VCM_
OTP4
D3
VCM_
OTP3
D2
VCM_
OTP2
D1
VCM_
OTP1
D0
VCM_
OTP0
OTP_PGM_EN: OTP programming enable. When program OTP, must set this bit. OTP data can be
programmed 3 times.
VCM_OTP[5:0]: OTP programming data for VCOMH voltage, the voltage refer to VCM[5:0] value.
8.2.35. OTP VCM Status and Enable (RA2h)
R/W
RS
W
1
D15
PGM_
CNT1
D14
PGM_
CNT0
D13
VCM_
D5
D12
VCM_
D4
D11
VCM_
D3
D10
VCM_
D2
D9
VCM_
D1
D8
VCM_
D0
D7
D6
D5
D4
D3
D2
D1
0
0
0
0
0
0
0
D0
VCM_
EN
PGM_CNT[1:0]: OTP programmed record. These bits are read only.
OTP_PGM_CNT[1:0]
Description
00
OTP clean
01
OTP programmed 1 time
10
OTP programmed 2 times
11
OTP programmed 3 times
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 77 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
VCM_D[5:0]: OTP VCM data read value. These bits are read only.
VCM_EN: OTP VCM data enable.
’1’: Set this bit to enable OTP VCM data to replace R29h VCM value.
’0’: Default value, use R29h VCM value.
8.2.36. OTP Programming ID Key (RA5h)
R/W
RS
W
1
D15
KEY
15
D14
KEY
14
D13
KEY
13
D12
KEY
12
D11
KEY
11
D10
KEY
10
D9
KEY
9
D8
KEY
8
D7
KEY
7
D6
KEY
6
D5
KEY
5
D4
KEY
4
D3
KEY
3
D2
KEY
2
D1
KEY
1
D0
KEY
0
KEY[15:0]: OTP Programming ID key protection. Before writing OTP programming data RA1h, it must write
RA5h with 0xAA55 value first to make OTP programming successfully. If RA5h is not written with
0xAA55, OTP programming will be fail. See OTP Programming flow.
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 78 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
9. OTP Programming Flow
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 79 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
Start
Power On ILI9325
Check
OTP_PGM_CNT=11?
Y
N
Supply External
7.0V to DDVDH
Wait 10ms
Set ID Key
RA5h=0xAA55
Program OTP VCM Data
RA1h=0x08xx
(xx=6 bit VCM value)
Wait 10ms
Cut Off External
7.0V Power
Reset
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
End
Page 80 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 81 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
10. GRAM Address Map & Read/Write
ILI9325 has an internal graphics RAM (GRAM) of 87,120 bytes to store the display data and one pixel is
constructed of 18 bits. The GRAM can be accessed through the i80 system, SPI and RGB interfaces.
i80 18-/16-bit System Bus Interface Timing
(a) Write to GRAM
nCS
RS
nRD
nWR
DB[17:0]
Write “0022h” to
index register
Write GRAM “data”
Nth pixel
Write GRAM “data”
(N+1)th pixel
Dummy
Read
1st Read “data”
Nth pixel
Write GRAM “data”
(N+2)th pixel
Write GRAM “data”
(N+3)th pixel
(b) Read from GRAM
nCS
RS
nRD
nWR
DB[17:0]
Write “0022h” to
index register
2nd Read “data”
(N+1)th pixel
3rd Read “data”
(N+2)th pixel
i80 9-/8-bit System Bus Interface Timing
(a) Write to GRAM
nCS
RS
nRD
nWR
DB[17:9]
“00h”
“22h”
1st write
high byte
1st write
low byte
Nth pixel
2nd write
high byte
2nd write
low byte
(N+1)th pixel
3rd write
high byte
3rd write
low byte
(N+2)th pixel
(b) Read from GRAM
nCS
RS
nRD
nWR
DB[17:9]
“00h”
“22h”
Dummy
Read 1
Dummy
Read 2
1st read
high byte
1st read
low byte
Nth pixel
2nd read
high byte
2nd read
low byte
(N+1)th pixel
Figure31 GRAM Read/Write Timing of i80-System Interface
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 82 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
GRAM address map table of SS=0, BGR=0
S1…S3
S4…S6
S7…S9
S10…S12
…
S517…S519
S520…S522
S523…S525
GS=0
SS=0, BGR=0
GS=1
DB17…0
DB17…0
DB17…0
DB17…0
…
DB17…0
DB17…0
DB17…0
S526…S720
DB17…0
G1
G320
“00000h”
“00001h”
“00002h”
“00003h”
…
“000ECh”
“000EDh”
“000EEh”
“000EFh”
G2
G319
“00100h”
“00101h”
“00102h”
“00103h”
…
“001ECh”
“001EDh”
“001EEh”
“001EFh”
G3
G318
“00200h”
“00201h”
“00202h”
“00203h”
…
“002ECh”
“002EDh”
“002EEh”
“002EFh”
G4
G317
“00300h”
“00301h”
“00302h”
“00303h”
…
“003ECh”
“003EDh”
“003EEh”
“003EFh”
G5
G316
“00400h”
“00401h”
“00402h”
“00403h”
…
“004ECh”
“004EDh”
“004EEh”
“004EFh”
G6
G315
“00500h”
“00501h”
“00502h”
“00503h”
…
“005ECh”
“005EDh”
“005EEh”
“005EFh”
G7
G314
“00600h”
“00601h”
“00602h”
“00603h”
…
“006ECh”
“006EDh”
“006EEh”
“006EFh”
G8
G313
“00700h”
“00701h”
“00702h”
“00703h”
…
“007ECh”
“007EDh”
“007EEh”
“007EFh”
G9
G312
“00800h”
“00801h”
“00802h”
“00803h”
…
“008ECh”
“008EDh”
“008EEh”
“008EFh”
G10
G311
“00900h”
“00901h”
“00902h”
“00903h”
…
“009ECh”
“009EDh”
“009EEh”
“009EFh”
.
.
.
.
.
.
