AS4SD8M16

SDRAM
AS4SD8M16
128 Mb: 8 Meg x 16 SDRAM
PIN ASSIGNMENT
(Top View)
Synchronous DRAM Memory
54-Pin TSOP
FEATURES
• Full Military temp (-55°C to 125°C) processing available
• Configuration: 8 Meg x 16 (2 Meg x 16 x 4 banks)
• Fully synchronous; all signals registered on positive edge of system clock
• Internal pipelined operation; column address can be changed every clock cycle
• Internal banks for hiding row access/precharge
• Programmable burst lengths: 1, 2, 4, 8 or full page
• Auto Precharge, includes CONCURRENT AUTO
PRECHARGE and Auto Refresh Modes
• Self Refresh Mode (IT & ET)
• 64ms, 4,096-cycle refresh (IT)
• 24ms 4,096 cycle recfresh (XT)
• WRITE Recovery (tWR = “2 CLK”)
• LVTTL-compatible inputs and outputs
• Single +3.3V ±0.3V power supply
OPTIONS
• Plastic Package
54-pin TSOPII (400 mil)
(Pb/Sn finish or RoHS available)
• Timing (Cycle Time)
7.5ns @ CL = 3 (PC133) or 10ns @ CL = 2 (PC100)
• Operating Temperature Ranges
-Industrial Temp (-40°C to 85° C)
-Enhanced Temp (-40°C to +105°C) -Military Temp (-55°C to 125°C)
VDD
DQ0
VDDQ
DQ1
DQ2
VSSQ
VDD
14
41
DQML
15
40
WE\
16
39
DQMH
CAS\
17
38
CLK
RAS\
18
37
CKE
CS\
19
36
NC
BA0
20
35
A11
BA1
21
34
A9
A10
22
33
A8
A0
23
32
A7
A1
24
31
A6
A2
25
30
A5
A3
26
29
A4
27
28
Vss
VSSQ
DG No. 901
-75
VDD
IT
ET
XT
SETUP
TIME
1.5ns
1.5ns
46
45
44
43
42
Package may or may not be
assembled with a location notch.
8 Meg x 16
Configuration
2 Meg x 16 x 4 banks
Refresh Count
4K
Row Addressing
4K (A0-A11)
Bank Addressing
4 (BA0, BA1)
Column Addressing
512 (A0-A8)
HOLD
TIME
0.8ns
0.8ns
Note: “\” indicates an active low.
*Off-center parting line
**CL = CAS (READ) latency
AS4SD8M16
Rev. 1.6 March 27, 2015
DQ7
DQ12
DQ11
VSSQ
DQ10
DQ9
VDDQ
DQ8
VSS
NC
DQ6
KEY TIMING PARAMETERS
SPEED
CLOCK
ACCESS TIME
GRADE FREQUENCY CL = 2** CL = 3**
-75
133 MHz
–
5.4ns
-75
100 MHz
6ns
–
54
53
52
51
50
49
48
47
DQ3
DQ4
VDDQ
DQ5
MARKING
VSS
DQ15
VSSQ
DQ14
DQ13
VDDQ
1
2
3
4
5
6
7
8
9
10
11
12
13
For more products and information
please visit our web site at www.micross.com
Micross Components reserves the right to change products or specifications without notice.
1
SDRAM
AS4SD8M16
GENERAL
DESCRIPTION
IS45S81600E,
IS45S16800E
The 128Mb SDRAM is a high-speed CMOS, dynamic
random-access memory containing 134, 217, 728 bits. It is
DEVICE OVERVIEW
internally configured as a quad-bank DRAM with a
The 128Mb SDRAM is a high speed CMOS, dynamic
synchronous
interface (all signals are registered on the
random-accessmemorydesignedtooperatein3.3VVdd
positive
edge
of
the clock signal, CLK). Each of the 33, 554,
and3.3VVddq memorysystemscontaining134,217,728
432-bit
banks
is
organized as 4,096 rows by 512 columns by
bits.Internallyconfiguredasaquad-bankDRAMwitha
16 bits.
synchronousinterface.Each33,554,432-bitbankisorga nizedas4,096rowsby512columnsby16bitsor4,096
Read and write accesses to the SDRAM are burst orirowsby1,024columnsby8bits.
ented;
accesses start at a selected location and continue for a
programmed
number of locations in a programmed sequence.
The128MbSDRAMincludesanAUTOREFRESHMODE,
and abegin
power-saving,
power-down
All signals
are
Accesses
with the registration
ofmode.
an ACTIVE
command,
registeredonthepositiveedgeoftheclocksignal,CLK.
which
is then followed by a READ or WRITE command. The
AllinputsandoutputsareLVTTLcompatible.
address
bits registered coincident with the ACTIVE command
The128MbSDRAMhastheabilitytosynchronouslyburst
are used
to select the bank and row to be accessed (BA0, BA1
dataatahighdataratewithautomaticcolumn-address
select
the bank; A0-A11 select the row). The address bits
generation,theabilitytointerleavebetweeninternalbanks
registered coincident with the READ or WRITE command
to hide precharge time and the capability to randomly
are used
to select
the
starting column
for the
burst
change
column
addresses
on eachlocation
clock cycle
during
access.
burstaccess.
The SDRAM provides for programmable READ or
WRITE burst lengths of 1, 2, 4, or 8 locations, or the full page,
with a burst terminate option. An auto precharge function may
be enabled to provide a self-timed row precharge that is initiated
at the end of the burst sequence.
Aself-timedrowprechargeinitiatedattheendoftheburst
The 128Mb SDRAM uses an internal pipelined
architecture
to achieve high-speed operation. This
sequenceisavailablewiththeAUTOPRECHARGEfunction
architecture
is
compatible with the 2n rule of prefetch
enabled. Prechargeonebankwhileaccessingoneofthe
architectures,
but it also allows the column address to be
otherthreebankswillhidetheprechargecyclesandprovide
seamless,high-speed,random-accessoperation.
changed
on every clock cycle to achieve a high-speed, fully
random
operation. Precharging one bank while accessing one of
SDRAMreadandwriteaccessesareburstorientedstarting
ataselectedlocationandcontinuingforaprogrammed
the
other three banks will hide the precharge cycles and provide
number ofhigh-speed,
locations in
a programmed
sequence.The
seamless,
random-access
operation.
of an
ACTIVEiscommand
begins
accesses,
registration
The 128Mb
SDRAM
designed to
operate
in 3.3V memfollowedbyaREADorWRITEcommand.TheACTIVE
ory systems. An auto refresh mode is provided, along with a
commandinconjunctionwithaddressbitsregisteredare
power-saving,
and(BA0,
outputs are
used to selectpower-down
the bank andmode.
row toAll
be inputs
accessed
LVTTL-compatible.
BA1selectthebank;A0-A11selecttherow).TheREAD
or WRITE
SDRAMs
offer substantial
advances
DRAM bits
operating
commands
in conjunction
withinaddress
registeredareusedtoselectthestartingcolumnlocation
performance,
including the ability to synchronously burst data at
afortheburstaccess.
high data rate with automatic column-address generation, the
ProgrammableREADorWRITEburstlengthsconsistof
ability
to interleave between internal banks to hide precharge
1,2,4and8locationsorfullpage,withaburstterminate
time
and the capability to randomly change column addresses
option.
on
each clock cycle during a burst access.
FUNCTIONAL BLOCK FUNCTIONAL
DIAGRAM (FOR 2MX16X4
BANKSDIAGRAM
ONlY)
BLOCK
COMMAND
DECODER
&
CLOCK
GENERATOR
16
16
REFRESH
CONTROLLER
MODE
REGISTER
12
2
SELF
REFRESH
A10
CONTROLLER
A11
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
BA0
BA1
DQML
DQMH
DATA IN
BUFFER
16
DQ 0-15
VDD/VDDQ
DATA OUT
BUFFER
Vss/VssQ
16
12
MULTIPLEXER
REFRESH
COUNTER
ROW
ADDRESS
LATCH
12
12
ROW
ADDRESS
BUFFER
ROW DECODER
CLK
CKE
CS
RAS
CAS
WE
4096
4096
4096
4096
MEMORY CELL
ARRAY
BANK 0
SENSE AMP I/O GATE
512
(x 16)
COLUMN
ADDRESS LATCH
BANK CONTROL LOGIC
9
BURST COUNTER
COLUMN DECODER
COLUMN
ADDRESS BUFFER
AS4SD8M16
2 March 27, 2015
Rev. 1.6
9
Micross Components reserves the right to change products or specifications without notice.
2
Integrated Silicon Solution, Inc. — www.issi.com
Rev. D
10/19/2011
SDRAM
AS4SD8M16
PIN DESCRIPTIONS
PIN NUMBER
38
37
SYMBOL
CLK
CKE
TYPE
DESCRIPTION
Input
Clock: CLK is driven by the system clock. All SDRAM input
signals are sampled on the positive edge of CLK. CLK also increments the
internal burst counter and controls the output registers.
Input
Clock Enable: CKE activates (HIGH) and deactivates (LOW) the
CLK signal. Deactivating the clock provides PRECHARGE POWER-DOWN
and SLEF REFRESH operation (all banks idle), ACTIVE POWER-DOWN
(row active in any bank) or CLOCK SUSPEND operation (burst/access in
progress). CKE is synchronous except after the device enters power-down
and self refresh modes, where CKE becomes asynchronous until after exiting
the same mode. The input buffers, including CLK, are disabled during powerdown and self refresh modes, providing low standby power. CKE may be tied
HIGH.
19
CS\
Input
Chip Select: CS\ enables (registered LOW) and disables
(registered HIGH) the command decoder. All commands are masked when
CS\ is registered HIGH. CS\ provides for external bank selection on systems
with multiple banks. CS\ in considered part of the command code.
16, 17, 18
WE\, CAS\,
RAS\
Input
Command Inputs: WE\, CAS\ and RAS\ (along with CS\) define
the command being entered.
15, 39
DQML, DQMU
Input
Input/Output Mask: DQM is an input mask signal for write
accesses and an output enable signal for read accesses. Input data is
masked when DWM is sampled HIGH during a WRITE cycle. The outptu
buffers are placed in a High-Z state (two-clock latency) when DQM is
sampled HIGH during a READ cycle. DQML corresponds to DQ0-DQ7 and
DQMH corresponds to
DQ8-DQ15. DQML and DQMH are considered same state when referenced
as DQM.
20, 21
BA0, BA1
Input
Bank Address Inputs: BA0 and BA1 define to which bank the
ACTIVE, READ, WRITE, or PRECHARGE command is being applied.
