HMC460


Design Assistance

Customised Pack Sizes / Qtys

Assembly Assistance

Support for all industry recognised
supply formats:

Die handling consultancy

Hi-Rel die qualification

Hot & Cold die probing

Electrical test & trimming
o Waffle Pack
o Gel Pak
o Tape & Reel

Onsite storage, stockholding &
scheduling

100% Visual Inspection
o MIL-STD 883 Condition A
o MIL-STD 883 Condition A

On-site failure analysis

Bespoke 24 Hour monitored
storage systems for secure long
term product support

On-site failure analysis
Contact
[email protected]
For price, delivery and to place orders
HMC460
www.analog.com
www.micross.com
Analog Devices Welcomes
Hittite Microwave Corporation
NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
www.analog.com
www.hittite.com
THIS PAGE INTENTIONALLY LEFT BLANK
HMC460
v05.0612
AMPLIFIERS - LOW NOISE - CHIP
GaAs pHEMT MMIC LOW NOISE
AMPLIFIER, DC - 20 GHz
Typical Applications
Features
The HMC460 is ideal for:
Noise Figure: 2.5 dB @ 10 GHz
• Telecom Infrastructure
Gain: 14 dB @ 10 GHz
• Microwave Radio & VSAT
P1dB Output Power: +16 dBm @ 10 GHz
• Military & Space
Supply Voltage: +8V @ 60 mA
• Test Instrumentation
50 Ohm Matched Input/Output
Die Size: 3.12 x 1.63 x 0.1 mm
General Description
Functional Diagram
The HMC460 is a GaAs MMIC PHEMT Low Noise
Distributed Amplifier die which operates between DC
and 20 GHz. The amplifier provides 14 dB of gain,
2.5 dB noise figure and +16 dBm of output power at
1 dB gain compression while requiring only 60 mA
from a +8V supply. The HMC460 amplifier can easily
be integrated into Multi-Chip-Modules (MCMs) due to
its small size. All data is with the chip in a 50 Ohm test
fixture connected via 0.025mm (1 mil) diameter wire
bonds of minimal length 0.31mm (12 mils).
Electrical Specifications, TA = +25° C, Vdd= 8V, Idd= 60 mA*
Parameter
Min.
Frequency Range
Gain
Typ.
Max.
Min.
DC - 6.0
12
Gain Flatness
14
12
± 0.5
Gain Variation Over Temperature
Typ.
Max.
Min.
6.0 - 18.0
14
11
± 0.15
Typ.
Max.
Units
18.0 - 20.0
GHz
13
dB
± 0.25
dB
0.008
0.016
0.01
0.02
0.01
0.02
dB/ °C
Noise Figure
4.0
5.0
2.5
3.5
3.0
4.0
dB
Input Return Loss
17
22
15
Output Return Loss
17
15
15
dB
15
dBm
Output Power for 1 dB Compression (P1dB)
Saturated Output Power (Psat)
14
17
13
16
12
dB
18
18
17
dBm
Output Third Order Intercept (IP3)
27.5
28
27
dBm
Supply Current
(Idd) (Vdd= 8V, Vgg1= -0.9V Typ.)
60
60
60
mA
* Adjust Vgg between -2 to 0V to achieve Idd= 60 mA typical.
1
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC460
v05.0612
GaAs pHEMT MMIC LOW NOISE
AMPLIFIER, DC - 20 GHz
Broadband Gain & Return Loss
Gain vs. Temperature
20
20
16
5
0
GAIN (dB)
RESPONSE (dB)
10
-5
-10
-15
12
8
-20
4
-25
-30
-35
0
0
2
4
6
8
10 12 14 16 18
FREQUENCY (GHz)
S21
20
22
S11
24
26
2
4
S22
Input Return Loss vs. Temperature
0
-5
-5
-15
-20
-25
18
+85 C
20
22
-55 C
-10
-15
-20
-25
-30
-35
-30
0
2
4
6
8
10
12
14
16
18
20
0
22
2
4
6
FREQUENCY (GHz)
+25 C
+85 C
-55 C
10
12
+25 C
14
16
18
20
22
+85 C
-55 C
Noise Figure vs. Temperature
10
8
NOISE FIGURE (dB)
25
20
15
10
5
0
-5
-10
-15
-20
-25
-30
-35
-40
0.00001
8
FREQUENCY (GHz)
Low Frequency Gain & Return Loss
RESPONSE (dB)
8
10 12 14 16
FREQUENCY (GHz)
Output Return Loss vs. Temperature
0
-10
6
+25 C
RETURN LOSS (dB)
RETURN LOSS (dB)
0
AMPLIFIERS - LOW NOISE - CHIP
15
6
4
2
0
0.0001
0.001
0.01
0.1
1
10
0
2
4
6
S21