…
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
G311
G10
“13600h”
“13601h”
“13602h”
“13603h”
…
“136ECh”
“136EDh”
“136EEh”
“136EFh”
G312
G9
“13700h”
“13701h”
“13702h”
“13703h”
…
“137ECh”
“137EDh”
“137EEh”
“137EFh”
G313
G8
“13800h”
“13801h”
“13802h”
“13803h”
…
“138ECh”
“138EDh”
“138EEh”
“138EFh”
G314
G7
“13900h”
“13901h”
“13902h”
“13903h”
…
“139ECh”
“139EDh”
“139EEh”
“139EFh”
G315
G6
“13A00h”
“13A01h”
“13A02h”
“13A03h”
…
“13AECh”
“13AEDh”
“13AEEh”
“13AEFh”
G316
G5
“13B00h”
“13B01h”
“13B02h”
“13B03h”
…
“13BECh”
“13BEDh”
“13BEEh”
“13BEFh”
G317
G4
“13C00h”
“13C01h”
“13C02h”
“13C03h”
…
“13CECh”
“13CEDh”
“13CEEh”
“13CEFh”
G318
G3
“13D00h”
“13D01h”
“13D02h”
“13D03h”
…
“13DECh”
“13DEDh”
“13DEEh”
“13DEFh”
G319
G2
“13E00h”
“13E01h”
“13E02h”
“13E03h”
…
“13EECh”
“13EEDh”
“13EEEh”
“13EEFh”
G320
G1
“13F00h”
“13F01h”
“13F02h”
“13F03h”
…
“13FECh”
“13FEDh”
“13FEEh”
“13FEFh”
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 83 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
i80/M68 system 18-bit data bus interface
GRAM Data
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
DB
11
DB
10
DB
9
DB
8
DB
7
DB
6
DB
5
DB
4
DB
3
DB
2
DB
1
DB
0
RGB Assignment
R5
R4
R3
R2
R1
R0
G5
G4
G3
G2
G1
G0
B5
B4
B3
B2
B1
B0
Source Output Pin
S (3n+1)
S (3n+2)
S (3n+3)
N=0 to 175
i80/M68 system 16-bit data bus interface
GRAM Data
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
DB
11
DB
10
RGB Assignment
R5
R4
R3
R2
R1
R0
G5
G4
Source Output Pin
S (3n+1)
G3
DB
8
DB
7
DB
6
DB
5
DB
4
DB
3
DB
2
DB
1
G2
G1
G0
B5
B4
B3
B2
B1
S (3n+2)
B0
S (3n+3)
N=0 to 175
i80/M68 system 9-bit data bus interface
1st Transfer
2nd Transfer
GRAM Data
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
DB
11
DB
10
DB
9
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
DB
11
DB
10
DB
9
RGB Assignment
R5
R4
R3
R2
R1
R0
G5
G4
G3
G2
G1
G0
B5
B4
B3
B2
B1
B0
Source Output Pin
S (3n+1)
S (3n+2)
S (3n+3)
N=0 to 175
GRAM Data and display data of 18-/16-/9-bit system interface (SS=”0", BGR=”0")
Figure32 i80-System Interface with 18-/16-/9-bit Data Bus (SS=”0”, BGR=”0”)
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 84 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
i80/M68 system 8-bit interface / SPI Interface (2 transfers/pixel)
1st transfer
2nd transfer
GRAM Data
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
DB
11
DB
10
RGB Assignment
R5
R4
R3
R2
R1
R0
G5
G4
Source Output Pin
S (3n+1)
G3
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
DB
11
DB
10
G2
G1
G0
B5
B4
B3
B2
B1
S (3n+2)
B0
S (3n+3)
N=0 to 175
i80/M68 system 8-bit interface (3 transfers/pixel, TRI=”1", DFM[1:0]=”00")
2nd Transfer
1st Transfer
3rd Transfer
GRAM Data
DB
11
DB
10
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
DB
11
DB
10
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
DB
11
DB
10
RGB Assignment
R5
R4
R3
R2
R1
R0
G5
G4
G3
G2
G1
G0
B5
B4
B3
B2
B1
B0
Source Output Pin
S (3n+1)
S (3n+2)
S (3n+3)
N=0 to 175
i80/M68 system 8-bit interface (3 transfers/pixel, TRI=”1", DFM[1:0]=”10)
1st Transfer
2nd Transfer
3rd Transfer
GRAM Data
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
RGB Assignment
R5
R4
R3
R2
R1
R0
G5
G4
G3
G2
G1
G0
B5
B4
B3
B2
B1
B0
Source Output Pin
S (3n+1)
S (3n+2)
S (3n+3)
N=0 to 175
i80/M68 system 8-bit interface (SS=”0", BGR=”0")
Figure33 i80-System Interface with 8-bit Data Bus (SS=”0”, BGR=”0”)
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 85 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
GRAM address map table of SS=1, BGR=1
SS=0, BGR=0
S720…S718
S717…S715
S714…S712
S711…S709
…
S12…S10
S9…S7
S6…S4
S3…S1
GS=0
GS=1
DB17…0
DB17…0
DB17…0
DB17…0
…
DB17…0
DB17…0
DB17…0
DB17…0
G1
G320
“00000h”
“00001h”
“00002h”
“00003h”
…
“000ECh”
“000EDh”
“000EEh”
“000EFh”
G2
G319
“00100h”
“00101h”
“00102h”
“00103h”
…
“001ECh”
“001EDh”
“001EEh”
“001EFh”
G3
G318
“00200h”
“00201h”
“00202h”
“00203h”
…
“002ECh”
“002EDh”
“002EEh”
“002EFh”
G4
G317
“00300h”
“00301h”
“00302h”
“00303h”
…
“003ECh”
“003EDh”
“003EEh”
“003EFh”
G5
G316
“00400h”
“00401h”
“00402h”
“00403h”
…
“004ECh”
“004EDh”
“004EEh”
“004EFh”
G6
G315
“00500h”
“00501h”
“00502h”
“00503h”
…
“005ECh”
“005EDh”
“005EEh”
“005EFh”
G7
G314
“00600h”
“00601h”
“00602h”
“00603h”
…
“006ECh”
“006EDh”
“006EEh”
“006EFh”
G8
G313
“00700h”
“00701h”
“00702h”
“00703h”
…
“007ECh”
“007EDh”
“007EEh”
“007EFh”
G9
G312
“00800h”
“00801h”
“00802h”
“00803h”
…
“008ECh”
“008EDh”
“008EEh”
“008EFh”
G10
G311
“00900h”
“00901h”
“00902h”
“00903h”
…
“009ECh”
“009EDh”
“009EEh”
“009EFh”
.
.
.
.
.
.