Address Inputs: A0-A11 are sampled during the ACTIVE
command (row address A0-A11) and READ/WRITE command (columnaddress A0-A8; with A10 defining auto precharge) to select one location out
of the memory array in the respective bank. A10 is sampled during a
PRECHARGE command to determine if all banks are to be prechaged (A10
[HIGH]) or bank selected by (A10 [LOW]). The address inputs also provide
the op-code during LOAD MODE REGISTER COMMAND.
23-26, 29-34, 22, 35
A0 - A11
Input
2, 4, 5, 7, 8, 10, 11, 13, 42,
44, 45, 47, 48, 50, 51, 53
DQ0 - DQ15
I/O
Data Input/Output: Data bus
40, 36
NC
---
No Connect: This pin should be left unconnected.
3, 9, 43, 49
VDDQ
Supply
DQ Power: Isolated DQ power to the die for improved noise
immunity.
6, 12, 46, 52
VSSQ
Supply
DQ Ground: Isolated DQ ground to the die for imporved noise
immunity.
1, 14, 27
VDD
Supply Power Supply: +3.3V ±0.3V
28, 41, 54
VSS
Supply Ground
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
3
SDRAM
AS4SD8M16
FUNCTIONAL DESCRIPTION
In general, the 128Mb SDRAMs are quad-bank DRAMs
that operate at 3.3V and include a synchronous interface (all
signals are registered on the positive edge of the clock signal,
CLK). Each of the 33,554,432-bit banks is organized as 4,096
rows by 512 columns by 16 bits.
Read and write accesses to the SDRAM are burst oriented; accesses start at a selected location and continue for a
programmed number of locations in a programmed sequence.
Accesses begin with the registration of an ACTIVE command,
which is then followed by a READ or WRITE command. The
address bits registered coincident with the ACTIVE command
are used to select the bank and row to be accessed (BA0 and
BA1 select the bank, A0 - A11 select the row). The address
bits (A0 - A8) registered coincident with the READ or WRITE
command are used to select the starting column location for the
burst access.
Prior to normal operation, the SDRAM must be initialized.
The following sections provide detailed information covering
device initialization, register definition, command descriptions
and device operation.
of operation of the SDRAM. This definition includes the
selection of a burst length, a burst type, a CAS latency, an
operating mode and a write burst mode, as shown in Figure
1. The mode register is programmed via the LOAD MODE
REGISTER command and will retain the stored information
until it is programmed again or the device loses power.
Mode register bits M0 - M2 specify the burst length, M3
specifies the type of burst (sequential or interleaved), M4 - M6
specify the CAS latency, M7 and M8 specify the operating
mode, M9 specifies the write burst mode, and M10 and M11
are reserved for future use.
The mode register must be loaded when all banks are
idle, and the controller must wait the specified time before
initiating the subsequent operation. Violating either of these
requirements will result in unspecified operation.
Burst Length
Read and write accesses to the SDRAM are burst oriented,
with the burst length being programmable, as shown in Figure 1. The burst length determines the maximum number of
column locations that can be accessed for a given READ or
WRITE command. Burst lengths of 1, 2, 4, or 8 locations are
available for both the sequential and the interleaved burst types,
and a full-page burst is available for the sequential types. The
full-page burst is used in conjunction with the BURST
TERMINATE command to generate arbitrary burst lengths.
Reserved states should not be used as unknown
operation or incompatibility with future versions may result.
When a READ or WRITE command is issued, a block of
columns equal to the burst length is effectively selected. All
accesses for that burst take place within this block, meaning that
the burst will wrap within the block if a boundary is reached.
The clock is uniquely selected by A1-A8 when the burst length
is set to two; by A2-A8 when the burst length is set to four, and
by A3-A8 when the burst length is set to eight. The remaining (least significant) address bit(s) is (are) used to select the
starting location within the block. Full-page bursts wrap within
the page if the boundary is reached.
Initialization
SDRAMs must be powered up and initialized in a predefined manner. Operational procedures other than those
specified may result in undefined operation. Once power is
applied to VDD and VDDQ (simultaneously) and the clock is
stable (stable clock is defined as a signal cycling within timing
constraints specified for the clock pin), the SDRAM requires a
100µs delay prior to issuing any command other than a COMMAND
INHIBIT or NOP. Starting at some point during
this 100µs period and continuing at least through the end of
this period, COMMAND INHIBIT or NOP commands should
be applied.
Once the 100µs delay has been satisfied with at least one
COMMAND INHIBIT or NOP command having been applied,
a PRECHARGE command should be applied. All banks must
then be precharged, thereby placing the device in the all banks
idle state.
Once in the idle state, two AUTO REFRESH cycles must
be preformed. After the AUTO REFRESH cycles are complete,
the SDRAM is ready for mode register programming. Because
the mode register will power up in an unknown state, it should
be loaded prior to applying any operational command.
Burst Type
Accesses within a given burst may be programmed to be
either sequential or interleaved; this is referred to as the burst
type and is selected via bit M3.
The ordering of accesses within a burst is determined
by the burst length, the burst type and the starting column
address, shown in table 1.
Register Definition
MODE REGISTER
The mode register is used to define the specific mode
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
4
SDRAM
AS4SD8M16
FIGURE 1: Mode Register Definition
TABLE 1: Burst Definition
BURST
LENGTH
2
4
8
Full
Page
(y)
STARTING
ORDER OF ACCESSES WITHIN A BURST
COLUMN TYPE = SEQUENTIAL TYPE = INTERLEAVED
A0
0
0-1
0-1
1
1-0
1-0
A1 A0
0 0
0-1-2-3
0-1-2-3
0 1
1-2-3-0
1-0-3-2
1 0
2-3-0-1
2-3-0-1
1 1
3-0-1-2
3-2-1-0
A2 A1 A0
0 0 0
0-1-2-3-4-5-6-7
0-1-2-3-4-5-6-7
0 0 1
1-2-3-4-5-6-7-0
1-0-3-2-5-4-7-6
0 1 0
2-3-4-5-6-7-0-12-3-0-1-6-7-4-5
0 1 1
3-4-5-6-7-0-1-2
3-2-1-0-7-6-5-4
1 0 0
4-5-6-7-0-1-2-3
4-5-6-7-0-1-2-3
1 0 1
5-6-7-0-1-2-3-4
5-4-7-6-1-0-3-2
1 1 0
6-7-0-1-2-3-4-5
6-7-4-5-2-3-0-1
1 1 1
7-0-1-2-3-4-5-6
7-6-5-4-3-2-1-0
Cn, Cn+1, Cn+2, Cn+3,
n=A0-A8
Cn+4…
Not Supported
(location 0-y)
…Cn-1,
Cn…
NOTES:
1. For full-page access: y=512
2. For a burst length of two, A1-A8 select the block-of-two burst;
A0 selects the starting column within the block.
3. For a burst length of four, A2-A8 select the block-of-four burst;
A0-A1 selects the starting column within the block.
4. For a burst length of eight, A3-A8 select the block-of-eight burst; A0-A2
selects the starting column within the block.
5. For a full-page burst, the full row is selected and A0-A8 select the starting
column.
6. Whenever a boundary of the block is reached within a given sequence
above, the following access wraps within the block.
7. For a burst length of one, A0-A8 select the unique column to be accessed,
and mode register bit M3 is ignored.
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
5
SDRAM
AS4SD8M16
CAS Latency
The CAS latency is the delay, in clock cycles, between
the registration of a READ command and the availability of
the first piece of output data. The latency can be set to two or
three clocks.
If a READ command is registered at clock edge n, and the
latency is m clocks, the data will be available by clock edge
n + m. The DQs will start driving as a result of the clock edge
one cycle earlier (n + m - 1), and provided that the relevant
access times are met, the data will be valid by clock edge n +
m. For example, assuming that the clock cycle time is such
that all relevant access times are met, if a READ command is
registered at T0 and the latency is programmed to two clocks,
the DQs will start driving after T1 and the data will be valid by
T2, as shown in Figure 2. Table 2 below indicates the operating
frequencies at which each CAS latency setting can be used.
Reserved states should not be used as unknown operation
or incompatibility with future versions may result.
Operating Mode
The normal operating mode is selected by setting M7 and
M8 to zero; the other combinations of values for M7 and M8
are reserved for future use and/or test modes. The programmed
burst length applies to both READ and WRITE bursts.
Test modes are reserved states should not be used because
unknown operation or incompatibility with future versions may
result.
FIGURE 2: CAS Latency
TABLE 2: CAS Latency
Write Burst Mode
When M9=0, the burst length programmed via M0-M2
applies to both READ and WRITE bursts; when M9=1, the
programmed burst length applies to READ bursts, but write
accesses are single-location (non-burst) accesses.
SPEED
-75
AS4SD8M16
Rev. 1.6 March 27, 2015
ALLOWABLE OPERATING
FREQUENCY (MHz)
CAS
CAS
LATENCY = 2
LATENCY = 3
<133
<100
Micross Components reserves the right to change products or specifications without notice.
6
SDRAM
AS4SD8M16
COMMANDS
ACTIVE
The ACTIVE command is used to open (or activate) a row
in a particular bank for a subsequent access. The value on the
BA0, BA1 inputs selects the bank, and the address provided
on inputs A0-A11 selects the row. The row remains active (or
open) for accesses until a PRECHARGE command is issued to
that bank. A PRECHARGE command must be issued before
opening a different row in the same bank.
Truth Table 1 provides a quick reference of available
commands. This is followed by a written description of each
command. Three additional Truth Tables appear following the
Operation section; these tables provide current state/next state
information.
COMMAND INHIBIT
The COMMAND INHIBIT function prevents new
commands from being executed by the SDRAM, regardless of
whether the CLK signal is enabled. The SDRAM is effectively
deselected. Operations already in progress are not affected.
READ
The READ command is used to initiate a burst read access
to an active row. The value on the BA0, BA1 inputs selects
the bank, and the address provided on inputs A0-A8 selects the
starting column location. The value on input A10 determines
whether or not auto precharge is used. If auto precharge is
selected, the row being accessed will be precharged at the end
of the READ burst; if auto precharge is not selected, the row
will remain open for subsequent accesses. Read data appears
on the DQs subject to the logic level on the DQM inputs two
clocks earlier. If a given DQM signal was registered HIGH,
the corresponding DQs will be High-Z two clocks later; if the
DQM signal was registered LOW, the DQs will provide valid
data.
NO OPERATION (NOP)
The NO OPERATION (NOP) command is used to perform a NOP to an SDRAM which is selected (CS\ is LOW).
This
prevents unwanted commands from being registered
during idle or wait states. Operations already in progress are
not affected.
LOAD MODE REGISTER
The mode register is loaded via inputs A0-A11. See mode
register heading in the Register Definition section. The LOAD
MODE REGISTER command can only be issued when all
banks are idle, and a subsequent executable command cannot be
issued until tMRD is met.
