VPC’s VTAC High Speed Data (HSD) connectors allow engineers in multiple industries to test devices that communicate at greater speeds and require higher data rates. The VTAC HSD insert features a data transfer rate of 12.5+ Gbps per differential pair. Each VTAC HSD 50 µ" gold-plated, self-aligning contact has been tested and verified to 10,000 cycles without signal degradation. VTAC HSD insert FEATURES AND BENEFITS » Modular: VTAC contacts work in both the iSeries and 90 Series connector families » Scalable: Customize between 8-272 individual contacts » Reconfigurable: Arrange VTAC inserts in desired location and rearrange to fit requirement needs » Compatible: With multiple HSD standards USB 3.0, Serial ATA, HDMI, DVI & DVI-1, RJ45 Gigabit Ethernet, QSFP, Twinax and Infiniband (more standards available) www.vpc.com/VTAC SPECIFICATIONS VTAC HSD precision-welded inserts reduce resistance and increase signal integrity with a seamless transition from wire to connector. Signal degradation is inherent in all digital circuits, therefore our engineers designed a solution that would minimize degradation. Although there are many factors that influence signal integrity, insertion loss was a concern during testing. Insertion loss is a loss in signal that originates from energy loss, impedance mismatches, and subsequent signal reflections. As the rise and fall times of a square waveform begin to vary, they can degrade the signal. If the connector creates impedance mismatch, the signal risks being reflected back unto itself creating a loss of signal. The figure below shows the insertion loss of a one meter long cable with a small form-factor pluggable (SFP+) as a point of reference and a second cable with a SFP+ terminated with VTAC HSD inserts in its center. The VTAC HSD shows no significant deviation from the SFP+ signal until approximately 6.25 GHz. The industry benchmark for insertion loss is -3dB, or approximately 50% signal loss. At 6.25 GHz, there is only -1dB of difference between the SFP+ and the SFP+ terminated with the VTAC HSD in its center. This equates to approximately a 10% loss compared to the SFP+ only. These results were consistent for 10,000 cycles. Data Rate Crosstalk Characteristic Impedance Operating Voltage and Current Contact Resistance 12.5+ Gbps per Differential Pair 30 dB min 100 +/- 10 ohms Differential Pair 50 +/- 5 ohms Single Ended 3 Amps Max. Continous (350V max) 30 mohms Max. per Mated Contact 1000 mohms Min Insulation Reistance Dielectric 750 VAC rms Min. Withstanding Voltage 12 oz Max. [340 Mating Force gm] per Insert Outer Shell - Black or Blue LCP Insert Male Contact - Alloy 7025 Contact Termination Welded 50µ" Au over 100µ" Contact Plating Ni VTAC HSD RIGHT ANGLE FEATURES AND BENEFITS The VTAC HSD right angle inserts are ideal for a variety of applications that require a wireless solution for your project. Choosing VTAC HSD will help to consolidate connections for rapid integration and connection to instrumentation. You can choose to use the VTAC HSD right angle as a complete wireless PCB (direct to instrument card) or with PCB adapters. The new VTAC HSD right angle inserts are also ideal for Pull-Thru applications. While VPC’s PullThru adapters can accommodate both wired and PCB options, now you can connect directly to your instrumentation with speeds of 10+ Gbps. To learn more about VPC’s Pull-Thru product line visit vpc.com/PullThru. VTAC QUADRAPADDLE INSERTS FEATURES AND BENEFITS Not every application requires high speed data (HSD) transfer. We also offer a VTAC QuadraPaddle insert for signal or lower speed applications. You can outfit an i2 MX, and VTAC 90 Series with both low and high speed module inserts, giving you increased scalability and versatility to meet any project’s needs. INSERT SPECIFICATIONS 5 Amps Max. Operating Voltage & Continuous; 600 Current volt Max. use of wire Mil-W-16878/4 25 mohms Max. Contact Resistance Measured at 50 mV @100 mA Mating Force per Contact 6 oz. Nominal [0.15Kg] Dielectric Withstanding 1500 VDC Min. Voltage Insulation Resistance 5000 mohms Min. Cycle Life 20,000 Cycles D C A A F B F E A. RCV/ITA VTAC HSD Patchcords C. Receiver Module E. ITA Module B. Strain Relief Plate D. VTAC HSD Inserts F. RCV/ITA VTAC QuadraPaddle Flying Leads Pa r t # RECEIVER 310 130 113 510 170 101 ITA 410 130 116 510 171 101 PATCHCORDS* 7-142890690-0XX 7-142891693-0XX 7-142892700-0XX 7-142893694-0XX 7-142861000-0XX 7-142895000-0XX 7-141890690-0XX 7-141891693-0XX 7-141892700-0XX 7-141893694-0XX 7-141861000-0XX 7-141895000-0XX Description For a complete list of VTAC HSD product offerings visit vpc.com/VTAC Receiver, i2 MX, 2 VTAC Module Inserts, EMI-Shielded VTAC Module, Receiver, 90 Series, 34 Position ITA, i2 MX, 2 VTAC Module Inserts, EMI Backshell VTAC Module, ITA, 90 Series, 34 Position Signal Patchcord, Receiver, VTAC, USB 3.0 Type A Male Signal Patchcord, Receiver, VTAC, HDMI Male Signal Patchcord, Receiver, VTAC, SATA Male Signal Patchcord, Receiver, VTAC, RJ45 Plug Signal Patchcord, Receiver, VTAC, Twinax Flying Leads Signal Patchcord, Receiver, VTAC, 24 AWG, Flying Leads Signal Patchcord, ITA, VTAC HSD, USB 3.0 Type A Male Signal Patchcord, ITA, VTAC HSD, HDMI Male Signal Patchcord, ITA, VTAC HSD, SATA Male Signal Patchcord, ITA, VTAC HSD, RJ45 Plug Signal Patchcord, ITA, VTAC, Twinax Flying Leads Signal Patchcord, ITA, VTAC, 24 AWG, Flying Leads CABLE ASSEMBLIES 7-152924000-0XX 7-151924000-0XX ACCESSORIES 310 113 681 510 119 568 610 111 102 910 112 130 910 112 131 Receiver, VTAC QuadraPaddle Insert, Flying Leads ITA, VTAC QuadraPaddle Insert, Flying Leads Strain Relief Plate, i2 MX, Receiver Strain Relief Plate for 34 Position Receiver/ITA VTAC Module Blank Insert Kit, Receiver/ITA, VTAC HSD, 10 Positions Extraction Tool, VTAC HSD, Receiver/ITA Extraction Tool, VTAC QuadraPaddle Insert, Receiver/ITA *NOTE: All inserts are custom welded using a VPC precision welding process. Contact us for more information on additional lengths. vpc.com/VTAC NORTH AND SOUTH AMERICA EUROPE, MIDDLE EAST, AFRICA 1400 New Hope Road Karlstrasse 32 Waynesboro, VA 22980 72666 Neckartailfingen United States Germany Phone: +1 540 932 3300 Phone: +49 1522 755 4545 Email: [email protected] Email: [email protected] ASIA, AUSTRALIA PO Box 86098 140 Gillies Avenue Hung Hom, Kowloon Hong Kong Phone: +852 2356 8635 Email: [email protected]