…
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
G311
G10
“13600h”
“13601h”
“13602h”
“13603h”
…
“136ECh”
“136EDh”
“136EEh”
“136EFh”
G312
G9
“13700h”
“13701h”
“13702h”
“13703h”
…
“137ECh”
“137EDh”
“137EEh”
“137EFh”
G313
G8
“13800h”
“13801h”
“13802h”
“13803h”
…
“138ECh”
“138EDh”
“138EEh”
“138EFh”
G314
G7
“13900h”
“13901h”
“13902h”
“13903h”
…
“139ECh”
“139EDh”
“139EEh”
“139EFh”
G315
G6
“13A00h”
“13A01h”
“13A02h”
“13A03h”
…
“13AECh”
“13AEDh”
“13AEEh”
“13AEFh”
G316
G5
“13B00h”
“13B01h”
“13B02h”
“13B03h”
…
“13BECh”
“13BEDh”
“13BEEh”
“13BEFh”
G317
G4
“13C00h”
“13C01h”
“13C02h”
“13C03h”
…
“13CECh”
“13CEDh”
“13CEEh”
“13CEFh”
G318
G3
“13D00h”
“13D01h”
“13D02h”
“13D03h”
…
“13DECh”
“13DEDh”
“13DEEh”
“13DEFh”
G319
G2
“13E00h”
“13E01h”
“13E02h”
“13E03h”
…
“13EECh”
“13EEDh”
“13EEEh”
“13EEFh”
G320
G1
“13F00h”
“13F01h”
“13F02h”
“13F03h”
…
“13FECh”
“13FEDh”
“13FEEh”
“13FEFh”
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 86 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
i80/M68 system 18-bit data bus interface
GRAM Data
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
DB
11
DB
10
DB
9
DB
8
DB
7
DB
6
DB
5
DB
4
DB
3
DB
2
DB
1
DB
0
RGB Assignment
R5
R4
R3
R2
R1
R0
G5
G4
G3
G2
G1
G0
B5
B4
B3
B2
B1
B0
Source Output Pin
S (528-3n)
S (527-3n)
S (526-3n)
N=0 to 175
i80/M68 system 9-bit data bus interface
1st Transfer
2nd Transfer
GRAM Data
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
DB
11
DB
10
DB
9
DB
17
DB
16
DB
15
DB
14
DB
13
DB
12
DB
11
DB
10
DB
9
RGB Assignment
R5
R4
R3
R2
R1
R0
G5
G4
G3
G2
G1
G0
B5
B4
B3
B2
B1
B0
Source Output Pin
S (528-3n)
S (527-3n)
S (526-3n)
N=0 to 175
GRAM Data and display data of 18-/9-bit system interface (SS=”1", BGR=”1")
Figure 34 i80-System Interface with 18-/9-bit Data Bus (SS=”1”, BGR=”1”)
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 87 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
11. Window Address Function
The window address function enables writing display data consecutively in a rectangular area (a window
address area) made on the internal RAM. The window address area is made by setting the horizontal address
register (start: HSA[7:0], end: HEA[7:0] bits) and the vertical address register (start: VSA[8:0], end: VEA[8:0]
bits). The AM bit sets the transition direction of RAM address (either increment or decrement). These bits
enable the ILI9325 to write data including image data consecutively not taking data wrap positions into
account.
The window address area must be made within the GRAM address map area. Also, the GRAM address bits
(RAM address set register) must be an address within the window address area.
[Window address setting area]
(Horizontal direction) 00H ≤ HSA[7:0] ≤ HEA[7:0] ≤ “EF”H
(Vertical direction) 00H ≤ VSA[8:0] ≤ VEA[8:0]≤ “13F”H
[RAM address, AD (an address within a window address area)]]
(RAM address) HSA[7:0] ≤ AD[7:0] ≤ HEA[7:0]
VSA[8:0] ≤ AD[15:8] ≤ VEA[8:0]
GRAM Address Map
“00000”h
“000EF”h
Window Address Area
2010h
203Fh
2110h
213Fh
4F10h
4F3Fh
“13F00”h
“13FEF”h
Window address setting area
HSA[7:0] = 10h, HSA[7:0] = 3Fh,
VSA[8:0] = 20h, VSA[8:0] = 4Fh,
I/D = 1 (increment)
AM = 0 (horizontal writing)
Figure 35 GRAM Access Window Map
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 88 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 89 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
12. Gamma Correction
ILI9325 incorporates the γ-correction function to display 262,144 colors for the LCD panel. The γ-correction is
performed with 3 groups of registers determining eight reference grayscale levels, which are gradient
adjustment, amplitude adjustment and fine-adjustment registers for positive and negative polarities, to make
ILI9325 available with liquid crystal panels of various characteristics.
Gradient
Adjustment
Register
VREG1OUT
PRP/N0
PRP/N1
Fine Adjustment Registers (6 x 3 bits)
PKP/N5 PKP/N4 PKP/N3
PKP/N2
PKP/N1
PKP/N0
Amplitude
Adjustment
Register
VRP/N0
VRP/N1
V0
VgP1/VgN1
V1
V2
V7
VgP8/VgN8
VgP43/VgN43
VgP55/VgN55
…...
V20
…...
VgP20/VgN20
V8
V43
…...
8 to 1
selection
8 to 1
selection
8 to 1
selection
8 to 1
selection
…...
8 to 1
selection
VgP0/VgN0
V55
8 to 1
selection
…...