WRITE
The WRITE command is used to initiate a burst write
access to an active row. The value on the BA0, BA1 inputs
TRUTH TABLE 1: COMMANDS AND DQM OPERATION1
FUNCTION
COMMAND INHIBIT (NOP)
NO OPERATION (NOP)
ACTIVE (Select bank and activate row)
CS\ RAS\ CAS\ WE\
H
X
X
X
L
H
H
H
L
L
H
H
L
H
L
H
READ (Select bank and column, and start READ burst)
WRITE (Select bank and column, and start WRITE burst)
BURST TERMINATE
PRECHARGE (Deactivate row in bank or banks)
AUTO REFRESH or SELF REFRESH
(Enter self refresh mode)
LOAD MODE REGISTER
Write Enable/Output Enable
Write Inhibit/Output High-Z
DQM
ADDR
DQs NOTES
X
X
X
X
X
X
X
Bank/Row
X
3
8
Bank/Col
X
4
L/H
8
L
L
L
H
H
L
L
H
H
L
L
L
L/H
X
X
L
L
L
H
X
L
-
L
-
L
-
L
-
X
L
H
Bank/Col Valid
X
Active
Code
X
X
X
Op-Code
X
Active
High-Z
4
5
6, 7
2
8
8
NOTE:
1. CKE is HIGH for all commands shown except SELF REFRESH.
2. A0-A11 define the op-code written to the mode register.
3. A0-A11 provide row address, and BA0, BA1 determine which bank is made active.
4. A0-A8 provide column address; A10 HIGH enables the auto precharge feature (nonpersistent), while A10 LOW disables the auto precharge BA0, BA1 determine which bank is being read from or written to.
5. A10 LOW: BA0, BA1 determine the bank being precharged. A10 HIGH: All banks precharged and BA0, BA1 are “Don’t Care.”
6. This command is AUTO REFRESH if CKE is HIGH, SELF REFRESH if CKE is LOW.
7. Internal refresh counter controls row addressing; all inputs and I/Os are “Don’t Care” except for CKE.
8. Activates or deactivates the DQs during WRITEs (zero-clock delay) and READs (two-clock delay).
AS4SD8M16
Rev. 1.6 March 27, 2015
feature;
Micross Components reserves the right to change products or specifications without notice.
7
SDRAM
AS4SD8M16
TERMINATE command will be truncated, as shown in the
Operation section of this data sheet.
WRITE (continued)
selects the bank, and the address provided on inputs A0-A8
selects the starting column location. The value on input A10
determines whether or not auto precharge is used. If auto precharge is selected, the row being accessed will be precharged at
the end of the WRITE burst; if auto precharge is not selected,
the row will remain open for subsequent accesses. Input data
appearing on the DQs is written to the memory array subject to
the DQM input logic level appearing coincident with the data.
If a given DQM signal is registered LOW, the corresponding
data will be written to memory; if the DQM signal is registered
HIGH, the corresponding data inputs will be ignored, and a
WRITE will not be executed to that byte/column location.
AUTO REFRESH
AUTO REFRESH is used during normal operation of the
SDRAM and is analogous to CAS\-BEFORE-RAS\ (CBR)
REFRESH in conventional DRAMs. This command is nonpersistent, so it must be issued each time a refresh is required.
All active banks must be precharged prior to issuing an AUTO
REFRESH command. The AUTO REFRESH command
should not be issued until the minimum tRP has been met after
the PRECHARGE command as shown in the Operations section.
The addressing is generated by the internal refresh controller. This makes the address bits “Don’t Care” during an
AUTO REFRESH command. The 128Mb SDRAM requires
4,096 AUTO REFRESH cycles every 64ms (tREF), regardless
of width operation. Providing a distributed AUTO REFRESH
command every 15.625µs will meet the refresh requirement and
ensure that each row is refreshed. Alternatively, 4,096 AUTO
REFRESH commands can be issued in a burst at the minimum
cycle rate (tRFC), once every 64ms (24ms for XT version).
PRECHARGE
The PRECHARGE command is used to deactivate the open
row in a particular bank or the open row in all banks. The
bank(s) will be available for a subsequent row access a
specified time (tRP) after the PRECHARGE command is issued.
Input A10 determines whether one or all banks are to be precharged, an in the case where only one bank is to be precharged,
inputs BA0, BA1 select the bank. Otherwise BA0, BA1 are
treated as “Don’t Care.” Once a bank has been precharged, it
is in the idle state and must be activated prior to any READ or
WRITE commands being issued to that bank.
SELF REFRESH (IT & ET Temp options ONLY)
The SELF REFRESH command can be used to retain
data in the SDRAM, even if the rest of the system is powered
down. When in the self refresh mode, the SDRAM retains data
without external clocking. The SELF REFRESH command is
initiated like and AUTO REFRESH command except CKE
is disabled (LOW). Once the SELF REFRESH command is
registered, all the inputs to the SDRAM become “Don’t Care”
with the exception of CKE, which must remain LOW.
Once self refresh mode is engaged, the SDRAM provides
its own internal clocking, causing it to perform its own AUTO
REFRESH cycles. The SDRAM must remain in self refresh
mode for a minimum period equal to tRAS and may remain in
self refresh mode for an indefinite period beyond that.
The procedure for exiting self refresh requires a sequence
of commands. First, CLK must be stable (stable clock is defined as a signal cycling within timing constraints specified
for the clock pin) prior to CKE going back HIGH. Once CKE
is HIGH, the SDRAM must have NOP commands issued (a
minimum of two clocks) for tXSR because time is required for
the completion of any internal refresh in progress.
Upon exiting the self refresh mode, AUTO REFRESH
commands must be issued every 15.625µs or less as both
SELF REFRESH and AUTO REFRESH utilize the row refresh
counter. The SELF REFRESH and AUTO REFRESH option
are available with the IT and ET temperature options. They
are not available with the XT temperature options.
AUTO PRECHARGE
Auto precharge is a feature which performs the same individual-bank PRECHARGE functions described above, without
requiring an explicit command. This is accomplished by using
A10 to enable auto precharge in conjunction with a specific
READ or WRITE command. A PRECHARGE of the bank/
row that is addressed with the READ or WRITE command
is automatically performed upon completion of the READ or
WRITE burst, except in the full-page burst mode, where AUTO
PRECHARGE does not apply. Auto precharge is nonpersistent
in that it is either enabled or disabled for each individual READ
or WRITE command.
Auto precharge ensures that the precharge is initiated at
the earliest valid stage within a burst. The user must not issue
another command to the same bank until the precharge time
(tRP) is completed. This is determined as if an explicit PRECHARGE command was issued at the earliest possible time,
as described for each burst type in the Operation section of this
data sheet.
BURST TERMINATE
The BURST TERMINATE command is used to truncate
either fixed-length or full-page bursts. The most recently
registered READ or WRITE command prior to the BURST
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
8
SDRAM
AS4SD8M16
FIGURE 3: Activating a Specific Row
in a Specific Bank
OPERATION
BANK/ROW ACTIVATION
Before any READ or WRITE commands can be issued to a
bank within the SDRAM, a row in that bank must be “opened.”
This is accomplished via the ACTIVE command, which selects
both the bank and the row to be activated (see Figure 3).
After opening a row (issuing an ACTIVE command), a
READ or WRITE command may be issued to that row, subject to the tRCD specification. tRCD (MIN) should be divided
by the clock period and rounded up to the next whole number
to determine the earliest clock edge after the ACTIVE command on which a READ or WRITE command can be entered.
For example, a tRCD specification of 20ns with a 125 MHz
clock (8ns period) results in 2.5 clocks, rounded to 3. This is
reflected in Figure 4, which covers any case where 2 < tRCD
(MIN)/
tCK < 3. (The same procedure is used to convert
other specification limits from time units to clock cycles.)
A subsequent ACTIVE command to a different row in the
same bank can only be issued after the previous active row
has been “closed” (precharged). The minimum time interval
between successive ACTIVE commands to the same bank is
defined by tRC.
A subsequent ACTIVE command to another bank can be
issued while the first bank is being accessed, which results in
a reduction of total row-access overhead. The minimum time
interval between successive ACTIVE commands to different
banks is defined by tRRD.
FIGURE 4: Example - Meeting tRCD (MIN) When 2 < tRCD (MIN)/ tCK < 3
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
9
SDRAM
AS4SD8M16
READs
READ bursts are initiated with a READ command, as
shown in Figure 5.
The starting column and bank addresses are provided with
the READ command, and auto precharge is either enabled or
disabled for that burst access. If auto precharge is enabled,
the row being accessed is precharged at the completion of the
burst. For the generic READ commands used in the following
illustrations, auto precharge is disabled.
During READ bursts, the valid data-out element from the
starting column address will be available following the CAS
latency after the READ command. Each subsequent data-out
element will be valid by the next positive clock edge. Figure 6
shows general timing for each possible CAS latency setting.
Upon completion of a burst, assuming no other commands
have been initiated, the DQs will go High-Z. A full-page burst
will continue until terminated. (At the end of the page, it will
wrap to the start address and continue.)
Data from any READ burst may be truncated with a
subsequent READ command, and data from a fixed-length
READ burst may be immediately followed by data from a
READ command. In either case, a continuous flow of data
can be maintained. The first data element from the new burst
follows either the last element of a complete burst or the last
desired data element of a longer burst that is being truncated.
The new READ command should be issued x cycles before
the clock edge at which the last desired data element is valid,
where x equals the CAS latency minus one. This is shown in
Figure 7 for CAS latencies of two and three; data element n+3
is either the last of a burst of four or the last desired of a longer
burst. The 128Mb SDRAM uses a pipelined architecture and
therefore does not require the 2n rule associated with a prefetch
architecture. A READ command can be initiated on any clock
cycle following a previous READ command. Full-speed
random read accesses can be performed to the same bank,
as shown in Figure 8, or each subsequent READ may be
performed to different bank.
FIGURE 5: READ Command
FIGURE 6: CAS Latency
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
10
SDRAM
AS4SD8M16
FIGURE 7: Consecutive READ Bursts
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
11
SDRAM
AS4SD8M16
FIGURE 8: Random READ Accesses
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
12
SDRAM
AS4SD8M16
Data from any READ burst may be truncated with a
subsequent WRITE command, and data from a fixed-length
READ burst may be immediately followed by data from a
WRITE command (subject to bus turn-around limitations).
The WRITE burst may be initiated on the clock edge immediately following the last (or last desired) data element from
the READ burst, provided that I/O contention can be avoided.
In a given
system design, there may be a possibility that
the device
driving the input data will go Low-Z before the
SDRAM DQs go High-Z. In this case, at least a single-cycle
delay should occur between the last read data and the WRITE
command.
