HMC462


Design Assistance

Customised Pack Sizes / Qtys

Assembly Assistance

Support for all industry recognised
supply formats:

Die handling consultancy

Hi-Rel die qualification

Hot & Cold die probing

Electrical test & trimming
o Waffle Pack
o Gel Pak
o Tape & Reel

Onsite storage, stockholding &
scheduling

100% Visual Inspection
o MIL-STD 883 Condition A
o MIL-STD 883 Condition A

On-site failure analysis

Bespoke 24 Hour monitored
storage systems for secure long
term product support

On-site failure analysis
Contact
[email protected]
For price, delivery and to place orders
HMC462
www.analog.com
www.micross.com
Analog Devices Welcomes
Hittite Microwave Corporation
NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
www.analog.com
www.hittite.com
THIS PAGE INTENTIONALLY LEFT BLANK
HMC462
v02.0213
Amplifiers - Low Noise Amplifiers - Chip
GaAs pHEMT MMIC
LOW NOISE AMPLIFIER, 2 - 20 GHz
Typical Applications
Features
The HMC462 is ideal for:
Noise Figure: 2 dB
• Test Instrumentation
Gain: 15 dB
• Microwave Radio & VSAT
P1dB +15.5 dBm
• Military & Space
Self-Biased: +5V @ 63 mA
• Telecom Infrastructure
50 Ohm Matched Input/Output
• Fiber Optics
Die Size: 3.0 x 1.3 x 0.1 mm
Functional Diagram
General Description
The HMC462 is a GaAs MMIC pHEMT Low Noise
Distributed Amplifier which operates between 2
and 20 GHz. The amplifier provides 15 dB of small
signal gain, 2.5 dB noise figure, and up to +15.5 dBm
of output power at 1dB compression. Gain flatness
is excellent at ±0.3 dB from 8 - 14 GHz making the
HMC462 ideal for EW, ECM, and Radar applications.
The HMC462 requires a single supply of +5V @ 63
mA and is the self biased version of the HMC463.
The wideband amplifier I/Os are internally matched
to 50 Ohms facilitating integration into Multi-ChipModules (MCMs). All data is measured with the chip in
a 50 Ohm test fixture connected via 0.025 mm (1 mil)
diameter wire bonds of 0.31 mm (12 mils) length.
Electrical Specifications, TA = +25° C, Vdd = +5V, Idd = 63 mA
Parameter
Min.
Frequency Range
Gain
Max.
Min.
2-8
13.5
Typ.
Max.
Min.
8 - 16
15.5
13
15
12.5
Typ.
Max.
Units
16 - 20
GHz
14.5
dB
Gain Flatness
±0.2
±0.3
±0.2
dB
Gain Variation Over Temperature
0.005
0.011
0.019
dB/ °C
Input Return Loss
16
19
16
dB
Output Return Loss
18
19
18
dB
Output Power for 1 dB Compression (P1dB)
13
dBm
Saturated Output Power (Psat)
12.5
18
17
15.5
dBm
Output Third Order Intercept (IP3)
26
25
24
dBm
Noise Figure
Supply Current (Idd)
1
Typ.
15.5
11.5
3
41
63
14.5
10
2.5
84
41
63
2.5
84
41
63
dB
84
mA
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC462
v02.0213
GaAs pHEMT MMIC
LOW NOISE AMPLIFIER, 2 - 20 GHz
Gain & Return Loss
Gain vs. Temperature
16
14
GAIN (dB)
RESPONSE (dB)
10
0
-10
12
10
-20
8
-30
6
0
4
8
12
16
20
2
24
4
6
8
FREQUENCY (GHz)
S21
S11
S22
14
16
18
20
22
0
0
-10
-10
-20
+85 C
-55 C
Output Return Loss vs. Temperature
RESPONSE (dB)
RETURN LOSS (dB)
12
+25 C
Input Return Loss vs. Temperature
-20
-30
-30
-40
-40
2
4
6
8
10
12
14
16
18
20
2
22
4
6
8
+25 C
10
12
14
16
18
20
22
FREQUENCY (GHz)
FREQUENCY (GHz)
+85 C
-55 C
+25 C
+85 C
-55 C
Noise Figure vs. Temperature
Reverse Isolation vs. Temperature
0
6
-10
5
NOISE FIGURE (dB)
ISOLATION (dB)
10
FREQUENCY (GHz)
-20
-30
-40
-50
Amplifiers - Low Noise Amplifiers - Chip
18
20
4
3
2
1
-60
0
-70
2
4
6
8
10
12
14
16
18
20
+85 C
2
4
6
8
10
12
14
16
18
20
22
FREQUENCY (GHz)
FREQUENCY (GHz)
+25 C
22
-55 C
+25 C
+85 C
-55 C
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
