SKYPER PRIME 1000A / 1700V ST10 / PP
Absolute Maximum Ratings
SKYPER
®
Symbol
Conditions
Values
Unit
Vs
Supply voltage primary
ViH
Input signal voltage (HIGH)
16
V
Vs + 0.3
V
ViL
Input signal voltage (LOW)
GND - 0.3
V
IoutPEAK
Output peak current
15
A
IoutAVmax
Output average current
100
mA
fmax
Max. switching
frequency 85°C
10
kHz
kHz
VCE
IGBT Driver for Primepack
and SEMITRANS 10
Collector emitter voltage sense across
the IGBT
dv/dt
Rate of rise and fall of voltage
secondary to primary side
Order Nr. L5066801
Visol IO
Insulation test voltage input - output
(AC, rms, 2s)
Qout/pulse
Max. rating for output charge per pulse
Top
Operating temperature
-40 ... 85
°C
Tstg
Storage temperature
-40 ... 85
°C
SKYPER PRIME 1000A / 1700V
ST10 / PP
1700
V
50
kV/µs
5000
V
10
µC
Characteristics
Features
• Dynamic short circuit detection with
SoftOff
• Galvanic isolated DC link
measurement
• Galvanic isolated temp measurement
• PWM output for sensor signals
• Over voltage trip
• ROHS, UL recognized
• DC Bus up to 1200V
Typical Applications*
• Regenerative inverters
• Traction
• Large drives
Remarks
• For environmental conditions please
check technical explanation
• The driver has to be 100% tested for
high voltage before use
Symbol
Conditions
min.
Vs
Supply voltage primary side
14.4
IS0
Supply current primary (no load)
typ.
max.
15
15.6
85
Supply current primary side (max.)
Unit
V
mA
1000
mA
Vi
Input signal voltage on / off
VIT+
Input treshold voltage (HIGH)
8.6
10
VIT-
Input threshold voltage (LOW)
5
6.7
RIN
Input resistance (switching signal)
30
kΩ
CIN
Input capacitance (switching signals)
1
nF
VG(on)
Turn on output voltage
15
V
VG(off)
Turn off output voltage
-8
V
td(on)IO
Input-output turn-on propagation time
1
µs
td(off)IO
Input-output turn-off propagation time
1
µs
td(err)SCP
Error sec - prim propagation time
0.6
µs
td(err)HALT
Error primary - secondary side
propagation time
0.6
µs
tTD
Top-Bot interlock dead time
4
µs
tjitter
Signal transfer prim - sec (total jitter)
25
ns
tSIS
Short pulse suppression
0.4
µs
tPOR
Power-On-Reset completed
tpRESET
Error reset time
VCEstat
Reference voltage for VCE-monitoring
tbl
VCE monitoring blanking time (
dynamic )
VDCtrip
Over voltage trip level
RGon
Driver gate resistor at switch-on
Vs/0
0.1
0.03
V
V
V
s
ms
8.5
V
4
µs
1250
V
0.4
Ω
RGoff
Driver gate resistor at switch-off
5
Ω
MTBF
Mean Time Between Failure Ta = 40°C
3
106h
Two channel driver
© by SEMIKRON
Rev. 3.0 – 30.11.2015
1
SKYPER PRIME 1000A / 1700V ST10 / PP
Signal Connector
PIN
Signal
Function
Specifications
X1:01
IF_PWR_15P
Drive power supply
Stabilised +15V ±4%
X1:02
IF_DC_LINK
Digitised DC Link signal
PWM output, 15V
X1:03
IF_PWR_15P
Drive power supply
Stabilised +15V ±4%
X1:04
IF_GND
GND
To be connected to ground
X1:05
IF_PWR_15P
Drive power supply
Stabilised +15V ±4%
X1:06
IF_GND
GND
To be connected to ground
X1:07
IF_nERROR_IN
ERROR input
LOW ( GND, UTH 1V ) = External error
HIGH ( VP, UTH 14V ) = No error
Max input current 1,8mA, can be
connected with IF_nERROR_OUT
X1:08
IF_GND
GND
To be connected to ground
X1:09
IF_nERROR_OUT
ERROR output
HIGH = NO ERROR ;open collector output
15V / 10mA (external pull up
Resistor necessary )
X1:10
IF_GND
GND
To be connected to ground
X1:11
IF_HB_TOP
Switching signal input ( TOP switch )
Positive 15V CMOS logic,
LOW = TOP switch off ;
HIGH = TOP switch on
X1:12
IF_GND
GND
To be connected to ground
X1:13
IF_nERROR_OUT
ERROR output
HIGH = NO ERROR; open collector
output; max. 15V / 10 mA (external
pull up resistor necessary )
X1:14
IF_GND
GND
To be connected to ground
X1:15
IF_HB_BOT
Switching signal input ( BOTTOM switch )
Positive 15V CMOS logic,
LOW = BOT switch off;
HIGH = BOT switch on
X1:16
IF_GND
GND
To be connected to ground
X1:17
IF_CFG_SELECT
Interlock set up
HIGH (VP) = No interlock
LOW (GND) = Interlock 4µs
X1:18
IF_GND
GND
To be connected to ground
X1:19
IF_TEMP
Digitised NTC signal
PWM output, 15V
X1:20
IF_GND
GND
To be connected to ground
This is an electrostatic discharge sensitive device (ESDS), international standard IEC 60747-1, chapter IX.
*IMPORTANT INFORMATION AND WARNINGS
The specifications of SEMIKRON products may not be considered as guarantee or assurance of product characteristics
("Beschaffenheitsgarantie"). The specifications of SEMIKRON products describe only the usual characteristics of products to be expected in
typical applications, which may still vary depending on the specific application. Therefore, products must be tested for the respective
application in advance. Application adjustments may be necessary. The user of SEMIKRON products is responsible for the safety of their
applications embedding SEMIKRON products and must take adequate safety measures to prevent the applications from causing a physical
injury, fire or other problem if any of SEMIKRON products become faulty. The user is responsible to make sure that the application design is
compliant with all applicable laws, regulations, norms and standards. Except as otherwise explicitly approved by SEMIKRON in a written
document signed by authorized representatives of SEMIKRON, SEMIKRON products may not be used in any applications where a failure of
the product or any consequences of the use thereof can reasonably be expected to result in personal injury. No representation or warranty is
given and no liability is assumed with respect to the accuracy, completeness and/or use of any information herein, including without limitation,
2
Rev. 3.0 – 30.11.2015
© by SEMIKRON
SKYPER PRIME 1000A / 1700V ST10 / PP
warranties of non-infringement of intellectual property rights of any third party. SEMIKRON does not assume any liability arising out of the
applications or use of any product; neither does it convey any license under its patent rights, copyrights, trade secrets or other intellectual
property rights, nor the rights of others. SEMIKRON makes no representation or warranty of non-infringement or alleged non-infringement of
intellectual property rights of any third party which may arise from applications. Due to technical requirements our products may contain
dangerous substances. For information on the types in question please contact the nearest SEMIKRON sales office. This document
supersedes and replaces all information previously supplied and may be superseded by updates. SEMIKRON reserves the right to make
changes.
© by SEMIKRON
Rev. 3.0 – 30.11.2015
3