The DQM input is used to avoid I/O contention, as shown
in Figures 9 and 10. The DQM signal must be asserted (HIGH)
at least two clocks prior to the write command (DQM latency
is two clocks for output buffers) to suppress data-out from the
READ. Once the WRITE command is registered, the DQs
will go High-Z (or remain High-Z), regardless of the state of
the DQM signal; provided the DQM was active on the clock
just prior to the WRITE command that truncated the READ
command. If not, the second WRITE will be an invalid WRITE.
For example, if DQM was LOW during T4 in Figure 10, the
WRITEs at T5 and T7 would be valid, while the WRITE at T6
would be invalid.
The DQM signal must be de-asserted prior to the WRITE
command (DQM latency is zero clocks for input buffers) to
ensure that the written data is not masked. Figure 9 shows the
case where the clock frequency allows for bus contention to
be avoided without adding a NOP cycle, and Figure 10 shows
the case where the additional NOP is needed.
A fixed-length READ burst may be followed by, or truncat-
ed with, a PRECHARGE command to the same bank (provided
that auto precharge was not activated), and a full-page burst may
be truncated with a PRECHARGE command to the same bank.
The PRECHARGE command should be issued x cycles before
the clock edge at which the last desired data element is valid,
where x equals the CAS latency minus one. This is shown in
Figure 11 for each possible CAS latency; data element n+3 is
either the last of a burst of four or the last desired of a longer
burst. Following the PRECHARGE command, a subsequent
command to the same bank cannot be issued until tRP is met.
Note that part of the row precharge time is hidden during the
access of the last data element(s).
In the case of a fixed-length burst being executed to completion, a PRECHARGE command issued at the optimum time
(as described above) provides the same operation that would
result from the same fixed-length burst with auto precharge.
The disadvantage of the PRECHARGE command is that it
requires that the command and address buses be
available
at the appropriate time to issue the command; the advantage of
the PRECHARGE command is that it can be used to truncate
fixed-length or full-page bursts.
Full-page READ bursts can be truncated with the BURST
TERMINATE command, and fixed-length READ bursts may
be truncated with a BURST TERMINATE command, provided
that auto precharge was not activated. The BURST TERMINATE command should be issued x cycles before the clock
edge at which the last desired data element is valid, where x
equals the CAS latency minus one. This is shown in Figure
12 for each possible CAS latency; data element n+3 is the last
desired data element of a longer burst.
FIGURE 9: READ to WRITE
FIGURE 10: READ to WRITE With
Extra Clock Cycle
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
13
SDRAM
AS4SD8M16
FIGURE 11: READ to PRECHARGE
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
14
SDRAM
AS4SD8M16
FIGURE 12: Terminating a READ Burst
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
15
SDRAM
AS4SD8M16
WRITEs
WRITE bursts are initiated with a WRITE command, as
shown in Figure 13.
The starting column and blank addresses are provided with
the WRITE command, an auto precharge is either enabled or
disabled for that access. If auto precharge is enabled, the row
being accessed is precharged at the completion of the burst.
For the generic WRITE commands used in the following illustrations, auto precharge is disabled.
During WRITE bursts, the first valid data-in element will be
registered coincident with the WRITE command. Subsequent
data elements will be registered on each successive positive
clock edge. Upon completion of a fixed-length burst, assuming no other commands have been initiated, the DQs will be
ignored (see Figure 14). A full-page burst will continue until
terminated. (At the end of the page, it will wrap to the start
address and continue.)
Data for any WRITE burst may be truncated with a
subsequent WRITE command, and data for a fixed-length
WRITE burst may be immediately followed by data for a
WRITE command. The new WRITE command can be issued
on any clock following the previous WRITE command, and the
data provided coincident with the new command applies to the
new command. An example is shown in Figure 15. Data n+1
is either the last of a burst of two or the last desired of a longer
burst. The 128Mb SDRAM uses a pipelined architecture and
therefore does not require the 2n rule associated with a prefetch
architecture. A WRITE command can be initiated on any clock
cycle following a previous WRITE command. Full-speed
random write accesses within a page can be performed to the
same bank, as shown in Figure 16, or each subsequent WRITE
may be preformed to a different bank.
FIGURE 14: WRITE Burst
FIGURE 13: WRITE Command
FIGURE 15: WRITE to WRITE
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
16
SDRAM
AS4SD8M16
Data for any WRITE burst may be truncated with a subsequent READ command, and data for a fixed-length WRITE
burst may be immediately followed by a READ command.
Once the READ command is registered, the data inputs will
be ignored, and WRITEs will not be executed. An example is
shown in Figure 17. Data n+1 is either the last of a burst of
two or the last desired of a longer burst.
Data for a fixed-length WRITE burst may be followed by,
or truncated with, a PRECHARGE command to the same bank
(provided that auto precharge was not activated), and a full-page
WRITE burst may be truncated with a PRECHARGE command
to the same bank. The PRECHARGE command should be
issued tWR after the clock edge at which the last desired input
data element is registered. The auto precharge mode requires
a tWR of at least one clock plus time, regardless of frequency.
In addition, when truncating a WRITE burst, the DQM signal
must be used to mask input data for the clock edge prior to, and
the clock edge coincident with, the PRECHARGE command.
An example is shown in Figure 18. Data n+1 is either the last
of a burst of two or the last desired of a longer burst. Following
the PRECHARGE command, a subsequent command to the
same bank cannot be issued until tRP is met. The precharge
can be issued coincident with the first coincident clock edge
(T2 in Figure 18) on an A1 Version and with the second clock
on an A2 Version (Figure 18).
In the case of a fixed-length burst being executed to completion, a PRECHARGE command issued at the optimum time
(as described above) provides the same operation that would
result from the same fixed-length burst with auto precharge.
The disadvantage of the PRECHARGE command is that is
requires that the command and address buses be
available
at the appropriate time to issue the command; the advantage of
the PRECHARGE command is that it can be used to truncate
fixed-length or full-page bursts.
FIGURE 16: Random WRITE Cycles
FIGURE 18: WRITE to PRECHARGE
FIGURE 17: WRITE to READ
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
17
SDRAM
AS4SD8M16
Fixed-length or full-page WRITE bursts can be truncated
with the BURST TERMINATE command. When truncate a
WRITE burst, the input data applied coincident with the BURST
TERMINATE command will be ignored. The last data written (provided that DQM is LOW at that time) will be the input
data applied one clock previous to the BURST TERMINATE
command. This is shown in Figure 19, where data n is the last
desired data element of a longer burst.
PRECHARGE
The PRECHARGE command (see Figure 20) is used to
deactivate the open row in a particular bank or the open row
in all banks. The bank(s) will be available for a subsequent
row access some specified time (tRP) after the PRECHARGE
command is issued. Input A10 determines whether one or all
banks are to be precharged, and in the case where only one bank
is to be precharged, inputs BA0, BA1 select the bank. When
all banks are to be precharged, inputs BA0, BA1 are treated as
“Don’t Care”. Once a bank has been precharged, it is in the
idle state and must be activated prior to any READ or WRITE
commands being issued to that bank.
POWER-DOWN
Power-down occurs if CKE is registered LOW coincident
with a NOP or COMMAND INHIBIT when no accesses are
in progress. If power-down occurs when all banks are idle,
this mode is referred to as precharge power-down; if powerdown occurs when there is a row active in any bank, this mode
is referred to as active power-down. Entering power-down
deactivates the input and output buffers, excluding CKE, for
maximum power saving while in standby. The device may
not remain in the power-down state longer then the refresh
period (64ms) since no refresh operations are performed in this
mode.
The power-down state is exited by registering a NOP or
COMMAND INHIBIT and CKE HIGH at the desired clock
edge (meeting tCKS). See Figure 21.
FIGURE 20: PRECHARGE Command
FIGURE 19: Terminating a WRITE
Burst
FIGURE 21: Power-Down
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
18
SDRAM
AS4SD8M16
CLOCK SUSPEND
The clock suspend mode occurs when a column access/
burst is in progress and CKE is registered LOW. In the clock
suspend mode, the internal clock is deactivated, “freezing” the
synchronous logic.
For each positive clock edge on which CKE is sampled
LOW, the next internal positive clock edge is suspended. Any
command or data present on the input pins at the time of a
suspected internal clock edge is ignored; any data present on
the DQ pins remains driven; and burst counters are not incremented, as long as the clock is suspended. (See examples in
Figure 22 and 23).
Clock suspend more is exited by registering CKE HIGH;
the internal clock and related operation will resume on the
subsequent positive clock edge.
BURST READ/SINGLE WRITE
The burst read/single write mode is entered by programming the write burst mode bit (M9) in the mode register to a
logic 1. In this mode, all WRITE commands result in the access
of a single column location (burst of one), regardless of the
programmed burst length. READ commands access columns
according to the programmed burst length and sequence, just
as in the normal mode of operation (M9 = 0).
FIGURE 22: Clock Suspend During WRITE Burst
FIGURE 23: Clock Suspend During READ Burst
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
19
SDRAM
AS4SD8M16
CONCURRENT AUTO PRECHARGE
An access command (READ or WRITE) to another bank
while an access command with auto precharge enabled is
executing is not allowed by SDRAMs, unless the SDRAM
supports CONCURRENT AUTO PRECHARGE. Micross
SDRAMs support CONCURRENT AUTO PRECHARGE.
Four cases where CONCURRENT AUTO PRECHARGE occurs are defined below.
READ with Auto Precharge
1. Interrupted by a READ (with or without auto precharge);
A READ to bank m will interrupt a READ on bank n, CAS
latency later. The PRECHARGE to bank n will begin when
the READ to bank m is registered (Figure 24).
2. Interrupted by a WRITE (with or without auto precharge):
A WRITE to bank m will interrupt a READ on bank n when
registered. DQM should be used two clocks prior to the WRITE
command to prevent bus contention. The PRECHARGE to
bank n will begin when the WRITE to bank m is registered
(Figure 25).
FIGURE 24: READ With Auto Precharge Interrupted by a READ
FIGURE 25: READ With Auto Precharge Interrupted by a WRITE
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
20
SDRAM
AS4SD8M16
WRITE with Auto Precharge
3. Interrupted by a READ (with or without auto precharge);
A READ to bank m will interrupt a WRITE on bank n when
registered, with the data-out appearing CAS latency later. The
PRECHARGE to bank n will begin after tWR is met, where tWR
begins when the READ to bank m is registered. The last valid
WRITE to bank n will be data-in registered one clock prior to
the READ to bank m (Figure 26).
4. Interrupted by a WRITE (with or without auto precharge):
A WRITE to bank m will interrupt a WRITE on bank n when
registered. The PRECHARGE to bank n will begin after tWR is
met, where tWR begins when the WRITE to bank m is registered.
