HMC347


Design Assistance

Customised Pack Sizes / Qtys

Assembly Assistance

Support for all industry recognised
supply formats:

Die handling consultancy

Hi-Rel die qualification

Hot & Cold die probing

Electrical test & trimming
o Waffle Pack
o Gel Pak
o Tape & Reel

Onsite storage, stockholding &
scheduling

100% Visual Inspection
o MIL-STD 883 Condition A
o MIL-STD 883 Condition A

On-site failure analysis

Bespoke 24 Hour monitored
storage systems for secure long
term product support

On-site failure analysis
Contact
[email protected]
For price, delivery and to place orders
HMC347
www.analog.com
www.micross.com
Analog Devices Welcomes
Hittite Microwave Corporation
NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
www.analog.com
www.hittite.com
THIS PAGE INTENTIONALLY LEFT BLANK
HMC347
v04.0907
SWITCHES - CHIP
4
GaAs MMIC SPDT NON-REFLECTIVE
SWITCH, DC - 20 GHz
Typical Applications
Features
This switch is suitable DC - 20 GHz applications:
High Isolation: >40 dB @ 20 GHz
• Fiber Optics
Low Insertion Loss: 1.6 dB @ 20 GHz
• Microwave Radio
Non-Reflective Design
• Military
Small Size: 1.3 x 0.8 x 0.1 mm
• Space
• VSAT
General Description
Functional Diagram
The HMC347 is a broadband non-reflective GaAs
MESFET SPDT MMIC chip. Covering DC to 20 GHz,
the switch offers high isolation and low insertion loss.
The switch features over 50 dB isolation at lower
frequencies and over 40 dB at higher frequencies due
to the implementation of on-chip via hole structures.
The switch operates using two negative control voltage logic lines of -5/0V, requires no Vee and has no
current consumption. The switch operates down to
DC. The chip features coplanar I/Os that allow 100%
RF testing prior to delivery to the customer.
Electrical Specifi cations, TA = +25° C, With 0/-5V Control, 50 Ohm System
Parameter
Frequency
Insertion Loss
Isolation
4 - 26
Min.
DC - 20.0 GHz
Typ.
Max.
Units
1.7
2.2
dB
DC - 20.0 GHz
40
45
dB
Return Loss
“On State”
DC - 20.0 GHz
10
13
dB
Return Loss RF1, RF2
“On State”
DC - 20.0 GHz
8
10
dB
Input Power for 1 dB Compression
0.5 - 20.0 GHz
19
23
dBm
Input Third Order Intercept
0.5 - 20.0 GHz
38
43
dBm
Switching Characteristics
tRISE, tFALL (10/90% RF)
tON, tOFF (50% CTL to 10/90% RF)
DC - 20.0 GHz
3
6
ns
ns
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC347
v04.0907
GaAs MMIC SPDT NON-REFLECTIVE
SWITCH, DC - 20 GHz
Insertion Loss
Isolation
0
0
ISOLATION (dB)
INSERTION LOSS (dB)
-10
-1
-2
+25C
-55C
-3
+85C
RF1
RF2
-20
-30
-40
4
-50
-4
-5
-70
0
5
10
15
20
0
25
5
10
FREQUENCY (GHz)
Return Loss
20
25
0.1 and 1 dB Input Compression Point
30
0
1 dB Compression Point
0.1 dB Compression Point
RFC
RF1,2 On
RF1,2 Off
25
P1dB (dBm)
-5
-10
-15
20
15
-20
10
-25
0
5
10
15
20
0
25
5
10
15
20
FREQUENCY (GHz)
FREQUENCY (GHz)
Input Third Order Intercept Point
50
45
IP3 (dBm)
RETURN LOSS (dB)
15
FREQUENCY (GHz)
SWITCHES - CHIP
-60
40
+25C
-55C
+85C
35
30
0
2
4
6
8
10
12
14
16
18
20
RF FREQUENCY (GHz)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
4 - 27
HMC347
v04.0907
Absolute Maximum Ratings
RF Input Power (Vctl = -5V)
SWITCHES - CHIP
4
GaAs MMIC SPDT NON-REFLECTIVE
SWITCH, DC - 20 GHz
Control Voltages
+27 dBm
State
Bias Condition
Control Voltage Range (A & B)
+0.5V to -7.5 Vdc
Low
0 to -0.2V @ 10 uA Max.
Channel Temperature
150 °C
High
-5V @ 10 uA Typ. to -7V @ 40 uA Max.
Thermal Resistance
(Insertion Loss Path)
440 °C/W
Thermal Resistance
(Terminated Path)
540 °C/W
Storage Temperature
-65 to +150 °C
Operating Temperature
-55 to +85 °C
Truth Table
Control Input
ESD Sensitivity (HBM)
Signal Path State
A
B
RFC to RF1
RFC to RF2
High
Low
ON
OFF
Low
High
OFF
ON
Class 1A
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Outline Drawing
Die Packaging Information [1]
Standard
Alternate
WP-8 (Waffle Pack)
[2]
[1] Refer to the “Packaging Information” section for die
packaging dimensions.
[2] For alternate packaging information contact Hittite
Microwave Corporation.
4 - 28
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC347
v04.0907
GaAs MMIC SPDT NON-REFLECTIVE
SWITCH, DC - 20 GHz
Suggested Driver Circuit
SWITCHES - CHIP
4
Pad Descriptions
Pad Number