V56
VgP62/VgN62
VgP63/VgN63
V61
V62
V63
VGS
Figure 36 Grayscale Voltage Generation
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 90 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
VREG1OUT
1R
1R
RP16
RP17
RP18
RP19
RP20
RP21
RP22
RP23
RP24
RP25
RP26
RP27
RP28
RP29
RP30
RP31
RP32
RP33
RP34
RP35
RP36
RP37
RP38
VRCP1
0 ~ 28R
{
4R
5R
8R
VP25
VP26
VP27
VP28
VP29
VP30
VP31
VP32
VP33
VP34
VP35
VP36
VP37
VP38
VP39
VP40
RP39
RP40
RP41
RP42
RP43
RP44
RP45
RP46
VP41
VP42
VP43
VP44
VP45
VP46
VP47
VP48
VP49
VgP20
PKP3[2:0]
VgP43
PKP4[2:0]
VgP55
PKP5[2:0]
VgP62
VgP63
{
RN1
RN2
RN3
RN4
RN5
RN6
RN7
4R
VRCP0
0 ~ 28R
{
{
{
{
1R
1R
1R
1R
RN8
RN9
RN10
RN11
RN12
RN13
RN14
RN15
RN16
RN17
RN18
RN19
RN20
RN21
RN22
RN23
RN24
RN25
RN26
RN27
RN28
RN29
RN30
RN31
RN32
RN33
RN34
RN35
RN36
RN37
RN38
{
5R
RP47
8R
VN17
VN18
VN19
VN20
VN21
VN22
VN23
VN24
VN25
VN26
VN27
VN28
VN29
VN30
VN31
VN32
VN33
VN34
VN35
VN36
VN37
VN38
VN39
VN40
RN39
RN40
RN41
RN42
RN43
RN44
RN45
RN46
VN41
VN42
VN43
VN44
VN45
VN46
VN47
VN48
VgN1
PKN1[2:0]
VgN8
PKN2[2:0]
VgN20
PKN3[2:0]
VgN43
PKN4[2:0]
PRN1[2:0]
VRON1
0 ~ 31R
VRP1[4:0]
VN9
VN10
VN11
VN12
VN13
VN14
VN15
VN16
VgN0
PKN0[2:0]
PRN0[2:0]
VRCN1
0 ~ 28R
4R
VN1
VN2
VN3
VN4
VN5
VN6
VN7
VN8
8 to 1
Selection
RN0
8 to 1
Selection
8 to 1
Selection
VgP8
PKP2[2:0]
PRP1[2:0]
VROP1
0 ~ 31R
VGS
VP17
VP18
VP19
VP20
VP21
VP22
VP23
VP24
8 to 1
Selection
RP15
8 to 1
Selection
1R
RP8
RP9
RP10
RP11
RP12
RP13
RP14
VP9
VP10
VP11
VP12
VP13
VP14
VP15
VP16
PKP1[2:0]
8 to 1
Selection
{
{
{
{
1R
PRP0[2:0]
VgP1
5R
8 to 1
Selection
VRCP0
0 ~ 28R
PKP0[2:0]
VRN0[4:0]
8 to 1
Selection
{
4R
VP1
VP2
VP3
VP4
VP5
VP6
VP7
VP8
VRON0
0 ~ 30R
8 to 1
Selection
RP0
RP1
RP2
RP3
RP4
RP5
RP6
RP7
8 to 1
Selection
5R
8 to 1
Selection
1uF/10V
VgP0
VRP0[4:0]
8 to 1
Selection
VROP0
0 ~ 30R
VN49
VgN55
PKN5[2:0]
VgN62
VgN63
VRN1[4:0]
RN47
Figure 37 Grayscale Voltage Adjustment
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 91 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
1. Gradient adjustment registers
The gradient adjustment registers are used to adjust the gradient of the curve representing the relationship
between the grayscale and the grayscale reference voltage level. To adjust the gradient, the resistance
values of variable resistors in the middle of the ladder resistor are adjusted by registers PRP0[2:0]/PRN0[2:0],
PRP1[2:0]/PRN1[2:0]. The registers consist of positive and negative polarity registers, allowing asymmetric
drive.
2. Amplitude adjustment registers
The amplitude adjustment registers, VRP0[3:0]/VRN0[3:0], VRP1[4:0]/VRN1[4:0], are used to adjust the
amplitude of grayscale voltages. To adjust the amplitude, the resistance values of variable resistors at the top
and bottom of the ladder resistor are adjusted. Same as the gradient registers, the amplitude adjustment
registers consist of positive and negative polarity registers.
3. Fine adjustment registers
The fine adjustment registers are used to fine-adjust grayscale voltage levels. To fine-adjust grayscale
voltage levels, fine adjustment registers adjust the reference voltage levels, 8 levels for each register
generated from the ladder resistor, in respective 8-to-1 selectors. Same with other registers, the fine
Gradient adjustment
Grayscale voltage
Grayscale voltage
Grayscale voltage
adjustment registers consist of positive and negative polarity registers.
Amplitude adjustment
Fine adjustment
Figure 38 Gamma Curve Adjustment
Register Groups
Gradient
adjustment
Amplitude
adjustment
Fine adjustment
Positive Polarity
PRP0 [2:0]
PRP1 [2:0]
VRP0 [3:0]
VRP1 [4:0]
KP0 [2:0]
KP1 [2:0]
KP2 [2:0]
KP3 [2:0]
KP4 [2:0]
KP5 [2:0]
Negative Polarity
PRN0 [2:0]
PRN1 [2:0]
VRN0 [3:0]
VRN1 [4:0]
KN0 [2:0]
KN1 [2:0]
KN2 [2:0]
KN3 [2:0]
KN4 [2:0]
KN5 [2:0]
Description
Variable resistor VRCP0, VRCN0
Variable resistor VRCP1, VRCN1
Variable resistor VROP0, VRON0
Variable resistor VROP1, VRON1
8-to-1 selector (voltage level of grayscale 1)
8-to-1 selector (voltage level of grayscale 8)
8-to-1 selector (voltage level of grayscale 20)
8-to-1 selector (voltage level of grayscale 43)
8-to-1 selector (voltage level of grayscale 55)
8-to-1 selector (voltage level of grayscale 62)
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 92 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
Ladder resistors and 8-to-1 selector Block configuration
The reference voltage generating block consists of two ladder resistor units including variable resistors and
8-to-1 selectors. Each 8-to-1 selector selects one of the 8 voltage levels generated from the ladder resistor
unit to output as a grayscale reference voltage. Both variable resistors and 8-to-1 selectors are controlled
according to the γ-correction registers. This unit has pins to connect a volume resistor externally to
compensate differences in various characteristics of panels.
Variable resistors
ILI9325 uses variable resistors of the following three purposes: gradient adjustment (VRCP(N)0/VRCP(N)1);
amplitude adjustment (1) (VROP(N)0); and the amplitude adjustment (2) (VROP(N)1). The resistance values
of these variable resistors are set by gradient adjustment registers and amplitude adjustment registers as
follows.
Gradient adjustment
PRP(N)0/1[2:0] VRCP(N)0
Register
Resistance
000
0R
001
4R
010
8R
011
12R
100
16R
101
20R
110
24R
111
28R
Amplitude adjustment (1)
VRP(N)0[3:0] VROP(N)0
Register
Resistance
0000
0R
0001
2R
0010
4R
:
:
:
:
1101
26R
1111
28R
1111
30R
Amplitude adjustment (2)
VRP(N)1[4:0] VROP(N)1
Register
Resistance
00000
0R
00001
1R
00010
2R
:
:
:
:
11101
29R
11110
30R
11111
31R
8-to-1 selectors
The 8-to-1 selector selects one of eight voltage levels generated from the ladder resistor unit according to the
fine adjustment register and output the selected voltage level as a reference grayscale voltage (VgP(N)1~6).
The table below shows the setting in the fine adjustment register and the selected voltage levels for
respective reference grayscale voltages.