2
HMC462
v02.0213
GaAs pHEMT MMIC
LOW NOISE AMPLIFIER, 2 - 20 GHz
22
20
20
18
18
16
16
Psat (dBm)
P1dB (dBm)
Psat vs. Temperature
22
14
12
14
12
10
10
8
8
6
6
2
4
6
8
10
12
14
16
18
20
22
2
4
6
8
FREQUENCY (GHz)
+25 C
+85 C
-55 C
14
16
18
20
22
+85 C
-55 C
Psat vs. Vdd
22
22
20
20
18
18
16
16
Psat (dBm)
P1dB (dBm)
12
+25 C
14
12
14
12
10
10
8
8
6
6
2
4
6
8
10
12
14
16
18
20
22
2
4
6
8
FREQUENCY (GHz)
+4V
10
12
14
16
18
20
22
FREQUENCY (GHz)
+5V
+6V
+4V
Output IP3 vs. Temperature
@ Pout = 4 dBm Tone
+5V
+6V
Output IP3 vs. Vdd
@ Pout = 4 dBm Tone
30
27
27
IP3 (dBm)
30
24
21
18
24
21
18
15
15
2
4
6
8
10
12
14
16
18
20
22
2
4
6
8
FREQUENCY (GHz)
+25 C
3
10
FREQUENCY (GHz)
P1dB vs. Vdd
IP3 (dBm)
Amplifiers - Low Noise Amplifiers - Chip
P1dB vs. Temperature
+85 C
10
12
14
16
18
20
22
FREQUENCY (GHz)
-55 C
+4V
+5V
+6V
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC462
v02.0213
GaAs pHEMT MMIC
LOW NOISE AMPLIFIER, 2 - 20 GHz
Power Compression @ 4 GHz
Power Compression @ 12 GHz
16
12
8
4
0
-15
-13
-11
-9
-7
-5
-3
-1
1
3
5
16
12
8
4
0
-15
7
-13
-11
-9
INPUT POWER (dBm)
Pout
Gain
PAE
-3
-1
1
3
5
7
Gain
PAE
Power Dissipation
0.6
POWER DISSIPATION (W)
20
Pout (dBm), GAIN (dB), PAE (%)
-5
Pout
Power Compression @ 20 GHz
16
12
8
4
0
-14
-7
INPUT POWER (dBm)
-12
-10
-8
-6
-4
-2
0
2
4
0.5
0.4
0.3
0.2
0.1
0
-14
-12
-10
-8
INPUT POWER (dBm)
Pout
Gain
-6
-4
-2
0
2
4
6
8
INPUT POWER (dBm)
PAE
4 GHz
12 GHz
20 GHz
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
Amplifiers - Low Noise Amplifiers - Chip
20
Pout (dBm), GAIN (dB), PAE (%)
Pout (dBm), GAIN (dB), PAE (%)
20
4
HMC462
v02.0213
GaAs pHEMT MMIC
LOW NOISE AMPLIFIER, 2 - 20 GHz
Typical Supply Current vs. Vdd
Amplifiers - Low Noise Amplifiers - Chip
Absolute Maximum Ratings
Drain Bias Voltage (Vdd)
+9 Vdc
RF Input Power (RFIN)
Channel Temperature
Continuous Pdiss (T= 85 °C)
(derate 24.4 mW/°C above
85 °C)
Vdd (V)
Idd (mA)
+18 dBm
4
64
175 °C
5
66
6
68
2.2 W
Thermal Resistance
(channel to die bottom)
41 °C/W
Storage Temperature
-65 to 150°C
Operating Temperature
-55 to 85 °C
70
8
72
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Outline Drawing
Die Packaging Information
[1]
Standard
Alternate
GP-1 (Gel Pack)
[2]
[1] For more information refer to the “Packaging
Information” Document in the Product Support Section of
our website .
[2] For alternate packaging information contact Hittite
Microwave Corporation.
5
7
NOTES:
1. ALL DIMENSIONS ARE IN INCHES [MM]
2. DIE THICKNESS IS 0.004”
3. TYPICAL BOND PAD IS 0.004” SQUARE
4. BOND PAD METALIZATION: GOLD
5. BACKSIDE METALIZATION: GOLD
6. BACKSIDE METAL IS GROUND
7. NO CONNECTION REQUIRED FOR UNLABELED BOND PADS
8. OVERALL DIE SIZE ±0.002”
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC462
v02.0213
GaAs pHEMT MMIC
LOW NOISE AMPLIFIER, 2 - 20 GHz
Pad Descriptions
Function
Description
1
RFIN
This pad is AC coupled and matched to 50 Ohms
2
Vdd
Power supply voltage for teh amplifier
External bypass capacitors are required
3
RFOUT
This pad is AC coupled and matched to 50 Ohms
Die Bottom
GND
Die bottom must be connected to RF/DC ground.
Interface Schematic
Assembly Diagram
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
Amplifiers - Low Noise Amplifiers - Chip
Pad Number
6
HMC462
v02.0213
GaAs pHEMT MMIC
LOW NOISE AMPLIFIER, 2 - 20 GHz
Amplifiers - Low Noise Amplifiers - Chip
Mounting & Bonding Techniques for Millimeterwave GaAs MMICs
