ROHM SE3002

SE3002-DC90A
Tentative
Printheads
Under development
High speed thermal printhead
(300 dots / inch)
SE3002-DC90A
High speed, high quality, and high durability are achieved by using step free structure with high performance partial glaze
and highly conductive overcoat layer. SE300*-DC90A series are lined up which can accommodate with all types of
barcode labeling printers from Direct to Thermal Transfer, normal to high speed (over 300mm/s).
zApplications
Bar code printer
Label printer
Packaging printer
ATM
Ticket printer
zFeatures
1) ROHM new technology “STEP FREE” structure will provide, high corrosion resistance, better resistance against
scratching damage, high efficiency.
2) Standard glazed components to accommodate thick paper.
3) High speed clock to facilitate external heat history control.
4) Using a hard conductive film as a protective film on the heating element offers excellent resistance to electrostatic
damage.
zExternal dimensions (Unit : mm)
DOT No.1
DOT No.640
MAX.φ20
6±0.5
66±0.5
54.208 (Effective print width)
MAX.48
MIN.4.3
(3.5)
(5.896)
MAX.5
#2
#20
CONNECTOR:A
#4
#1
CONNECTOR:B
#1
MAX.10
φ3 H10 Length 4
Effective Depth 3
(21.3)
17.8±0.2
25±0.5
(36)
7.3±0.3
#19
20±0.3
(13)
φ3 H10
Effective Depth 3
7.104±0.3
40±0.3
M3
Effective Depth 3
Note : No heat history control function inside the thermal printhead. External heat history control is required for high speed printing.
1/3
SE3002-DC90A
Tentative
Printheads
Under development
zEquivalent circuit
DOT#640
DOT#1
VH (COM)
220µF
35V
#640
#321
#320
#1
VDD
0.1µF
50V
GND
BEO
/STB2
/STB1
LATCH REGISTER
/LAT
CLK
SHIFT
REGISTER
DI2
SHIFT
REGISTER
DI1
SENS1
SENS2
SENS3
TM
TM
DI No.
DOT No.
STB No.
DI2
640 to 321
STB2
640 to 321
DI1
320 to
STB1
320 to
1
DOT No.
1
2/3
SE3002-DC90A
Tentative
Printheads
Under development
zPin assignments
No.
Circuit
No.
Circuit
No.
Circuit
1
VDD
2
BEO
1
VH
3
GND
4
DI2
2
VH
5
N.C.
6
CLK
3
VH
7
LAT
8
GND
4
GND
9
GND
10
DI1
5
GND
11
N.C.
12
GND
6
GND
13
VDD
14
STB2
15
STB1
16
TM
17
TM
18
SENS1
19
SENS2
20
SENS3
zCharacteristics
Symbol
Typical
Unit
Effective printing width
−
54.2
mm
Dot pitch
−
0.0847
mm
Total dot number
−
640
dots
Rave
850
Ω
VH
24
V
Parameter
Average resistance value
Applied voltage
Applied power
PO
0.59
W / dot
SLT
0.42
ms
Maximum number of dots energized simultaneously
−
640
dots
Maximum clock frequency
−
8
MHz
Maximum roller diameter
−
φ 20
mm
Running life / pulse life
−
150 / 108
km / pulses
Operating temperature
−
5 to 45
°C
Print cycle
3/3
Appendix
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from or connected with or related
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or
otherwise dispose of the same, no express or implied right or license to practice or commercially
exploit any intellectual property rights or other proprietary rights owned or controlled by
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document are no antiradiation design.
The products listed in this document are designed to be used with ordinary electronic equipment or devices
(such as audio visual equipment, office-automation equipment, communications devices, electrical
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level of
reliability and the malfunction of with would directly endanger human life (such as medical instruments,
transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other
safety devices), please be sure to consult with our sales representative in advance.
About Export Control Order in Japan
Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control
Order in Japan.
In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause)
on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction.
Appendix1-Rev1.1