Fine adjustment registers and selected voltage
Register
Selected Voltage
KP(N)[2:0] VgP(N)1 VgP(N)8 VgP(N)20 VgP(N)43
000
VP(N)1
VP(N)9
VP(N)17
VP(N)25
001
VP(N)2
VP(N)10
VP(N)18
VP(N)26
010
VP(N)3
VP(N)11
VP(N)19
VP(N)27
011
VP(N)4
VP(N)12
VP(N)20
VP(N)28
100
VP(N)5
VP(N)13
VP(N)21
VP(N)29
101
VP(N)6
VP(N)14
VP(N)22
VP(N)30
110
VP(N)7
VP(N)15
VP(N)23
VP(N)31
111
VP(N)8
VP(N)16
VP(N)24
VP(N)32
VgP(N)55
VP(N)33
VP(N)34
VP(N)35
VP(N)36
VP(N)37
VP(N)38
VP(N)39
VP(N)40
VgP(N)62
VP(N)41
VP(N)42
VP(N)43
VP(N)44
VP(N)45
VP(N)46
VP(N)47
VP(N)48
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 93 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
Source
Driver
Output
(S[384:1])
VCOM
Negative polarity
Postive polarity
Figure 39 Relationship between Source Output and VCOM
V0
Source Output Levels
Negative Polarity
Positive Polarity
V63
000000
GRAM Data
111111
Figure 40 Relationship between GRAM Data and Output Level
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 94 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
13. Application
13.1. Configuration of Power Supply Circuit
To Panel
VSYNC
DOTCLK
DB17
DB15
DB13
< 100 ohm
< 100 ohm
< 100 ohm
< 100 ohm
< 100 ohm
< 100 ohm
< 100 ohm
< 100 ohm
< 100 ohm
VSYNC
HSYNC
DOTCLK
ENABLE
DB17
DB16
DB15
DB14
DB13
TESTO11
DB12
DB10
DB8
3
0
DB11
DB9
< 100 ohm
<
100
ohm
< 100
100 ohm
ohm
<
< 100 ohm
< 100 ohm
DB6
DB7
DB5
DB12
DB11
DB10
DB9
DB8
TEST3
TESTO12
DB7
DB6
DB5
4
0
DB4
DB3
DB2
DB1
DB0
TESTO13
SDO
SDI
nRD
nWR/SCL
5
0
SDI
nWR
nCS
< 100 ohm
< 100 ohm
< 100 ohm
< 100 ohm
< 100 ohm
< 100 ohm
< 100 ohm
< 100 ohm
< 100 ohm
< 100 ohm
< 100 ohm
< 100 ohm
< 100 ohm
< 100 ohm
< 100 ohm
< 100 ohm
< 100 ohm
DB3
DB1
SDO
nRD
RS
Fmark
< 5 ohm
< 5 ohm
< 5 ohm
1uF/6.3V
< 5 ohm
< 5 ohm
VCL
< 5 ohm
< 5 ohm
< 5 ohm
1uF/10V
< 5 ohm
< 5 ohm
1uF/10V
C13+
C13+
C13+
C21C21C21C21C21C21C21C21+
C21+
C21+
C21+
C21+
C21+
C21+
C22C22C22C22C22C22C22C22+
C22+
C22+
C22+
C22+
C22+
C22+
DUMMY14
DUMMY15
2
4
3
< 5 ohm
VGH
VGH
VGH
DUMMY12
DUMMY13
C13C13C13C13C13+
2
4
0
< 5 ohm
VGL
VGL
VGL
VGL
GND
GND
GND
VGH
VGH
VGH
2
3
0
< 5 ohm
C11+
C11+
C11+
C11+
VGL
VGL
VGL
VGL
VGL
VGL
2
2
0
1uF/6.3V
C12+
C12+
C12+
C12+
C11C11C11C11C11C11+
2
1
0
< 5 ohm
VCI
VCI
DUMMY10
DUMMY11
C12C12C12C12C12C12+
S712
S713
S714
S715
S716
S717
S718
S719
S720
DUMMY22
2
0
0
1uF/25V
DDVDH
VCI
VCI
VCI
VCI
VCI
VCI
VCI
VCI
VCI
VCI
DUMMY23
S361
S362
S363
S364
S365
S366
S367
S368
S369
1
9
0
1uF/25V
DDVDH
VCI1
VCI1
VCI1
VCI
VCI
VCI
VCI
VCI
VCI
X
1uF/6.3V
y
< 5 ohm
S353
S354
S355
S356
S357
S358
S359
S360
DUMMY24
x
< 5 ohm
1
8
0
VCI
< 5 ohm
VCL
VCL
VCL
VCL
VCL
DDVDH
DDVDH
DDVDH
DDVDH
DDVDH
1
7
0
1uF/6.3V
< 5 ohm
VCOML
VCOML
VCOML
VCOML
VREG1OUT
VREG1OUT
VREG1OUT
DUMMY7
DUMMY8
DUMMY9
1
6
0
1uF/10V
< 10 ohm
1
5
0
1uF/6.3V
< 5 ohm
1
4
0
1uF/6.3V
< 5 ohm
1
3
0
1uF/6.3V
VCOM
VCOM
VCOM
VCOM
VCOMH
VCOMH
VCOMH
VCOMH
VCOMH
VCOMH
1
2
0
1uF/6.3V
GND
GND
GND
GND
DUMMY4
DUMMY5
DUMMY6
VCOM
VCOM
VCOM
1
1
0
< 5 ohm
1
0
0
GND
GND
VGS
VGS
GND
GND
GND
GND
GND
GND
< 5 ohm
Face Up
(Bump View)
< 5 ohm
VDDD
VDDD
VDDD
DUMMY3
GND
GND
GND
GND
GND
GND
9
0
< 5 ohm
IOVCC
IOVCC
VDDD
VDDD
VDDD
VDDD
VDDD
VDDD
VDDD
VDDD
8
0
1uF/6.3V
TS4
TS3
TS2
TS1
TS0
DUMMY2
IOVCC
IOVCC
IOVCC
IOVCC
7
0
< 5 ohm
6
0
IOVCC
RS
nCS
TESTO14
TESTO15
FMARK
TESTO16
TS8
TS7
TS6
TS5
DUMMY25
S1
S2
S3
S4
S5
S6
S7
S8
S9
…………………….
DB4
DB2
DB0
G17
G15
G13
G11
G9
G7
G5
G3
G1
DUMMY26
…………………….
< 100 ohm
HSYNC
ENABLE
DB16
DB14
…………
nRESET
TEST2
TESTO4
TESTO5
TESTO6
TESTO7
TESTO8
TESTO9
TESTO10
nRESET
nRESET
DUMMY21
G2
G4
G6
G8
G10
G12
G14
G16
G18
…………
< 100 ohm
< 100 ohm
< 100 ohm
< 100 ohm
< 100 ohm
2
0
IM0
IM2
DUMMY1
TEST1
IOGNDDUM
TESTO1
TESTO2
TESTO3
IM0/ID
IM1
IM2
IM3
1
0
IM1
IM3
DUMMY27
G319
G317
G315
G313
G311
G309
G307
G305
G303
1
< 100 ohm
G304
G306
G308
G310
G312
G314
G316
G318
G320
DUMMY20
To Panel
Figure 41 Power Supply Circuit Block
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 95 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
The following table shows specifications of external elements connected to the ILI9325’s power supply circuit.