The last valid data WRITE to bank n will be data registered one
clock prior to the WRITE to bank m (Figure 26).
FIGURE 26: WRITE With Auto Precharge Interrupted by a READ
FIGURE 27: WRITE With Auto Precharge Interrupted by a WRITE
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
21
SDRAM
AS4SD8M16
TRUTH TABLE 2: CKE1,2,3,4
CKEn-1 CKEn
L
L
L
H
H
L
H
H
CURRENT STATE
Power-Down
Self Refresh
Clock Suspend
Power-Down
Self Refresh
Clock Suspend
All Banks Idle
All Banks Idle
Reading or Writing
COMMANDn
X
X
X
COMMAND INHIBIT or NOP
COMMAND INHIBIT or NOP
X
COMMAND INHIBIT or NOP
AUTO REFRESH
VALID
See Truth Table 3
ACTIONn
Maintain Power-Down
Maintain Self Refresh
Maintain Clock Suspend
Exit Power-Down
Exit Self Refresh
Exit Clock Suspend
Power-Down Entry
Self Refresh Entry
Clock Suspend Entry
NOTES
5
6
7
NOTES:
1. CKEn is the logic state of CKE at clock edge n; CKEn-1 was the state of CKE at the previous clock edge.
2. Current state is the state of the SDRAM immediately prior to clock edge n.
3. COMMANDn is the command registered at clock edge n, and ACTIONn is a result of COMMANDn.
4. All states and sequences not shown are illegal or reserved.
5. Exiting power-down at clock edge n will put the device in the all banks idle state in time for clock edge n+1 (provided
that tCKS is met).
6. Exiting self refresh at clock edge n will put the device in the all banks idle state once tXSR is met. COMMAND INHIBIT or
NOP commands should be issued on any clock edges occurring during the tXSR period. A minimum of two NOP commands
must be provided during tXSR period.
7. After exiting clock suspend at clock edge n, the device will resume operation and recognize the next command at clock
edge n+1.
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
22
SDRAM
AS4SD8M16
TRUTH TABLE 3: CURRENT STATE BANK n, COMMAND TO BANK n1,2,3,4,5,6
CURRENT STATE CS\ RAS\ CAS\ WE\
COMMAND (ACTION)
H
X
X
X COMMAND INHIBIT (NOP/Continue previous operation)
ANY
L
H
H
H NO OPERATION (NOP/Continue previous operation)
L
L
H
H ACTIVE (Select and active row)
L
L
L
H AUTO REFRESH
Idle
L
L
L
L LOAD MODE REGISTER
L
L
H
L PRECHARGE
L
H
L
H READ (Select column and start READ burst)
Row Active
L
H
L
L WRITE (Select column and start WRITE burst)
L
L
H
L PRECHARGE (Deactivate row in bank or banks)
L
H
L
H READ (Select column and start new READ burst)
Read
L
H
L
L WRITE (Select column and start WRITE burst)
(Auto Precharge
L
L
H
L PRECHARGE (Truncate READ burst, start PRECHARGE)
Disabled)
L
H
H
L BURST TERMINATE
L
H
L
H READ (Select column and start READ burst)
Write
L
H
L
L WRITE (Select column and start new WRITE burst)
(Auto Precharge
L
L
H
L PRECHARGE (Truncate WRITE burst, start PRECHARGE)
Disabled)
L
H
H
L BURST TERMINATE
NOTES
7
7
11
10
10
8
10
10
8
9
10
10
8
9
NOTES:
1. This table applies when CKEn-1 was HIGH and CKEn is HIGH (see Truth Table 2) and after tXSR has been met (if the previous
state was self refresh).
2. This table is bank-specific, except where noted, i.e., the current state is for a specific bank and the commands shown are those
allowed to be issued to that bank when in that state. Exceptions are covered in the notes below.
3. Current state definitions:
Idle:
The bank has been precharged, and tRP has been met.
Row Active: A row in the bank has been activated, and tRCD has been met. No data bursts/accesses and no
register accesses are in progress.
Read: A READ burst has been initiated, with auto precharge disabled, and has not yet terminated or been
terminated.
Write: A WRITE burst has been initiated, with auto precharge disabled, and has not yet terminated or been
terminated.
4. The following states must not be interrupted by a command issued to the same bank. COMMAND INHIBIT or NOP commands,
or allowable commands to the other bank should be issued on any clock edge occurring during these states. Allowable commands
to the other bank are determined by its current state and Truth Table 3, and according to Truth Table 4.
Precharging:
Starts with registration of a PRECHARGE command and ends when tRP is met. Once tRP is met, the
bank will be in the idle state.
Row Activating: Starts with registration of an ACTIVE command and ends when tRCD is met. Once tRCD is met, the
bank will be in the row active state.
Read w/ Auto
Precharge Enabled:
Starts with registration of a READ command with auto precharge enabled and ends when tRP has
been met. Once tRP is met, the bank will be in the idle state.
Write w/ Auto
Precharge Enabled:
Starts with registration of a WRITE command with auto precharge enabled and ends when tRP has
been met. Once tRP is met, the bank will be in the idle state.
(continued on next page)
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
23
SDRAM
AS4SD8M16
NOTES (continued):
5. The following states must not be interrupted by any executable command; COMMAND INHIBIT or NOP commands must be
applied on each positive clock edge during these states.
Refreshing: Starts with registration of an AUTO REFRESH command and ends when tRC is met. Once tRC is met,
the SDRAM will be in the all banks idle state.
Accessing Mode
Register: Starts with registration of a LOAD MODE REGISTER command and ends when tMRD has been met.
Once tMRD is met, the SDRAM will be in the all banks idle state.
Precharging All: States with registration of a PRECHARGE ALL command and ends when tRP is met. Once tRP is met,
all banks will be in the idle state.
6. All states and sequences not shown are illegal or reserved.
7. Not bank-specific; requires that all banks are idle.
8. May or may not be bank-specific; if all banks are to be precharged, all must be in valid state for precharging.
9. Not bank-specific; BURST TERMINATE affects the most recent READ or WRITE burst, regardless of bank.
10. READs or WRITEs listed in the Command column include READs or WRITEs with auto precharge enabled and READs or
WRITEs with auto precharge disabled.
11. Does not affect the state of the bank and acts as a NOP to that bank.
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
24
SDRAM
AS4SD8M16
TRUTH TABLE 4: CURRENT STATE BANK n, COMMAND TO BANK m1,2,3,4,5,6
CURRENT STATE CS\ RAS\ CAS\ WE\
COMMAND (ACTION)
H
X
X
X COMMAND INHIBIT (NOP/Continue previous operation)
Any
L
H
H
H NO OPERATION (NOP/Continue previous operation)
Idle
X
X
X
X Any Command Otherwise Allowed to Bank m
L
L
H
H ACTIVE (Select and active row)
Row Activating,
L
H
L
H READ (Select column and start READ burst)
Active, or
L
H
L
L WRITE (Select column and start WRITE burst)
Precharging
L
L
H
L PRECHARGE
L
L
H
H ACTIVE (Select and active row)
Read
L
H
L
H READ (Select column and start new READ burst)
(Auto Precharge
L
H
L
L WRITE (Select column and start WRITE burst)
Disabled)
L
L
H
L PRECHARGE
L
L
H
H ACTIVE (Select and active row)
Write
L
H
L
H READ (Select column and start READ burst)
(Auto Precharge
L
H
L
L WRITE (Select column and start new WRITE burst)
Disabled)
L
L
H
L PRECHARGE
L
L
H
H ACTIVE (Select and active row)
Read
L
H
L
H READ (Select column and start new READ burst)
(with Auto
L
H
L
L WRITE (Select column and start WRITE burst)
Precharge)
L
L
H
L PRECHARGE
L
L
H
H ACTIVE (Select and active row)
Write
L
H
L
H READ (Select column and start READ burst)
(with Auto
L
H
L
L WRITE (Select column and start new WRITE burst)
Precharge)
L
L
H
L PRECHARGE
NOTES
7
7
7, 10
7, 11
9
7, 12
7, 13
9
7, 8, 14
7, 8, 15
9
7, 8, 16
7, 8, 17
9
NOTES:
1. This table applies when CKEn-1 was HIGH and CKEn is HIGH (see Truth Table 2) and after tXSR has been met (if the previous state
was self refresh).
2. This table describes alternate bank operation, except where noted; i.e., the current state is for bank n and the commands shown are
those allowed to be issued to bank m (assuming bank m is in such a state that the given command is allowable). Exceptions are covered
in the notes below.
3. Current state definitions:
Idle:
The bank has been precharged, and tRP has been met.
Row Active: A row in the bank has been activated, and tRCD has been met. No data bursts/accesses and no
register accesses are in progress.
Read: A READ burst has been initiated, with auto precharge disabled, and has not yet terminated or been
terminated.
Write: A WRITE burst has been initiated, with auto precharge disabled, and has not yet terminated or been
terminated.
Read w/ Auto
Precharge Enabled:
Starts with registration of a READ command with auto precharge enabled and ends when tRP has
been met. Once tRP is met, the bank will be in the idle state.
Write w/ Auto
Precharge Enabled:
Starts with registration of a WRITE command with auto precharge enabled and ends when tRP has
been met. Once tRP is met, the bank will be in the idle state.
4. AUTO REFRESH, SELF REFRESH and LOAD MODE REGISTER commands may only be issued when all banks are idle.
5. A BURST TERMINATE command cannot be issued to another bank; it applies to the bank represented by the current state only.
6. All states and sequences not shown are illegal or reserved.
(continued on next page)
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
25
SDRAM
AS4SD8M16
NOTES (continued):
5. A BURST TERMINATE command cannot be issued to another bank; it applies to the bank represented by the current state
only.
6. All states and sequences not shown are illegal or reserved.
7. READs or WRITEs to bank m listed in the Command column include READs or WRITEs with auto precharge enabled and
READs or WRITEs with auto precharge disabled.
8. CONCURRENT AUTO PRECHARGE: bank n will initiate the auto precharge command when its burst has been interrupted
by bank m’s burst.
9. Burst in bank n continues as initiated.
10. For a READ without auto precharge interrupted by a READ (with or without auto precharge), the READ to bank m will
interrupt the READ on bank n, CAS latency later (Figure 7).
11. For a READ without auto precharge interrupted by a WRITE (with or without auto precharge), the WRITE to bank m will
interrupt the READ on bank n when registered (Figures 9 and 10). DQM should be used one clock prior to the WRITE command to prevent bus contention.