S11
8
10
12
14
16
18
20
22
FREQUENCY (GHz)
FREQUENCY (GHz)
S22
+25 C
+85 C
-55 C
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
2
HMC460
v05.0612
GaAs pHEMT MMIC LOW NOISE
AMPLIFIER, DC - 20 GHz
25
22
22
PSAT (dBm)
P1dB (dBm)
Psat vs. Temperature
25
19
16
13
19
16
13
10
10
0
2
4
6
+25 C
8
10 12 14 16
FREQUENCY (GHz)
18
+85 C
20
22
0
2
4
6
-55 C
8
10 12 14 16
FREQUENCY (GHz)
+25 C
+85 C
18
20
22
-55 C
Gain, Power & Noise Figure
vs. Supply Voltage @ 10 GHz, Fixed Vgg1
Output IP3 vs. Temperature
32
18
5
16
4
14
3
12
2
10
1
GAIN (dB), P1dB (dBm)
30
IP3 (dBm)
28
26
24
22
NOISE FIGURE (dB)
AMPLIFIERS - LOW NOISE - CHIP
Output P1dB vs. Temperature
20
18
0
8
0
2
4
6
+25 C
8
10 12 14 16
FREQUENCY (GHz)
18
20
22
7.5
7.75
8
8.25
8.5
Vdd (V)
+85 C
-55 C
GAIN
P1dB
NOISE FIGURE
Reverse Isolation vs. Temperature
REVERSE ISOLATION (dB)
0
-10
-20
-30
-40
-50
-60
-70
0
2
4
6
8
10
12
14
16
18
20
22
FREQUENCY (GHz)
+25 C
3
+85 C
-55 C
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC460
v05.0612
GaAs pHEMT MMIC LOW NOISE
AMPLIFIER, DC - 20 GHz
Drain Bias Voltage (Vdd)
+9 Vdc
Gate Bias Voltage (Vgg)
-2 to 0 Vdc
Gate Bias Voltage (Igg)
2.5 mA
RF Input Power (RFIN)(Vdd = +8 Vdc)
+18 dBm
Channel Temperature
175 °C
Continuous Pdiss (T = 85 °C)
(derate 24 mW/°C above 85 °C)
2.17 W
Thermal Resistance
(channel to die bottom)
41.5 °C/W
Storage Temperature
-65 to +150 °C
Operating Temperature
-55 to +85 °C
Vdd (V)
Idd (mA)
+7.5
59
+8.0
60
+8.5
62
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Outline Drawing
Die Packaging Information [1]
Standard
Alternate
GP-1 (Gel Pack)
[2]
[1] Refer to the “Packaging Information” section for die
packaging dimensions.
[2] For alternate packaging information contact Hittite
Microwave Corporation.
AMPLIFIERS - LOW NOISE - CHIP
Typical Supply Current vs. Vdd
Absolute Maximum Ratings
NOTES:
1. ALL DIMENSIONS IN INCHES [MILLIMETERS]
2. NO CONNECTION REQUIRED FOR UNLABELED BOND PADS
3. DIE THICKNESS IS 0.004 (0.100)
4. TYPICAL BOND PAD IS 0.004 (0.100) SQUARE
5. BACKSIDE METALLIZATION: GOLD
6. BACKSIDE METAL IS GROUND
7. BOND PAD METALIZATION: GOLD
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
4
HMC460
v05.0612
GaAs pHEMT MMIC LOW NOISE
AMPLIFIER, DC - 20 GHz
AMPLIFIERS - LOW NOISE - CHIP
Pad Descriptions
5
Pad Number
Function
Description
1
RFIN
This pad is DC coupled
and matched to 50 Ohms.
2
Vdd
Power supply voltage for the amplifier.
External bypass capacitors are required
3
ACG1
Low frequency termination. Attach bypass capacitor per
application circuit herein.
4
RFOUT
This pad is DC coupled
and matched to 50 Ohms.
5
ACG2
Low frequency termination. Attach bypass capacitor per
application circuit herein.
6
Vgg
Gate control for amplifier. Adjust to achieve Idd= 60 mA.
Die
Bottom
GND
Die bottom must be connected to RF/DC ground.
Interface Schematic
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC460
v05.0612
GaAs pHEMT MMIC LOW NOISE
AMPLIFIER, DC - 20 GHz
AMPLIFIERS - LOW NOISE - CHIP
Assembly Diagram
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
6
HMC460
v05.0612
GaAs pHEMT MMIC LOW NOISE
AMPLIFIER, DC - 20 GHz
AMPLIFIERS - LOW NOISE - CHIP
Mounting & Bonding Techniques for Millimeterwave GaAs MMICs
The die should be attached directly to the ground plane eutectically or with
conductive epoxy (see HMC general Handling, Mounting, Bonding Note).