The die should be attached directly to the ground plane eutectically or with conductive epoxy (see HMC general Handling, Mounting, Bonding Note).
50 Ohm Microstrip transmission lines on 0.127mm (5 mil) thick alumina thin film substrates are recommended for
bringing RF to and from the chip (Figure 1). If 0.254mm (10 mil) thick alumina thin film substrates must be used, the
die should be raised 0.150mm (6 mils) so that the surface of the die is coplanar with the surface of the substrate. One
way to accomplish this is to attach the 0.102mm (4 mil) thick die to a 0.150mm (6 mil) thick molybdenum heat spreader
(moly-tab) which is then attached to the ground plane (Figure 2).
Microstrip substrates should be located as close to the die as possible in order to minimize bond wire length. Typical
die-to-substrate spacing is 0.076mm to 0.152 mm (3 to 6 mils).
Handling Precautions
Follow these precautions to avoid permanent damage.
Storage: All bare die are placed in either Waffle or Gel based ESD protective containers, and then sealed in an ESD protective bag for shipment.
Once the sealed ESD protective bag has been opened, all die should be
stored in a dry nitrogen environment.
0.102mm (0.004”) Thick GaAs MMIC
Wire Bond
0.076mm
(0.003”)
RF Ground Plane
Cleanliness: Handle the chips in a clean environment. DO NOT attempt
to clean the chip using liquid cleaning systems.
Static Sensitivity: Follow ESD precautions to protect against > ± 250V
ESD strikes.
Transients: Suppress instrument and bias supply transients while bias is
applied. Use shielded signal and bias cables to minimize inductive pickup.
General Handling: Handle the chip along the edges with a vacuum collet
or with a sharp pair of bent tweezers. The surface of the chip may have
fragile air bridges and should not be touched with vacuum collet, tweezers, or fingers.
Mounting
The chip is back-metallized and can be die mounted with AuSn eutectic preforms or with electrically conductive epoxy. The mounting surface
should be clean and flat.
0.127mm (0.005”) Thick Alumina
Thin Film Substrate
Figure 1.
0.102mm (0.004”) Thick GaAs MMIC
Wire Bond
0.076mm
(0.003”)
RF Ground Plane
0.150mm (0.005”) Thick
Moly Tab
0.254mm (0.010”) Thick Alumina
Eutectic Die Attach: A 80/20 gold tin preform is recommended with a work
Thin Film Substrate
surface temperature of 255 °C and a tool temperature of 265 °C. When
Figure 2.
hot 90/10 nitrogen/hydrogen gas is applied, tool tip temperature should be
290 °C. DO NOT expose the chip to a temperature greater than 320 °C for more than 20 seconds. No more than 3
seconds of scrubbing should be required for attachment.
Epoxy Die Attach: Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy fillet is observed
around the perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer’s schedule.
Wire Bonding
Ball or wedge bond with 0.025mm (1 mil) diameter pure gold wire. Thermosonic wirebonding with a nominal stage
temperature of 150 °C and a ball bonding force of 40 to 50 grams or wedge bonding force of 18 to 22 grams is recommended. Use the minimum level of ultrasonic energy to achieve reliable wirebonds. Wirebonds should be started on
the chip and terminated on the package or substrate. All bonds should be as short as possible <0.31mm (12 mils).
7
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC462
v02.0213
GaAs pHEMT MMIC
LOW NOISE AMPLIFIER, 2 - 20 GHz
Amplifiers - Low Noise Amplifiers - Chip
Notes:
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
8