HMC609


Design Assistance

Customised Pack Sizes / Qtys

Assembly Assistance

Support for all industry recognised
supply formats:

Die handling consultancy

Hi-Rel die qualification

Hot & Cold die probing

Electrical test & trimming
o Waffle Pack
o Gel Pak
o Tape & Reel

Onsite storage, stockholding &
scheduling

100% Visual Inspection
o MIL-STD 883 Condition A
o MIL-STD 883 Condition A

On-site failure analysis

Bespoke 24 Hour monitored
storage systems for secure long
term product support

On-site failure analysis
Contact
[email protected]
For price, delivery and to place orders
HMC609
www.analog.com
www.micross.com
Analog Devices Welcomes
Hittite Microwave Corporation
NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
www.analog.com
www.hittite.com
THIS PAGE INTENTIONALLY LEFT BLANK
HMC609
v03.0210
GaAs PHEMT MMIC LOW NOISE
AMPLIFIER, 2 - 4 GHz
AMPLIFIERS - LOW NOISE - CHIP
1
Typical Applications
Features
The HMC609 is ideal for:
Excellent Gain Flatness: ±0.2 dB
• Fixed Microwave
High Gain: 20.5 dB
• Point-to-Multi-Point Radios
Low Noise Figure: 3 dB
• Test & Measurement Equipment
Output IP3: +36 dBm
• Radar & Sensors
Output P1dB: +22 dBm
• Military & Space
50 Ohm Matched Input/Output
Die Size: 2.1 x 1.3 x 0.1 mm
Functional Diagram
General Description
The HMC609 is a GaAs PHEMT MMIC Low Noise
Amplifier (LNA) chip which operates from 2 to 4 GHz.
The HMC609 features extremely flat performance
characteristics including 20 dB of small signal gain,
3.0 dB of noise figure and output IP3 of +36 dBm
across the operating band. This versatile LNA is ideal
for hybrid and MCM assemblies due to its compact
size, consistent output power and DC blocked RF I/
O’s. All data is measured with the chip in a 50 Ohm test
fixture connected via two 0.025 mm (1 mil) diameter
bondwires of minimal length 0.31 mm (12 mil).
Electrical Specifi cations, TA = +25° C, Vdd1 = Vdd2 = +6V, Idd1 + Idd2 = 170 mA *
Parameter
Min.
Frequency Range
Gain
Typ.
Max.
2-4
19
Gain Variation Over Temperature
Units
GHz
20.5
dB
0.005
0.01
dB/ °C
Noise Figure
3
4
dB
Input Return Loss
20
dB
Output Return Loss
17
dB
21
dBm
Saturated Output Power (Psat)
22
dBm
Output Third Order Intercept (IP3)
36
Supply Current (Idd1 + Idd2)
170
Output Power for 1 dB
Compression (P1dB)
18
dBm
220
mA
*Adjust Vgg1 = Vgg2 between -1.5V to -0.5V (typ. -0.9V) to achieve total drain bias of 170mA
1 - 108
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC609
v03.0210
GaAs PHEMT MMIC LOW NOISE
AMPLIFIER, 2 - 4 GHz
22
25
20
21
10
20
S21
S11
S22
5
GAIN (dB)
RESPONSE (dB)
15
0
-5
19
18
+25C
+85C
-55C
-10
17
-15
-20
16
-25
-30
15
1
2
3
4
5
6
7
8
2
9
2.25
2.5
FREQUENCY (GHz)
3
3.25
3.5
3.75
4
Output Return Loss vs. Temperature
0
0
-5
-5
+25C
+85C
-55C
-10
RETURN LOSS (dB)
RETURN LOSS (dB)
2.75
FREQUENCY (GHz)
Input Return Loss vs. Temperature
-15
-20
-25
+25C
+85C
-55C
-10
-15
-20
-25
-30
-35
-30
2
2.25
2.5
2.75
3
3.25
3.5
3.75
4
2
2.25
2.5
FREQUENCY (GHz)
25
24
24
23
23
Psat (dBm)
26
25
22
21
20
3.25
3.5
3.75
4
3.5
3.7
4
22
21
20
19
+25C
+85C
-55C
18
3
Psat vs. Temperature
26
19
2.75
FREQUENCY (GHz)
P1dB vs. Temperature
P1dB (dBm)
1
Gain vs. Temperature