50 Ohm Microstrip transmission lines on 0.127mm (5 mil) thick alumina
thin film substrates are recommended for bringing RF to and from the chip
(Figure 1). If 0.254mm (10 mil) thick alumina thin film substrates must be
used, the die should be raised 0.150mm (6 mils) so that the surface of
the die is coplanar with the surface of the substrate. One way to accomplish this is to attach the 0.102mm (4 mil) thick die to a 0.150mm (6 mil)
thick molybdenum heat spreader (moly-tab) which is then attached to the
ground plane (Figure 2).
0.102mm (0.004”) Thick GaAs MMIC
Wire Bond
0.076mm
(0.003”)
RF Ground Plane
Microstrip substrates should be located as close to the die as possible
in order to minimize bond wire length. Typical die-to-substrate spacing is
0.076mm to 0.152 mm (3 to 6 mils).
0.127mm (0.005”) Thick Alumina
Thin Film Substrate
Figure 1.
Handling Precautions
Follow these precautions to avoid permanent damage.
Storage: All bare die are placed in either Waffle or Gel based ESD protective containers, and then sealed in an ESD protective bag for shipment.
Once the sealed ESD protective bag has been opened, all die should be
stored in a dry nitrogen environment.
Cleanliness: Handle the chips in a clean environment. DO NOT attempt
to clean the chip using liquid cleaning systems.
Static Sensitivity: Follow ESD precautions to protect against > ± 250V
ESD strikes.
Transients: Suppress instrument and bias supply transients while bias is
applied. Use shielded signal and bias cables to minimize inductive pick-up.
0.102mm (0.004”) Thick GaAs MMIC
Wire Bond
0.076mm
(0.003”)
RF Ground Plane
0.150mm (0.005”) Thick
Moly Tab
0.254mm (0.010”) Thick Alumina
Thin Film Substrate
Figure 2.
General Handling: Handle the chip along the edges with a vacuum collet
or with a sharp pair of bent tweezers. The surface of the chip may have fragile air bridges and should not be touched
with vacuum collet, tweezers, or fingers.
Mounting
The chip is back-metallized and can be die mounted with AuSn eutectic preforms or with electrically conductive epoxy.
The mounting surface should be clean and flat.
Eutectic Die Attach: A 80/20 gold tin preform is recommended with a work surface temperature of 255 °C and a tool
temperature of 265 °C. When hot 90/10 nitrogen/hydrogen gas is applied, tool tip temperature should be 290 °C. DO
NOT expose the chip to a temperature greater than 320 °C for more than 20 seconds. No more than 3 seconds of
scrubbing should be required for attachment.
Epoxy Die Attach: Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy fillet is observed
around the perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer’s schedule.
Wire Bonding
Ball or wedge bond with 0.025mm (1 mil) diameter pure gold wire. Thermosonic wirebonding with a nominal stage
temperature of 150 °C and a ball bonding force of 40 to 50 grams or wedge bonding force of 18 to 22 grams is recommended. Use the minimum level of ultrasonic energy to achieve reliable wirebonds. Wirebonds should be started
on the chip and terminated on the package or substrate. All bonds should be as short as possible <0.31mm (12 mils).
7
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC460
v05.0612
GaAs pHEMT MMIC LOW NOISE
AMPLIFIER, DC - 20 GHz
AMPLIFIERS - LOW NOISE - CHIP
Notes:
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
8