100mA / 50V Digital transistors (with built-in resistors) DTC114EM / DTC114EE / DTC114EUA / DTC114EKA Applications Inverter, Interface, Driver Features 1) Built-in bias resistors enable the configuration of an inverter circuit without connecting external input resistors (see equivalent circuit). 2) The bias resistors consist of thin-film resistors with complete isolation to allow negative biasing of the input. They also have the advantage of almost completely eliminating parasitic effects. 3) Only the on/off conditions need to be set for operation, making the device design easy. Structure NPN epitaxial planar silicon transistor (Resistor built-in type) Dimensions (Unit : mm) DTC114EM DTC114EE 0.7 1.6 0.55 0.3 0.2 (3) 0.8 0.8 1.2 0.2 (1)(2) 0.4 0.4 0.5 (2) 0.13 (1) IN (2) GND (3) OUT 0.8 ROHM : VMT3 Each lead has same dimensions 2.0 0.2 1.1 0.4 0.8 (3) 1.6 2.8 2.1 1.25 ROHM : UMT3 EIAJ : SC-70 (1) GND (2) IN (3) OUT Each lead has same dimensions 2.9 DTC114EKA 0.7 0.15 0.1Min. (1) 0.65 0.65 1.3 1.0 ROHM : EMT3 (3) (2) 0.15 Abbreviated symbol : 24 0.9 0.3 0.2 0.5 0.5 Abbreviated symbol : 24 DTC114EUA (1) 0.2 Each lead has same dimensions Abbreviated symbol : 24 www.rohm.com c 2011 ROHM Co., Ltd. All rights reserved. ○ (2) (1) GND (2) IN (3) OUT (1) 0.95 0.95 0.15 1.9 ROHM : SMT3 EIAJ : SC-59 1/3 0.3Min. 0.22 0.1Min. (3) 1.6 1.2 0.32 (1) GND (2) IN (3) OUT Each lead has same dimensions Abbreviated symbol : 24 2011.12 - Rev.E DTC114EM / DTC114EE / DTC114EUA / DTC114EKA Packaging specifications Parameter Symbol Equivalent circuit Limits DTC114EM Unit DTC114EE DTC114EUA DTC114EKA Supply voltage VCC 50 V Input voltage VIN −10 to +40 V IO 50 IC(Max.) 100 Output current Data Sheet OUT R1 IN R2 GND mA Power dissipation PD Junction temperature Tj 150 °C Storage temperature Tstg −55 to +150 °C 150 mW 200 OUT IN GND R1=R2=10kΩ Absolute maximum ratings (Ta=25C) Parameter Input voltage Output voltage Symbol Min. Typ. Max. VI(off) − − 0.5 VI(on) 3 − − VO(on) − 0.1 0.3 V Unit Conditions VCC=5V, IO=100μA V VO=0.3V, IO=10mA IO/II=10mA/0.5mA II − − 0.88 mA VI=5V IO(off) − − 0.5 μA VCC=50V, VI=0V DC current gain GI 30 − − − VO=5V, IO=5mA Input resistance R1 7 10 13 kΩ Resistance ratio R2/R1 0.8 1 1.2 − − 250 − MHz Input current Output current Transition frequency fT ∗ − − VCE=10V, IE=−5mA, f=100MHz ∗ Characteristics of built-in transistor Electrical characteristics (Ta=25C) Part No. Package VMT3 EMT3 UMT3 SMT3 Packaging type Taping Taping Taping Taping Code T2L TL T106 T146 Basic ordering unit (pieces) 8000 3000 3000 3000 − − − − − DTC114EM DTC114EE − DTC114EUA − − DTC114EKA − − www.rohm.com c 2011 ROHM Co., Ltd. All rights reserved. ○ − − 2/3 2011.12 - Rev.E DTC114EM / DTC114EE / DTC114EUA / DTC114EKA Data Sheet Electrical characteristic curves 100 OUTPUT CURRENT : Io (A) INPUT VOLTAGE : VI(on) (V) 20 10 5 2 10m 5m VO=0.3V 50 Ta=−40°C 25°C 100°C 1 500m 200m 100m 100μ 200μ 500μ 1m 2m VCC=5V 2m 1m Ta=100°C 25°C −40°C 500μ 200μ 100μ 50μ 20μ 10μ 5μ 2μ 1μ 0 5m 10m 20m 50m 100m 0.5 OUTPUT CURRENT : IO (A) Fig.1 Input voltage vs. output current (ON characteristics) 1k 200 100 50 20 10 5 2 2.0 1 2.5 3.0 lO/lI=20 500m OUTPUT VOLTAGE : VO(on) (V) DC CURRENT GAIN : GI Ta=100°C 25°C −40°C 1.5 Fig.2 Output current vs. input voltage (OFF characteristics) VO=5V 500 1.0 INPUT VOLTAGE : VI(off) (V) Ta=100°C 25°C −40°C 200m 100m 50m 20m 10m 5m 2m 1 100μ 200μ 500μ1m 2m 5m 10m 20m 50m100m 1m 100μ 200μ OUTPUT CURRENT : IO (A) Fig.3 DC current gain vs. output current www.rohm.com c 2011 ROHM Co., Ltd. All rights reserved. ○ 500μ 1m 2m 5m 10m 20m 50m 100m OUTPUT CURRENT : IO (A) Fig.4 Output voltage vs. output current 3/3 2011.12 - Rev.E Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. R1120A