12. For a WRITE without auto precharge interrupted by a READ (with or without auto precharge), the READ to bank m will
interrupt the WRITE on bank n when registered (Figure 17), with the data-out appearing CAS latency later. The last valid
WRITE to bank n will be data-in registered one clock prior to the READ on bank m.
13. For a WRITE without auto precharge interrupted by a WRITE (with or without auto precharge), the WRITE to bank m will
interrupt the WRITE on bank n when registered (Figure 15). The last valid WRITE to bank n will be data-in registered one
clock prior to the READ to bank m.
14. For a READ with auto precharge interrupted by a READ (with or without auto precharge), the READ to bank m will interrupt the READ on bank n, CAS latency later. The PRECHARGE to bank n will begin when the READ to bank m is registered
(Figure 25).
15. For a READ with auto precharge interrupted by a WRITE (with or without auto precharge), the WRITE to bank m will
interrupt the READ on bank n when registered. DQM should be used two clocks prior to the WRITE command to prevent bus
contention. The PRECHARGE to bank n will begin when the WRITE to bank m is registered (Figure 25).
16. For a WRITE with auto precharge interrupted by a READ (with or without auto precharge), the READ to bank m will
interrupt the WRITE on bank n when registered, with the data-out appearing CAS latency later. The PRECHARGE to bank n
will begin after tWR is met, where tWR begins when the READ to bank m is registered. The last valid WRITE to bank n will be
data-in registered one clock prior to the READ to bank m (Figure 26).
17. For a WRITE with auto precharge interrupted by a WRITE (with or without auto precharge), the WRITE to bank m will
interrupt the WRITE on bank n when registered. The PRECHARGE to bank n will begin after tWR is met, where tWR begins
when the WRITE to bank m is registered. The last valid WRITE to bank n will be data registered one clock prior to the WRITE
to bank m (Figure 27).
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
26
SDRAM
AS4SD8M16
ABSOLUTE MAXIMUM RATINGS*
Voltage on VDD, VDDQ Supply
Relative to VSS...........................................-0.5V to +4.6V
Voltage on Inputs, NC or I/O Pins
Relative to VSS...........................................-0.5V to +4.6V
Operating Temperature, TA (IT)......................-40°C to +85°C
Operating Temperature, TA (ET)....................-40°C to +105°C
Operating Temperature, TA (XT)...................-55°C to +125°C
Storage Temperature (plastic).......................-55°C to +150°C
Power Dissipation..............................................................1W
*Stresses greater than those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device. This
is a stress rating only and functional operation of the device
at these or any other conditions above those indicated in the
operation section of this specification is not implied. Exposure
to absolute maximum rating conditions for extended periods
may affect reliability.
**Junction temperature depends upon package type, cycle
time, loading, ambient temperature and airflow, and humidity
(plastics).
ELECTRICAL CHARACTERISTICS AND RECOMMENDED DC OPERATING CONDITIONS1,5,6
(VDD, VDDQ = +3.3V ±0.3V)
PARAMETER
SYMBOL
MIN
MAX
UNITS
VDD, VDDQ
3
3.6
V
Input High Voltage: Logic 1; All inputs
VIH
2.2
VDD+ 0.3
V
22
Input Low Voltage: Logic 0; All inputs
VIL
-0.3
0.8
V
22
II
-5
5
µA
IOZ
-5
5
µA
Output Levels:
Output High Voltage (IOUT = -4mA)
VOH
2.4
---
V
Output Low Voltage (IOUT = 4mA)
VOL
---
0.4
V
Supply Voltage
Input Leakage Current: Any input 0V < VIN < VDD
(All other pins not under test = 0V)
Output Leakage Current: DQs are disabled:
0V < VOUT < VDDQ
NOTES
IDD SPECIFICATIONS AND CONDITIONS1,5,6,11,13 (VDD, VDDQ = +3.3V ±0.3V)
SYMBOL MAX (-75)
PARAMETER
Operating Current: Active Mode;
Burst = 2; READ or WRITE; t RC = tRC (MIN)
UNITS
NOTES
IDD1
150
mA
3, 18,
19, 32
Standby Current: Power-Down Mode;
All banks idle; CKE = LOW
IDD2
2
mA
32
Standby Current: Active Mode;
CKE = HIGH; CS\ = HIGH; All banks active after tRCD met;
No accesses in progress
IDD3
50
mA
3, 12,
19, 32
Operating Current: Burst Mode; Continuous Burst;
READ or WRITE: All banks active
IDD4
150
mA
3, 18,
19, 32
tRFC = tRFC (MIN)
IDD5
310
mA
tRFC = 7.81 µs
IDD6
3
mA
3, 12,
18, 19,
32, 33
IDD7
2
mA
4, 35
Auto Refresh Current
CS\ = HIGH; CKE = HIGH
SELF REFRESH CURRENT: CKE < 0.2V
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
27
SDRAM
AS4SD8M16
CAPACITANCE2
PARAMETER
SYM
MIN
MAX
UNITS
NOTES
Input Capacitance: CLK
CI1
2
3.5
pF
29
Input Capacitance: All other input-only pins
CI2
2
3.5
pF
30
Input/Output Capacitance: DQs
CIO
4.0
6.0
pF
31
AC FUNCTIONAL CHARACTERISTICS5,6,7,8,9,11
SYMBOL
-75
UNITS
NOTES
READ/WRITE command to READ/WRITE command
tCCD
1
tCK
17
CKE to clock disable or power-down entry mode
tCKED
1
tCK
14
CKE to clock enable or power-down exit setup mode
tPED
1
tCK
14
DQM to input data delay
tDQD
0
tCK
17
DQM to data mask during WRITEs
tDQM
0
tCK
17
DQM to data high-impedance during READs
tDQZ
2
tCK
17
WRITE command to input data delay
tDWD
0
tCK
17
Data-in to ACTIVE command
tDAL
5
tCK
15, 21
Data-in to PRECHARGE command
tDPL
2
tCK
16, 21
Last data-in to burst STOP command
tBDL
1
tCK
17
Last data-in to new READ/WRITE command
tCDL
1
tCK
17
Last data-in to PRECHARGE command
tRDL
2
tCK
16, 21
LOAD MODE REGISTER command to ACTIVE or REFRESH command
tMRD
2
tCK
26
CL = 3
tROH(3)
3
tCK
17
CL = 2
tROH(2)
2
tCK
17
PARAMETER
Data-out to high-impedance from PRECHARGE command
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
28
SDRAM
AS4SD8M16
ELECTRICAL CHARACTERISTICS AND RECOMMENDED AC OPERATING
CONDITIONS5,6,8,9,11
PARAMETER
Access time from CLK (pos. edge)
SYM
MIN
-75
MAX
UNITS
NOTES
27
CL = 3
tAC(3)
5.4
ns
CL = 2
tAC(2)
6
ns
Address hold time
tAH
0.8
ns
Address setup time
tAS
1.5
ns
CLK high-level width
tCH
2.5
ns
CLK low-level width
tCL
2.5
ns
CL = 3
tCK(3)
7.5
ns
23
CL = 2
tCK(2)
10
ns
23
CKE hold time
tCKH
0.8
ns
CKE setup time
tCKS
1.5
ns
CS\, RAS\, CAS\, WE\, DQM hold time
tCMH
0.8
ns
CS\, RAS\, CAS\, WE\, DQM setup time
tCMS
1.5
ns
Data-in hold time
tDH
0.8
ns
Data-in setup time
tDS
1.5
ns
Clock cycle time
Data-out high-impedance time
CL = 3
tHZ(3)
5.4
ns
10
CL = 2
tHZ(2)
6
ns
10
Data-out low-impedance time
tLZ
1
ns
Data-out hold time (load)
tOH
3
ns
Data-out hold time (no load)
tOHN
1.8
ns
ACTIVE to PRECHARGE command
tRAS
44
ACTIVE to ACTIVE command
tRC
66
ns
ACTIVE to READ or WRITE delay
tRCD
20
ns
Refresh period (4,096 rows)
tREF
AUTO REFRESH period
tRFC
66
ns
PRECHARGE command period
tRP
20
ns
tRRD
15
ns
tT
0.3
WRITE recovery time
tWR
1 CLK +
7.5ns
15
Exit SELF REFRESH to ACTIVE command
tXSR
75
ACTIVE bank a to ACTIVE bank b command
Transition time
AS4SD8M16
Rev. 1.6 March 27, 2015
80,000
64 / 24
1.2
28
ns
ms
34
ns
7
ns
24
ns
25
ns
20, 35
Micross Components reserves the right to change products or specifications without notice.
29
SDRAM
AS4SD8M16
NOTES:
1. All voltages referenced to VSS.
2. This parameter is sampled. VDD, VDDQ = +3.3V; f = 1 MHz,
TA = 25°C; pin under test biased at 1.4V.
3. IDD is dependent on output loading and cycle rates. Specified values are obtained with minimum cycle time and the
outputs open.
4. Enables on-chip refresh and address counters.
5. The minimum specifications are used only to indicate cycle
time at which proper operation over the full temperature range
is ensured: (0°C < TA < +125°C for XT), (-40°C < TA < +85°C
for IT), and (-45°C < TA < +105°C for ET).
6. An initial pause of 100µs is required after power-up, followed
by two AUTO REFRESH commands, before proper device
operation is ensured. (VDD and VDDQ must be powered up simultaneously. VSS and VSSQ must be at the same potential.) The
two AUTO REFRESH command wake-ups should be repeated
any time the tREF refresh requirement is
exceeded.
7. AC characteristics assume tT = 1ns.
8. In addition to meeting the transition rate specification, the
clock and CKE must transit between VIH and VIL (or between
VIL and VIH) in a monotonic manner.
9. Outputs measured at 1.5V with equivalent load:
Q
50pF
10. tHZ defines the time at which the output achieves the open
circuit condition; it is not a reference to VOH or VOL. The last
valid data element will meet tOH before going High-Z.
11. AC operating and IDD test conditions have VIL = 0V and
VIH = 3.0V using a measurement reference level of 1.5V. If
the input transition time is longer than 1ns, then the timing is
measured from VIL (MAX) and
VIH (MIN) and no longer
from the 1.5V mid-point.
12. Other input signals are allowed to transition no more than
once every two clocks and are otherwise at valid VIH or VIL
levels.
13. IDD specifications are tested after the device is properly
initialized.
14. Timing actually specified by tCKS; clock(s) specified as a
reference only at minimum cycle rate.
15. Timing actually specified by tWR plus tRP; clock(s) specified
as a reference only at minimum cycle rate.
16. Timing actually specified by tWR.
17. Required clocks are specified by JEDEC functionality
and
AS4SD8M16
Rev. 1.6 March 27, 2015
are not dependent on any timing parameter.
18. The IDD current will increase or decrease proportionally
according to the amount of frequency alteration for the test
condition.