Function
Description
1, 4, 7
RFC, RF1, RF2
This pad is DC coupled and matched to 50 Ohm. Blocking capacitors
are required if the RF line potential is not equal to 0V.
2, 5, 8, 10
CTRLA
See truth table and control voltage table.
3, 6, 9
CTRLB
See truth table and control voltage table.
GND
Die bottom must be connected to RF ground.
Interface Schematic
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
4 - 29
HMC347
v04.0907
GaAs MMIC SPDT NON-REFLECTIVE
SWITCH, DC - 20 GHz
Assembly Diagram
SWITCHES - CHIP
4
4 - 30
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC347
v04.0907
GaAs MMIC SPDT NON-REFLECTIVE
SWITCH, DC - 20 GHz
Mounting & Bonding Techniques for Millimeterwave GaAs MMICs
50 Ohm Microstrip transmission lines on 0.127mm (5 mil) thick alumina thin film
substrates are recommended for bringing RF to and from the chip (Figure 1). If
0.254mm (10 mil) thick alumina thin film substrates must be used, the die should be
raised 0.150mm (6 mils) so that the surface of the die is coplanar with the surface
of the substrate. One way to accomplish this is to attach the 0.102mm (4 mil) thick
die to a 0.150mm (6 mil) thick molybdenum heat spreader (moly-tab) which is then
attached to the ground plane (Figure 2).
0.102mm (0.004”) Thick GaAs MMIC
Wire Bond
0.076mm
(0.003”)
RF Ground Plane
Microstrip substrates should be brought as close to the die as possible in order to
minimize bond wire length. Typical die-to-substrate spacing is 0.076mm (3 mils).
Handling Precautions
0.127mm (0.005”) Thick Alumina
Thin Film Substrate
Follow these precautions to avoid permanent damage.
Storage: All bare die are placed in either Waffle or Gel based ESD protective
containers, and then sealed in an ESD protective bag for shipment. Once the
sealed ESD protective bag has been opened, all die should be stored in a dry
nitrogen environment.
Cleanliness: Handle the chips in a clean environment. DO NOT attempt to clean
the chip using liquid cleaning systems.
Static Sensitivity: Follow ESD precautions to protect against ESD strikes.
Figure 1.
0.102mm (0.004”) Thick GaAs MMIC
Wire Bond
0.076mm
(0.003”)
Transients: Suppress instrument and bias supply transients while bias is applied.
Use shielded signal and bias cables to minimize inductive pick-up.
General Handling: Handle the chip along the edges with a vacuum collet or with
a sharp pair of bent tweezers. The surface of the chip has fragile air bridges and
should not be touched with vacuum collet, tweezers, or fingers.
Mounting
The chip is back-metallized and can be die mounted with AuSn eutectic preforms or
with electrically conductive epoxy. The mounting surface should be clean and flat.
RF Ground Plane
4
SWITCHES - CHIP
The die should be attached directly to the ground plane eutectically or with
conductive epoxy (see HMC general Handling, Mounting, Bonding Note).
0.150mm (0.005”) Thick
Moly Tab
0.254mm (0.010”) Thick Alumina
Thin Film Substrate
Figure 2.
Eutectic Die Attach: A 80/20 gold tin preform is recommended with a work surface temperature of 255 deg. C and a tool temperature
of 265 deg. C. When hot 90/10 nitrogen/hydrogen gas is applied, tool tip temperature should be 290 deg. C. DO NOT expose the
chip to a temperature greater than 320 deg. C for more than 20 seconds. No more than 3 seconds of scrubbing should be required
for attachment.
Epoxy Die Attach: Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy fillet is observed around the
perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer’s schedule.
Wire Bonding
Ball or wedge bond with 0.025 mm (1 mil) diameter pure gold wire (DC bias, IF1 and IF2) or Ribbon Bond (RF and LO ports) 0.076
mm x 0.013 mm (3 mil x 0.5 mil) size is recommended. Thermosonic wirebonding with a nominal stage temperature of 150 °C and
a ball bonding force of 40 to 50 grams or wedge bonding force of 18 to 22 grams is recommended. Use the minimum level of ultrasonic energy to achieve reliable wirebonds. Wirebonds should be started on the chip and terminated on the package or substrate.
All bonds should be as short as possible <0.31 mm (12 mils).
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
4 - 31