Items
Capacity
1 µF (B characteristics)
Schottky diode
Recommended Specification
Pin connection
VREG1OUT,
6.3V
VCI1,
VDDD,
VCL,
VCOMH,
VCOML, C11+/-, C12+/-, C13+/-,
10V
DDVDH, C21+/-, C22+/-
25V
VGH, VGL
VF<0.4V/20mA at 25°C, VR ≥30V
(Recommended diode: HSC226)
(GND – VGL), (Vci – VGH), (Vci – DDVDH)
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 96 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
13.2. Display ON/OFF Sequence
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 97 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
Display Off Flow
Display On Flow
Display OFF
Power Setting
GON = 1
DTE = 1
D[1:0] = 10
ILI9325
Set SAP=1
Display On
Wait for 2 frames
or more
GON = 0
DTE = 0
D[1:0] = 01
Display OFF
GON = 1
DTE = 0
D[1:0] = 10
Wait for 2 frames
or more
Display On
Wait for 2 frames
or more
GON = 1
DTE = 0
D[1:0] = 01
Display OFF
Display On
GON = 0
DTE = 0
D[1:0] = 00
GON = 1
DTE = 0
D[1:0] = 11
Display Supply Off
Wait for 2 frames
or more
SAP = 0
AP[2:0] = 000
PON = 0
Display On
GON = 1
DTE = 1
D[1:0] = 11
Display Off
Display ON
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 98 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
Figure 42 Display On/Off Register Setting Sequence
13.3. Standby and Sleep Mode
Standby
Sleep
Display Off Sequence
Display Off Sequence
Set Standby (STB = 1)
Set Sleep (SLP = 1)
Start Oscillation
Release from Sleep
(SLP = 0)
Wait for 10 ms
Release
from
standby
Release from Standby
(STB = 0)
Release
from
Sleep
Power Supply Seeting
Display On Sequence
Power Supply Seeting
Display On Sequence
Figure 43 Standby/Sleep Mode Register Setting Sequence
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 99 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
13.4. Power Supply Configuration
When supplying and cutting off power, follow the sequence below. The setting time for oscillators, step-up
circuits and operational amplifiers depends on external resistance and capacitance.
Power Supply ON (VCC, VCI, IOVCC)
VCC
VCC
Normal Display
IOVCC VCI
GND
VCI or
IOVCC
Power On Reset
and
Display OFF
DTE=1
D[1:0]=11
GON=1
Display OFF
Sequence
VCC, IOVCC, VCI Simultaneously
1ms or more
Display ON Setting
Display OFF Setting
DTE = 0
D[1:0] = 00
GON = 0
PON = 0
Display OFF
10ms or more
Oscillator
Stabilizing time
LCD Power
Supply ON
Sequence
Registers setting
before power supply
startup
Registers setting for
power supply startup
(1)
Set VC[2:0], VRH[3:0], VCM[5;0],
VDV[5:0], PON=0
Power supply operation setting (1)
BT[2:0] = 000
Set DC1[2:0], DC0[2:0]
PON = 1
Set AP[2:0]
40ms or more
Step-up circuit
stabilizing time
Power supply operation setting (2)
Set BT[2:0]
SAP=0
AP[2:0] = 000
PON = 0
Power Supply OFF (VCC, VCI, IOVCC)
VCI IOVCC VCC
VCI
Registers setting for
power supply startup
(2)
Operational
Amplifier
stabilizing time
Power Supply
Halt Setting
Power supply initial setting
IOVCC
GND
VCC or
VCC, IOVCC, VCI Simultaneously
Power OFF Sequence
Set the other
registers
Display ON
Sequence
Set SAP=1
Display ON
DTE=1
D[1:0]=11
GON=1
Power ON Sequence
Figure 44 Power Supply ON/OFF Sequence
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 100 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
13.5. Voltage Generation
The pattern diagram for setting the voltages and the waveforms of the voltages of the ILI9325 are as follows.
VGH
BT
DDVDH
VRH
Vci
(2.5 ~ 3.3V) VC
VLCD (4.5 ~ 5.5V)
VGAM1OUT (3.0 ~ (VLCD-0.5)V )
VCM/VcomR
VCOMH (3.0 ~ (VLCD-0.5)V )
VDV
REGP,
VCI1
VGH (+9 ~ 16.5V)
VciLVL
VCOML (VCL+0.5) ~ -1V )
VCOMG
VCL
BT
VGL
VCL (0 ~ -3.3V)
VGL (-4.0 ~ -16.5V)
Figure 45 Voltage Configuration Diagram
Note: The DDVDH, VGH, VGL, and VCL output voltage levels are lower than their theoretical levels (ideal
voltage levels) due to current consumption at respective outputs. The voltage levels in the following
relationships (DDVDH – VREG1OUT ) > 0.5V, (VCOML1 – VCL) > 0.5V, (VCOML2 – VCL) > 0.5V are the
actual voltage levels. When the alternating cycles of VCOM are set high (e.g. the polarity inverts every line
cycle), current consumption is large. In this case, check the voltage before use.
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 101 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
13.6. Applied Voltage to the TFT panel
VGH
Gate
Output
VCOM
Source
output
VGL
Figure 46 Voltage Output to TFT LCD Panel
13.7. Partial Display Function
The ILI9325 allows selectively driving two partial images on the screen at arbitrary positions set in the screen
drive position registers.
The following example shows the setting for partial display function:
Base Image Display Setting
BASEE
0
NL[5:0]
6’h27
Partial Image 1 Display Setting
PTDE0
1
PTSA0[8:0]
9’h000
PTEA0[8:0]
9’h00F
PTDP0[8:0]
9’h080
Partial Image 2 Display Setting
PTDE1
1
PTSA1[8:0]
9’h020
PTEA1[8:0]
9’h02F
PTDP1[8:0]
9’h0C0
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 102 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
PTSA0=9'h000
GRAM MAP
ILI9325
LCD Panel
0 (1st line)
1 (2nd line)
2 (3rd line)
Partial Image 1
GRAM Area
PTEA0=9'h00F
PTSA1=9'h020
PTDP0=9'h080
Partial Image 2
GRAM Area
Partial Image 1
Display Area
PTEA1=9'h02F
PTDP1=9'h0C0
Partial Image 1
Display Area
319 (320th line)
Figure 47 Partial Display Example
13.8. Resizing Function
ILI9325 supports resizing function (x1/2, x1/4), which is performed when writing image data to GRAM. The
resizing function is enabled by setting a window address area and the RSZ bit which represents the resizing
factor (x1/2, x1/4) of image. The resizing function allows the system to transfer the original-size image data
into the GRAM with resized image data.