19. Address transitions average one transition every two
clocks.
20. CLK must be toggled a minimum of two times during this
period.
21. Based on tCK = 7.5ns for -75.
22. VIH overshoot: VIL (MAX) = VDDQ = 2V for a pulse width
< 3ns, and the pulse width cannot be greater than one third of
the cycle rate. VIL undershoot: VIL (MIN) = -2V for a pulse
width < 3ns.
23. The clock frequency must remain constant (stable clock is
defined as a signal cycling within timing constraints specified
for the clock pin) during access or precharge states (READ,
WRITE, including tWR, and PRECHARGE commands). CKE
may be used to reduce the data rate.
24. Auto precharge mode only. The precharge timing budget
(tRP) begins 7.5ns after the first clock delay, after the last WRITE
is executed. May not exceed limit set for precharge mode.
25. Precharge mode only.
26. JEDEC and PC100 specify three clock.
27. for -75 at CL = 3 with no load is 4.6ns and is guaranteed
by design.
28. Parameter guaranteed by design.
29. PC100 specifies a maximum of 4pF.
30. PC100 specifies a maximum of 5pF.
31. PC100 specifies a maximum of 6.5pF.
32. CL = 3 and tCK = 7.5ns.
33. CKE is HIGH during refresh command period tRFC (MIN)
else CKE is LOW. The IDD6 limit is actually a nominal value
and does not result in a fail value.
34. 64ms refresh for IT, ET temperature options, 24ms refresh
for XT temperature option.
35. Self refresh mode available for IT and ET only.
Micross Components reserves the right to change products or specifications without notice.
30
SDRAM
AS4SD8M16
INITIALIZE AND LOAD MODE REGISTER2
TIMING PARAMETERS
-75
SYMBOL*
MIN
tAH
-75
MAX
UNITS
SYMBOL*
MIN
MAX
0.8
ns
tCKS
1.5
ns
tAS
1.5
ns
tCMH
0.8
ns
tCH
2.5
ns
tCMS
1.5
ns
2
tCK
UNITS
tCL
2.5
ns
3
tMRD
tCK(3)
7.5
ns
tRFC
66
ns
tCK(2)
10
ns
tRP
20
ns
tCKH
0.8
*CAS latency indicated in parentheses.
ns
NOTES:
1. The mode register may be loaded prior to the AUTO REFRESH cycles if desired.
2. If CS is HIGH at clock HIGH time, all commands applied are NOP, with CKE a “Don’t Care”.
3. JEDEC and PC100 specify three clocks
4. Outputs are guaranteed High-Z after command is issued.
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
31
SDRAM
AS4SD8M16
POWER DOWN MODE1
TIMING PARAMETERS
-75
SYMBOL*
MIN
tAH
-75
MAX
UNITS
SYMBOL*
MIN
0.8
ns
tCK(2)
10
ns
tAS
1.5
ns
tCKH
0.8
ns
tCH
2.5
ns
tCKS
1.5
ns
tCL
2.5
ns
tCMH
0.8
ns
ns
tCMS
1.5
ns
tCK(3)
7
*CAS latency indicated in parentheses.
MAX
UNITS
NOTES:
1. Violating refresh requirements during power-down may result in loss of data.
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
32
SDRAM
AS4SD8M16
CLOCK SUSPEND MODE1
TIMING PARAMETERS
-75
MIN
-75
MAX
UNITS
SYMBOL*
MIN
tAC(3)
5.4
ns
tCKS
1.5
ns
tAC(2)
6
ns
tCMH
0.8
ns
SYMBOL*
MAX
UNITS
tAH
0.8
ns
tCMS
1.5
ns
tAS
1.5
ns
tDH
0.8
ns
tCH
2.5
ns
tDS
1.5
ns
tCL
2.5
ns
tHZ(3)
5.4
ns
tCK(3)
7.5
ns
tHZ(2)
6
ns
tCK(2)
10
ns
tLZ
1
ns
tCKH
0.8
ns
tOH
3
ns
*CAS latency indicated in parentheses.
NOTES:
1. For this example, the burst length = 2, the CAS latency = 3, and auto precharge is disabled.
2. A9, A11 = “Don’t Care”
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
33
SDRAM
AS4SD8M16
AUTO REFRESH MODE (IT & ET Temp options ONLY)
TIMING PARAMETERS
-75
SYMBOL*
MIN
tAH
-75
MAX
UNITS
SYMBOL*
MIN
MAX
0.8
ns
tCKH
0.8
ns
tAS
1.5
ns
tCKS
1.5
ns
tCH
2.5
ns
tCMH
0.8
ns
tCL
2.5
ns
tCMS
1.5
ns
tCK(3)
7.5
ns
tRFC
66
ns
tCK(2)
10
ns
tRP
20
ns
UNITS
*CAS latency indicated in parentheses.
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
34
SDRAM
AS4SD8M16
SELF REFRESH MODE (IT & ET Temp options ONLY)
TIMING PARAMETERS
-75
SYMBOL*
MIN
tAH
-75
MAX
UNITS
SYMBOL*
MIN
0.8
ns
tCKS
1.5
MAX
ns
tAS
1.5
ns
tCMH
0.8
ns
tCH
2.5
ns
tCMS
1.5
ns
tCL
2.5
ns
tRAS
44
tCK(3)
7.5
ns
tRP
20
ns
tCK(2)
10
ns
tXSR
75
ns
tCKH
0.8
ns
80,000
UNITS
ns
*CAS latency indicated in parentheses.
NOTES:
1. No maximum time limit for Self Refresh. tRAS(MAX) applied to non-Self Refresh mode.
2. tXSR requires minimum of two clocks regardless of frequency or timing.
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
35
SDRAM
AS4SD8M16
READ - WITHOUT AUTO PRECHARGE1
TIMING PARAMETERS
-75
MIN
-75
MAX
UNITS
SYMBOL*
MIN
tAC(3)
5.4
ns
tCMH
0.8
ns
tAC(2)
6
ns
tCMS
1.5
ns
SYMBOL*
MAX
UNITS
tAH
0.8
ns
tHZ(3)
5.4
ns
tAS
1.5
ns
tHZ(2)
6
ns
tCH
2.5
ns
tLZ
1
ns
tCL
2.5
ns
tOH
3
ns
tCK(3)
7.5
ns
tRAS
44
tCK(2)
10
ns
tRC
66
ns
tCKH
0.8
ns
tRCD
20
ns
tCKS
1.5
ns
tRP
20
ns
*CAS latency indicated in parentheses.
80,000
ns
NOTES:
1. For this example, the burst length = 4, the CAS latency = 2, and the READ burst is followed by a “manual” PRECHARGE.
2. A9, A11= “Don’t Care”
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
36
SDRAM
AS4SD8M16
READ - WITH AUTO PRECHARGE1
TIMING PARAMETERS
-75
MIN
-75
MAX
UNITS
SYMBOL*
MIN
tAC(3)
5.4
ns
tCMH
0.8
ns
tAC(2)
6
ns
tCMS
1.5
ns
SYMBOL*
MAX
UNITS
tAH
0.8
ns
tHZ(3)
5.4
ns
tAS
1.5
ns
tHZ(2)
6
ns
tCH
2.5
ns
tLZ
1
ns
tCL
2.5
ns
tOH
3
ns
tCK(3)
7.5
ns
tRAS
44
tCK(2)
10
ns
tRC
66
ns
tCKH
0.8
ns
tRCD
20
ns
tCKS
1.5
ns
tRP
20
ns
80,000
ns
*CAS latency indicated in parentheses.
NOTES:
1. For this example, the burst length = 4, the CAS latency = 2, and the READ burst is followed by a “manual” PRECHARGE.
2. A9, A11= “Don’t Care”
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
37
SDRAM
AS4SD8M16
SINGLE READ - WITHOUT AUTO PRECHARGE1
TIMING PARAMETERS
-75
MIN
-75
MAX
UNITS
SYMBOL*
MIN
tAC(3)
5.4
ns
tCMH
0.8
ns
tAC(2)
6
ns
tCMS
1.5
ns
SYMBOL*
MAX
UNITS
tAH
0.8
ns
tHZ(3)
5.4
ns
tAS
1.5
ns
tHZ(2)
6
ns
tCH
2.5
ns
tLZ
1
ns
tCL
2.5
ns
tOH
3
ns
tCK(3)
7.5
ns
tRAS
44
tCK(2)
10
ns
tRC
66
ns
tCKH
0.8
ns
tRCD
20
ns
tCKS
1.5
ns
tRP
20
ns
*CAS latency indicated in parentheses.
80,000
ns
NOTES:
1. For this example, the burst length = 1, the CAS latency = 2, and the READ burst is followed by a “manual” PRECHARGE.
2. A9, A11= “Don’t Care”
3. PRECHARGE command not allowed else tRAS would be violated.
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
38
SDRAM
AS4SD8M16
SINGLE READ - WITH AUTO PRECHARGE1
TIMING PARAMETERS
-75
UNITS
SYMBOL*
MIN
tAC(3)
5.4
ns
tCMH
0.8
ns
tAC(2)
6
ns
tCMS
1.5
ns
ns
tHZ(3)
tAH
MIN
-75
MAX
SYMBOL*
0.8
MAX
UNITS
5.4
ns
6
ns
tAS
1.5
ns
tHZ(2)
tCH
2.5
ns
tLZ
1
ns
tCL
2.5
ns
tOH
3
ns
tCK(3)
7.5
ns
tRAS
44
tCK(2)
10
ns
tRC
66
ns
tCKH
0.8
ns
tRCD
20
ns
tCKS
1.5
ns
tRP
20
ns
80,000
ns
*CAS latency indicated in parentheses.
NOTES:
1. For this example, the burst length = 1, the CAS latency = 2.
2. A9, A11 = “Don’t Care”
3. READ command not allowed else tRAS would be violated.
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
39
SDRAM
AS4SD8M16
ALTERNATING BANK READ ACCESSES1
TIMING PARAMETERS
-75
MIN
-75
MAX
UNITS
SYMBOL*
MIN
tAC(3)
5.4
ns
tCMH
0.8
ns
tAC(2)
6
ns
tCMS
1.5
ns
SYMBOL*
MAX
UNITS
tAH
0.8
ns
tLZ
1
ns
tAS
1.5
ns
tOH
3
ns
tCH
2.5
ns
tRAS
44
tCL
2.5
ns
tRC
66
ns
tCK(3)
7.5
ns
tRCD
20
ns
tCK(2)
10
ns
tRP
20
ns
tCKH
0.8
ns
tRRD
15
ns
tCKS
1.5
ns
80,000
ns
*CAS latency indicated in parentheses.