AMPLIFIERS - LOW NOISE - CHIP
Broadband Gain & Return Loss
+25C
+85C
-55C
18
17
17
16
16
2
2.2
2.5
2.7
3
3.2
FREQUENCY (GHz)
3.5
3.7
4
2
2.2
2.5
2.7
3
3.2
FREQUENCY (GHz)
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
1 - 109
HMC609
v03.0210
GaAs PHEMT MMIC LOW NOISE
AMPLIFIER, 2 - 4 GHz
Power Compression @ 3 GHz
Output IP3 vs. Temperature
40
39
20
38
37
OIP3 (dBm)
Pout (dBm), GAIN (dB), PAE (%)
25
15
10
35
34
+25C
+85C
-55C
32
31
30
-8
-6
-4
-2
0
2
4
6
2
2.25
2.5
INPUT POWER (dBm)
2.75
3
3.25
3.5
3.75
4
FREQUENCY (GHz)
Noise Figure vs. Temperature
Reverse Isolation vs. Temperature
10
0
9
-5
-10
8
ISOLATION (dB)
-15
7
+25C
+85C
-55C
6
5
4
3
-20
+25C
+85C
-55C
-25
-30
-35
-40
-45
2
-50
1
-55
0
-60
2
2.25
2.5
2.75
3
3.25
FREQUENCY (GHz)
1 - 110
36
33
Pout
Gain
PAE
5
0
-10
NOISE FIGURE (dB)
AMPLIFIERS - LOW NOISE - CHIP
1
3.5
3.75
4
2
2.25
2.5
2.75
3
3.25
3.5
3.75
4
FREQUENCY (GHz)
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC609
v03.0210
GaAs PHEMT MMIC LOW NOISE
AMPLIFIER, 2 - 4 GHz
Drain Bias Voltage (Vdd)
7 Vdc
RF Input Power (RFIN)(Vdd = +5 Vdc)
+15 dBm
Channel Temperature
175 °C
Continuous Pdiss (T = 85 °C)
(derate 18 mW/°C above 85 °C)
1.64 W
Thermal Resistance
(channel to ground pad)
55 °C/W
Storage Temperature
-65 to +150 °C
Operating Temperature
-55 to +85 °C
Vdd (V)
Idd (mA)
+5.5
160
+6.0
170
+6.5
180
Note: Amplifier will operate over full voltage range shown above
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Outline Drawing
Die Packaging Information [1]
Standard
Alternate
GP-2 (Gel Pack)
[2]
[1] Refer to the “Packaging Information” section for die
packaging dimensions.
[2] For alternate packaging information contact Hittite
Microwave Corporation.
1
AMPLIFIERS - LOW NOISE - CHIP
Typical Supply Current vs. Vdd
Absolute Maximum Ratings
NOTES:
1. ALL DIMENSIONS IN INCHES [MILLIMETERS]
2. DIE THICKNESS IS 0.007”
3. TYPICAL BOND PAD IS 0.004” SQUARE
4. BACKSIDE METALLIZATION: GOLD
5. BACKSIDE METAL IS GROUND
6. BOND PAD METALIZATION: GOLD
7. NO CONNECTION REQUIRED FOR UNLABELED BOND PADS
8. OVERALL DIE SIZE ±0.002”
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
1 - 111
HMC609
v03.0210
AMPLIFIERS - LOW NOISE - CHIP
1
1 - 112
GaAs PHEMT MMIC LOW NOISE
AMPLIFIER, 2 - 4 GHz
Pad Descriptions
Pad Number
Function
Description
1
RFIN
This pad is AC coupled and
matched to 50 Ohms.
2, 5, 6, 10
Die Bottom
GND
These pads & die bottom must be
connected to RF/DC ground.
3, 4
Vdd1, Vdd2
Power Supply Voltage for the amplifier.
External bypass capacitors of
100 pF & 0.1 μF are required.
7
RFOUT
This pad is AC coupled and
matched to 50 Ohms.
8, 9
Vgg2, Vgg1
Gates supply voltage for the amplifier. External bypass
capacitors of 100 pF and 0.1 μF are required.
Interface Schematic
Assembly Diagram
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC609
v03.0210
GaAs PHEMT MMIC LOW NOISE
AMPLIFIER, 2 - 4 GHz
The die should be attached directly to the ground plane eutectically or with
conductive epoxy (see HMC general Handling, Mounting, Bonding Note).
50 Ohm Microstrip transmission lines on 0.127mm (5 mil) thick alumina thin film
substrates are recommended for bringing RF to and from the chip (Figure 1). If