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 103 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
Original Image Data
0
1
2
3
4
5
6
ILI9325
GRAM Data
0
1
2
3
4
5
6
(0,0)
(0,1)
(0,2)
(0,3)
(0,4)
(0,5)
(0,6)
(1,0)
(1,1)
(1,2)
(1,3)
(1,4)
(1,5)
(1,6)
(0,0)
(0,2)
(0,4)
(0,6)
(2,0)
(2,1)
(2,2)
(2,3)
(2,4)
(2,5)
(2,6)
(2,0)
(2,2)
(2,4)
(2,6)
(3,0)
(3,1)
(3,2)
(3,3)
(3,4)
(3,5)
(3,6)
(4,0)
(4,2)
(4,4)
(4,6)
(4,0)
(4,1)
(4,2)
(4,3)
(4,4)
(4,5)
(4,6)
(6,0)
(6,2)
(6,4)
(6,6)
(5,0)
(5,1)
(5,2)
(5,3)
(5,4)
(5,5)
(5,6)
(6,0)
(6,1)
(6,2)
(6,3)
(6,4)
(6,5)
(6,6)
? resizing
Figure 48 Data transfer in resizing
Original Data
240
Panel Display
120
Write to GRAM
160
320
RSZ=2'h1
Figure 49 Resizing Example
Original Image Size (X × Y)
640 × 480
352 × 288
320 × 240
176 × 144
120 × 160
132 × 132
Resized Image Resolution
1/2 (RSZ=2’h1) 1/4 (RSZ=2’h3)
320 × 240
160 × 120
176 × 144
88 × 72
160 × 120
80× 60
88 × 72
44× 36
60× 80
30 × 40
66 × 66
33 × 33
The RSZ bit sets the resizing factor of an image. When setting a window address area in the internal GRAM,
the GRAM window address area must fit the size of resized image. The following example show the resizing
setting.
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 104 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
X
GRAM Address
(X0, Y0)
Y
ILI9325
Original Image
Size
dx= (X-H)/N, H=X mod N
dy= (Y-V)/N, V=Y mod N
dx
dy
(X0+dx-1, Y0+dy-1)
Original image data number in horizontal direction
X
Original image data number in Vertical direction
Y
Resizing Ration
1/N
Resizing Setting
RSZ
N-1
Remainder pixels in horizontal direction
RCH
H
Remainder pixels in vertical direction
RCV
V
GRAM writing start address
AD
(x0, y0)
HSA
x0
HEA
x0+dx-1
VSA
y0
VEA
y0+dy-1
GRAM window setting
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 105 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
14. Electrical Characteristics
14.1. Absolute Maximum Ratings
The absolute maximum rating is listed on following table. When ILI9325 is used out of the absolute maximum
ratings, the ILI9325 may be permanently damaged. To use the ILI9325 within the following electrical
characteristics limit is strongly recommended for normal operation. If these electrical characteristic conditions
are exceeded during normal operation, the ILI9325 will malfunction and cause poor reliability.
Item
Symbol
Unit
Power supply voltage (1)
VCC, IOVCC
V
Power supply voltage (1)
VCI - GND
V
Power supply voltage (1)
DDVDH - GND
V
Power supply voltage (1)
GND -VCL
V
Power supply voltage (1)
DDVDH - VCL
V
Power supply voltage (1)
VGH - GND
V
Power supply voltage (1)
GND - VGL
V
Input voltage
Vt
V
Operating temperature
Topr
°C
Storage temperature
Tstg
°C
Notes:
1. VCC,DGND must be maintained
2. (High) (VCC = VCC) ≥ DGND (Low), (High) IOVCC ≥ DGND (Low).
3. Make sure (High) VCI ≥ DGND (Low).
4. Make sure (High) DDVDH ≥ ASSD (Low).
5. Make sure (High) DDVDH ≥ VCL (Low).
6. Make sure (High) VGH ≥ ASSD (Low).
7. Make sure (High) ASSD ≥ VGL (Low).
8. For die and wafer products, specified up to 85°C.
9. This temperature specifications apply to the TCP package
Value
-0.3 ~ + 4.6
-0.3 ~ + 4.6
-0.3 ~ + 6.0
-0.3 ~ + 4.6
-0.3 ~ + 9.0
-0.3 ~ + 18.5
-0.3 ~ + 18.5
-0.3 ~ VCC+ 0.3
-40 ~ + 85
-55 ~ + 110
Note
1, 2
1, 4
1, 4
1
1, 5
1, 5
1, 6
1
8, 9
8, 9
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 106 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
14.2. DC Characteristics
(VCC = 2.40 ~ 3.30V, IOVCC = 1.65 ~ 3.30V, Ta= -40 ~ 85 °C)
Item
Symbol
Unit
Test Condition
Min.
Typ.
Max.
Note
Input high voltage
VIH
V
VCC= 1.8 ~ 3.3V
0.8*IOVCC
-
IOVCC
-
Input low voltage
VIL
V
VCC= 1.8 ~ 3.3V
-0.3
-
0.2*IOVCC
-
VOH1
V
IOH = -0.1 mA
0.8*IOVCC
-
-
-
VOL1
V
-
-
0.2*IOVCC
-
ILI
µA
-0.1
-
0.1
-
IOP
µA
-
-
IST
µA
Output high voltage(1)
( DB0-17 Pins)
Output low voltage
( DB0-17 Pins)
I/O leakage current
Current consumption
during normal operation
(VCC – DGND )
IOVCC=1.65~3.3V
VCC= 2.4 ~ 3.3V IOL = 0.1mA
Vin = 0 ~ VCC
VCC=2.8V , Ta=25°C , fOSC = 512KHz
( Line) GRAM data = 0000h
100
-
(VCC)
Current consumption
during standby mode
VCC=2.8V , Ta=25 °C
-
5
10
-
-
3.0
-
-
(VCC – DGND )
VCC=2.8V , VREG1OUT =4.8V
DDVDH=5.0V , fOSC = 512KHz (320
LCD Drive Power Supply
line) , Ta=25 °C, GRAM data = 0000h,
Current
ILCD
mA
( DDVDH-DGND )
REV=”0”, SAP=”001”, ON4-0=”0”,
OP4-0=”0”, MP52-00=”0”,
MN52-00=”0”, CP12-00=”0”
CN12-00=”0
LCD Driving Voltage
DDVDH
( DDVDH-DGND )
Output voltage deviation
Dispersion of the Average
V
Output Voltage
V
-
4.5
-
6
-
mV
-
-
10
-
-
mV
-
-10
-
10
-
14.3. Reset Timing Characteristics
Reset Timing Characteristics (VCC = 1.8 ~ 3.3 V, IOVCC = 1.65 ~ 3.3 V)
Item
Symbol Unit
Min.