NOTES:
1. For this example, the burst length = 4, the CAS latency = 2.
2. A9, A11= “Don’t Care”
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
40
SDRAM
AS4SD8M16
READ - FULL-PAGE BURST1
TIMING PARAMETERS
-75
MIN
-75
MAX
UNITS
SYMBOL*
MIN
tAC(3)
5.4
ns
tCKS
1.5
ns
tAC(2)
6
ns
tCMH
0.8
ns
1.5
ns
SYMBOL*
MAX
UNITS
tAH
0.8
ns
tCMS
tAS
1.5
ns
tHZ(3)
5.4
ns
tCH
2.5
ns
tHZ(2)
6
ns
tCL
2.5
ns
tLZ
1
ns
tCK(3)
7.5
ns
tOH
3
ns
tCK(2)
10
ns
tRCD
20
ns
tCKH
0.8
ns
*CAS latency indicated in parentheses.
NOTES:
1. For this example, the CAS latency = 2.
2. A9, A11= “Don’t Care”
3. Page left open; no tRP.
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
41
SDRAM
AS4SD8M16
READ - DQM OPERATION1
TIMING PARAMETERS
-75
MIN
-75
MAX
UNITS
SYMBOL*
MIN
tAC(3)
5.4
ns
tCKS
1.5
ns
tAC(2)
6
ns
tCMH
0.8
ns
1.5
ns
SYMBOL*
MAX
UNITS
tAH
0.8
ns
tCMS
tAS
1.5
ns
tHZ(3)
5.4
ns
tCH
2.5
ns
tHZ(2)
6
ns
tCL
2.5
ns
tLZ
1
ns
tCK(3)
7.5
ns
tOH
3
ns
tCK(2)
10
ns
tRCD
20
ns
tCKH
0.8
ns
*CAS latency indicated in parentheses.
NOTES:
1. For this example, the burst length = 4, the CAS latency = 2.
2. A9, A11= “Don’t Care”
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
42
SDRAM
AS4SD8M16
WRITE - WITHOUT AUTO PRECHARGE1
TIMING PARAMETERS
-75
SYMBOL*
MIN
tAH
-75
MAX
UNITS
SYMBOL*
MIN
MAX
0.8
ns
tCMS
1.5
ns
tAS
1.5
ns
tDH
0.8
ns
tCH
2.5
ns
tDS
1.5
ns
tCL
2.5
ns
tRAS
44
tCK(3)
7.5
ns
tRC
66
ns
tCK(2)
10
ns
tRCD
20
ns
tCKH
0.8
ns
tRP
20
ns
tCKS
1.5
ns
tWR
15
ns
tCMH
0.8
ns
80,000
UNITS
ns
*CAS latency indicated in parentheses.
NOTES:
1. For this example, the burst length = 4, and the WRITE burst is followed by a “manual” PRECHARGE.
2. 14ns to 15ns is required between <DIN m + 3> and the PRECHARGE command, regardless of frequency.
3. A9, A11= “Don’t Care”
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
43
SDRAM
AS4SD8M16
WRITE - WITH AUTO PRECHARGE1
TIMING PARAMETERS
-75
SYMBOL*
MIN
tAH
-75
MAX
UNITS
SYMBOL*
MIN
MAX
0.8
ns
tCMS
1.5
ns
tAS
1.5
ns
tDH
0.8
ns
tCH
2.5
ns
tDS
1.5
ns
tCL
2.5
ns
tRAS
44
tCK(3)
7.5
ns
tRC
66
ns
tCK(2)
10
ns
tRCD
20
ns
tCKH
0.8
ns
tRP
20
ns
tCKS
1.5
ns
tWR
1 CLK +
7.5ns
---
tCMH
0.8
ns
80,000
UNITS
ns
*CAS latency indicated in parentheses.
NOTES:
1. For this example, the burst length = 4.
2. A9, A11= “Don’t Care”
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
44
SDRAM
AS4SD8M16
SINGLE WRITE - WITHOUT AUTO PRECHARGE1
TIMING PARAMETERS
-75
SYMBOL*
MIN
tAH
-75
MAX
UNITS
SYMBOL*
MIN
MAX
0.8
ns
tCMS
1.5
ns
tAS
1.5
ns
tDH
0.8
ns
tCH
2.5
ns
tDS
1.5
ns
tCL
2.5
ns
tRAS
44
tCK(3)
7.5
ns
tRC
66
ns
tCK(2)
10
ns
tRCD
20
ns
tCKH
0.8
ns
tRP
20
ns
tCKS
1.5
ns
tWR
15
ns
tCMH
0.8
ns
80,000
UNITS
ns
*CAS latency indicated in parentheses.
NOTES:
1. For this example, the burst length = 1, and the WRITE burst is followed by a “manual” PRECHARGE.
2. 14ns to 15ns is required between <DIN m> and the PRECHARGE command, regardless of frequency. With a single write tWR has been increased to meet
minimum tRAS requirement.
3. A9, A11= “Don’t Care”
4. PRECHARGE command not allowed else tRAS would be violated.
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
45
SDRAM
AS4SD8M16
SINGLE WRITE - WITH AUTO PRECHARGE1
TIMING PARAMETERS
-75
SYMBOL*
MIN
tAH
-75
MAX
UNITS
SYMBOL*
MIN
MAX
0.8
ns
tCMS
1.5
ns
tAS
1.5
ns
tDH
0.8
ns
tCH
2.5
ns
tDS
1.5
ns
tCL
2.5
ns
tRAS
44
tCK(3)
7.5
ns
tRC
66
ns
tCK(2)
10
ns
tRCD
20
ns
tCKH
0.8
ns
tRP
20
ns
tCKS
1.5
ns
tWR
1 CLK +
7.5ns
---
tCMH
0.8
ns
80,000
UNITS
ns
*CAS latency indicated in parentheses.
NOTES:
1. For this example, the burst length = 1.
2. Requires one clock plus time (7.5ns) with auto precharge or 14ns to 15ns with PRECHARGE.
3. A9, A11= “Don’t Care”
4. WRITE command not allowed else tRAS would be violated.
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
46
SDRAM
AS4SD8M16
ALTERNATING BANK WRITE ACCESSES1
TIMING PARAMETERS
-75
SYMBOL*
MIN
tAH
-75
MAX
UNITS
SYMBOL*
MIN
MAX
0.8
ns
tCMS
1.5
ns
tAS
1.5
ns
tDH
0.8
ns
tCH
2.5
ns
tDS
1.5
ns
tCL
2.5
ns
tRAS
44
tCK(3)
7.5
ns
tRC
66
ns
tCK(2)
10
ns
tRCD
20
ns
tCKH
0.8
ns
tRP
20
ns
tCKS
1.5
ns
tRRD
15
ns
tCMH
0.8
ns
tWR
Note 2
ns
80,000
UNITS
ns
*CAS latency indicated in parentheses.
NOTES:
1. For this example, the burst length = 4.
2. Requires one clock plus time (7.5ns) with auto precharge or 14ns to 15ns with PRECHARGE.
3. A9, A11 = “Don’t Care”
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
47
SDRAM
AS4SD8M16
WRITE - FULL-PAGE BURST
TIMING PARAMETERS
-75
SYMBOL*
MIN
tAH
-75
MAX
UNITS
SYMBOL*
MIN
0.8
ns
tCKS
MAX
1.5
ns
tAS
1.5
ns
tCMH
0.8
ns
tCH
2.5
ns
tCMS
1.5
ns
UNITS
tCL
2.5
ns
tDH
0.8
ns
tCK(3)
7.5
ns
tDS
1.5
ns
tCK(2)
10
ns
tRCD
20
ns
tCKH
0.8
ns
*CAS latency indicated in parentheses.
NOTES:
1. A9, A11 = “Don’t Care”
2. tWR must be satisfied prior to PRECHARGE command.
3. Page left open; no tRP.
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
48
SDRAM
AS4SD8M16
WRITE - DQM OPERATION1
TIMING PARAMETERS
-75
SYMBOL*
MIN
tAH
-75
MAX
UNITS
SYMBOL*
MIN
MAX
0.8
ns
tCKS
1.5
ns
tAS
1.5
ns
tCMH
0.8
ns
tCH
2.5
ns
tCMS
1.5
ns
tCL
2.5
ns
tDH
0.8
ns
tCK(3)
7.5
ns
tDS
1.5
ns
tCK(2)
10
ns
tRCD
20
ns
tCKH
0.8
ns
UNITS
*CAS latency indicated in parentheses.
NOTES:
1. For this example, the burst length = 4.
2. A9, A11 = “Don’t Care”
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
49
SDRAM
AS4SD8M16
MECHANICAL DEFINITIONS
Micross Case #901 (Package Designator DG)
3. Package may or may not be assembled with a location notch.
AS4SD8M16
Rev. 1.6 March 27, 2015
Micross Components reserves the right to change products or specifications without notice.
50
SDRAM
AS4SD8M16
ORDERING INFORMATION
Device Number
Package Type
Speed
Process
AS4SD8M16DG-75/IT
54-pin TSOPII, PbSn plating
133MHz
Industrial
AS4SD8M16DG-75/ET
54-pin TSOPII, PbSn plating
133MHz
Enhanced
AS4SD8M16DG-75/XT
54-pin TSOPII, PbSn plating
133MHz
Military
*AVAILABLE PROCESSES
IT = Industrial Temperature Range
ET= Enhanced Temperature Range
XT = Military Temperature Range
AS4SD8M16
Rev. 1.6 March 27, 2015
-40oC to +85oC
-40°C to +105°C
-55oC to +125oC
Micross Components reserves the right to change products or specifications without notice.
51
SDRAM
AS4SD8M16
DOCUMENT TITLE
128 Mb: 8 Meg x 16 SDRAM Synchronous DRAM Memory
Rev #
1.0
HistoryRelease Date
Added DGC package &
April 2010
Copper Lead Frame information
Status
Release
1.1
Updated Features & Options - Page 1 April 2010
Added Theta symbol on page 3 before jc
Changed all references of IT+ to ET
Updated Maximum Ratings - Page 29
Updated tRAS on page 31
Release
1.2
Release
Updated Timing (Cycle Time) for the PC100 description on page 1 from
7.5 to 10
May 2011
1.3
Correction on page 31, changed November 2011
refresh period from (8,192 rows) to
(4,096 rows). Updated Functional
Block Diagram on page 2. Corrected
7.81µs to 15.625µs in last paragraph
on page 10. Pin description for address
pins corrected A0-A11, instead of
A0-A12.
Release
1.4
Removed low power option from IDD7 December 2011
on page 29
Release
1.5
Removed Cu-lead frame option
Release
AS4SD8M16
Rev. 1.6 March 27, 2015
October 2013
Micross Components reserves the right to change products or specifications without notice.
52