0.254mm (10 mil) thick alumina thin film substrates must be used, the die should be
raised 0.150mm (6 mils) so that the surface of the die is coplanar with the surface
of the substrate. One way to accomplish this is to attach the 0.102mm (4 mil) thick
die to a 0.150mm (6 mil) thick molybdenum heat spreader (moly-tab) which is then
attached to the ground plane (Figure 2).
0.102mm (0.004”) Thick GaAs MMIC
Wire Bond
0.076mm
(0.003”)
RF Ground Plane
Microstrip substrates should be brought as close to the die as possible in order to
minimize bond wire length. Typical die-to-substrate spacing is 0.076mm (3 mils).
Handling Precautions
0.127mm (0.005”) Thick Alumina
Thin Film Substrate
Follow these precautions to avoid permanent damage.
Storage: All bare die are placed in either Waffle or Gel based ESD protective
containers, and then sealed in an ESD protective bag for shipment. Once the
sealed ESD protective bag has been opened, all die should be stored in a dry
nitrogen environment.
Cleanliness: Handle the chips in a clean environment. DO NOT attempt to clean
the chip using liquid cleaning systems.
Static Sensitivity: Follow ESD precautions to protect against > ± 250V ESD
strikes.
Transients: Suppress instrument and bias supply transients while bias is applied.
Use shielded signal and bias cables to minimize inductive pick-up.
General Handling: Handle the chip along the edges with a vacuum collet or with
a sharp pair of bent tweezers. The surface of the chip has fragile air bridges and
should not be touched with vacuum collet, tweezers, or fingers.
Mounting
The chip is back-metallized and can be die mounted with AuSn eutectic preforms
or with electrically conductive epoxy. The mounting surface should be clean and
flat.
Figure 1.
0.102mm (0.004”) Thick GaAs MMIC
Wire Bond
0.076mm
(0.003”)
RF Ground Plane
0.150mm (0.005”) Thick
Moly Tab
AMPLIFIERS - LOW NOISE - CHIP
1
Mounting & Bonding Techniques for Millimeterwave GaAs MMICs
0.254mm (0.010”) Thick Alumina
Thin Film Substrate
Figure 2.
Eutectic Die Attach: A 80/20 gold tin preform is recommended with a work surface temperature of 255 °C and a tool temperature
of 265 °C. When hot 90/10 nitrogen/hydrogen gas is applied, tool tip temperature should be 290 °C. DO NOT expose the chip
to a temperature greater than 320 °C for more than 20 seconds. No more than 3 seconds of scrubbing should be required for
attachment.
Epoxy Die Attach: Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy fillet is observed around the
perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer’s schedule.
Wire Bonding
Ball or wedge bond with 0.025 mm (1 mil) diameter pure gold wire is recommended. Thermosonic wirebonding with a nominal stage
temperature of 150 °C and a ball bonding force of 40 to 50 grams or wedge bonding force of 18 to 22 grams is recommended. Use
the minimum level of ultrasonic energy to achieve reliable wirebonds. Wirebonds should be started on the chip and terminated
on the package or substrate. All bonds should be as short as possible <0.31 mm (12 mils).
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
1 - 113