Typ.
Max.
Reset low-level width
tRES
ms
1
-
-
Reset rise time
trRES
µs
-
-
10
tRES
nRESET
trRES
VIH
VIL
14.4. LCD Driver Output Characteristics
Item
Driver
output
delay
time
Symbol
tdd
Timing diagram
VCC=2.8V, DDVDH=5.0V, VREG1OUT =4.8V,
RC oscillation: fosc =512kHz (320 lines),
Ta=25°C REV=0, SAP=010, AP=010, 0N14-00=0,
0P14-00=0, MP52-00=0, MN52-00=0, CP12-00=0,
CN12-00=0, Load resistance R=10kΩ, Load capacitance
C=20pF • when the level changes from a same grayscale
level on all pins • Time to reach +/-35mV when VCOM
polarity inverts
Min.
Typ.
Max.
Unit
-
35
-
µs
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 107 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
14.5. AC Characteristics
14.5.1. i80-System Interface Timing Characteristics
Normal Write Mode (IOVCC = 1.65~3.3V, VCC=2.4~3.3V)
Item
Bus cycle time
Write
Read
Write low-level pulse width
Write high-level pulse width
Read low-level pulse width
Read high-level pulse width
Write / Read rise / fall time
Write ( RS to nCS, E/nWR )
Setup time
Read ( RS to nCS, RW/nRD )
Address hold time
Write data set up time
Write data hold time
Read data delay time
Read data hold time
RS
Symbol
Unit
Min.
Typ.
Max.
tCYCW
ns
100
-
-
-
tCYCR
PWLW
PWHW
PWLR
PWHR
tWRr/tWRf
ns
ns
ns
ns
ns
ns
300
50
50
150
150
ns
tAH
ns
ns
ns
ns
ns
500
25
100
-
-
tAS
-
tDSW
tH
tDDR
tDHR
10
5
5
10
15
5
VIH
VIL
Test Condition
VIH
VIL
tAH
tAS
nCS
PWLW, PWLR
VIH
nWR, nRD
tWRf
PWHW, PWHR
VIH
VIL
VIL
VIH
tWRr
tDSW
VIH
VIL
Write Data
DB[17:0]
tH
VIH
VIL
Valid Data
tDHR
tDDR
Read Data
DB[17:0]
tCYCW, tCYCR
VOH
VOL
Valid Data
VOH
VOL
Figure 50 i80-System Bus Timing
14.5.2. Serial Data Transfer Interface Timing Characteristics
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 108 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
(IOVCC= 1.653.3V and VCC=2.4~3.3V)
Item
Serial clock cycle time
Serial clock high – level
pulse width
Serial clock low – level
pulse width
Write ( received )
Read ( transmitted )
Write ( received )
Read ( transmitted )
Write ( received )
Read ( transmitted )
Serial clock rise / fall time
Chip select set up time
Chip select hold time
Serial input data set up time
Serial input data hold time
Serial output data set up time
Serial output data hold time
nCS
Symbol
Unit
Min.
Typ.
Max.
tSCYC
µs
100
-
-
tSCYC
tSCH
tSCH
tSCL
tSCL
tSCr, tSCf
tCSU
tCH
tSISU
tSIH
µs
ns
ns
ns
ns
ns
ns
ns
ns
ns
200
40
100
40
100
10
50
20
20
-
5
-
tSOD
tSOH
ns
-
-
100
ns
5
-
-
VIH
VIL
tCSU
tSCr
VIH
VIL
SCL
Test Condition
VIL
tSCH
VIH
tSCf
tSCL
VIH
VIL
tCH
VIL
VIH
tSIH
tSISU
SDI
tSCYC
VIH
VIL
Input Data
VIH
VIL
Input Data
VOH
VOL
Output Data
VOH
VOL
Output Data
tSOD
SDO
VOH
VOL
Figure 51 SPI System Bus Timing
14.5.3. RGB Interface Timing Characteristics
18/16-bit Bus RGB Interface Mode (IOVCC = 1.65 ~ 3.3V, VCC=2.4~3.3V)
Item
VSYNC/HSYNC setup time
ENABLE setup time
ENABLE hold time
PD Data setup time
PD Data hold time
DOTCLK high-level pulse width
DOTCLK low-level pulse width
DOTCLK cycle time
DOTCLK, VSYNC, HSYNC, rise/fall time
Symbol
tSYNCS
tENS
tENH
tPDS
Unit
ns
ns
ns
ns
Min.
0
10
10
10
Typ.
-
Max.
-
Test Condition
-
tPDH
ns
40
-
-
-
PWDH
PWDL
tCYCD
trghr, trghf
ns
ns
ns
ns
40
40
100
-
-
25
-
Typ.
Max.
Test Condition
6-bit Bus RGB Interface Mode (IOVCC = 1.65 ~ 3.3V, VCC=2.4~3.3V)
Item
Symbol
Unit
Min.
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 109 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
VSYNC/HSYNC setup time
ENABLE setup time
ENABLE hold time
PD Data setup time
PD Data hold time
DOTCLK high-level pulse width
DOTCLK low-level pulse width
DOTCLK cycle time
DOTCLK, VSYNC, HSYNC, rise/fall time
trgbf
trgbr
tSYNCS
tENS
tENH
tPDS
ns
ns
ns
ns
0
10
10
10
ILI9325
-
-
-
tPDH
ns
30
-
-
-
PWDH
PWDL
tCYCD
trghr, trghf
ns
ns
ns
ns
30
30
80
-
-
25
-
tSYNCS
VIH
VIL
HSYNC
VSYNC
tASE
tENS
tENH
VIH
VIL
HSYNC
VSYNC
trgbf
VIH
PWDL
VIL
VIH
VIL
trgbr
VIL
PWDH
VIH
VIH
tCYCD
tPDS
VIH
VIL
tPDH
Write Data
VIH
VIL
Figure52 RGB Interface Timing
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 110 of 111
Version: 0.28
a-Si TFT LCD Single Chip Driver
240RGBx320 Resolution and 262K color
ILI9325
15. Revision History
Version No.
Date
V0.28
2007/07/05
Page
96
Description
Modify the FPC circuit
The information contained herein is the exclusive property of ILI Technology Corp. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of ILI Technology Corp.
Page 111 of 111
Version: 0.28